Hydrogen environment embrittlement of stable austenitic steels

Seven stable austenitic steels (stable with respect to γ → α′ transformation at room temperature) of different alloy compositions (18Cr–12.5Ni, 18Cr–35Ni, 18Cr–8Ni–6Mn–0.25N, 0.6C–23Mn, 1.3C–12Mn, 1C–31Mn–9Al, 18Cr–19Mn–0.8N) were tensile tested in high-pressure hydrogen atmosphere to assess the role of austenite stability on hydrogen environment embrittlement (HEE). The influence of hydrogen on tensile ductility was small in steels that are believed to have a high initial portion of dislocation cross slip (18Cr–12.5Ni, 18Cr–35Ni, 18Cr–8Ni–6Mn–0.25N), while the effects of hydrogen were significantly greater in steels with other primary deformation modes (planar slip in 18Cr–19Mn–0.8N and 1C–31Mn–9Al or mechanical twinning in 0.6C–23Mn and 1.3C–12Mn) despite comparable austenite stability at the given test conditions. It appears that initial deformation mode is one important parameter controlling susceptibility to HEE and that martensitic transformation is not a sufficient explanation for HEE of austenitic steels.     

Investigation on hydrogen induced cracking behaviors of Ni-base alloy

Hydrogen embrittlement of a Ni-base alloy at room temperature was investigated by slow strain rate tensile test (SSRT) under precharging or dynamic charging conditions. It was found that hydrogen embrittlement susceptibility of this alloy increased with increasing charging current density in both charging conditions. In-situ observation of hydrogen induced cracking revealed that surface crack initiation at both grain boundaries and slip bands, which should be attributed to decomposition of hydride phase during aging at room temperature. SSRT result exhibited that hydrogen diffusion in the alloy could be facilitated by deformation and as a result induced transgranular fracture of the sample. Both hydrogen induced cracking and the interaction between hydrogen and deformation played combined roles on hydrogen embrittlement of this alloy.     

Hydrogen embrittlement behavior in interstitial Mn–N austenitic stainless steel

The susceptibility to hydrogen embrittlement behavior was investigated in an interstitial Mn–N austenitic steel HR183 and stainless steel 316L. Hydrogen was introduced by cathodic hydrogen charging at 363 K. HR183 has stronger austenite stability than 316L despite its lower nickel content, the addition of manganese and nitrogen inhibited martensitic transformation during the slow strain rate tensile deformation. Due to the diffusion of hydrogen being delayed by the interstitial solution of nitrogen atoms and the uniform dislocation slips, hydrogen permeates more slowly in HR183 than 316L, contributing to an 84.79 μm thinner brittle fracture layer in HR183 steel. Hydrogen charging caused elongation losses in both 316L and HR183 steels associated with the hydrogen-enhanced localized plasticity (HELP) and hydrogen-enhanced decohesion (HEDE) mechanism. However, the hydrogen embrittlement susceptibility of HR183 is 3.4 times lower than that of 316L according to the difference in elongation loss between the two steel after hydrogen charging. Deformation twins trapped a lot amount of hydrogen leading to brittle intergranular fracture in 316L. The multiple directions of slip in HR183 steel suppressed the strain localization inside grains and delayed the adverse effects conducted by HELP and HEDE mechanism, eventually inhibiting server hydrogen embrittlement in the HR183 steel. This study is assisting in the development of low-cost stainless steel with excellent hydrogen embrittlement resistance that can be used in harsh hydrogen-containing environments.     

Effect of grain size on hydrogen embrittlement in stable austenitic high-Mn TWIP and high-N stainless steels

Two stable austenitic steels, 20Cr-11Ni-5Mn-0.3N (wt%) stainless steel (STS) and 18Mn-1.5Al-0.6C (wt%) twinning-induced plasticity steel (TWIP), were investigated to understand the effect of grain size on hydrogen embrittlement (HE). Grain refinement promoted HE in the STS but suppressed HE in the TWIP. These opposite effects occurred because the steel composition affected deformation mechanism. Cr-N pair enhanced short-range ordering (SRO) in STS, which promoted planar slip and delayed mechanical twinning. In contrast, TWIP exhibited mechanical twinning which was more active in coarser grains. Final dislocation density after tensile deformation was increased by grain refinement in STS, but was decreased in TWIP. The damaging effects of hydrogen on strain energy at interfaces and on interfacial bonding strength were controlled by dislocation density; therefore, increase in dislocation density led to increase in susceptibility to HE.     

