Massive Transformation in the Y2O3-Bi2O3 System

Cubic solid solutions in the Y₂O₃-Bi₂O₃ system with ∼25% Y₂O₃ undergo a transformation to a rhombohedral phase when annealed at temperatures ≤ 700°C. This transformation is composition-invariant and is thermally activated, and the product phase can propagate across matrix grain boundaries, indicating that there is no special crystallo-graphic orientation relationship between the product and the parent phases. Based on these observations, it is proposed that cubic → rhombohedral phase transformation in the Y₂O₃-Bi₂O₃ system is a massive transformation. Samples of composition 25% Y₂O₃-75% Bi₂O₃ with and without aliovalent dopants were annealed at temperatures ≤ 700°C for up to 10000 h. ZrO₂ as a dopant suppressed while CaO and SrO as dopants enhanced the kinetics of phase transformation. The rate of cubic/rhombohedra1 interface migration (growth rate or interface velocity) was also similarly affected by the additions of dopants; ZrO₂ suppressed while CaO enhanced the growth rate. Diffusion studies further showed that ZrO₂ suppressed while CaO enhanced cation interdiffusion coefficient. These observations are rationalized on the premise that cation interstitials are more mobile compared to cation vacancies in cubic bismuth oxide. The maximum growth rate measured was ∼10⁻¹⁰ m/s, which is orders of magnitude smaller than typical growth rates measured in metallic alloys. This difference is explained in terms of substantially lower diffusion coefficients in these oxide systems compared to metallic alloys.     

High-Temperature Creep of Y2O3-Stabilized ZrO2

The compression creep behavior of Y₂O₃-stabilized ZrO₂ (YSZ) was studied at temperatures to 2000 ° C. The function of Y₂O₃ content and grain size was tested in specimens with various impurity concentrations and porosity distributions. For relatively fine-grained specimens, creep rates increased with the 1.5 power of the applied stress at low stresses and with the third power at high stresses. The results for coarse-grained specimens can, in general, be fit by the cube dependence. The 1.5 power can be reduced to a linear dependence by correcting for an apparent threshold stress, which decreases with increasing temperature. Creep activation energies for YSZ are 128 ± 10 kcal/mol, independent of Y₂O₃ content, impurity level, grain size, and porosity distribution. In addition, over a broad range of temperatures and stresses the absolute values of the steady-state creep rates are influenced only by grain size and O₂ partial pressure.     

Transformation-Toughened ZrO2: Correlations between Grain Size Control and Composition in the System ZrO2-Y2O3

The average grain size of ZrO₂(+Y, o,) materials sintered at 1400°C was observed to depend significantly on the Y₂O₃ content. The average grain size decreased by a factor of 4 to 5 for Y₂O₃ contents between 0.8 and 1.4 mol% and increased at Y₂O₃ contents of 6.6 mol%. Grain growth control by a second phase is the concept used to interpret these data; compositions with a small grain size lie within the two-phase tetragonal + cubic phase field, and the size of the tetragonal grains is believed to be controlled by the cubic grains. This interpretation suggests that the Y₂O₃-rich boundary of the two-phase field lies between 0.8 and 1.4 mol% Y₂O₃. Transformation toughened materials fabricated in this binary system must have a composition that lies within the two-phase field to obtain the small grain size required, in part, to retain the tetragonal toughening agent.     

Densification and Grain Growth of Al2O3 Nanoceramics During Pressureless Sintering

α - Al₂O₃ nanopowders with mean particle sizes of 10, 15, 48, and 80 nm synthesized by the doped α-Al₂O₃ seed polyacrylamide gel method were used to sinter bulk Al₂O₃ nanoceramics. The relative density of the Al₂O₃ nanoceramics increases with increasing compaction pressure on the green compacts and decreasing mean particle size of the starting α-Al₂O₃ nanopowders. The densification and fast grain growth of the Al₂O₃ nanoceramics occur in different temperature ranges. The Al₂O₃ nanoceramics with an average grain size of 70 nm and a relative density of 95% were obtained by a two-step sintering method. The densification and the suppression of the grain growth are achieved by exploiting the difference in kinetics between grain-boundary diffusion and grain-boundary migration. The densification was realized by the slower grain-boundary diffusion without promoting grain growth in second-step sintering.     

