Synthesis of BaFe12O19 by solid state method and its effect on hydrogen storage properties of MgH2

Previous studies have shown that ferrites give a positive effect in improving the hydrogen sorption properties of magnesium hydride (MgH₂). In this study, another ferrite, i.e., BaFe₁₂O₁₉, has been successfully synthesised via the solid state method, and it was milled with MgH₂ to enhance the sorption kinetics. The result showed that the MgH₂ + 10 wt% BaFe₁₂O₁₉ sample started to release hydrogen at about 270 °C which is about 70 °C lower than the as-milled MgH₂. The doped sample was able to absorb hydrogen for 4.3 wt% in 10 min at 150 °C, while as-milled MgH₂ only absorbed 3.5 wt% of hydrogen under similar conditions. The desorption kinetic results showed that the doped sample released about 3.5 wt% of hydrogen in 15 min at 320 °C, while the as-milled MgH₂ only released about 1.5 wt% of hydrogen. From the Kissinger plot, the apparent activation energy of the BaFe₁₂O₁₉-doped MgH₂ sample was 115 kJ/mol which was lower than the milled MgH₂ (141 kJ/mol)_. Further analyses demonstrated that MgO, Fe and Ba or Ba-containing contribute to the improvement by serving as active species, thus enhancing the MgH₂ for hydrogen storage.     

MnFe2O4 nanopowder synthesised via a simple hydrothermal method for promoting hydrogen sorption from MgH2

The effects of MnFe₂O₄ nanopowder synthesised via a simple ‘hydrothermal’ method on the hydrogen storage properties of MgH₂ are investigated for the first time. The particle size of the as-synthesised MnFe₂O₄ nanoparticles is determined to be about 10 nm. We observe that MnFe₂O₄ catalyst decreases the decomposition temperature of MgH₂ and enhances the sorption kinetics. Interestingly, the onset hydrogen desorption temperature of 10 wt% MnFe₂O₄-doped MgH₂ sample gets lowered from 350 °C to 240 °C with faster kinetics, and the sample shows an average dehydrogenation rate 8–9 times faster than that of the as-milled MgH₂ sample. By adding 10 wt% of as-prepared MnFe₂O₄ to MgH₂, approximately 5.5 wt% hydrogen can be absorbed in 10 min at 200 °C. In contrast, the un-doped MgH₂ sample absorbed only 4.0 wt% hydrogen in the same period of time. From the Kissinger analysis, the apparent activation energy for hydrogen released in the MnFe₂O₄-added MgH₂ composite is found to be 108.42 kJ/mol, which is much lower than the activation energy for hydrogen released in the as-milled MgH₂ (146.57 kJ/mol). It is believed that the in situ formed Fe particle and Mn-containing phases together play a synergistic role in remarkably improving MgH₂ storage properties.     

Kinetic improvement of H2 absorption and desorption properties in Mg/MgH2 by using niobium ethoxide as additive

The hydrogen absorption and desorption properties of a MgH₂ – 1 mol.% Nb(V) ethoxide mixture are reported. The material was prepared by hand mixing the additive with previously ball-milled MgH₂. Nb ethoxide reacts with MgH₂ during heating, releasing C₂H₆ and H₂, and producing MgO and Nb or Nb hydride. Hydriding and dehydriding are greatly enhanced by the use of the alkoxide. At 250 °C the material with Nb takes up 1.8 wt% in 30 s compared with 0.1 wt% of pure Mg, and releases 4.2 wt% in 30 min, whereas MgH₂ without Nb does not appreciably desorb hydrogen. The absorption and desorption activation energies are reduced from 153 kJ/mol H₂ to 94 kJ/mol H₂, and from 176 kJ/mol H₂ to 75 kJ/mol H₂, respectively. The hydrogen sorption properties remain stable after 10 cycles at 300 °C. The kinetic improvement is attributed to the fine distribution of amorphous/nanometric NbH_x achieved by the dispersion of the liquid additive.     

