Effect of addition of hydrogen and exhaust gas recirculation on characteristics of hydrogen gasoline engine

The effects of exhaust gas recirculation (EGR) on combustion and emissions under different hydrogen ratios were studied based on an engine with a gasoline intake port injection and hydrogen direct injection. The peak cylinder pressure increases by 9.8% in the presence of a small amount of hydrogen. The heat release from combustion is more concentrated, and the engine torque can increase by 11% with a small amount of hydrogen addition. Nitrogen oxide (NOx) emissions can be reduced by EGR dilution. Hydrogen addition offsets the blocking effect of EGR on combustion partially, therefore, hydrogen addition permits a higher original engine EGR rate, and yields a larger throttle opening, which improves the mechanical efficiency and decreases NOx emissions by 54.8% compared with the original engine. The effects of EGR on carbon monoxide (CO) and hydrocarbon (HC) emissions are not obvious and CO and HC emissions can be reduced sharply with hydrogen addition. CO, HC, and NOx emissions can be controlled at a lower level, engine output torque can be increased, and fuel consumption can be reduced significantly with the co-control of hydrogen addition and EGR in a hydrogen gasoline engine.     

Effect of induction on exhaust gas recirculation and hydrogen gas in compression ignition engine with simarouba oil in dual fuel mode

Biofuels extracted from non-edible oil is sustainable and can be used as an alternative fuel for internal combustion engines. This study presents the performance, emission and combustion characteristic analysis by using simarouba oil (obtained from Simarouba seed) as an alternative fuel along with hydrogen and exhaust gas recirculation (EGR) in a compression ignition (CI) engine operating on dual fuel mode. Simarouba biofuel blend (B20) was prepared on volumetric basis by mixing simarouba oil and diesel in the proportion of 20% and 80% (v/v), respectively. Hydrogen gas was introduced at the flow rate of 2.67 kg/min, and EGR concentration was maintained at 30% of total air introduction. Performance, combustion and emission characteristics analysis were examined with biodiesel (B20), biodiesel with hydrogen substitution and biodiesel, hydrogen with EGR and were compared with neat diesel operation. Results indicate that BTE of the engine operating with biodiesel B20 was decreased when compared to neat diesel operation. However, introducing hydrogen along with B20 blend into the combustion chamber shows a slight increase in the BTE by 1%. NO_x emission was increased to 18.13% with the introduction of hydrogen than that of base fuel (diesel) operation. With the introduction of EGR, there is a significant reduction in NO_x emission due to decrease in in-cylinder temperature by 19.07%. A significant reduction in CO, CO_2, and smoke emissions were also noted with the introduction of both hydrogen and EGR. The ignition delay and combustion duration were increased with the introduction of hydrogen, EGR with biodiesel than neat diesel operation. Hence, the proposed biodiesel B20 with H₂ and EGR combination can be applied as an alternative fuel in CI engines.     

废气再循环在柴油机中的应用

本文回顾了废气再循环（EGR）在减少排放，特别是减少NOx排放上的潜力以及限定这一技术的应用范围。详细分析了RGR装置对柴油机的排放和性能的影响，通过深入分析，发现在柴油机进气中引入废气再循环（EGR），相当如置换了部分吸入的空气，这种方式能充分减少NOx的排放。因此，废气再循环的使用是最有效改善尾气排放的技术措施之一。     

Experimental study of engine performance and emissions for hydrogen diesel dual fuel engine with exhaust gas recirculation

With an alarming enlargement in vehicular density, there is a threat to the environment due to toxic emissions and depleting fossil fuel reserves across the globe. This has led to the perpetual exploration of clean energy resources to establish sustainable transportation. Researchers are continuously looking for the fuels with clean emission without compromising much on vehicular performance characteristics which has already been set by efficient diesel engines. Hydrogen seems to be a promising alternative fuel for its clean combustion, recyclability and enhanced engine performance. However, problems like high NOx emissions is seen as an exclusive threat to hydrogen fuelled engines. Exhaust gas recirculation (EGR), on the other hand, is known to overcome the aforementioned problem. Therefore, this study is conducted to study the combined effect of hydrogen addition and EGR on the dual fuelled compression ignition engine on a single cylinder diesel engine modified to incorporate manifold hydrogen injection and controlled EGR. The experiments are conducted for 25%, 50%, 75% and 100% loads with the hydrogen energy share (HES) of 0%, 10% and 30%. The EGR rate is controlled between 0%, 5% and 10%. With no substantial decrement in engine's brake thermal efficiency, high gains in terms of emissions are observed due to synergy between hydrogen addition and EGR. The cumulative reduction of 38.4%, 27.4%, 33.4%, 32.3% and 20% with 30% HES and 10% EGR is observed for NOx, CO2, CO, THC and PM, respectively. Hence, the combination of hydrogen addition and EGR is observed to be advantageous for overall emission reduction.     

