Study of the synthesis of PMMA-Mg nanocomposite for hydrogen storage application

The nano metallic-based material has received the particular attention of scientists in H₂ storage. Herein, an efficient air-stable nano metallic magnesium (Mg)-Polymethyl methacrylate (PMMA) system, in which methyl magnesium chloride (MeMgCl) as organic Mg precursor is in-situ reduced to metallic Mg particles (Mg NPs) by lithium naphthalene (Li-naphthalene) in soluble PMMA/THF system, exhibits an excellent H₂ storage performance and do not require harsh operation condition. In order to form well-distributed Mg NPs (co. 5 nm) in PMMA gel framework, it is an important procedure to mix Mg ion and Li-naphthalene completely, as well the restriction effect of polymer molecular chain. The synthesized mechanism of nanocomposite and the optimal reaction conditions were ascertained by designing a series of experiments. Notably, PMMA can not confined the size of metallic Mg by blending method, and the mixed β/γ-Mg presents nearly no ability to adsorb hydrogen. Here, the air stable Mg NPs is in-situ reduced in PMMA can be reacted with H₂, and O₂ and H₂O molecules can not be infiltrated into PMMA. The correlation between the size of Mg NPs, the amount of PMMA and hydrogen storage performance for the PMMA-Mg NPs composite (PMC) is studied. We have found that hydrogen storage capacity of PMC could be enhanced as decreasing the size of Mg NPs by adjusting the amount of PMMA. The Mg NPs in PMMA might release the higher amount of H₂ at below 300 °C with a rapid absorption/desorption kinetics than the reported material in literature. The obtained nanocomposite are able to deliver dense hydrogen in demanding environments.     

Synthetical catalysis of nickel and graphene on enhanced hydrogen storage properties of magnesium

Reduced graphene-oxide-supported nickel (Ni@rGO) nanocomposite catalysts were synthesized, and incorporated into magnesium (Mg) hydrogen storage materials with the aim of improving the hydrogen storage properties of these materials. The experimental results revealed that the catalytic effect of the Ni@rGO nanocomposite on Mg was more effective than that of single nickel (Ni) nanoparticles or graphene. When heated at 100 °C, the Mg–Ni and Mg–Ni@rGO composites absorbed 4.70 wt% and 5.48 wt% of H₂, respectively, whereas the pure Mg and Mg@rGO composite absorbed almost no hydrogen. The addition of the Ni@rGO composite as a catalyst yielded significant improvement in the hydrogen storage property of the Mg hydrogen storage materials. The apparent activation energy of the pure Mg sample (i.e., 163.9 kJ mol⁻¹) decreased to 139.7 kJ mol⁻¹ and 123.4 kJ mol⁻¹, respectively, when the sample was modified with single rGO or Ni nanoparticles. Under the catalytic action of the Ni@rGO nanocomposites, the value decreased further to 103.5 kJ mol⁻¹. The excellent hydrogen storage properties of the Mg–Ni@rGO composite were attributed to the catalytic effects of the highly surface-active Ni nanoparticles and the unique structure of the composite nanosheets.     

Metal organic framework derived nitrogen-doped carbon anchored palladium nanoparticles for ambient temperature formic acid decomposition

Well-dispersed palladium nanoparticles (NPs) anchored on a porous N-doped carbon is prepared by wet chemical method, using metal organic frameworks (ZIF-8) as a precursor to derive the porous N-doped carbon support. Benefitting from the N-doping and the porous structure of the carbon materials, the final Pd NPs are in high dispersion and exhibit reduced particle sizes, with electronic structure and chemical status tuned to favor the formic acid decomposition (FAD). The prepared Pd/C_ZIF-8-950 catalysts show enhanced catalytic performance and selectivity for FAD, the turnover of frequency (TOF) and the mass activity up to 1166 h⁻¹ and 11.01 mol H₂ g⁻¹ _pd h⁻¹ were obtained at 30 °C. This work provides an effective and easy way for synthesis the Pd-based catalyst, which has enormous application prospects for the next generation hydrogen energy preparation and storage.     

