Oxidation of lean methane in a two-chamber preheat catalytic reactor

This paper presents the results of lean methane oxidation in a two-chamber preheat catalytic reactor. A preheat catalytic reactor was built, and the effects of the space velocity (3800 h^?1 to 8100 h^?1), the inlet methane concentration (0.6 vol.% to 0.8 vol.%) and the inlet temperature of catalytic oxidation bed (420 °C–540 °C) were experimentally investigated. The results showed that when the space velocity is low, the methane conversion rate maintains a high value. But when the space velocity is higher than 7100 h^?1, the methane conversion rate decreases dramatically. With the increases of the inlet methane concentration and the inlet temperature, the overall temperature of the oxidation bed increases rapidly, the temperature increment of the first catalytic ceramic layer increases, the methane conversion rate increases.     

Dehydrogenation of perhydro-dibenzyltoluene for hydrogen production in a microchannel reactor

A preliminary study regarding the dehydrogenation of perhydro-dibenzyltoluene as a liquid organic hydrogen carrier with switching from a stirred tank reactor to a continuous flow microchannel reactor is presented. The hydrogen production percentage in the case of a continuous flow microchannel reactor was found greater when compared to that of a stirred tank reactor. The hydrogen production was increased from 64.1% to 82.2% with the increase in bottom plate temperature from 260 to 320 °C for 0.01 mL/min flow rate. A maximum of 88% of hydrogen was generated for a 40 hours of operation, at a bottom wall temperature of 290 °C. The kinetic model for the microchannel reactor dehydrogenation was presented with a pre-exponential factor of 3.272 s^?1 and activation energy of 13.79 kJ/mol. The results revealed that a continuous microchannel reactor can be an appropriate technology for the dehydrogenation of perhydro-dibenzyltoluene.     

Molten metal capillary reactor for the high-temperature pyrolysis of methane

In this work, the further development of the molten metal capillary reactor in slug-flow regime is presented. The preliminary results from the high-temperature pyrolysis of methane at 1300 °C and 9 Nml/min are presented with a calculated conversion of 80%, and, a mean residence time of 1.36 s. Due to carbon deposition, difficult gas separation and unstable slug-flow, it was deemed necessary to redesign the system. For that, several alloys were tested looking for improved wettability and more favorable hydrodynamics. The modified experimental set-up is described, which led to improvements in gas separation, but not enough stability in the slug-flow. Finally, the current experimental set-up is introduced. There, a characterization of the hydrodynamics is performed using a low temperature alloy of gallium, indium and tin, GaInSn, and, a stable regular slug-flow is established for various gas and liquid flows. The presence of a film in the slug-flow remains subject to question and the conclusions on the direction of the project are drawn towards an alternative reactor system or further hydrodynamic studies.     

Solar hydrogen production from the thermal splitting of methane in a high temperature solar chemical reactor

This study addresses the single-step thermal decomposition (pyrolysis) of methane without catalysts. The process co-produces hydrogen-rich gas and high-grade carbon black (CB) from concentrated solar energy and methane. It is an unconventional route for potentially cost effective hydrogen production from solar energy without emitting carbon dioxide since solid carbon is sequestered.A high temperature solar chemical reactor has been designed to study the thermal splitting of methane for hydrogen generation. It features a nozzle-type graphite receiver which absorbs the solar power and transfers the heat to the flow of reactant at a temperature that allows dissociation. Theoretical and experimental investigations have been performed to study the performances of the solar reactor. The experimental set-up and effect of operating conditions are described in this paper. In addition, simulation results are presented to interpret the experimental results and to improve the solar reactor concept. The temperature, geometry of the graphite nozzle, gas flow rates, and CH₄ mole fraction have a strong effect on the final chemical conversion of methane. Numerical simulations have shown that a simple tubular receiver is not enough efficient to heat the bulk gas in the central zone, thus limiting the chemical conversion. In that case, the reaction takes place only within a thin region located near the hot graphite wall. The maximum CH₄ conversion (98%) was obtained with an improved nozzle, which allows a more efficient gas heating due to its higher heat exchange area.     