Hydrogen embrittlement and hydrogen diffusion behavior in interstitial nitrogen-alloyed austenitic steel

The susceptibility to hydrogen embrittlement and diffusion behavior of hydrogen were evaluated in interstitial nitrogen-alloyed austenitic steel QN1803 and 304 and 316 L stainless steels. The amount of transformed martensite and the activation energy of hydrogen diffusion were revealed via electron backscattering diffraction and thermal desorption spectroscopy. The austenite stability of QN1803 during the deformation process was higher than that of 304 and 316 L. However, the hydrogen content of QN1803 was high because of the small grain size and low activation energy of hydrogen diffusion. For the stable QN1803 and 316 L austenitic steels, martensite had no evident harmful effect because of its discrete distribution. A planar dislocation slip was observed in QN1803 during deformation. Hydrogen charging enhanced dislocation mobility, leading to severe strain localization. Thus, the severe strain in QN1803 promoted microcracking.     

Comparative study of embrittlement of quenched and tempered steels in hydrogen environments

The study of steels which guarantee safety and reliability throughout their service life in hydrogen-rich environments has increased considerably in recent years. Their mechanical behavior in terms of hydrogen embrittlement is of utmost importance. This work aims to assess the effects of hydrogen on the tensile properties of quenched and tempered 42CrMo4 steels. Tensile tests were performed on smooth and notched specimens under different conditions: pre-charged in high pressure hydrogen gas, electrochemically pre-charged, and in-situ hydrogen charged in an acid aqueous medium. The influence of the charging methodology on the corresponding embrittlement indexes was assessed. The role of other test variables, such as the applied current density, the electrolyte composition, and the displacement rate was also studied. An important reduction of the strength was detected when notched specimens were subjected to in-situ charging. When the same tests were performed on smooth tensile specimens, the deformation results were reduced. This behavior is related to significant changes in the operative failure micromechanisms, from ductile (microvoids coalescence) in absence of hydrogen or under low hydrogen contents, to brittle (decohesion of martensite lath interfaces) under the most stringent conditions.     

Influence of copper as an alloying element on hydrogen environment embrittlement of austenitic stainless steel

A Cu alloyed (18Cr–10Ni–3Cu) and a Cu free (18Cr–12.7Ni) austenitic stainless steel were tensile tested in gaseous hydrogen atmosphere at 20 °C and −50 °C. Depending on the test temperature, the Cu alloyed steel was extremely embrittled whereas the Cu free steel was only slightly embrittled. Austenite stability and inherent deformation mode are two main criteria for the resistance of austenitic stainless steels against hydrogen environment embrittlement. Based on the well known austenite stability criteria, the austenite stability of both steels should be very similar. Interrupted tensile tests show that martensite formation upon plastic deformation was much more severe in the Cu alloyed steel proving that the influence of Cu on austenite stability is overestimated in the empirical stability equations. When tested in high pressure H₂, replacing Ni by Cu resulted in a fundamental change in fracture mode atmosphere, i.e. Ni cannot be replaced by Cu to reduce the costs of SS without compromising the resistance to hydrogen environment embrittlement.     

Hydrogen embrittlement of super duplex stainless steel in acid solution

Super duplex stainless steel (SDSS) is a good choice of material when resistance to harsh environments is needed. Despite the material’s excellent corrosion resistance and high strength, a number of in-service failures have been recorded. The root cause of these failures was environmentally induced cracking initiated at manufacturing and in-service metallurgical defects. In this study the hydrogen embrittlement of pre-strained super duplex stainless steel specimens was investigated after 48 h cathodic charging in 0.1 M H₂SO₄. The metallurgical changes that resulted from four levels of cold work (4, 8, 12, and 16% plastic strain) were considered and their effect on the embrittlement of the SDSS alloy was investigated. After hydrogen charging, the specimens were pulled immediately to failure and the mechanical properties evaluated. The obtaining fracture morphology was investigated using low and high magnification microscopy. Experimental results indicated that charging the super duplex stainless steel alloy with hydrogen caused varying degrees of embrittlement depending on cold work level. Increasing cold work resulted in a reduction of the elongation to failure. Microscopic investigation confirmed the significant effect of cold work on the hydrogen embrittlement susceptibility of the super duplex stainless steel alloy investigated.     