Study on catalytic effect and mechanism of MOF (MOF = ZIF-8, ZIF-67, MOF-74) on hydrogen storage properties of magnesium

Using a deposition-reduction method, Mg/MOF nanocomposites were prepared as composites of Mg and metal-organic framework materials (MOFs = ZIF-8, ZIF-67 and MOF-74). The addition of MOFs can enhance the hydrogen storage properties of Mg. For example, within 5000 s, 0.6 wt%, 1.2 wt%, 2.7 wt%, 3.7 wt% of hydrogen were released from Mg, Mg/MOF-74, Mg/ZIF-8, Mg/ZIF-67, respectively. Activation energy values of 198.9 kJ mol⁻¹ H₂, 161.7 kJ mol⁻¹ H₂, 192.1 kJ mol⁻¹ H₂ were determined for the Mg/ZIF-8, Mg/ZIF-67, Mg/MOF-74 hydrides, which are 6 kJ mol⁻¹ H₂, 43.2 kJ mol⁻¹ H₂, and 12.8 kJ mol⁻¹ H₂ lower than that of Mg hydride, respectively. Moreover, the cyclic stability characterizing Mg hydride was significantly improved when adding ZIF-67. The hydrogen storage capacity of the Mg/ZIF-67 nanocomposite remained unchanged, even after 100 cycles of hydrogenation/dehydrogenation. This excellent cyclic stability may have resulted from the core-shell structure of the Mg/ZIF-67 nanocomposite.     

Size and stress dependent hydrogen desorption in metastable Mg hydride films

Mg is a promising light-weight material that has superior hydrogen storage capacity. However H₂ storage in Mg typically requires high temperature, ∼500–600 K. Furthermore it has been shown that there is a peculiar film thickness effect on H₂ sorption in Mg films, that is thinner Mg films desorb H₂ at higher temperature [1]. In this study we show that the morphology of DC magnetron sputtered Mg thin films on rigid SiO₂ substrate varied from a continuous dense morphology to porous columnar structure when they grew thicker. Sputtered Mg films absorbed H₂ at 373 K and evolved into a metastable orthorhombic Mg hydride phase. Thermal desorption spectroscopy studies show that thinner dense MgH₂ films desorb H₂ at lower temperature than thicker porous MgH₂ films. Meanwhile MgH₂ pillars with greater porosity have degraded hydrogen sorption performance contradictory to general wisdom. The influences of stress on formation of metastable MgH₂ phase and consequent reduction of H₂ sorption temperature are discussed.     

Different effects of temperature on supramolecular protein and non-protein materials in hydrogen storage

The storage of large quantities of hydrogen at ambient temperature is a key factor in establishing a hydrogen-based economy. One strategy for hydrogen storage is to exploit the interaction between H₂ and a solid material by physisorption of hydrogen on porous materials. However, physisorption materials containing MOF, porous carbons, zeolites, clathrates, and synthesized organic polymers physisorb only about 1 wt% of H₂ at ambient temperature. One approach to solving this problem is to prepare new classes of physisorption materials which exhibits a mechanism different from the reported materials in hydrogen storage. Here we report the synthesis of apo cross-linked ferritin supramolecules by disulfide bonds, and their holo form. Unlike non-protein adsorbents, the hydrogen storage capacity of these protein materials increases as a function of temperature over the range of 20–40 °C. The holo supramolecules enable the adsorption of hydrogen up to 3.51 wt% at 40 °C and 40 bar H₂. In contrast, non-protein physisorption materials such as activated carbon and nano Fe₂O₃ marginally adsorb hydrogen, and, as reported, their ability to adsorb hydrogen decreases with increasing temperature under the same experimental condition. These results demonstrate that protein materials have a unique hydrogen storage mechanism which offers new opportunities in exploration of physisorption materials at ambient temperature.     

