Experimental study on the energy conversion of food waste via supercritical water gasification: Improvement of hydrogen production

In this study, the model food waste was gasified to hydrogen-rich syngas in a batch reactor under supercritical water condition. The model food consisted of rice, chicken, cabbage, and cooking oil. The effects of the main operating parameters including temperature (420–500 °C), residence time (20–60 min) and feedstock concentration (2–10 wt%) were investigated. Under the optimal condition at 500 °C, 2 wt% feedstock and 60 min residence time, the highest H₂ yield of 13.34 mol/kg and total gas yield of 28.27 mol/kg were obtained from non-catalytic experiments. In addition, four commercial catalysts namely FeCl₃, K₂CO₃, activated carbon, and KOH were employed to investigate the catalytic effect of additives at the optimal condition. The results showed that the highest hydrogen yield of 20.37 mol/kg with H₂ selectivity of 113.19%, and the total gas yield of 38.36 mol/kg were achieved with 5 wt% KOH addition Moreover, the low heating value of gas products from catalytic experiments with KOH increased by 32.21% compared to the non-catalytic experiment. The catalytic performance of the catalysts can be ranked in descending order as KOH > activated carbon > FeCl₃ > K₂CO₃. The supercritical water gasification (SCWG) with KOH addition can be a potential applied technology for food waste treatment with production of hydrogen-rich gases.     

Screening of supported transition metal catalysts for hydrogen production from glucose via catalytic supercritical water gasification

In total 17 heterogeneous catalysts, with combinations of 4 transition metals (Ni, Ru, Cu and Co) and various promoters (e.g., Na, K, Mg, or Ru) supported on different materials (γ-Al₂O₃, ZrO₂, and activated carbon (AC)), were investigated with respect to their catalytic activity and stability for H₂ production from glucose via supercritical water gasification (SCWG). The experiments were carried out at 600 °C and 24 MPa in a bench-scale continuous-flow tubular reactor. Ni (in metallic form) and Ru (in both metallic and oxidized forms) supported on γ-Al₂O₃ exhibited very high activity and H₂ selectivity among all of the catalysts investigated for a time-on-stream of 5-10 h. With Ni20/γ-Al₂O₃ (i.e., γ-Al₂O₃ with 20 wt% Ni), a H₂ yield of 38.4 mol/kg glucose was achieved, approximately 20 times higher than that obtained during the blank test without catalyst (1.8 mol/kg glucose). In contrast, Cu and Co catalysts were much less effective for glucose SCWG reactions. As for the effects of catalyst support materials on activity, the following order of sequence was observed: γ-Al₂O₃ > ZrO₂ > AC. In addition, Mg and Ru were found to be effective promoters for the Ni/γ-Al₂O₃ catalyst, suppressing coke and tar formation.     

Enhancing hydrogen production by dry reforming process with strontium promoter

Hydrogen is an ideal energy carrier and can play a very important role in the energy system. The present study investigated the enhancement of hydrogen production from catalytic dry reforming process. Two catalysts namely Ni/γ-Al₂O₃ and Co/γ-Al₂O₃ promoted with different amounts of strontium were used to explore selectivity and yield of hydrogen production. Spent and fresh catalysts were characterized using techniques such as BET, XRD, H₂-TPR, CO₂-TPD, TGA and O₂-TPO. The catalyst activity and characterization results displayed stability improvement due to addition of Sr promoter. The least coke formations i.e. 3.8 wt% and 5.1 wt% were obtained using 0.75 wt% Sr doped in Ni/γ-Al₂O₃ and 0.5 wt% Sr doped in Co/γ-Al₂O₃ catalysts respectively. Time on stream tests of promoted catalysts for about six hours at 700 °C showed stable hydrogen selectivity. Moreover, the hydrogen selectivity was significantly improved by the addition of Sr in Ni and Co based catalysts. For instance the hydrogen selectivity increased from 45.9% to 47.8% for Ni/γ-Al₂O₃ and from 48% to 50.9% for Co/γ-Al₂O₃ catalyst by the addition of 0.75 wt% Sr in Ni/γ-Al₂O₃ and 0.5 wt% Sr in Co/γ-Al₂O₃ catalyst respectively.     