Graphene-anchored Ni6MnO8 nanoparticles with steady catalytic action to accelerate the hydrogen storage kinetics of MgH2

Transition metal-based oxides have been proven to have a substantial catalytic influence on boosting the hydrogen sorption performance of MgH₂. Herein, the catalytic action of Ni₆MnO₈@rGO nanocomposite in accelerating the hydrogen sorption properties of MgH₂ was investigated. The MgH₂ + 5 wt% Ni₆MnO₈@rGO composites began delivering H₂ at 218 °C, with about 2.7 wt%, 5.4 wt%, and 6.6 wt% H₂ released within 10 min at 265 °C, 275 °C, and 300 °C, respectively. For isothermal hydrogenation at 75 °C and 100 °C, the dehydrogenated MgH₂ + 5 wt% Ni₆MnO₈@rGO sample could absorb 1.0 wt% and 3.3 wt% H₂ in 30 min, respectively. Moreover, as compared to addition-free MgH₂, the de/rehydrogenation activation energies for doped MgH₂ composites were lowered to 115 ± 11 kJ/mol and 38 ± 7 kJ/mol, and remarkable cyclic stability was reported after 20 cycles. Microstructure analysis revealed that the in-situ formed Mg₂Ni/Mg₂NiH₄, Mn, MnO₂, and reduced graphene oxide synergically enhanced the hydrogen de/absorption properties of the Mg/MgH₂ system.     

Effects of KNbO3 catalyst on hydrogen sorption kinetics of MgH2

The influences of Nb-containing oxides and ternary compound in hydrogen sorption performance were investigated. As faster desorption kinetic and lower activation energy were reported by addition of a ternary compound catalyst such as K₂NiF₆, the influence of KNbO₃ on hydrogen storage properties of MgH₂ has been investigated for the first time. The MgH₂ - KNbO₃ composite desorbed 3.9 wt% of hydrogen within 10 min, while MgH₂ and MgH₂-Nb₂O₅ composites desorbed 0.66 wt% and 3.2 wt% respectively under similar condition. For MgH₂ with other Nb-contained catalysts such as Nb, NbO and Nb₂O₃, the desorption rate was almost the same as the one registered for as-milled MgH₂. The analysis of differential scanning calorimetry (DSC) showed that MgH₂-KNbO₃ composite started to release hydrogen at ∼335 °C which is 50 °C lower compared to as-milled MgH₂ without any additives. The activation energy for the hydrogen desorption was estimated to be about 104 ± 6.8 kJ mol⁻¹ for this material, while for the as-milled MgH₂ was about 165 ± 2.0 kJ mol⁻¹. It is believed that Nb-ternary oxide catalyst (KNbO₃) showed a good catalytic effect and enhance the sorption kinetics of MgH₂.     

Enhancing hydrogen storage performance of MgH2 through the addition of BaMnO3 synthesized via solid-state method

Currently, magnesium hydride (MgH₂) as a solid-state hydrogen storage material has become the subject of major research owing to its good reversibility, large hydrogen storage capacity (7.6 wt%) and affordability. However, MgH₂ has a high decomposition temperature (>400 °C) and slow desorption and absorption kinetics. In this work, BaMnO₃ was synthesized using the solid-state method and was used as an additive to overcome the drawbacks of MgH₂. Interestingly, after adding 10 wt% of BaMnO₃, the initial desorption temperature of MgH₂ decreased to 282 °C, which was 138 °C lower than that of pure MgH₂ and 61 °C lower than that of milled MgH₂. For absorption kinetics, at 250 °C in 2 min, 10 wt% of BaMnO₃-doped MgH₂ absorbed 5.22 wt% of H₂ compared to milled MgH₂ (3.48 wt%). Conversely, the desorption kinetics also demonstrated that 10 wt% of BaMnO₃-doped MgH₂ samples desorbed 5.36 wt% of H₂ at 300 °C within 1 h whereas milled MgH₂ only released less than 0.32 wt% of H₂. The activation energy was lowered by 45 kJ/mol compared to that of MgH₂ after the addition of 10 wt% of BaMnO₃. Further analyzed by using XRD revealed that the formation of Mg_0·9Mn_0·1O, Mn₃O₄ and Ba or Ba-containing enhanced the performance of MgH₂.     