Electrochemical hydrogen storage behavior of Ni-Ceria impregnated carbon micro-nanofibers

A hierarchical porous structured carbon micro-nanofiber containing the bimetallic configuration of the nickel (Ni) and ceria (CeO₂) nanoparticles (NPs) was synthesized and tested for the electrochemical hydrogen (H₂) storage capacity. The electrode exhibited a high H₂ storage capacity of 498 mA h/g or 1.858% (w/w) at the charge-discharge current density of 500 mA/g. A mechanistic insight showcased the combined contributions of the high surface area containing activated carbon microfiber (ACF) substrate, the graphitic carbon nanofibers (CNFs), and the Ni and CeO₂ NPs, towards the augmented electrochemical H₂ storage capacity and cyclic stability of the fabricated Ni–CeO₂–CNF/ACF electrode. Ni served as the catalyst for growing the CNFs via chemical vapor deposition as well as for storing H₂ via spillover mechanism, while CeO₂ created the charge carrier vacancies in the material. The measured cycle retention capacity of 99% and charge-discharge efficiency of 97.6% confirm the electrochemically stable characteristics of Ni–CeO₂–CNF/ACF, and clearly indicate it to be an economically viable and efficient H₂-storage material.     

Enhancing hydrogen storage properties of the Mg/MgH2 system by the addition of bis(tricyclohexylphosphine)nickel(II) dichloride

This is a first report on the use of the bis(tricyclohexylphosphine)nickel (II) dichloride complex (abbreviated as NiPCy3) into MgH₂ based hydrogen storage systems. Different composites were prepared by planetary ball-milling by doping MgH₂ with (i) free tricyclohexylphosphine (PCy3) without or with nickel nanoparticles, (ii) different NiPCy3 contents (5–20 wt%) and (iii) nickel and iron nanoparticles with/without NiPCy3. The microstructural characterization of these composites before/after dehydrogenation was performed by TGA, XRD, NMR and SEM-EDX. Their hydrogen absorption/desorption kinetics were measured by TPD, DSC and PCT. All MgH₂ composites showed much better dehydrogenation properties than the pure ball-milled MgH₂. The hydrogen absorption/release kinetics of the Mg/MgH₂ system were significantly enhanced by doping with only 5 wt% of NiPCy3 (0.42 wt% Ni); the mixture desorbed H₂ starting at 220 °C and absorbed 6.2 wt% of H₂ in 5 min at 200 °C under 30 bars of hydrogen. This remarkable storage performance was not preserved upon cycling due to the complex decomposition during the dehydrogenation process. The hydrogen storage properties of NiPCy3-MgH₂ were improved and stabilized by the addition of Ni and Fe nanoparticles. The formed system released hydrogen at temperatures below 200 °C, absorbed 4 wt% of H₂ in less than 5 min at 100 °C, and presented good reversible hydriding/dehydriding cycles. A study of the different storage systems leads to the conclusion that the NiPCy3 complex acts by restricting the crystal size growth of Mg/MgH₂, catalyzing the H₂ release, and homogeneously dispersing nickel over the Mg/MgH₂ surface.     

Transition metal nanoparticle catalysts in releasing hydrogen from the methanolysis of ammonia borane