Catalytic gasification of food waste in supercritical water over La promoted Ni/Al2O3 catalysts for enhancing H2 production

Ni/Al₂O₃ catalyst is the one of promising catalysts for enhancing H₂ production from supercritical water gasification (SCWG) of biomass. However, due to carbon deposition, the deactivation of Ni/Al₂O₃ catalyst is still a serious issue. In this work, the effects of lanthanum (La) as promoter on the properties and catalytic performance of Ni/Al₂O₃ in SCWG of food waste were investigated. La promoted Ni/Al₂O₃ catalysts with different La loading content (3–15 wt%) were prepared via impregnation method. The catalysts were characterized using XRD, SEM, BET techniques. The SCWG experiments were carried out in a Hastelloy batch reactor in the operating temperature range of 420–480 °C, and evaluated based on H₂ production. The stability of the catalysts was assessed by the amount of carbon deposition on catalyst surface and their catalytic activity after reuse cycles. The results showed that 9 wt% La promoter is the optimal loading as Ni/9La–Al₂O₃ catalyst performed best performance with the highest H₂ yield of 8.03 mol/kg, and H₂ mole fraction of 42.46% at 480 °C. La promoted Ni/Al₂O₃ catalysts have better anti-carbon deposition properties than bare Ni/Al₂O₃ catalyst, resulting in better gasification efficiency after reuse cycles. Ni/9La–Al₂O₃ catalyst showed high catalytic activity in SCWG of food waste and had good stability as it was still active for enhancing H₂ production when used in SCWG for the third time, which indicated that La promoted Ni/Al₂O₃ catalysts are potential additive to improve the SCWG of food waste.     

Biohydrogen synthesis from catalytic steam gasification of furniture waste using nickel catalysts supported on modified CeO2

Present study evaluated the catalytic steam gasification of furniture waste to enhance the biohydrogen production. To do this, 10 wt% nickel loaded catalysts on the variety of supports (Al₂O₃, CeO₂, CeO₂-La₂O₃, and CeO₂–ZrO₂) were prepared by the novel solvent deficient method. The hydrogen selectivity (vol%) order of the catalysts was achieved as Ni/CeO₂–ZrO₂>Ni/CeO₂>Ni/Al₂O₃?Ni/CeO₂-La₂O₃. The best catalytic activity of Ni/CeO₂–ZrO₂ catalyst (~82 vol % H₂ at 800 °C) was ascribed to the smaller size of nickel crystals, finely dispersed Ni on the catalyst surface, and Ce_1-xZr_xO_2-δ solid solution. The role of Ce_1-xZr_xO_2-δ solid solution in Ni/CeO₂–ZrO₂ catalyst was observed as bi-functional; acceleration of water-gas-shift and oxidation of carbon reaction. The high resistance of Ni/CeO₂–ZrO₂ towards the coke formation showed its potential to establish a cost-effective commercial-scale biomass steam gasification process. This study is expected to provide a promising solution for the disposal of furniture wastes for production of clean energy (biohydrogen).     

Catalytic performances of Ni-based catalysts on supercritical water gasification of phenol solution and coal-gasification wastewater

Activity and stability of the supported Ni-based catalysts for the gasification performances of phenol solution and coal-gasification wastewater in supercritical water were studied in a continuous reactor at 480 °C, 25 MPa and oxygen ratio of 0.2 for 50 h operation. The influences of the supports (γ-Al₂O₃, active carbon (AC) and carbon nanotube (CNT)) on gas yields, gasification efficiencies for phenol solution were investigated, and the loading amount of Ni were optimized. Results showed that the catalytic activity and the stability of the catalysts followed the order of Ni/CNT > Ni/AC > Ni/γ-Al₂O₃. The activity of Ni/AC and Ni/γ-Al₂O₃ decreased after 30 h continuous operation, and there occurred significant leaching of Ni²⁺. For Ni/CNT catalyst, H₂ yield increased obviously when the loading amount of Ni lower than 15 wt%, while increased little at higher loading amount. Then, 15 wt% Ni/CNT with a thickness of 1.5 mm was coated on 316 L stainless steel (SS316L, an economic material usually used as the reactor material), which can act as a "catalytic tube wall" in reactor. The catalytic activity and corrosion resistance of Ni/CNT/SS316L for the gasification of real coal-gasification wastewater were studied. Results showed that Ni/CNT/SS316L gave a great positive effect on H₂ production. H₂ yield increased from 25.36 mmol/g (total organic carbon) without catalyst to 75.12 mmol/g (total organic carbon) with Ni/CNT/SS316L after operated for 20 h, respectively. However, obvious pealing of the coating was found after 50 h operation. Further study is necessary for the improvement of the coating preparation method.     