Origin of deformation twins and their influence on hydrogen embrittlement in cold-rolled austenitic stainless steel

The effect of cold rolling on hydrogen embrittlement in stable 18Cr–1Mn–11Ni-0.15 N austenitic stainless steels was investigated. Alloy plates were cold-rolled to 15% or 30% reduction, then pre-charged with hydrogen and subjected to tensile testing with slow strain rate. Hydrogen-induced degradation of tensile elongation became increasingly severe with the increase in the degree of cold rolling. During cold rolling, deformation twins with various orientations were actively generated, and twins with specific orientations were vulnerable to hydrogen-induced cracking. Cold rolling also increased the density of defects, and thereby facilitated penetration of hydrogen into the steels. The combination of cracks generated at the twin boundaries, and the promoted hydrogen diffusion caused severe hydrogen embrittlement in the cold-rolled steels.     

Slow strain rate technique for studying hydrogen induced cracking in 34CrMo4 high strength steel

Alloy hardened steels offer excellent combination of mechanical properties, hardenability and corrosion resistance. 34CrMo4 is a medium carbon, low alloy steel widely used due to a good combination of high-strength, toughness and wear resistance. However, this steel experiences hydrogen embrittlement (HE), a complex phenomenon depending on the composition and microstructure. This work estimates de loss of the mechanical properties caused by hydrogen in electrochemically H-charged specimens in absence of mechanical stress but also, at low strain rate and constant load. H-charging for 2 and 6 h induce YS losses of about 40% and 71% and UTS losses of 39% and 59%, respectively. The synergistic effect of the stress and the H-charging process leads to a higher loss, 91%, and a faster brittle fracture even though hydrogen content is similar to those firstly H-charged and then tested in air.     

Hydrogen embrittlement of the coarse grain heat affected zone of a quenched and tempered 42CrMo4 steel

The coarse grain heat affected zone (CG-HAZ) of welds produced in a quenched and tempered 42CrMo4 steel was simulated by means of a laboratory heat treatment consisting in austenitizing at 1200 °C for 20 min, oil quenching and finally applying a post weld heat treatment at 700 °C for 2 h (similar to the tempering treatment previously applied to the base steel). A tempered martensite microstructure with a prior austenite grain size of 150 μm and a hardness of 230 HV, similar to the aforementioned CG-HAZ weld region, was produced. The effect of the prior austenite grain size on the hydrogen embrittlement (HE) behaviour of the steel was studied comparing this coarse-grained microstructure with that of the fine-grained base steel, with a prior austenite grain size of 20 μm.The specimens used in this study were charged with hydrogen gas in a reactor at 19.5 MPa and 450 °C for 21 h. Cylindrical specimens were used to determine hydrogen uptake and hydrogen desorption behaviour. Smooth and notched tensile specimens tested under different displacement rates were also used to evaluate HE.Embrittlement indexes, EI, were generally quite low in the case of hydrogen pre-charged tensile tests performed on smooth tensile specimens. However, very significant embrittlement indexes were obtained with notched tensile specimens. It was observed that these indexes always increase as the applied displacement rate decreases. Moreover, hydrogen embrittlement indexes also increase with increasing prior austenite grain size. In fact, the embrittlement index related to the reduction in area, EI_(RA), reached values of over 20% and 50% for the fine and coarse grain size steels, respectively, when tested under the lowest displacement rates (0.002 mm/min).A comprehensive fractographic analysis was performed and the main operative failure micromechanisms due to the presence of internal hydrogen were determined at different test displacement rates. While microvoids coalescence (MVC) was found to be the typical ductile failure micromechanism in the absence of hydrogen in the two steels, brittle decohesion mechanisms (carbide-matrix interface decohesion, CMD, and martensitic lath interface decohesion, MLD) were observed under internal hydrogen. Intergranular fracture (IG) was also found to be operative in the case of the coarse-grained steel tested under the lowest displacement rate, in which hydrogen accumulation in the process zone ahead of the notch tip is maximal.     