Ammonia borane (H₃N·BH₃, AB) is one of the promising hydrogen storage materials due to high hydrogen storage capacity (19.6% wt), high stability in solid state as well as in solution and nontoxicity. The methanolysis of AB is an alternative way of releasing H₂ due to many advantages over the hydrolysis such as having high stability against self releasing hydrogen gas. Here we review the reports on using various noble or non-noble metal(0) catalysts for H₂ release from the methanolysis of AB. Ni(0), Pd(0), and Ru(0) nanoparticles (NPs), stabilized as colloidal dispersion in methanol, are highly active and long lived catalysts in the methanolysis of AB. The catalytic activity, lifetime and reusability of transition metal(0) NPs show significant improvement when supported on the surface of solid materials. The supported cobalt, nickel, copper, palladium, and ruthenium based catalysts are quite active in H₂ release from the methanolysis of AB. Rh(0) NPs are highly active catalysts in releasing H₂ from the methanolysis of AB when confined within the void spaces of zeolite or supported on oxide nanopowders such as nanosilica, nanohydroxyapatite, nanoalumina or nanoceria. The oxide supported Rh(0) NPs can provide high activity with turnover frequency values as high as 218 min⁻¹ and long lifetime with total turnover values up to 26,000 in generation of H₂ from the methanolysis of AB at 25 °C. When deposited on carbon the bimetallic AgPd alloy nanoparticles have the highest activity in releasing H₂ through the methanolysis of AB.     

Hydrogen adsorption properties of in-situ synthesized Pt-decorated porous carbons templated from zeolite EMC-2

To increase the interaction between the adsorbed hydrogen and the adsorbent surface to improve the hydrogen storage capacity at ambient temperature, decorating the sorbents with metal nanoparticles, such as Pd, Ni, and Pt has attracted the most attention. In this work, Pt-decorated porous carbons were in-situ synthesized via CVD method using Pt-impregnated zeolite EMC-2 as template and their hydrogen uptake performance up to 20 bar at 77, 87, 298 and 308 K has been investigated with focus on the interaction between the adsorbed H₂ and the carbon matrix. It is found that the in-situ generated Pt-decorated porous carbons exhibit Pt nanoparticles with size of 2–4 nm homogenously dispersed in the porous carbon, accompanied with observable carbon nanowires on the surface. The calculated H₂ adsorption heats at/near 77 K are similar for both the plain carbon (7.8 kJ mol⁻¹) and the Pt-decorated carbon (8.3 kJ mol⁻¹) at H₂ coverage of 0.08 wt.%, suggesting physisorption is dominated in both cases. However, the calculated H₂ adsorption heat at/near 298 K of Pt-decorated carbon is 72 kJ mol⁻¹ at initial H₂ coverage (close to 0), which decreases dramatically to 20.8 kJ mol⁻¹ at H₂ coverage of 0.014 wt.%, levels to 17.9 at 0.073 wt.%, then gradually decreases to 2.6 kJ mol⁻¹ at 0.13 wt.% and closes to that of the plain carbon at H₂ coverage above 0.13 wt.%. These results suggest that the introduction of Pt particles significantly enhances the interaction between the adsorbed H₂ and the Pt-decorated carbon matrix at lower H₂ coverage, resulting in an adsorption process consisting of chemisorption stage, mixed nature of chemisorption and physisorption stage along with the increase of H₂ coverage (up to 0.13 wt.%). However, this enhancement in the interaction is outperformed by the added weight of the Pt and the blockage and/or occupation of some pores by the Pt nanoparticles, which results in lower H₂ uptake than that of the plain carbon.     

Synergistic catalytic effects of ZIF-67 and transition metals (Ni,Cu, Pd,and Nb) on hydrogen storage properties of magnesium

MgTM/ZIF-67 nanocomposites were prepared by the deposition-reduction method using ZIF-67, MgCl₂, and TMCl_x (TM = Ni, Cu, Pd, Nb) as raw materials. The dehydrogenation activation energies of MgTM/ZIF-67 (TM = Ni, Cu, Pd, Nb) nanocomposites were calculated to be 115.4 kJ mol⁻¹ H₂, 115.7 kJ mol⁻¹ H₂, 113.6 kJ mol⁻¹ H₂, and 75.8 kJ mol⁻¹ H₂, respectively; hence, the MgNb/ZIF-67 nanocomposite manifested the best comprehensive hydrogen storage performance. The hydrogen storage capacity of the MgNb/ZIF-67 nanocomposite was hardly attenuated after the 100th hydrogen absorption-desorption cycle. The dehydrogenated enthalpies of MgH₂ and CoMg₂H₅ in MgNb/ZIF-67 hydride were calculated to be 72.4 kJ mol⁻¹ H₂ and 81.0 kJ mol⁻¹ H₂, respectively, which were lower than those of additive-free MgH₂ and Mg/ZIF-67. The improved hydrogen storage properties of MgNb/ZIF-67 can be ascribed to the CoMg₂–Mg(Nb) core-shell structure and the catalytic effects of NbH and niobium oxide nanocrystals.     