Hydrogen production through partial oxidation of methane in a new reactor configuration

Performance of the side feeding (SF) air injection in the process of partial oxidation of methane (POM) has been investigated by means of developing a one-dimensional steady-state non-isothermal model. A fixed bed reactor (FBR), a one-side feeding reactor (One-SF), and a membrane reactor (MR) has been compared for the conversion of methane, selectivity of hydrogen and reactor temperature. The results of the model revealed that the One-SF can operate within FBR and MR, and increasing the number of air injections of SF could achieve to the performance of the MR. The performance of the two to five-SF was studied according to the hydrogen selectivity, methane conversion, temperature profile and H₂/CH₄ ratio. It was observed that increasing the number of injections up to the three, increased the selectivity of hydrogen from 0.496 to 0.530 and decreased the outlet temperature from 1269 K to 1078 K. These results lead to creating of a process with controllable operating temperature and enhancing the selectivity of hydrogen. Consequently, decreasing the problems of high operating temperature in FBR and reduction of the process cost compared with MR.     

Compartment model for steam reforming of methane in a membrane-assisted bubbling fluidized-bed reactor

A compartment model was developed to describe the flow pattern of gas within the dense zone of a membrane-assisted fluidized-bed reactor (MAFBR), in the bubbling mode of operation for steam reforming of methane both with (adiabatic) and without (isothermal) entering oxygen. Considering such a flow pattern and using the experimental data reported elsewhere [Roy S, Pruden BB, Adris AM, Grace JR, Lim CJ. Fluidized-bed steam methane reforming with oxygen input. Chem Eng Sci 1999; 54:2095–2102.], the parameters of the developed model (i.e., number of compartments for the bubble and emulsion phases) were determined and fair agreements were obtained between model predictions and experimental data. The developed model was utilized to describe the behavior of an industrial scale adiabatic and isothermal MAFBR. Moreover, the influences of various operating and design parameters such as steam-to-methane ratio (SMR), oxygen-to-methane ratio (OMR), operating temperature and pressure, and the number of hydrogen membrane tubes on the performance capability of the MAFBR were investigated. Furthermore, the performance capability of the MAFBR was optimized subject to the various operating and design constraints, including 1 ≤ SMR ≤ 4 and 500 ≤ T ≤ 1250 K, in the bubbling regime.     

The effect of non-uniform temperature on the sorption-enhanced steam methane reforming in a tubular fixed-bed reactor

The effect of non-uniform temperature on the sorption-enhanced steam methane reforming (SE-SMR) in a tubular fixed-bed reactor with a constant wall temperature of 600 °C is investigated numerically by an experimentally verified unsteady two-dimensional model. The reactor uses Ni/Al₂O₃ as the reforming catalyst and CaO as the sorbent. The reaction of SMR is enhanced by removing the CO₂ through the reaction of CaO + CO₂ → CaCO₃ based on the Le Chatelier's principle. A non-uniform temperature distribution instead of a uniform temperature in the reactor appears due to the rapid endothermic reaction of SMR followed by an exothermic reaction of CO₂ sorption. For a small weight hourly space velocity (WHSV) of 0.67 h^?1 before the CO₂ breakthrough, both a low and a high temperature regions exist simultaneously in the catalyst/sorbent bed, and their sizes are enlarged and the temperature distribution is more non-uniform for a larger tube diameter (D). Both the CH₄ conversion and the H₂ molar fraction are slightly increased with the increase of D. Based on the parameters adopted in this work, the CH₄ conversion, the H₂ and CO molar fractions at D = 60 mm are 84.6%, 94.4%, and 0.63%, respectively. After CO₂ breakthrough, the reaction of SMR dominates, and the reactor performance is remarkably reduced due to low reactor temperature.For a higher value of WHSV (4.03 h^?1) before CO₂ breakthrough, both the reaction times for SMR and CO₂ sorption become much shorter. The size of low temperature region becomes larger, and the high temperature region inside the catalyst/sorbent bed doesn't exist for D ≥ 30 mm. The maximum temperature difference inside the catalyst/sorbent bed is greater than 67 °C. Both the CH₄ conversion and H₂ molar fraction are slightly decreased with the increase of D. However, this phenomenon is qualitatively opposite to that for small WHSV of 0.67 h^?1. The CH₄ conversion and H₂ molar fraction at D = 60 mm are 52.6% and 78.7%, respectively, which are much lower than those for WHSV = 0.67 h^?1.     