Cation Tracer Diffusion in Cr2O3 and Cr2O3-0.09 wt% Y2O3

The cation diffusivities in the lattice and along dislocations and grain boundaries have been measured on sintered polycrysals of Cr₂O₃; and Cr₂Cr₂O₃-0.09 wt% Y₂O₃ at1100°C and at the pO₂ corresponding to that of Cr/Cr₂O₃ equilibrium at that temperature. Results for lattice and dislocation diffusivities in pure Cr₂O₃ are in good agreement with previous work. The present results indicate that yttrium additions have negligible effect on lattice and dislocation diffusion. However, grain-boundary diffusion in pure Cr₂O₃ is significantly slower than grain-boundary diffusion in Cr₂O₃-0.09 wt% Y₂O₃. The results are discussed in terms of their implications for the reactive-element effect in high-temperature oxidation of chromium-containing alloys.     

Hindrance of Grain Growth in Al2O3 by ZrO2 Inclusions.

Alumina and Al₂O₃/ZrO₂ (1 to 10 vol%) composite powders were mixed and consolidated by a colloidal method, sintered to >98% theoretical density at 1550°C, and subsequently heat-treated at temperatures up to 1700°C for grain-size measurements. Within the temperature range studied, the ZrO₂ inclusions exhibited sufficient self-diffusion to move with the Al₂O₃ 4-grain junctions during grain growth. Growth of the ZrO₂, inclusions occurred by coalescence. The inclusions exerted a dragging force at the 4-grain junctions to limit grain growth. Abnormal grain growth occurred when the inclusion distribution was not sufficiently uniform to hinder the growth of all Al₂O₃ grains. This condition was observed for compositions containing ≤2.5 vol% ZrO₂, where the inclusions did not fill all 4-grain junctions. Exaggerated grains consumed both neighboring grains and ZrO₂, inclusions. Grain-growth control (no abnormal grain growth) was achieved when a majority (or all) 4-grain junctions contained a ZrO₂ inclusion, viz., for compositions containing ≥5 vol% ZrO₂. For this condition, the grain size was inversely proportional to the volume fraction of the inclusions. Since the ZrO₂ inclusions mimic voids in all ways except that they do not disappear, it is hypothesized that abnormal grain growth in single-phase materials is a result of a nonuniform distribution of voids during the last stage of sintering.     

Critical Microstructures for Microcracking in Al2O3-ZrO2 Composites

The internal strains asSociated with the martensitic phase transformation of zirconia were used to introduce microcracks into Al₂O₃/ZrO₂ composites. The degree of transformation was found to be dependent on the volume fraction of ZrO₂ and its size, the latter of which could be controlled by suitable heat treatments. The microstructural changes that occurred during the heat treatments were studied using quantitative microscopy and X-ray diffraction. For materials containing more than 7.5 vol% Zr0₂, the ZrO₂ particles were found to pin the Al₂O₃ grain boundaries, thus limiting the Al₂O₃ grain growth. The limiting grain size was found to be dependent on size and volume fraction of ZrO₂. Heat treatments for the higher volume fraction materials (>7.5 vol% ZrO₂) caused micro-structural changes which resulted in increased amounts of monoclinic ZrO₂ at room temperature; elastic modulus measurements indicated that this was occurring concurrently with microcracking. By combining the ZrO₂ grain-size distributions with the X-ray analysis it was possible to calculate the critical ZrO₂ size required for the transformation. The critical size was found to decrease with increasing amounts of ZrO₂. Hardness and indentation fracture toughness were measured on the composites. Grain fragmentation was observed at the edge of the indentations and microcracks were observed directly, using an AgNO₃ decoration technique, near the indentations.     

Grain Growth in Sintered ZnO and ZnO-Bi2O3 Ceramics

Grain growth in a high-purity ZnO and for the same ZnO with Bi₂O₃ additions from 0.5 to 4 wt% was studied for sintering from 900° to 1400°C in air. The results are discussed and compared with previous studies in terms of the phenomenological kinetic grain growth expression: G ⁿ— G ⁿ₀= K ₀ t exp(— Q/RT ). For the pure ZnO, the grain growth exponent or n value was observed to be 3 while the apparent activation energy was 224 ± 16 kJ/mol. These parameters substantiate the Gupta and Coble conclusion of a Zn²⁺ lattice diffusion mechanism. Additions of Bi₂O₃ to promote liquidphase sintering increased the ZnO grain size and the grain growth exponent to about 5, but reduced the apparent activation energy to about 150 kJ/mol, independent of Bi₂O₃ content. The preexponential term K ₀ was also independent of Bi₂O₃ content. It is concluded that the grain growth of ZnO in liquid-phase-sintered ZnO-Bi₂O₃ ceramics is controlled by the phase boundary reaction of the solid ZnO grains and the Bi₂O₃-rich liquid phase.     