The influence of Ni loading on coke formation in steam reforming of acetic acid

Steam reforming of acetic acid on Ni/γ-Al₂O₃ with different nickel loading for hydrogen production was investigated in a tubular reactor at 600 °C, 1 atm, H2O/HAc = 4, and WHSV = 5.01 g-acetic acid/g-cata.h^?1. The catalysts were characterized by temperature programmed oxidation (TPO) and differential thermal analysis (DTA), X-ray photoelectron spectroscopy (XPS) and transmission electron microscopy (TEM). The results showed that the amount of deposited carbidic-like carbon decreased and graphitic-like carbon increased with Ni loading increasing from 9 to 15 wt%. The Ni/γ-Al₂O₃ catalyst with 12 wt% Ni loading had higher catalytic activity and lower coke deposited rate.     

Hydrogen production by steam reforming of liquefied natural gas (LNG) over Ni/Al2O3–ZrO2 xerogel catalysts: Effect of calcination temperature of Al2O3–ZrO2 xerogel supports

Al₂O₃–ZrO₂ (AZ) xerogel supports prepared by a sol-gel method were calcined at various temperatures. Ni/Al₂O₃–ZrO₂ (Ni/AZ) catalysts were then prepared by an impregnation method for use in hydrogen production by steam reforming of liquefied natural gas (LNG). The effect of calcination temperature of AZ supports on the catalytic performance of Ni/AZ catalysts in the steam reforming of LNG was investigated. Crystalline phase of AZ supports was transformed in the sequence of amorphous γ-Al₂O₃ and amorphous ZrO₂ → θ-Al₂O₃ and tetragonal ZrO₂ → (θ + α)-Al₂O₃ and (tetragonal + monoclinic) ZrO₂ → α-Al₂O₃ and (tetragonal + monoclinic) ZrO₂ with increasing calcination temperature from 700 to 1300 °C. Nickel oxide species were strongly bound to γ-Al₂O₃ and θ-Al₂O₃ in the Ni/AZ catalysts through the formation of solid solution. In the steam reforming of LNG, both LNG conversion and hydrogen composition in dry gas showed volcano-shaped curves with respect to calcination temperature of AZ supports. Nickel surface area of Ni/AZ catalysts was well correlated with catalytic performance of the catalysts. Among the catalysts tested, Ni/AZ1000 (nickel catalyst supported on AZ support that had been calcined at 1000 °C) with the highest nickel surface area showed the best catalytic performance. Well-developed and pure tetragonal phase of ZrO₂ in the AZ1000 support played an important role in the adsorption of steam and the subsequent spillover of steam from the support to the active nickel.     

Support and alloy effects on activity and product selectivity for ethanol steam reforming over supported nickel cobalt catalysts

Ni, Co and bimetallic Ni–Co catalysts supported on Ca-γ-Al₂O₃ and ZrO₂ were investigated for the production of hydrogen via ethanol steam reforming (ESR). Catalysts were prepared by wet impregnation method and characterized using temperature-programmed reduction (TPR), X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS). ESR and temperature-programmed desorption of ethanol (ethanol-TPD) were carried out in a continuous flow fixed bed micro-reactor and the outlet gases were monitored by an on-line GC or MS. Ni is found to be more active for the C–C bond rupture than Co on both supports, Ca-γ-Al₂O₃ and ZrO₂. Catalyst support plays very important roles for the ESR. Strong interaction between support and metal affects the formation of NiCo bimetallic compound, resulting in the variety of catalytic activity. On Ca-γ-Al₂O₃ support, the catalytic activity of ESR follows the sequence of 10%Ni > 6.7%Ni 3.3%Co ∼ 3.3%Ni 6.7%Co > 10%Co. On ZrO₂, the trend is 10%Ni > 6.7%Ni 3.3%Co > 10%Co > 3.3%Ni 6.7%Co. The H₂O adsorption/activation ability of the support determines the reaction pathway and thus the product selectivity. On Ca-γ-Al₂O₃, water gas shift reaction is more favorable than on ZrO₂, due to the availability of surface OH groups. The roles of the metal and support for ESR are also discussed.     