Experimental and numerical analysis of a methane thermal decomposition reactor

An indirectly heated tubular reactor is fabricated and used to study methane thermal decomposition conversion and determine kinetic parameters. A combined perfectly mixed reactor with bypass (CPMR) is proposed as an alternative to the traditional perfectly mixed and plug flow reactors. The CPMR model is used in order to account for buoyancy flow in the reactor. Results comparing the numerical predictions from all three models to experimental data show that buoyancy effects are significant in the reactor under study and also in most reactors in the literature. Including this effect might significantly improve the accuracy of the model predictions. The CPMR reactor model with a reaction rate constant of 5.43 × 10¹⁵ 1/s and an activation energy of 420.7 kJ/mol is capable of reproducing the obtained experimental data in this study and in the literature.     

A pilot-scale solar reactor for the production of hydrogen and carbon black from methane splitting

A pilot-scale solar reactor was designed and operated at the 1 MW solar furnace of CNRS for H₂ and carbon black production from methane splitting. This constitutes the final objective of the SOLHYCARB EC project. The reaction of CH₄ dissociation produces H₂ and carbon nanoparticles without CO₂ emissions and with a solar upgrade of 8% of the high heating value of the products. The reactor was composed of 7 tubular reaction zones and of a graphite cavity-type solar receiver behaving as a black-body cavity. Temperature measurements around the cavity showed a homogeneous temperature distribution. The influence of temperature (1608K–1928K) and residence time (37–71 ms) on methane conversion, hydrogen yield, and carbon yield was especially stressed. For 900 g/h of CH₄ injected (50% molar, the rest being argon) at 1800K, this reactor produced 200 g/h H₂ (88% H₂ yield), 330 g/h CB (49% C yield) and 340 g/h C₂H₂ with a thermal efficiency of 15%. C₂H₂ was the most important by-product and its amount decreased by increasing the residence time. A 2D thermal model of the reactor was developed. It showed that the design of the reactor front face could be drastically improved to lower thermal losses. The optimised design could reach 77% of the ideal black-body absorption efficiency (86% at 1800K), i.e. 66%.     

Effect of radiation losses on very lean methane/air flames propagating upward in a vertical tube

The stationary upward propagation of a very lean methane/air flame in a long vertical tube open at the bottom and closed at the top is simulated numerically using a single overall chemical reaction to model combustion and assuming an optically thin gas and a transparent or non-reflecting tube wall to approximately account for radiation losses from CO₂${\text{CO}}_2$ and H₂O${\text{H}}_2\text{O}$. Buoyancy plays a dominant role in the propagation of these flames and causes a large region of low velocity of the burnt gas relative to the flame to appear below the flame front when the equivalence ratio is decreased. The size of this region scales with the radius of the tube, and its presence enhances the effect of radiation losses, which would be otherwise negligible for a standard flammability tube, given the small concentration of radiating species. Heat conduction is found to be important in the low velocity region and to lead to a conduction flux from the flame to the burnt gas that causes extinction at the flame tip for a value of the equivalence ratio near the flammability limit experimentally measured in the standard tube. The effect of radiation losses decreases with the radius of the tube. Numerical results and order-of-magnitude estimates show that, in the absence of radiation, a very lean flame front fails to propagate only after recirculation of the burnt gas extends to its reaction region and drastically changes its structure. This condition is not realized for the standard flammability tube, but it seems to account for the flammability limit measured in a tube of about half the radius of the standard tube.     

CFD simulation of methane steam reforming in a membrane reactor: Performance characteristics over range of operating window

Methane steam reforming is the most widely used pathway for hydrogen production. In this context, the use of a fixed bed catalytic reactor with a hydrogen-selective membrane is one of the most promising technologies to produce high purity hydrogen gas. In this work, the membrane reactor three-dimensional computational fluid dynamic (CFD) model was developed to investigate the performance. In this model, methane steam reforming global kinetic model has been coupled with the CFD model using User-Defined Function (UDF). Whereas, hydrogen permeation across the membrane is implemented by introducing source and sink formulation. The CFD simulation results were compared to the experimental data, where the developed model successfully captured the experimentally observed trends. We studied the influence of the various operating parameters, as temperature, steam to carbon ratio, sweep gas flow configuration and space velocity on the overall performance. The main observation and attained optimal operation windows from the study was discussed to provide insight into the factors affecting the overall performance.     