Strength Degradation and Crack Propagation in Thermally Shocked Al2O3

Strength degradation and crack propagation in Al₂O₃ are shown to depend on the initial strength and grain size of the material. The strengths of single-crystal sapphire and polycrystalline Al₂O₃ specimens with grain sizes of 10, 34, and 40 μ m decreased discontinuously at the critical quenching temperature. In contrast, the strength of polycrystalline Al₂O₃ with a grain size of 85 μm decreased gradually as the quenching temperature increased. The strength retained after thermal shock and the extent of crack propagation decrease with increasing initial strength and grain size, respectively, in Al₂O₃.     

Grain Growth in Two-Phase Ceramics: Al2O3 Inclusions in ZrO

The effect of Al₂O₃ inclusions with a greater average size (0.6 μm) than the average particle size of the major phase powder (<0.1 μm) on grain gowth was examined by sintering ZrO₂/Al₂O₃ composites (0,3,5,10, and 20 vol%) at 1400°C and then heat-treating at temperatures up to 1700°C. Normal grain growth was observed for all conditions. The inclusions appeared to have no effect on grain growth until the ZrO₂ grain size was ∼1.5 times the average inclusion size. Grain growth inhibition increased with volume fraction of the Al₂O₃ inclusion phase. At temperatures 1600°C, the inclusions were relatively immobile and most were located within the ZrO₂ grains for volume fractions <0.20; at higher temperatures, the inclusions could move with the grain boundary to coalesce. Grain growth was less inhilited when the inclusions could move with the boundaries, resulting in a larger increase in grain size than observed at lower temperatures. Analogies between mobile voids, entrapped within grain at lower temperature due to abnormal grain growth during the last state of sintering, and the observations concerning the mobile inclusions are made suggesting that grain-boundary movement can "sweep" voids to grain boundaries and eventually of four-grain junctions, where they are more likely to disappear by mass transport.     

Effect of Aqueous Processing Conditions on the Microstructure and Transformation Behavior in Al2O3─ZrO2(CeO2) Composites

Aqueous processing of Al₂O₃─ZrO₂ (123 mol% CeO₂) composites, combined with sintering conditions, was used to control the microstructure and its influence on the martensitic transformation temperature of t -ZrO₂ and the transformation-toughening contribution at room temperature. The resultant ZrO₂ grain sizes in the dense composites were related to the transformation-toughening behavior of t -ZrO₂. The data show that (1) the best processing conditions exist when the electrophoretic mobilities of the two solids are positive, adequately high to ensure colloidal stability, efficient packing,and uniform ZrO₂ distribution but differ greatly in magnitude, (2) the colloidal stability of ZrO₂ controls the overall stability and the rheological and processing behavior of this mixture, (3) the grain size distribution in dense pieces sintered for 1 h at 1500°C is comparable to the particle size distribution of the powders, (4) the martensite start temperature for the tetragonal to-monoclinic transformation in Al₂O₃ containing 20 and 40 vol% ZrO₂ increases and can approach 0°C with increasing average ZrO₂ grain size, and as a result, (5) the fracture toughness values at room temperature are raised from 4–5 MPa.m^1/2 to 9–12 MPa.m^1/2 for these two compositions.     

Grain Growth of ZnO in ZnO-Bl2O3 Ceramics with Ai2O3 Additions

Grain growth of ZnO during liquid-phase sintering of a ZnO-6 wt% Bi₂O₃ ceramic was investigated for A1₂O₃ additions from 0.10 to 0.80 wt%. Sintering in air for 0.5 to 4 h at 900° to 1400°C was studied. The AI₂O₃ reacted with the ZnO to form ZnAl₂O₄ spinel, which reduced the rate of ZnO grain growth. The ZnO grain-growth exponent was determined to be 4 and the activation energy for ZnO grain growth was estimated to be 400 kJ/mol. These values were compared with the activation parameters for ZnO grain growth in other ceramic systems. It was confirmed that the reduced ZnO grain growth was a result of ZnAl₂O₄ spinel particles pinning the ZnO grain boundaries and reducing their mobility, which explained the grain-growth exponent of 4. It was concluded that the 400 kJ/mol activation energy was related to the transport of the ZnAl₂O₄ spinel particles, most probably controlled by the diffusion of O^2- in the ZnAl₂O₄ spinel structure.     