Hydrogen absorption and desorption properties of Mg/MgH2 with nanometric dispersion of small amounts of Nb(V) ethoxide

A study to determine the optimal content of Nb(V) ethoxide required to efficiently catalyze the H₂ sorption kinetics in the Mg/MgH₂ system is reported. The materials were synthesized by hand mixing different amounts of additive (from 0.10 to 1 mol%) to pre-milled MgH₂. Considering kinetics and capacity the best performance corresponds to a 0.25 mol% of Nb ethoxide concentration. With this material, a remarkable kinetic behavior with excellent reversibility is obtained: 5.3 wt% and 5.1 wt% of hydrogen are absorbed and desorbed respectively at 300 °C in 3 min. At 250 °C the material absorbs 5.2 wt% of hydrogen and releases 3.7 wt% in 10 min. Thermal desorption starts at 247 °C and peaks at 268 °C. The H₂ sorption properties of all the materials remain unchanged after 10 cycles of absorption and desorption at 300 °C, and the best material reversibly takes in and releases 5.3 wt% of H₂ during a 10 min combined cycle. The kinetic improvement of the hydrogen desorption and absorption properties is attributed to an enhancement of the kinetic processes that occur on the surface of the material, due to the excellent spreading of the liquid additive at nanometric level, as revealed by SEM/EDS and TEM/EELS.     

Remarkable kinetics of novel Ni@CeO2–MgH2 hydrogen storage composite

Magnesium hydroxide (MgH₂) has excellent reversibility and high capacity, and is one of the most promising materials for hydrogen storage in practical applications. However, it suffers from high dehydrogenation temperature and slow sorption kinetics. Rare earth hydrides and transition metals can both significantly improve the de/hydrogenation kinetics of MgH₂. In this work, MgH₂–Mg₂NiH₄–CeH_2.73 is in-situ synthesized by introducing Ni@CeO₂ into MgH₂. The unique coating structure of Ni@CeO₂ facilitates homogeneous distribution of synergetic CeH_2.73 and Mg₂NiH₄ catalytic sites in subsequent ball milling process. The as-fabricated composite MgH₂-10 wt% Ni@CeO₂ powders possess superior hydrogenation/dehydrogenation characteristics, absorbing 4.1 wt% hydrogen within 60 min at 100 °C and releasing 5.44 wt% H₂ within 10 min at 350 °C. The apparent activation energy of MgH₂-10 wt% Ni@CeO₂ is determined to be 84.8 kJ/mol and it has favorable hydrogen cycling stability with almost no decay in capacity after 10 cycles.     

Ternary transition metal alloy FeCoNi nanoparticles on graphene as new catalyst for hydrogen sorption in MgH2

The present investigation deals with the synthesis of ternary transition metal alloy nanoparticles of FeCoNi and graphene templated FeCoNi (FeCoNi@GS) by one-pot reflux method and there use as a catalyst for hydrogen sorption in MgH₂. It has been found that the MgH₂ catalyzed by FeCoNi@GS (MgH₂: FeCoNi@GS) has the onset desorption temperature of ~255 °C which is 25 °C and 100 °C lower than MgH₂ catalyzed by FeCoNi (MgH₂: FeCoNi) (onset desorption temperature 280 °C) and the ball-milled (B.M) MgH₂ (onset desorption temperature 355 °C) respectively. Also MgH₂: FeCoNi@GS shows enhanced kinetics by absorbing 6.01 wt% within just 1.65 min at 290 °C under 15 atm of hydrogen pressure. This is much-improved sorption as compared to MgH₂: FeCoNi and B.M MgH₂ for which hydrogen absorption is 4.41 wt% and 1.45 wt% respectively, under the similar condition of temperature, pressure and time. More importantly, the formation enthalpy of MgH₂: FeCoNi@GS is 58.86 kJ/mol which is 19.26 kJ/mol lower than B.M: MgH₂ (78.12 kJ/mol). Excellent cyclic stability has also been found for MgH₂: FeCoNi@GS even up to 24 cycles where it shows only negligible change from 6.26 wt% to 6.24 wt%. A feasible catalytic mechanism of FeCoNi@GS on MgH₂ has been put forward based on X-ray diffraction (XRD), Raman spectroscopy, Fourier Transform Infrared Spectroscopy (FTIR), X-Ray Photoelectron Spectroscopy (XPS), and microstructural (electron microscopic) studies.     