稀燃和EGR对汽油发动机性能影响研究

基于一台带有低压废气再循环系统的1.5 L涡轮增压直喷汽油发动机进行了稀燃和废气再循环(EGR)影响发动机燃烧性能的试验研究。结果表明,随着稀释率的上升,EGR和稀燃均导致发动机滞燃期、燃烧持续期延长,燃烧重心提前,有效燃油消耗率下降,排气温度下降,平均绝热指数上升。相同稀释率下,相比稀燃,EGR的滞燃期长,燃烧重心提前,两者燃烧持续期基本相等,稀释极限低,绝热指数小,排气温度低。在稀释率分别为20%、35.9%时,最大可减小有效燃油消耗率4.7%、7.2%。热容对燃油经济性的影响占主导地位,相同稀释率下,循环变动系数小于3%时,相比稀燃,EGR具有更好的燃油经济性。     

Improving gasoline direct injection (GDI) engine efficiency and emissions with hydrogen from exhaust gas fuel reforming

Exhaust gas fuel reforming has been identified as a thermochemical energy recovery technology with potential to improve gasoline engine efficiency, and thereby reduce CO₂ in addition to other gaseous and particulate matter (PM) emissions. The principle relies on achieving energy recovery from the hot exhaust stream by endothermic catalytic reforming of gasoline and a fraction of the engine exhaust gas. The hydrogen-rich reformate has higher enthalpy than the gasoline fed to the reformer and is recirculated to the intake manifold, i.e. reformed exhaust gas recirculation (REGR).     

Effect of manifold and port injection of hydrogen and exhaust gas recirculation (EGR) in dairy scum biodiesel - low energy content gas-fueled CI engine operated on dual fuel mode

In this current work, exhaustive research work is conducted in three phases, in the initial phase, WFO was used for producing WFO treated biomass and in the second phase, influence of PFIP and PFIT has been examined. Further in the successive phase, effect of hydrogen HMI, HPI and EGR on the combustion and emission characteristics of CRDI diesel engine operated on dual-fuel mode using DiSOME and PG combination is evaluated. In the current study, in a CRDI engine, PFIT was employed ranging from 0 to 15°CA bTDC and changed in steps of 5 and PFIP was used from 600 to 1000 bar and varied in successive steps of 200 bar. Further flow rate of hydrogen was kept 8 L/min constant and HMIT was employed in the range from TDC to 15°aTDC and changed in stages of 5. Correspondingly, HID was varied from 30 to 90°CA with 30°CA dwell and EGR was used in the range from 0 to 15% by vol. and varied in steps of 5. Outcome of the work showed that, DiSOME-PG operation with 10°bTDC PFIT, 800 bar PFIP, 10°aTDC of HMI, 60°CAHID and 5% EGR rate showed lower BTE by 5.8% and increased smoke levels by 10.8%, HC by 8.6%, CO by 6.5% and marginally decreased NOx by 6.4% was observed in comparison to the same fuel blend with zero EGR at 80% load. Further, marginally amplifiedID and CD with loweredCP and HRR has been noticed. Study revealed thatH₂addition to low calorific value gas (PG), method of pilot fuel addition and EGR is affected dual fuel engine performance, but provided drastic reductions in smoke and NOx emissions.     

Experimental study of various effects of exhaust gas recirculation (EGR) on combustion and emissions of an automotive direct injection diesel engine

Cooled exhaust gas recirculation (EGR) is a common way to control in-cylinder NO_x production and is used on most modern high-speed direct injection (HSDI) diesel engines. However EGR has different effects on combustion and emissions production that are difficult to distinguish (increase of intake temperature, delay of rate of heat release (ROHR), decrease of peak heat release, decrease in O₂ concentration (and thus of global air/fuel ratio (AFR)) and flame temperature, increase of lift-off length, etc.), and thus the influence of EGR on NO_x and particulate matter (PM) emissions is not perfectly understood, especially under high EGR rates. An experimental study has been conducted on a 2.0 l HSDI automotive diesel engine under low-load and part load conditions in order to distinguish and quantify some effects of EGR on combustion and NO_x/PM emissions. The increase of inlet temperature with EGR has contrary effects on combustion and emissions, thus sometimes giving opposite tendencies as traditionally observed, as, for example, the reduction of NO_x emissions with increased inlet temperature. For a purely diffusion combustion the ROHR is unchanged when the AFR is maintained when changing in-cylinder ambient gas properties (temperature or EGR rate). At low-load conditions, use of high EGR rates at constant boost pressure is a way to drastically reduce NO_x and PM emissions but with an increase of brake-specific fuel consumption (BSFC) and other emissions (CO and hydrocarbon), whereas EGR at constant AFR may drastically reduce NO_x emissions without important penalty on BSFC and soot emissions but is limited by the turbocharging system.     