Effect of hydrogen in advanced high strength steel materials

The effect of hydrogen in AHSS material (automobile and structural component) was discussed. Dual Phase steels were highly susceptible to hydrogen-related failure when working on hydrogen environment. The influence of hydrogen on TRIP steel was seen during fractographic examination where the brittle transgranular fracture was presented. TWIP steels results were inconsistent. The mechanisms which were responsible for crack growth are discussed. LIST and SSRT testing were performed for mechanical properties evaluation and SEM and TEM were used for microstructural examination of fractured samples. Simultaneous preventing methods to reduce hydrogen embrittlement such as coating, alloying and providing diffusion layer were discussed.     

Effects of grain size and dislocation density on the susceptibility to high-pressure hydrogen environment embrittlement of high-strength low-alloy steels

The tensile properties of several high-strength low-alloy steels in a 45 MPa hydrogen atmosphere at ambient temperature were examined with respect to the effects of grain size and dislocation density on hydrogen environment embrittlement. Grain size was measured using an optical microscope and dislocation density was determined by X-ray diffractometry. Both grain refinement and a reduction in dislocation density are effective in reducing the susceptibility to embrittlement. The steel that has high dislocation density or large grain size inclines to show a smooth intergranular fracture surface. Given only the grain size and dislocation density, a simple approximation of the embrittlement property of high-strength steel could be obtained. This method could be useful in selecting candidate materials in advance of the mechanical tests in high-pressure hydrogen gas.     

Crack propagation analysis of hydrogen embrittlement based on peridynamics

We introduced a coupled peridynamic hydrogen diffusion and fracture model to solve the hydrogen embrittlement fracture of low alloy steel AISI 4340. In this model, the influence of temperature on hydrogen diffusion coefficient is considered, and a new peridynamic constitutive analysis method is used to simulate the crack propagation of hydrogen embrittlement. We verified the model in 3D using the experimental test of the hydrogen embrittlement cracking process of AISI 4340 steel in 0.1 N H₂SO₄ solution from the literature. Considering different ambient temperatures, it is found that the crack propagation is highly similar to the experimental results. Based on the numerical analysis of peridynamics, the model can numerically simulate the hydrogen embrittlement fracture of AISI 4340 steel, and obtain a visual demonstration of the entire process of hydrogen atom diffusion and crack growth.     

From the perspective of new technology of blending hydrogen into natural gas pipelines transmission: Mechanism,experimental study,and suggestions for further work of hydrogen embrittlement in high-strength pipeline steels

Blending hydrogen into high-strength pipeline steels for high-pressure transmission may cause materials' hydrogen embrittlement (HE) failure. Although the hydrogen-induced failure of metallic materials has been studied for a long time, the process of hydrogen into the materials, hydrogen-induced delayed failure, and dynamic mechanisms of high-strength pipeline steels under high pressure have not been fully understood. This paper aims to provide a detailed review of the latest research on the hydrogen-induced failure of high-strength pipeline steels in hydrogen-blended natural gas transmission. First, introduced the typical hydrogen blending natural gas pipeline transmission projects and their associated research conclusions. Then, described the physical process of the HE in high-strength pipeline steels and the principle, development, and latest research progress of typical hydrogen embrittlement mechanisms in detail. Third, reviewed the research methods and progress of experimental and theoretical simulations for the HE in steels, including hydrogen permeation (HP) experiments, hydrogen content measurements, hydrogen distribution detection, mechanical property tests, and molecular dynamics simulations. The shortcomings of existing experimental and theoretical simulation methods in the hydrogen-induced analysis of high-strength natural gas pipeline steels under high pressure are discussed. Finally, the future research directions and challenges of this problem are proposed from three aspects: the multimechanism synergy mechanism, the improvement of experimental methods, and the establishment of a new interatomic multiscale model.     