Improvement of hydrogen storage properties in MgH2 catalysed by K2NbF7

The catalytic effects of K₂NbF₇ on the hydrogen storage properties of MgH₂ have been studied for the first time. MgH₂ + 5 wt% K₂NbF₇ has reduced the onset dehydrogenation temperature to 255 °C, which is 75 °C lower than the as-milled MgH₂. For the rehydrogenation kinetic, at 150 °C, MgH₂ + 5 wt% K₂NbF₇ absorbs 4.7 wt% of hydrogen in 30 min whereas the as-milled MgH₂ only absorbs 0.7 wt% of hydrogen under similar condition. For the dehydrogenation kinetic, at 320 °C, the MgH₂ + 5 wt% K₂NbF₇ is able to release 5.2 wt% of hydrogen in 5.6 min as compared to 0.3 wt% by the as-milled MgH₂ under similar condition. Comparatively, the E_a value of MgH₂ + 5 wt% K₂NbF₇ is 96.3 kJ/mol, which is 39 kJ/mol lower compared to the as-milled MgH₂. The MgF₂, the KH and the Nb that are found after the heating process are believed to be the active species that have improved the system properties. It is concluded that the K₂NbF₇ is a good catalyst to improve the hydrogen storage properties of MgH₂.     

CoFe2O4 synthesized via a solvothermal method for improved dehydrogenation of NaAlH4

The effect of cobalt ferrite (CoFe₂O₄) nanopowder synthesised through a solvothermal method on the dehydrogenation properties of sodium alanate (NaAlH₄) was studied for the first time. The onset decomposition temperature of NaAlH₄ is significantly reduced after milling with CoFe₂O₄, in which the 10 wt% CoFe₂O₄-doped NaAlH₄ sample starts to decompose at ～100 °C. In contrast, the as-milled NaAlH₄ begins to decompose at ～200 °C, ～100 °C higher than the doped sample. With respect to desorption kinetic at constant temperature of 150 °C, the 10 wt% CoFe₂O₄-doped NaAlH₄ sample desorbed ～2.2 wt% hydrogen within 30 min, whereas the as-milled NaAlH₄ only desorbed below 0.2 wt% hydrogen. The Kissinger plot exhibited that the apparent activation energy (E_A) for hydrogen release from NaAlH₄ is significantly reduced after adding with 10 wt% CoFe₂O₄-doped NaAlH₄. The E_A values for the first and second stage dehydrogenation of the 10 wt% CoFe₂O₄-doped NaAlH₄ composite are calculated as 80.3 and 88.2 kJ/mol, respectively, and these values are reduced at approximately 34.3 and 30.5 kJ/mol compared with the as-milled NaAlH₄ (114.6 and 118.7 kJ/mol, respectively). Based on the X-ray diffraction result, the enhancement of desorption properties of NaAlH₄ with the presence of CoFe₂O₄ is presumably due to the synergistic catalytic effect played by new active species (Co₃O₄ and Fe) that in situ formed during the desorption process.     

Synthesis of low-cost biomass charcoal-based Ni nanocatalyst and evaluation of their kinetic enhancement of MgH2

In this study, a low-cost biomass charcoal (BC)-based nickel catalyst (Ni/BC) was introduced into the MgH₂ system by ball-milling. The study demonstrated that the Ni/BC catalyst significantly improved the hydrogen desorption and absorption kinetics of MgH₂. The MgH₂ + 10 wt% Ni/BC-3 composite starts to release hydrogen at 187.8 °C, which is 162.2 °C lower than the initial dehydrogenation temperature of pure MgH₂. Besides, 6.04 wt% dehydrogenation can be achieved within 3.5 min at 300 °C. After the dehydrogenation is completed, MgH₂ + 10 wt% Ni/BC-3 can start to absorb hydrogen even at 30 °C, which achieved the absorption of 5 wt% H₂ in 60 min under the condition of 3 MPa hydrogen pressure and 125 °C. The apparent activation energies of dehydrogenation and hydrogen absorption of MgH₂ + 10 wt% Ni/BC-3 composites were 82.49 kJ/mol and 23.87 kJ/mol lower than those of pure MgH₂, respectively, which indicated that the carbon layer wrapped around MgH₂ effectively improved the cycle stability of hydrogen storage materials. Moreover, MgH₂ + 10 wt% Ni/BC-3 can still maintain 99% hydrogen storage capacity after 20 cycles. XRD, EDS, SEM and TEM revealed that the Ni/BC catalyst evenly distributed around MgH₂ formed Mg₂Ni/Mg₂NiH₄ in situ, which act as a “hydrogen pump” to boost the diffusion of hydrogen along with the Mg/MgH₂ interface. Meanwhile, the carbon layer with fantastic conductivity enormously accelerated the electron transfer. Consequently, there is no denying that the synergistic effect extremely facilitated the hydrogen absorption and desorption kinetic performance of MgH₂.     