Effect of Ni loading on SBA-15 synthesized from palm oil fuel ash waste for hydrogen production via CH4 dry reforming

The successful synthesis of SBA-15 using silica source extracted from palm oil fuel ash (POFA) was proven with the presence of mesostructure characteristics as evidenced by low angle XRD, N₂ adsorption-desorption isotherms and TEM. Different amounts of Ni were loaded on the synthesized SBA-15(POFA) using the impregnation method at 80 °C. The influence of Ni loading over the Ni/SBA-15(POFA) physiochemical properties and CO₂ reforming of CH₄ (CRM) were investigated in a stainless steel fixed-bed reactor at 800 °C and atmospheric pressure with 1:1 CO₂:CH₄ volumetric feed composition. An increment in Ni loading on SBA-15(POFA) from 1 to 5 wt% decreased the BET surface area and crystallinity of catalyst as proven by N₂ adsorption–desorption and XRD analysis. The catalytic performance of CRM followed the sequence of 3 wt% > 5 wt% > 2 wt% > 1 wt% -Ni/SBA-15(POFA). This result was owing to the even distribution of Ni and good Ni–O–Si interaction of 3 wt% Ni/SBA-15(POFA) as proved by TEM, FTIR and XPS. Lowest H₂/CO ratio and catalyst activity and stability of 1 wt% Ni/SBA-15(POFA) were due to the weaker Ni–O–Si interaction and small amount of basic sites that favor the reverse water gas shift (RWGS) reaction and carbon formation. The recent finding indicates that a quantity as small as 3 wt% Ni loaded onto SBA-15(POFA) could elicit outstanding catalytic performance in CRM, which was comparable with 10 wt% Ni loading catalysts reported in literature.     

Hydrogen production from oxidative steam reforming of methanol: Effect of the Cu and Ni impregnation on ZrO2 and their molecular simulation studies

Cu and Ni were supported on ZrO₂ by co-impregnation and sequential impregnation methods, and tested in the oxidative steam reforming of methanol (OSRM) reaction for H₂ production as a function of temperature. Surface area of the catalysts showed differences as a function of the order in which the metals were added to zirconia. Among them, the Cu/ZrO₂ catalyst had the lowest surface area. XRD patterns of the bimetallic catalysts did not show diffraction peaks of the Cu, Ni or bimetallic Cu–Ni alloys. In addition, TPR profiles of the bimetallic catalysts had the lowest reduction temperature compared with the monometallic samples. The reactivity of the catalysts in the range of 250–350 °C showed that the bimetallic samples prepared by successive impregnation had highest catalytic activity among all the catalysts studied. These results were also confirmed by theoretical calculations. The reactivity of the monometallic and bimetallic structures obtained by molecular simulation followed the next order: Ni_shellCu_core/ZrO₂ ≅ Cu_shellNi_core/ZrO₂ > Ni/Cu/ZrO₂ > Cu/Ni/ZrO₂ > Cu–Ni/ZrO₂ > Cu/ZrO₂ > Ni/ZrO₂. These findings agree with the experimental results, indicating that the bimetallic catalysts prepared by successive impregnation show a higher reactivity than the Cu–Ni system obtained by co-impregnation. In addition, the selectivity for H₂ production was higher on these catalysts. This result could be associated also to the presence of the bimetallic Cu–Ni and core–shell Ni/Cu nanoparticles on the catalysts, as was evidenced by TEM–EDX analysis, suggesting that the OSRM reaction may be a structure–sensitive reaction.     

Catalytic reforming of glycerol in supercritical water with nickel-based catalysts

The catalytic performance of nickel catalysts supported on La₂O₃, α-Al₂O₃, γ-Al₂O₃, ZrO₂, and YSZ for supercritical water reforming of glycerol was investigated. Experiments were conducted in a tubular reactor made of Inconel-625 with the temperature range of 723–848 K under a pressure of 25 MPa. Carbon formation causing operation failure was observed for α-Al₂O₃, γ-Al₂O₃ and ZrO₂ at temperatures higher than 748, 798 and 823 K, respectively. Ni/La₂O₃ exhibited the highest H₂ yield where almost complete conversion was obtained at 798 K. Moderate space velocities (WHSV = 6.45 h⁻¹) and glycerol feed concentration (5wt.%) favor high hydrogen selectivity and yield. Methanation is favored at a low WHSV or high glycerol feed concentration, resulting in a lower H₂ yield. Increasing Ni loading on the Ni/La₂O₃ catalyst strongly promoted the reforming, water–gas shift, and methanation reactions, which contributed significantly to the product species distribution.     