Photothermal hydrogen production from oxidative hydrolysis of electrochemically synthesized nano-sized zinc

Proof of concept is established for low cost, scalable and safe access of hydrogen via photo-assisted oxidative hydrolysis of nano-sized zinc (Zn NPs). The Zn NPs with diameter of 40–50 nm are electrochemically grown on copper plate in conventional three electrode system at applied bias of 0.7 V. These NPs have long-range absorptivity from Visible-NIR region and directly employed for photothermal hydrogen production. The highest H₂ production rates of 0.2 mmolh⁻¹ and 0.43 mmolh⁻¹ are observed under illumination of tungsten light and concentrated sunlight respectively. In addition, Zn nanoparticles have shown great potential for CO₂ photoreduction. Under CO₂ microenvironment and tungsten light illumination, maximum H₂ production rate of 0.3 mmolh⁻¹ is achieved along with formation of 0.116 mgL⁻¹ formic acid. The significant enhancement may attribute to zinc nanoscale dimension which eventuates the hydroxylation rate and also increases the localized temperature by oscillating its surface electrons in resonance with incident radiation.     

Improved hydrogen storage properties of Mg-based nanocomposite by addition of LaNi5 nanoparticles

Mg (200 nm) and LaNi₅ (25 nm) nanoparticles were produced by the hydrogen plasma-metal reaction (HPMR) method, respectively. Mg–5 wt.% LaNi₅ nanocomposite was prepared by mixing these nanoparticles ultrasonically. During the hydrogenation/dehydrogenation cycle, Mg–LaNi₅ transformed into Mg–Mg₂Ni–LaH₃ nanocomposite. Mg particles broke into smaller particles of about 80 nm due to the formation of Mg₂Ni. The nanocomposite showed superior hydrogen sorption kinetics. It could absorb 3.5 wt.% H₂ in less than 5 min at 473 K, and the storage capacity was as high as 6.7 wt.% at 673 K. The nanocomposite could release 5.8 wt.% H₂ in less than 10 min at 623 K and 3.0 wt.% H₂ in 16 min at 573 K. The apparent activation energy for hydrogenation was calculated to be 26.3 kJ mol⁻¹. The high sorption kinetics was explained by the nanostructure, catalysis of Mg₂Ni and LaH₃ nanoparticles, and the size reduction effect of Mg₂Ni formation.     

Recoverable Ni2Al3 nanoparticles and their catalytic effects on Mg-based nanocomposite during hydrogen absorption and desorption cycling

The Mg-3.9 wt% Ni₂Al₃ nanocomposite is produced by hydrogen plasma-metal reaction method. The particle size of Mg is in range of 40–160 nm with an average size of 90 nm. The Ni₂Al₃ nanoparticles (NPs) of about 9 nm uniformly disperse on the surface of Mg NPs and in situ transform to Mg₂NiH_0.3 and Al after hydrogen absorption process. Surprisingly, the Mg₂NiH_0.3 and Al can recover to the initial state of Ni₂Al₃ after hydrogenation/dehydrogenation cycle. The Mg-Ni₂Al₃ nanocomposite shows enhanced hydrogen sorption rate and storage capacity. It can quickly uptake 6.4 wt% H₂ within only 10 min at 573 K, and release 6.1 wt% H₂ within 10 min at 623 K. The apparent activation energies for hydrogenation and dehydrogenation are calculated to be 55.4 and 115.7 kJ mol^?1 H₂. The enhanced hydrogen storage performances of the Mg-Ni₂Al₃ nanocomposite are attributed to both the nanostructure of Mg and the catalytic effects of Ni₂Al₃ NPs.     