Interfacial engineering of nickel/vanadium based two-dimensional layered double hydroxide for solid-state hydrogen storage in MgH2

As a high-density solid-state hydrogen storage material, magnesium hydride (MgH₂) is promising for hydrogen transportation and storage. Yet, its stable thermodynamics and sluggish kinetics are unfavorable for that required for commercial application. Herein, nickel/vanadium trioxide (Ni/V₂O₃) nanoparticles with heterostructures were successfully prepared via hydrogenating the NiV-based two-dimensional layered double hydroxide (NiV-LDH). MgH₂ + 7 wt% Ni/V₂O₃ presented more superior hydrogen absorption and desorption performances than pure MgH₂ and MgH₂ + 7 wt% NiV-LDH. The initial discharging temperature of MgH₂ was significantly reduced to 190 °C after adding 7 wt% Ni/V₂O₃, which was 22 and 128 °C lower than that of 7 wt% NiV-LDH modified MgH₂ and additive-free MgH₂, respectively. The completely dehydrogenated MgH₂ + 7 wt% Ni/V₂O₃ charged 5.25 wt% H₂ in 20 min at 125 °C, while the hydrogen absorption capacity of pure MgH₂ only amounted to 4.82 wt% H₂ at a higher temperature of 200 °C for a longer time of 60 min. Moreover, compared with MgH₂ + 7 wt% NiV-LDH, MgH₂ + 7 wt% Ni/V₂O₃ shows better cycling performance. The microstructure analysis indicated the heterostructural Ni/V₂O₃ nanoparticles were uniformly distributed. Mg₂Ni/Mg₂NiH₄ and metallic V were formed in-situ during cycling, which synergistically tuned the hydrogen storage process in MgH₂. Our work presents a facile interfacial engineering method to enhance the catalytic activity by constructing a heterostructure, which may provide the mentality of designing efficient catalysts for hydrogen storage.     

Synergistic enhancement of hydrogen storage properties in MgH2 using LiNbO3 catalyst

Extensive researches are being conducted to improve the high dehydrogenation temperature and sluggish hydrogen release rate of magnesium hydride (MgH₂) for better industrial application. In this study, LiNbO₃, a catalyst composed of alkali metal Li and transition metal Nb, was prepared through a direct one-step hydrothermal synthesis, which remarkably improved the hydrogen storage performance of MgH₂. With the addition of 6 wt% LiNbO₃ in MgH₂, the initial dehydrogenation temperature decreases from 300 °C to 228 °C, representing a drop of almost 72 °C compared to milled MgH₂. Additionally, the MgH₂-6 wt.% LiNbO₃ composite can quickly release 5.45 wt% of H₂ within 13 min at 250 °C, and absorbed about 3.5 wt% of H₂ within 30 min at 100 °C. It is also note that LiNbO₃ shows better catalytic effect compared to solely adding Li₂O or Nb₂O₅. Furthermore, the activation energy of MgH₂-6 wt.% LiNbO₃ decreased by 44.37% compared to milled MgH₂. The enhanced hydrogen storage performance of MgH₂ is attributed to the in situ formation of Nb-based oxides in the presence of LiNbO₃, which creates a multielement and multivalent chemical environment.     