Effect of hydrogen nanobubble addition on combustion characteristics of gasoline engine

Hydrogen is an attractive energy source for improving gasoline engine performance. In this paper, a new hydrogen nanobubble gasoline blend is introduced, and the influence of hydrogen nanobubble on the combustion characteristics of a gasoline engine is experimentally investigated. The test was performed at a constant engine speed of 2000 rpm, and engine load of 40, 60, and 80%. The air-to-fuel equivalence ratio (λ) was adjusted to the stoichiometric (λ = 1), for both gasoline, and the hydrogen nanobubble gasoline blend. The results show that the mean diameter and concentration of hydrogen nanobubble in the gasoline blend are 149 nm and about 11.35 × 10⁸ particles/ml, respectively. The engine test results show that the power of a gasoline engine with hydrogen nanobubble gasoline blend was improved to 4.0% (27.00 kW), in comparison with conventional gasoline (25.96 kW), at the engine load of 40%. Also, the brake specific fuel consumption (BSFC) was improved, from 291.10 g/kWh for the conventional gasoline, to 269.48 g/kWh for the hydrogen nanobubble gasoline blend, at the engine load of 40%.     

Analysis of the particulate emissions and combustion performance of a direct injection spark ignition engine using hydrogen and gasoline mixtures

Three different fractions (2%, 5%, and 10% of stoichiometric, or 2.38%, 5.92%, and 11.73% by energy fraction) of hydrogen were aspirated into a gasoline direct injection engine under two different load conditions. The base fuel was 65% iso-octane, and 35% toluene by volume fraction. Ignition sweeps were conducted for each operation point. The pressure traces were recorded for further analysis, and the particulate emission size distributions were measured using a Cambustion DMS500. The results indicated a more stable and faster combustion as more hydrogen was blended. Meanwhile, a substantial reduction in particulate emissions was found at the low load condition (more than 95% reduction either in terms of number concentration or mass concentration when blending 10% hydrogen). Some variation in the results occurred at the high load condition, but the particulate emissions were reduced in most cases, especially for nucleation mode particulate matter. Retarding the ignition timing generally reduced the particulate emissions. An engine model was constructed using the Ricardo WAVE package to assist in understanding the data. The simulation reported a higher residual gas fraction at low load, which explained the higher level of cycle-by-cycle variation at the low load.     

Effect of exhaust gas recirculation (EGR) temperature for various EGR rates on heavy duty DI diesel engine performance and emissions

DI diesel engines are well established today as the main powertrain solution for trucks and other relevant heavy duty vehicles. At the same time emission legislation (mainly for NO_x and particulate matter) becomes stricter, reducing their limit to extremely low values. One efficient method to control NO_x in order to achieve future emissions limits is the use of rather high exhaust gas recirculation (EGR) rates accompanied by increased boost pressure to avoid the negative impact on soot emissions. The method is based on the reduction of gas temperature level and O₂ availability inside the combustion chamber, but unfortunately it has usually an adverse effect on soot emissions and brake specific fuel consumption (bsfc). The use of high EGR rates creates the need for EGR gas cooling in order to minimize its negative impact on soot emissions especially at high engine load were the EGR flow rate and exhaust temperature are high. For this reason in the present paper it is examined, using a multi-zone combustion model, the effect of cooled EGR gas temperature level for various EGR percentages on performance and emissions of a turbocharged DI heavy duty diesel engine operating at full load. Results reveal that the decrease of EGR gas temperature has a positive effect on bsfc, soot (lower values) while it has only a small positive effect on NO. As revealed, the effect of low EGR temperature is stronger at high EGR rates.     