Development of a stable high-aluminum austenitic stainless steel for hydrogen applications

A novel high-aluminum austenitic stainless steel has been produced in the laboratory with the aim of developing a lean-alloyed material with a high resistance to hydrogen environment embrittlement. The susceptibility to hydrogen environment embrittlement was evaluated by means of tensile tests at a slow strain rate in pure hydrogen gas at a pressure of 40 MPa and a temperature of −50 °C. Under these conditions, the yield strength, tensile strength and elongation to rupture are not affected by hydrogen in comparison to companion tests carried out in air. Moreover, a very high ductility in hydrogen is evidenced by a reduction of area of 70% in the high-pressure and low-temperature hydrogen environment. The lean degree of alloying is reflected in the molybdenum-free character of the material and a nickel content of 8.0 wt.%. With regard to the alloy concept, a combination of high-carbon, high-manganese, and high-aluminum contents confer an extremely high stability against the formation of strain-induced martensite. This aspect was investigated by means of in-situ magnetic measurements and ex-situ X-ray diffraction. The overall performance of the novel alloy was compared with two reference materials, 304L and 316L austenitic stainless steels, both industrially produced. Its capability of maintaining a fully austenitic structure during tensile testing has been identified as a key aspect to avoid hydrogen environment embrittlement.     

Hydrogen embrittlement behaviors at different deformation temperatures in as-quenched low-carbon martensitic steel

The present study investigated hydrogen-related fractures at different deformation temperatures ranging from ?100 °C to 100 °C in low-carbon martensitic steel. The sensitivity to hydrogen embrittlement increased as the temperature decreased from 100 °C to 0 °C, while it decreased as the temperature decreased further below 0 °C. We characterized the fracture surface types from the morphological and crystallographic aspects and found that the fraction of hydrogen-embrittled surfaces exhibited a similar temperature dependence on the sensitivity to hydrogen embrittlement. The qualitative discussion suggested that the degree of hydrogen accumulation exhibits a peak value in the medium temperature range, which has the same tendency as the sensitivity to hydrogen embrittlement confirmed experimentally. Thus, we proposed that the effect of deformation conditions on the sensitivity to hydrogen embrittlement could be explained on the basis of the hydrogen accumulation behavior.     

Hydrogen embrittlement of Cr-Mn-N-austenitic stainless steels

Cr-Mn-N austenitic steels show a unique combination of properties, i.e. high strength, high ductility, non magnetic and good corrosion resistance at costs being much lower compared to Cr-Ni austenitic steels. Hydrogen environment embrittlement (HEE) was investigated by slow displacement tensile testing in hydrogen atmosphere at 10 MPa and −50 °C. The fracture appearance of stable Cr-Mn-N austenitic steels with lower Mn contents (12Mn-0.7N) was transgranular whereas higher Mn contents (18Mn-0.7N) resulted in twin boundary fracture. This change in fracture morphology was related to a modest change in macroscopic ductility. Such fracture behaviour is similar to what is known from metastable Cr-Ni austenitic steels, therefore, Mn and/or N cannot be used to replace Ni in stable austenitic high HEE resistant steels.     

Material performance of age-hardened beryllium–copper alloy,CDA-C17200, in a high-pressure,gaseous hydrogen environment

In order to develop safer and more energy-efficient, hydrogen pre-cooling systems for use in hydrogen refueling stations, it is necessary to identify a high-strength metallic material with greater thermal conductivity and lower susceptibility to hydrogen embrittlement, as compared with ordinary, stable austenitic stainless steels. To accomplish this task, the hydrogen compatibility of a precipitation-hardened, high-strength, copper-based alloy was investigated by slow-strain-rate tensile (SSRT), fatigue-life, fatigue-crack-growth (FCG) and fracture toughness tests in 115-MPa hydrogen gas at room temperature. The hydrogen solubility and diffusivity of the alloy were also determined. The hydrogen solubility of the alloy was two or three orders of magnitude lower than that of austenitic stainless steels. The alloy also demonstrated absolutely no hydrogen-induced degradation of its strength properties, a factor which could contribute to the reduction of costs related to the construction and maintenance of hydrogen refueling stations, owing to the downsizing and improved cooling performance of the pre-cooling systems.     

Hydrogen diffusion in Fe4N: Implication for an effective hydrogen diffusion barrier

The diffusion behavior of hydrogen in steel plays a significant role in understanding the mechanism of hydrogen embrittlement which may lead to the failure of steel. In the present work, density functional theory based first-principles calculations were performed to investigate the hydrogen diffusion in Fe₄N at atomic level. The results showed that the hydrogen atom in the Fe₄N structure didn't diffuse until the temperature increased up to 1350K, indicating a layer of Fe₄N covering on the iron could be a good candidate to trap the highly diffusive hydrogen atoms and prevent the aggregation of hydrogen which is the precursor of hydrogen embrittlement.