Comparative study on hydrogenation properties of Pd capped Mg and Mg/Al films

Recent emergence of Mg as a promising hydrogen storage material with 7.6 wt% hydrogen encourages study on its thin films to understand physics of storage mechanism. The present study investigates the variations in hydrogen storage properties of Pd sandwiched Mg films upon introduction of Al layer. Multilayered stack of Pd/Mg/Pd and Pd/Al/Mg/Pd were grown on Si substrate using vapor deposition method and further hydrogenated at 150° C under 2 bar H₂ pressure for 2 h. Elastic Recoil Detection Analysis (ERDA) technique with 120 MeV Ag⁹⁺ ions was used to obtain hydrogen concentration versus incident ion fluence. ERDA study reveals that Pd/Mg/Al/Pd films absorb 6.01 × 10¹⁸hydrogen atoms/cm² in comparison to 4 × 10¹⁷ atoms/cm² absorbed by Pd/Mg/Pd system.     

Electrospun carbon nanofiber-encapsulated NiS nanoparticles as an efficient catalyst for hydrogen production from hydrolysis of sodium borohydride

Carbon nanofibers (CNFs) incorporating NiS nanoparticles (NPs), namely NiS@CNFs were prepared by one-step electrospinning and successfully employed as a catalyst for hydrogen production from hydrolytic dehydrogenation of sodium borohydride (SBH). As-prepared NiS@CNFs, composed of polyacrylonitrile (PAN), nickel acetate, and ammonium sulfide, was calcined at 900 °C in argon atmosphere, and characterized using standard surface science techniques. The combined results revealed the growth of NiS NPs inside the CNFs, hence confirmed the presence of elemental Ni, S, and C. The as-prepared NiS@CNFs catalyst has a significantly higher surface area (650.92 m²/g) than the reported value of 376 m²/g. Importantly, this catalyst exhibited a much higher catalytic performance, for H₂ production from SBH, than that of Ni@CNFs, as evidenced by its low activation energy (∼25.11576 kJ/mol) and their R_max values of 2962 vs. 1770 mL/g·min. Recyclability tests on using NiS@CNFs catalyst showed quantitatively production (∼100% conversion) of H₂ from SBH and retained up to 70% of its initial catalytic activity after five successive cycles. The low cost and high catalytic performance of the designed NiS@CNFs catalyst enable facile H₂ production from readily available hydrogen storage materials.     

Fine-tuning catalytic performance of ultrafine bimetallic nickel-platinum on metal-organic framework derived nanoporous carbon/metal oxide toward hydrous hydrazine decomposition

Heterogeneous catalysts with a high performance as well as low cost is pivotal but still challenging for hydrous hydrazine (N₂H₄·H₂O) as a hydrogen storage material. Herein, bimetallic PtNi nanoparticles are well dispersed on nitrogen doped porous carbon/zirconia support (PtNi/NC-ZrO₂). PtNi/NC-ZrO₂ nanocatalysts could be responsive and completely for catalyzing hydrous hydrazine decomposition with a H₂ selectivity of 100% as well as a turnover frequency of 1716 h⁻¹ measured at 323 K, outperforming most heterogeneous metal catalysts. This is mainly attributed that bi-support NC-ZrO₂ can efficiently expedite the electron transfer to metallic NPs and re-construct the electronic structure bimetallic active sites for selectively catalyzing hydrous hydrazine decomposition.     