CNTs decorated with CoFeB as a dopant to remarkably improve the dehydrogenation/rehydrogenation performance and cyclic stability of MgH2

The chain-like carbon nanotubes (CNTs) decorated with CoFeB (CoFeB/CNTs) prepared by oxidation-reduction method is introduced into MgH₂ to facilitate its hydrogen storage performance. The addition of CoFeB/CNTs enables MgH₂ to start desorbing hydrogen at only 177 °C. Whereas pure MgH₂ starts hydrogen desorption at 310 °C. The dehydrogenation apparent activation energy of MgH₂ in CoFeB/CNTs doped-MgH₂ composite is only 83.2 kJ/mol, and this is about 59.5 kJ/mol lower than that of pure MgH₂. In addition, the completely dehydrogenated MgH₂−10 wt% CoFeB/CNTs sample can start to absorb hydrogen at only 30 °C. At 150 °C and 5 MPa H₂, the MgH₂ in CoFeB/CNTs doped-MgH₂ composite can absorb 6.2 wt% H₂ in 10 min. The cycling kinetics can remain rather stable up to 20 cycles, and the hydrogen storage capacity retention rate is 98.5%. The in situ formation of Co₃MgC, Fe, CoFe and B caused by the introduction of CoFeB/CNTs can provide active and nucleation sites for the dehydrogenation/rehydrogenation reactions of MgH₂. Moreover, CNTs can provide hydrogen diffusion pathways while also enhancing the thermal conductivity of the sample. All of these can facilitate the dehydrogenation/rehydrogenation performance and cyclic stability of MgH₂.     

Enhanced hydrogen sorption properties of MgH2 when doped with mechanically alloyed amorphous Zr0·67Ni0.33 particles

In the present study, the effect of amorphous Zr_0·67Ni_0.33 additive containing nano-ZrO₂ on the hydrogen sorption kinetics and thermodynamics of Mg/MgH₂ was investigated. The amorphous Zr_0·67Ni_0.33 particles prepared by mechanical alloying of stoichiometric elements were introduced into MgH₂ powder through high-energy milling to produce a MgH₂/Zr_0·67Ni_0.33 composite. Structural and morphological analyses revealed that the nanostructuring effect of the ZrO₂ containing amorphous Zr_0·67Ni_0.33 has led to significant grain-size refinement of MgH₂ to the nanometric scale. As a result, the MgH₂/Zr_0·67Ni_0.33 composite demonstrates enhanced hydrogenation and dehydrogenation kinetics (4.0 wt%/50 s/250 °C and 5.0 wt%/4 min/325 °C, respectively). Meantime, substantially lowered enthalpies (−63.40 and 67.06 kJ/mol H₂ obtained through pressure-composition-isotherm measurements) and reduced desorption temperature (~270 °C) were observed in the composite as compared to the pure MgH₂, possibly due to the dissolution of Ni into MgH₂ lattice during ball milling.     

Enhanced hydrogen absorption and desorption properties of MgH2 with graphene and vanadium disulfide

Magnesium hydride (MgH₂) is the most prominent carrier for storing hydrogen in solid-state mode. However, their slow kinetics and high thermodynamics become an obstacle in hydrogen storage. The present study elaborates on the catalytic effect of graphene (Gr) and vanadium disulfide (VS₂) on MgH₂ to enhance its hydrogen sorption kinetic. The temperature-programmed desorption study shows that the onset desorption temperature of MgH₂ catalyzed by VS₂ and MgH₂ catalyzed by Gr is 289 °C and 300 °C, respectively. These desorption temperatures are 87 °C and 76 °C lower than the desorption temperature of pristine MgH₂. The rapid rehydrogenation kinetics for the MgH₂ catalyzed by VS₂ have been found at a temperature of 300 °C under 15 atm H₂ pressure by absorbing ∼4.04 wt% of hydrogen within 1 min, whereas the MgH₂ catalyzed by Gr takes ∼3 min for absorbing the same amount of hydrogen under the similar temperature and pressure conditions. The faster release of hydrogen was also observed in MgH₂ catalyzed by VS₂ than MgH₂ catalyzed by Gr and pristine MgH₂. MgH₂ catalyzed by VS₂ releases ∼2.54 wt% of hydrogen within 10 min, while MgH₂ catalyzed by Gr takes ∼30 min to release the same amount of hydrogen. Furthermore, MgH₂ catalyzed by VS₂ also persists in the excellent cyclic stability and reversibility up to 25 cycles.     