Hydrogen production from solar thermal dissociation of natural gas: development of a 10 kW solar chemical reactor prototype

This study addresses the solar thermal decomposition of natural gas for the co-production of hydrogen, as well as Carbon Black as a high-value nano-material, with the bonus of zero CO₂ emissions. The work focused on the development of a medium-scale solar reactor (10 kW) based on the concept of indirect heating. The solar reactor is composed of a cubic cavity receiver (20 cm side), which absorbs concentrated solar irradiation through a quartz window via a 9 cm-diameter aperture. The reacting gas flows inside four graphite tubular reaction zones that are settled vertically inside the cavity. Experimental results were as follows: methane conversion and hydrogen yield of up to 98% and 90%, respectively, were achieved at 1770 K, and acetylene was the most important by-product, with a mole fraction up to about 5%. The effect of the methane mole fraction in the feed gas, the residence time and the temperature on the reaction extent was analyzed. In addition to the experimental section, thermal simulations were carried out. They showed a homogeneous temperature distribution inside the cavity receiver of the reactor and permit to draw up a thermal balance.     

Experimental study on thermal efficiency and emission characteristics of a lean burn hydrogen enriched natural gas engine

In order to analyze the effect of hydrogen addition on natural gas (NG) engine's thermal efficiency and emission, an experimental research was conducted on a spark ignition NG engine using variable composition hydrogen/CNG mixtures (HCNG). The results showed that hydrogen enrichment could significantly extend the lean operation limit, improve the engine's lean burn ability, and decrease burn duration. However, nitrogen oxides (NO_x)$({\text{NO}}_x)$ were found to increase with hydrogen addition if spark timing was not optimized according to hydrogen's high burn speed. Also found when spark timing was set at constant was that hydrogen addition actually increases heat transfer out of the cylinder due to smaller quenching distance and higher combustion temperature, thus is not good to improve thermal efficiency if combined with the effect of non-ideal spark timing. But if spark timing was retarded to MBT, taking advantage of hydrogen's high burn speed, _NOx${\mathrm{NO}}_x$ emissions exhibited no obvious increase after hydrogen addition and engine thermal efficiency increased with the increase of hydrogen fraction. Unburned hydrocarbon always decreased with the increase of hydrogen fraction.     

Demonstration of a scaled-down autothermal membrane methane reformer for hydrogen generation

A novel concept for hydrogen generation by methane steam reforming in a thermally coupled catalytic fixed bed membrane reformer is experimentally demonstrated. The reactor, built from three concentric compartments, indirectly couples the endothermic methane steam reforming with the exothermic methane oxidation, while hydrogen is separated by a permselective Pd membrane. The study focuses on the determination of the key operation parameters and understanding their influence on the reactor performance. It has been shown that the reactor performance is mainly defined by the dimensionless ratio of the methane steam reforming feed flow rate to the hydrogen maximal membrane flow rate and by the ratio of the oxidation and steam reforming methane feed flow rates.     

Transient reaction phenomena of sorption-enhanced steam methane reforming in a fixed-bed reactor

The transient chemical reaction phenomena of the sorption-enhanced steam methane reforming (SE-SMR) by using Ni/Al₂O₃ catalyst and CaO sorbent in a tubular fixed-bed reactor were numerically investigated by an experimentally verified unsteady 2D model. Four chemical reactions are involved in SE-SMR including steam reforming (SR), water gas shift (WGS), global steam reforming (GSR), and CO₂ sorption. The reaction process in time is divided into period 1, transient period, and period 2. The high-purity H₂ is produced in period 1 which is defined as the outlet molar fractions of H₂ ≥ 90% and CO ≤ 1% (dry basis) in this work. In the first half of period 1, the endothermic reaction rates of SR and GSR are dominant in the entrance region of catalyst/sorbent bed. The WGS and CO₂ sorption reactions are triggered by SR and GSR reactions. The heat transfer from the wall plays an important role. Higher CaO conversion, temperature, and reaction rates appear first near the wall region, then they gradually expand to the central region.In the second half of period 1, a sharp wave-shaped curve of strong CO₂ sorption reaction occurred in downstream becomes dominant and it moves to downstream almost at a constant speed, as time progresses. The peak value of the CO₂ sorption reaction is more than twice larger than that of SR or WGS. The SR and WGS reaction rates are significantly enhanced by CO₂ sorption reaction. The great sorption, WGS, and SR reactions result in a high-purity H₂ production with the outlet molar fractions of 95.8% H₂, 0.998% CO, and 0.73% CO₂ at the end of period 1, based on the parameters used in this work such as reactor temperature of 600 °C. The maximum CaO conversion is about 76% in end of period 1 and the average CaO conversion in the reactor is 51%. The 2D distributions of CaO conversion, temperature, and reaction rates are also presented and discussed.     