Experimental study on lean-burn characteristics of an SI engine with hydrogen/gasoline combined injection and EGR

Hydrogen has shown potential for improving the combustion and emission characteristics of the spark ignition (SI) dual-fuel engine. To reduce the additional NO_x emissions caused by hydrogen direct injection, in this research, the cooperative control of the addition of hydrogen with exhaust gas recirculation (EGR) in the hydrogen/gasoline combined injection engine was investigated. The results indicate that both the addition of hydrogen and the use of EGR can increase the brake mean effective pressure (BMEP). As the α_H2 value increases from 0% to 25%, the maximum BMEP increases by 9%, 12.70%, 16.50%, 11.30%, and 8.20%, respectively, compared with the value without EGR at λ = 1.2. The CA0-10 tends to increase with increases in the EGR rate. However, the effect of EGR in increasing the CA0-10 can be offset by the addition of 15% hydrogen at λ = 1.2. Measurements of the coefficient of variation of the indicated mean effective pressure (COV_IMEP) indicate that the addition of hydrogen can effectively extend the EGR limit. Regarding gaseous emissions, NO_x emissions, after the introduction of EGR and the addition of hydrogen, are lower than those of pure gasoline without EGR. An 18% EGR rate yields a significant reduction in NO_x, reaching maximum decreases of about 82.7%, 77.8%, and 60% compared to values without EGR at λ = 1.0, 1.2, and 1.4, respectively. As the EGR rate increases, the hydrocarbon (HC) emissions continuously increase, whereas a blend of 5% hydrogen can significantly reduce the HC emissions at high EGR rates at λ = 1.4. Finally, according to combustion and emissions, the coupling of a 25% addition of hydrogen with 30% EGR at λ = 1.2, and the coupling of a 20% addition of hydrogen with an 18% EGR rate at λ = 1.4 yield the best results.     

Increasing the power output of hydrogen internal combustion engines by means of supercharging and exhaust gas recirculation

Spark ignition engines can be relatively easily converted to hydrogen using port fuel injection (PFI). However, because of the lower volumetric energy density of a hydrogen–air mixture and the occurrence of abnormal combustion phenomena such as backfire, hydrogen-fueled PFI engines suffer from a power deficit in comparison with gasoline engines. This paper reports measurements on a single-cylinder hydrogen engine equipped with a supercharger and an exhaust gas recirculation (EGR) system. Using EGR combined with supercharging and a three-way catalyst (TWC) is shown to significantly increase the power output while limiting tailpipe emissions of oxides of nitrogen (NO_x).     

Improving the combustion performance of a gasoline rotary engine by hydrogen enrichment at various conditions

The combustion process within the cylinder directly influences the thermal efficiency and performance of the engines. As for the rotary engine, the long-narrow combustion chamber prevents the mixture from fully burning, which worsens the performance of the rotary engine. As a fuel with excellent properties, hydrogen can improve the combustion of the original engine. In this paper, improvements in combustion of a gasoline rotary engine by hydrogen supplement under different operating conditions were experimentally investigated. The experiment was conducted on a modified hydrogen-gasoline dual-fuel rotary engine equipped with an electronically-controlled fuel injection system. An electronic control module was specially made to command the fuel injection, excess air ratio and hydrogen volumetric fraction. Integral heat release fraction (IHRF) was employed to evaluate the combustion of the tested engine. The tested engine was first run at the idle speed of 2400 rpm and then operated at 4500 rpm to investigate the combustion of the hydrogen-blended gasoline rotary engine under different hydrogen volume fractions, excess air ratios and spark timings. The testing results demonstrated that the combustion of the gasoline rotary engine were all improved when the hydrogen was blended into the chamber under all tested conditions.     

An experimental investigation on hydrogen as a dual fuel for diesel engine system with exhaust gas recirculation technique

With higher rate of depletion of the non-renewable fuels, the quest for an appropriate alternative fuel has gathered great momentum. Though diesel engines are the most trusted power sources in the transportation industry, due to stringent emission norms and rapid depletion of petroleum resources there has been a continuous effort to use alternative fuels. Hydrogen is one of the best alternatives for conventional fuels. Hydrogen has its own benefits and limitations in its use as a conventional fuel in automotive engine system.In the present investigation, hydrogen-enriched air is used as intake charge in a diesel engine adopting exhaust gas recirculation (EGR) technique with hydrogen flow rate at 20 l/min. Experiments are conducted in a single-cylinder, four-stroke, water-cooled, direct-injection diesel engine coupled to an electrical generator. Performance parameters such as specific energy consumption, brake thermal efficiency are determined and emissions such as oxides of nitrogen, hydrocarbon, carbon monoxide, particulate matter, smoke and exhaust gas temperature are measured. Usage of hydrogen in dual fuel mode with EGR technique results in lowered smoke level, particulate and NO_x emissions.     