Supercritical water synthesized Ni/ZrO2 catalyst for hydrogen production from supercritical water gasification of glycerol

Catalysts are crucial to promote the technical feasibility of supercritical water gasification (SCWG) for H₂ production from wet biomass, yet catalysts prepared by conventional methods normally encounter sintering problems in supercritical water. Herein, a series of ZrO₂-supported Ni catalysts were tried to be prepared by supercritical water synthesis (SCWS) and evaluated for SCWG in terms of activity and property stability. The SCWS was conducted at 500 °C and 23 MPa using metal nitrates as starting materials. Effect of precursor concentration on property and catalytic performance of the SCWS-prepared catalysts for SCWG of 20 wt% glycerol were systematically studied. XRD, SEM-EDS, TEM and TGA were applied for catalyst characterization. Results verified the successful obtaining of Ni/ZrO₂ nanocatalysts with Ni crystals of 30–70 nm and ZrO₂ crystals of ~11 nm by the SCWS process, which were found to be active on the WGSR for SCWG to increase the H₂ yield as high as 155%. Importantly, the SCWS-prepared Ni/ZrO₂ catalysts exhibited excellent property stability and anti-coking ability for SCWG of glycerol.     

Zirconia supported nickel catalysts for glycerol steam reforming: Effect of zirconia structure on the catalytic performance

The effect of the zirconia structure in Ni/ZrO₂ catalysts on the glycerol steam reforming (GSR) reaction was studied. A tetragonal zirconia support was synthesized via a hydrolysis technique and loaded with 5 wt% Ni via a wet-impregnation method. Similarly, a commercial monoclinic zirconia support was also impregnated with 5 wt% Ni. Following calcination at 600 °C, physico-chemical properties of the prepared catalysts were investigated by X-Ray Diffraction (XRD), H₂-Temperature Programmed Reduction (H₂-TPR) and CO₂-Temperature Programmed Desorption (CO₂-TPD) techniques. The catalysts were then tested in the GSR reaction in the 400–700 °C range with a steam to glycerol molar ratio of 9:1 and a flow rate of 0.025 mL/min. The monoclinic catalyst exhibited a better performance giving higher hydrogen yields and glycerol conversions. This was attributed to an improved reducibility of Ni in this catalyst. Stability tests at 600 °C revealed the deactivation of the tetragonal catalyst during 6 h as a result of the formation of encapsulating coke which blocked active Ni metal sites. The monoclinic catalyst, exhibiting the formation of only filamentous coke, remained relatively stable for 24 h.     

Hydrogen production from catalytic steam reforming of bio-oil aqueous fraction over Ni/CeO2–ZrO2 catalysts

A series of composite catalysts Ni/CeO₂–ZrO₂ were prepared via impregnation method with Ni as the active metal. A laboratory-scale fixed-bed reactor was employed to investigate the catalyst performance during hydrogen production by steam reforming bio-oil aqueous fraction. Effects of water-to-bio-oil ratio (W/B), reaction temperature, and the loaded weight of Ni and Ce on the hydrogen production performance of Ni/CeO₂–ZrO₂ catalysts were examined. The obtained results were compared with commercial nickel-based catalysts (Z417). The best performance of Ni/CeO₂–ZrO₂ catalyst was observed when the Ni and Ce loaded weight were 12% and 7.5% respectively. At W/B = 4.9, T = 800 °C, H₂ yield reaches the highest of 69.7% and H₂ content of 61.8% were obtained. Under the same condition, H₂ yield and H₂ content were higher than commercial nickel-based catalysts (Z417).     