Synthesis of MgH2 using autocatalytic effect of MgH2

We describe the synthesis of MgH₂ using autocatalytic effect of MgH₂. The MgH₂ was synthesized by ball milling Mg with 5 wt% of MgH₂. The ball milling was carried out at different pressures of 15, 30 and 45 atm of H₂ followed by heat treatment (heating under vacuum and annealing at 30 atm of H₂ pressure (at 350 °C) for 10 h). It has been found that the MgH₂ synthesized using 30 atm of H₂ pressure during ball milling, followed by heat treatment and annealing (MgH₂30BM) is the optimum material as it has lowest desorption temperature (325 °C) faster rehydrogenation kinetic (6.60 wt% within 30 min at 300 °C and 20 atm hydrogen pressure). Also MgH₂30BM maintains the storage capacity of more than 6.00 wt% (loss of 0.6 wt%) after 10 cycles of de/re-hydrogenation. The as synthesized MgH₂ has superior de/re-hydrogenation properties and is ∼4 times cheaper as compared to MgH₂ procured from the chemical company like Alfa-Aesar. It is to be mentioned that under above mentioned temperature and pressure conditions the stand alone Mg (without having MgH₂ as catalyst) doesnot at all converts to MgH₂. The present study opens the gateway for economical synthesis of MgH₂ at large scale.     

Catalytic mechanism of TiO2 quantum dots on the de/re-hydrogenation characteristics of magnesium hydride

In the present study, the catalyst anatase titanium dioxide (TiO₂) quantum dots (QDs) of size ∼ (2.50–4.00)nm was successfully synthesized by the hydrothermal method. The formation of TiO₂: QDs has been established by UV–Vis spectroscopy and confirmed by transmission electron microscopy. Here, we report the catalytic action of TiO₂:QDs on de/re-hydrogenation properties of magnesium hydride (MgH₂/Mg). By catalyzing MgH₂ through this catalyst, the onset desorption temperature of MgH₂ gets reduced significantly from ∼360 °C (for ball-milled MgH₂) to ∼260 °C. Moreover, the Mg-TiO₂: QDs sample absorbed a significant amount of hydrogen up to ∼6.10 wt% in just 77sec at 280 °C. Improved rehydrogenation kinetics has been found even at lower temperatures by absorbing ∼5.30 wt% in 74 s at 225 °C and ∼5.0 wt% of hydrogen in 30 min at 100 °C. Based on structural,.microstructural, and XPS investigations, a feasible mechanism for improved hydrogen sorption and cyclic stability in MgH₂ catalyzed with TiO₂:QDs has been explained and discussed. To our knowledge, no studies have been carried out on the sorption of hydrogen in MgH₂ catalyzed by TiO₂:QDs.     

Integrated Ni/Nb2O5 nanocatalytic agent dose for improving the hydrogenation/dehydrogenation kinetics of reacted ball milled MgH2 powders

Reactive ball milling (RBM) technique was employed to synthesize ultrafine powders of MgH₂, using high energy ball mill operated at room temperature under 50 bar of a hydrogen gas atmosphere. The MgH₂ powders obtained after 200 h of continuous RBM time composed of β and γ phases. The powders possessed nanocrystalline characteristics with an average grain of about 10 nm in diameter. The time required for complete hydrogen absorption and desorption measured at 250 °C was 500 s and 2500 s, respectively. In order to improve the hydrogenation/dehydrogenation kinetics of as synthesized MgH₂ powders, three different types of nanocatalysts (metallic Ni, Nb₂O₅ and (Ni)_x/(Nb₂O₅)_y) were utilized with different weight percentages and independently ball milled with the MgH₂ powders for 50 h under 50 bar of a hydrogen gas atmosphere. The results showed that the prepared nanocomposite MgH₂/5Ni/5Nb₂O₅ powders possessed superior hydrogenation/dehydrogenation characteristics, indexed by low values of activation energy for β-phase (68 kJ/mol) and γ-phase (74 kJ/mol). This nanocomposite system showed excellent hydrogenation/dehydrogenization behavior, indexed by the short time required to uptake (41 s) and release (121 s) of 5 wt% H₂ at 250 °C. At this temperature the synthesized nanocomposite powders possessed excellent absorption/desorption cyclability of 180 complete cycles. No serious degradation on the hydrogen storage capacity could be detected and the system exhibited nearly constant absorption and desorption values of +5.46 and −5.46 wt% H₂, respectively.