The effect of HRG gas addition on diesel engine combustion characteristics and exhaust emissions

Extensive studies have been dedicated in the last decade to the possibility to use hydrogen in the dual-fuel mode to improve combustion characteristics and emissions of a diesel engine. The results of these studies, using pure hydrogen or hydrogen containing gas produced through water electrolysis, are notably different.The present investigation was conducted on a tractor diesel engine running with small amounts of the gas—provided by a water electrolyzer—aspirated in the air stream inducted in the cylinder. The engine was operated at light and medium loads and various speeds.It was found that the addition of HRG gas has a slight negative impact, up to 2%, on the engine brake thermal efficiency. Smoke is significantly reduced, up to 30%, with HRG enrichment, while NO_x concentrations vary in both senses, up to 14%, depending on the engine operation mode. A relative small amount of HRG gas can be used with favorable effects on emissions and with a small penalty in thermal efficiency.     

Hydrogen rich exhaust gas recirculation (H2EGR) for performance improvement and emissions reduction of a compression ignition engine

Hydrogen (H₂), being carbon free energy carrier, is best suitable for compression ignition (CI) engines with better performance and lower carbon derived emissions. Novelty of present study is the employment of low-cost catalyst (alumina) for production of H₂ reformate (hydrogen rich exhaust gas recirculation: H2EGR) in an indigenous catalytic reactor. Experimental tests were carried out on a CI engine under three conditions; base diesel, exhaust gas recirculation (EGR), and H2EGR. Results indicated that brake thermal efficiency of the engine with H2EGR was higher than EGR and comparable with base diesel operation. All carbon-based emissions including smoke emission decreased significantly with H2EGR than diesel and EGR operations. In addition, oxides of nitrogen emission (NO_x) also decreased by about 46% with H2EGR than base diesel operation. It is concluded that H2EGR is a promising option for CI engines for simultaneous reduction of both NO_x and smoke emissions along with the additional benefit of higher efficiency.     

Effects of exhaust gas recirculation (EGR) on combustion and emissions during cold start of direct injection (DI) diesel engine

Through experiments conducted on a single cylinder direct injection (DI) diesel engine, effects of exhaust gas recirculatoin (EGR) on combustion and emission during cold start were investigated. Combustion of first firing cycle can be promoted significantly by introducing EGR. In experiments, when partially closed choking valve and partially or fully opened EGR valve, peak cylinder pressure of first firing cycle was about 45% higher than that under normal condition without EGR, and the start of combustion (SOC) was also much earlier. EGR also had effects on combustion stability. In the case, which kept 50% or 100% opening of EGR valve (OEV) and kept 100% opening of choking valve (OCV), more stable combustion process was achieved when common rail pressure decreased during cold start. However, excessive amount of EGR led to extreme unstable combustion and even misfiring. Opacity and NO emissions were also analyzed in detail. In the case with maximum EGR, the lowest average opacity, which was less than 4%, was achieved during initial several firing cycles of cold start. But in the later phase, excessive amount of EGR led to a great deal of white smoke emission. NO emission during initial phase of cold start is mainly affected by increase in fuel amount of injection. When combustion became stable gradually, EGR showed significant effect on NO reduction.     

Reducing cyclic variation of a gasoline rotary engine by hydrogen addition under various operating conditions

In the present paper, the cyclic variations of a hydrogen-blended gasoline rotary engine operated under various conditions were experimentally investigated. The experiments were carried out on a modified hydrogen-gasoline dual-fuel rotary engine equipped with an electronically-controlled fuel injection system. An electronic control module was specially made to command the fuel injection, excess air ratio and hydrogen volumetric fraction. The tested engine was first run at idle condition with a speed of 2400 rpm and then operated at 4500 rpm to investigate the cyclic variations of a hydrogen-enriched gasoline rotary engine under different hydrogen volumetric percentages in the total intake, excess air ratios and spark timings. The experimental results demonstrated that the coefficient of variations (in peak pressure, engine speed, flame development period and flame propagation period) of the gasoline rotary engine were distinctly decreased with the increase of hydrogen volume fraction under all the tested conditions. In particular, at idle and stoichiometric conditions, the coefficient of variation in CA0-10 and CA10-90 were reduced from 9.25% to 5.01%, 15.40% to 8.70%, respectively.