Mg@C60 nano-lamellae and its 12.50 wt% hydrogen storage capacity

The design and synthesis of new hydrogen storage materials with high capacity are the prerequisite for extensive hydrogen energy application which can be achieved by multi-site hydrogen storage. Herein, a Mg@C₆₀ nano-lamellae structure with multiple hydrogen storage sites has been prepared through a simple ball-milling process in which Mg nanoparticles (∼5 nm) are homogeneously dispersed on C₆₀ nano-lamellae. The as-obtained C₆₀/Mg nano-lamellae displays an excess hydrogen uptake of 12.50 wt% at 45 bar, which is far higher than the theoretical value (7.60 wt%) of metal Mg and the US Department of Energy (DOE) target (5.50 wt%, 2020 year), also the experimental values reported by now. The enhanced hydrogen storage mainly comes from several storage sites: MgH₂, H_x–C₆₀ (CH chemical bonding), H₂@C₆₀ (the endohedral H₂ in C₆₀). Interestingly, the hybridization of Mg and C₆₀ not only facilitate the dissociation of H₂ molecules to form CH bonding with C₆₀, but also promote the deformation of C₆₀ and access H₂ molecules into the cavity of C₆₀. This work provides new insight into the underlying chemistry behind the high hydrogen storage capacities of a new class of hydrogen storage materials, fullerene/alkaline-earth metals nanocomposites.     

Co,Ni-based nanoparticles supported on graphitic carbon nitride nanosheets as catalysts for hydrogen generation from the hydrolysis of ammonia borane under broad-spectrum light irradiation

From the viewpoint of tailoring the atomic and nanoscale structures of semiconductors to enhance the solar-to-hydrogen energy conversion, we employed an in-situ gas template-assisted co-polymerization route, where melamine and 2,4,6-triaminopyrimidine were co-monomers and NH₄Cl was the in-situ gas template, to synthesize porous broad-spectrum light-responsive carbon nitride nanosheet (termed as CNN) species with increased π-electron availability. Then we developed CNN-supported Co and Ni nanoparticles (NPs) for catalytic hydrogen generation from aqueous ammonia borane (NH₃BH₃) under light irradiation (λ ≥ 420 nm) at room temperature. Though all the Co-based catalysts had the similar activities with total turnover frequency (TOF) values of 37.5–44.1 min⁻¹ in the dark, they exhibited significantly different and enhanced photocatalytic activities. Remarkably, the optimized catalyst had a total TOF value of 123.2 min⁻¹, exceeding the values of reported non-noble metal catalysts. Moreover, the porous CNN species possessed the C-substitution for N, tunable narrow bandgaps of 0.71–2.34 eV and efficient separation of photogenerated charge carriers. This resulted in the enriched electron density of metal NPs and the apparent quantum yield of 66.9% at 420 nm.     

Highly efficient Co/NC catalyst derived from ZIF-67 for hydrogen generation through ammonia decomposition

Small-size cobalt nanoparticles (NPs) distributed on nitrogen doped carbon support (Co/NC-X) were prepared by pyrolysis of ZIF-67 at various temperatures (X = 500, 600,700 and 800 °C) in nitrogen atmosphere and utilized as catalysts for hydrogen production through ammonia decomposition. Characterizations of the catalysts including XRD, HRTEM, XPS, H₂-TPR, CO₂-TPD, etc., were conducted for structure analysis. The N–C plate obtained from pyrolysis was coated with Co NPs to hinder its aggregation, which made the Co NPs dispersed evenly and increased their dispersion. The calcination temperature and the strong base of the support can adjust the strength of Co–N bond. The activity of the Co/NC-X catalysts is attributed to the high content of Co⁰ and the moderate Co–N bond strength. The ammonia decomposition activity of Co/NC-X catalysts in this paper is higher than many reported Co-based catalysts. Co/NC-600 catalyst demonstrates an ammonia conversion of 80% at 500 °C with a space velocity of 30,000 ml g_cat^?1 h^?1, corresponding to a hydrogen production rate of 26.8 mmol H₂ g_cat^?1 min^?1. The work provides insight for the development of highly active cobalt-based catalysts for hydrogen production through ammonia decomposition.