Various nickel doping in commercial Ni–Mo/Al2O3 as catalysts for natural gas decomposition to COx-free hydrogen production

Non-oxidative decomposition of natural gas to CO_x-free hydrogen production over commercial nickel-molybdate hydrotreating catalysts with different Ni loading from 5 to 40wt% were studied at 700 °C. The catalysts were characterized by XRD, BET, TEM, Raman spectroscopy and TG-DTA analysis. The catalytic decomposition activities showed that a tremendous hydrogen production (∼90%) was obtained over 20–40wt%Ni/Mo–Al₂O₃ catalysts. Moreover, all catalysts exhibited excellent durability up to 9 h with stable catalytic activity toward H₂ production. Although the increase of Ni content reduces the catalyst surface area, the H₂ productivity and longevity increases with increased Ni content, i.e., the catalytic decomposition activity primarily depends on the active Ni sites which overcompensates the surface deficiencies. TEM, TGA and XRD data of used catalysts indicated that a higher thermal stability and graphitization degree of multi-walled carbon nanotubes were obtained on all Ni containing catalysts. Higher metal loading produced carbon nanofibers beside CNTs due to increment of particle size and long reaction time.     

Tuning of active nickel species in MOF-derived nickel catalysts for the control on acetic acid steam reforming and hydrogen production

Acetic acid (AcOH) steam reforming for hydrogen (H₂) generation was investigated using a zero valent nickel complex (Ni-comp) derived from a metal-organic framework precursor supported over aluminum oxide/lanthanum oxide-cerium dioxide (ALC). The effects of Ni loading ratio (10, 15, and 20 wt%) on the catacatalytic activity were investigated in the range of 400 to 650 °C to H₂ generation. The Ni-comp/ALC catalysts exhibited almost complete conversion of AcOH (X_AcOH >98%) to H₂ (X_H2>90%) alongside some impurities (e.g., carbon monoxide, methane, and carbon dioxide). A maximum H₂ yield (91.36% (0.064 mol^-1 g_cat⁻¹ h⁻¹)) was attained at the following conditions: 15 wt% Ni loading, steam to carbon molar ratio of 6.5, weight hourly space velocity of 1.05 h⁻¹, and 600 °C. The 15 wt% Ni catalyst maintained sufficient stability over 40 h reaction time. Accordingly, Ni-comp-ALC interactions were seen to efficiently improve the activity and stability of the catalyst so as to synergistically resist coke deposition and metal sintering through the formation of a large number of free Ni particles and oxygen vacancies.     

Autothermal reforming of iso-octane and gasoline over Rh-based catalysts: Influence of CeO2/γ-Al2O3-based mixed oxides on hydrogen production

Autothermal reforming (ATR) of iso-octane in the presence of Rh-based catalysts (0.5 wt% of Rh) supported onto γ-Al₂O₃, CeO₂, and ZrO₂ were initially carried out at 700 °C with a S/C ratio of 2.0, an O/C ratio of 0.84, and a gas hourly space velocity (GHSV) of 20,000 h⁻¹. The activity of Rh/γ-Al₂O₃ was found to be higher than Rh/CeO₂ and Rh/ZrO₂, with H₂ and (H₂ + CO) yields of 1.98 and 2.48 mol/mol C, respectively, after 10 h. This Rh/γ-Al₂O₃ material, however, was potentially susceptible to carbon coking and produced 3.5 wt% of carbon deposits following the reforming reaction, as evidenced by C, H, N, and S elemental analysis. In contrast, Rh/CeO₂ catalyst exhibited lower activity but higher stability than Rh/γ-Al₂O₃, with nearly no carbon being formed within 10 h. To combine the superior activity originated from Rh/γ-Al₂O₃ with high stability from Rh/CeO₂, Rh/CeO₂/γ-Al₂O₃ catalysts with different CeO₂ contents were synthesized and examined for the ATR reactions of iso-octane. Compared to Rh/γ-Al₂O₃, the newly prepared Rh/CeO₂/γ-Al₂O₃ catalysts (0.5 wt% of Rh and 20 wt% of CeO₂) showed even enhanced activity during 10 h, and H₂ and (H₂ + CO) yields were calculated to be 2.08 and 2.62 mol/mol C, respectively. In addition, as observed with Rh/CeO₂, the catalyst was further found to be stable with less than 0.3 wt% of carbon deposition after 10 h. The Rh/γ-Al₂O₃ and Rh/CeO₂/γ-Al₂O₃ catalysts were eventually tested for ATR reactions using commercial gasoline that contained sulfur, aromatics, and other impurities. The Rh/γ-Al₂O₃ catalyst was significantly deactivated, showing decreased activity after 4 h, while the Rh/CeO₂/γ-Al₂O₃ catalyst proved to be excellent in terms of stability against coke formation as well as activity towards the desired reforming reaction, maintaining its ability for H₂ production for 100 h.     