Simulation of methane conversion to syngas in a membrane reactor. Part II: Model predictions

A one-dimensional non-isothermal model was employed in the simulation of partial oxidation of methane to syngas in a dense oxygen permeation membrane reactor. The model predicts that if methane is consumed completely in the reactor, a temperature runaway occurs. The reactor inlet temperature is chosen as a major factor to demonstrate the correlativity of the reactor performance and this phenomenon. A borderline inlet temperature (BIT) is defined. Simulation results showed that when the reactor inlet temperature approaches this value, an optimized reactor performance is achieved. This temperature increases with the increase of the air flow rate and carbon space velocity. The surface exchange kinetics at the oxygen-rich side has a small effect on this temperature, while that at the oxygen-lean side has a significant effect.     

Semi-continuous hydrogen production from catalytic methane decomposition using a fluidized-bed reactor

Non-oxidative, catalytic decomposition of hydrocarbons is an alternative, one-step process to produce pure hydrogen with no production of carbon oxides or higher hydrocarbons. Carbon produced from the decomposition reaction, in the form of potentially valuable carbon nanotubes, remains anchored to the active catalyst sites in a fixed bed. To facilitate periodical removal of this carbon from the reactor and to make hydrogen production continuous, a fluidized-bed reactor was envisioned. The hypothesis that the tumbling and inter-particle collisions of bed material would efficiently separate nanotubes anchored to the active catalyst sites of the bed particles was tested and shown to be invalid. However, a switching mode reaction system for the semi-continuous production of hydrogen and carbon nanotubes by periodic removal and replenishment of the catalytic bed material has been successfully demonstrated.     

Modeling and simulation of methane steam reforming in a thermally coupled membrane reactor

A distributed mathematical model for thermally coupled membrane reactor that is composed of three channels is developed for methane steam reforming. Methane combustion takes place in the first channel on a Pt/δ–Al₂O₃$\text{Pt}/\delta \text{–}{\text{Al}}_2{\text{O}}_3$ catalyst layer that supplies the necessary heat for the endothermic steam reforming reaction. In the second channel, catalytic steam reforming reactions take place in the presence of Ni/MgO–Al₂O₃ catalyst. The combustion catalyst forms a thin layer next to the reactor wall to minimize the heat transfer resistance. Selective permeation of hydrogen through the palladium membrane is achieved either by co-current or counter-current flow of sweep gas through the third channel. The burner is modeled as a monolith reactor and the reformer is assumed to behave as a pseudo-homogenous reactor. The mass and energy balance equations for the thermally coupled membrane reactor form a set of 22 coupled ordinary differential equations. With the application of appropriate boundary conditions, the distributed reactor model for steady-state operation is solved as a boundary value problem. The model equations are discretized using spline collocation on finite elements. The discretized nonlinear modeling equations, along with the boundary conditions, form a system of algebraic equations that are solved using the trust region dogleg method. The performance of the reactor is numerically investigated for various key operating variables such as inlet fuel concentration, inlet steam/methane ratio, inlet reformer gas temperature and inlet reformer gas velocity. Simulations for both the co-current and the countercurrent flow modes are also performed using different sweep gas flow rates. For each case, the reactor performance is analyzed based on methane conversion and hydrogen recovery yield.     

A thermochemical reactor design with better thermal management and improved performance for methane/carbon dioxide dry reforming

A solar thermochemical reactor with better thermal management is proposed to improve the performance for dry reforming of methane. Conical cavity is introduced in the thermochemical reactor to adjust incident solar radiation distribution. Preheating area is adopted to recover sensible heat from gas outlet. Multiphysical model is presented for analyzing the overall performance of the reactor under different inlet flow rates. Also, local ideal reaction temperature required for maximizing local hydrogen production is analyzed according to the reaction kinetics. It is shown that better synergy between real temperature distribution and ideal temperature requirement can be achieved in this new reactor. Compared with conventional reactor, the present reactor exhibits the better performance in terms of reactant conversion, energy storage efficiency and hydrogen yield. Particularly, hydrogen yield is increased by 4.31%–17.12% at inlet flow rates between 6 and 12 L min^?1.