Steam reforming of ethanol over copper-zirconia based catalysts doped with Mn,Ni, Ga

The activity toward hydrogen production in steam reforming of ethanol (SRE) reaction has been evaluated for CuO/ZrO₂ catalysts doped with Mn, Ni, Ga at 350 °C. The copper based catalysts were synthesised by co-precipitation method at constant pH = 7 and fixed (wt.%) CuO/ZrO = 2.3. The catalysts were characterised by means of N₂ adsorption, temperature programmed reduction (H₂-TPR), N₂O dissociative chemisorption, X-ray diffraction (XRD), CO₂ temperature programmed desorption (CO₂-TPD), and temperature programmed oxidation (TPO). It has been found that copper based catalysts exhibit high ethanol conversion in SRE (>86%) at 350 °C. Due to basic character of catalysts, the formation of acetaldehyde is observed. The CuO/ZrO₂ catalyst modification with dopants increases the hydrogen yield with maximum (52%) for CuO/ZrO₂/NiO. The addition of Ni changes the distribution of carbon-containing products. In this case, the increase in selectivity to CO, CO₂ and CH₄ is observed whereas selectivity to acetaldehyde is significantly decreased. This shows that presence of Ni facilities the C–C bond cleavage. On the other hand, the formation of acetic acid is limited upon addition of Mn and Ga. For all modified catalysts, decrease in carbon deposition rate during SRE is pronounced according to TPO experiments. The modification of Cu/Zr with Mn, Ni and Ga causes the decrease in copper particle size, which hinders the carbon deposit formation.     

Sustainable and selective hydrogen production by steam reforming of bio-based ethylene glycol: Design and development of Ni–Cu/mixed metal oxides using M (CeO2, La2O3, ZrO2)–MgO mixed oxides

Hydrogen (H₂) production in a clean and green manner via renewable sources is at present of great interest. Ethylene glycol, a bio-based feedstock, offers a sustainable route for high purity H₂ production. In the current investigation, MgO based mixed metal oxides containing CeO₂, La₂O₃ and ZrO₂ were synthesized and used to support 20 wt% Ni–Cu (1:1). The impacts of altering support characteristics on catalytic behavior have been studied and compared in H₂ synthesis via ethylene glycol steam reforming (SR), employing various characterization techniques such as XRD, SEM, EDX, TEM, H₂-TPR, H₂-TPD, TG-DSC and BET. Further, high resolution XPS studies were performed to explore the valence states and effectiveness of surface engineering of the catalysts. Assessment of the efficacy of catalysts was done via several parameters such as reactant conversion, H₂ concentration and long-term stability. All the synthesized materials produced encouraging results with high H₂ yield and conversion under the said operating conditions [T- 623 to 773 K; GHSV - 3120 to 6240 h^?1; P - 0.1 MPa; S/C - 3 to 7.5 mol/mol]. Amongst the three catalysts, Ni–Cu/La₂O₃–MgO and Ni–Cu/CeO₂–MgO exhibited superior behavior for high H₂ production. Ni–Cu/La₂O₃–MgO was better in comparison to Ni–Cu/CeO₂–MgO in terms of reactant conversion whereas Ni–Cu/CeO₂–MgO showed highest H₂ concentration (98 mol %) and improved stability along with absence of carbon deposition owing to its high mobile oxygen vacancies in its lattice. The highly active cubic CeO₂ species and its long-term durability (up to 8 cycles) owing to its exceptional redox property further justified its efficacy. The optimized process showed that at T = 773 K, GHSV = 3120 h^?1, S/C = 4.5 mol/mol for Ni–Cu/La₂O₃–MgO and Ni–Cu/CeO₂–MgO and at T = 773 K, GHSV = 3120 h^?1, S/C = 6 mol/mol and for Ni–Cu/ZrO₂–MgO, maximum H₂ concentration was obtained. At the end, reaction pathway followed by the catalysts was proposed.