Rapid Rate Sintering of Nanocrystalline ZrO2−3 mol% Y2O3

Conventional ramp-and-hold sintering with a wide range of heating rates was conducted on submicrometer and nanocrystalline ZrO₂–3 mol% Y₂O₃ powder compacts. Although rapid heating rates have been reported to produce high density/fine grain size products for many submicrometer and smaller starting powders, the application of this technique to ZrO₂–3 mol% Y₂O₃ produced mixed results. In the case of submicrometer ZrO₂–3 mol% Y₂O₃, neither densification nor grain growth was affected by the heating rate used. In the case of nanocrystalline ZrO₂–3 mol% Y₂O₃, fast heating rates severely retarded densiflcation and had a minimal effect on grain growth. The large adverse effect of fast heating rates on the densification of the nanocrystalline powder was traced to a thermal gradient/differential densification effect. Microstructural evidence suggests that the rate of densification greatly exceeded the rate of heat transfer in this material; consequently, the sample interior was not able to densify before being geometrically constrained by a fully dense shell which formed at the sample exterior. This finding implies that rapid rate sintering will meet severe practical constraints in the manufacture of bulk nanocrystalline ZrO₂–3 mol% Y₂O₃ specimens.     

Degradation During Aging of Transformation-Toughened ZrO2-Y2O3 Materials at 250°C

The detrimental aging phenomenon observed in ZrO₂-Y₂O₃ materials, which causes tetragonal ZrO₂ to transform to its monoclinic structure at temperatures between 150 and 400°C, was investigated with respect to the gaseous aging environment and the Y₂O₃ and SiO₂ content of the material. It is shown that the aging phenomenon is caused by water vapor and that inter-granular silicate glassy phases play no significant role. Transmission electron microscopy of thin foils, before and after aging, showed that the water vapor reacted with yttrium in the ZrO₂ to produce clusters of small (20 to 50 nm) crystallites of α-Y(OH)₃. It is hypothesized that this reaction produces a monoclinic nucleus (depleted of Y₂O₃) on the surface of an exposed tetragonal grain. Monoclinic nuclei greater than a critical size grow spontaneously to transform the tetragonal grain. If the transformed grain is greater than a critical size, it produces a microcrack which exposes subsurface tetragonal grains to the aging phenomenon and results in catastrophic degradation. Degradation can be avoided if the grain size is less than the critical size required for microcracking.     

Conversion from β-Ce2O3·11Al2O3 to α-Al2O3 in Tetragonal ZrO2 Matrix

Composites of β-Ce₂O₃·11Al₂O₃ and tetragonal ZrO₂ were fabricated by a reductive atmosphere sintering of mixed powders of CeO₂, ZrO₂ (2 mol% Y₂O₃), and Al₂O₃. The composites had microstructures composed of elongated grains of β-Ce₂O₃·11Al₂O₃ in a Y-TZP matrix. The β-Ce₂O₃·11Al₂O₃ decomposed to α-Al₂O₃ and CeO₂ by annealing at 1500°C for 1 h in oxygen. The elongated single grain of β-Ce₂O₃·11Al₂O₃ divided into several grains of α-Al₂O₃ and ZrO₂ doped with Y₂O₃ and CeO₂. High-temperature bending strength of the oxygen-annealed α-Al₂O₃ composite was comparable to the β-Ce₂O₃·11Al₂O₃ composite before annealing.     

Preparation of NiAl2O4/SiO2 and Co2+-Doped NiAl2O4/SiO2 Nanocomposites by the Sol–Gel Route

NiAl₂O₄/SiO₂ and Co²⁺-doped NiAl₂O₄/SiO₂ nanocomposite materials of compositions 5% NiO – 6% Al₂O₃– 89% SiO₂ and 0.2% CoO – 4.8% NiO – 6% Al₂O₃– 89% SiO₂, respectively, were prepared by a sol–gel process. NiAl₂O₄ and cobalt-doped NiAl₂O₄ nanocrystals were grown in a SiO₂ amorphous matrix at around 1073 K by heating the dried gels from 333 to 1173 K at the rate of 1 K/min. The formations of NiAl₂O₄ and cobalt-doped NiAl₂O₄ nanocrystals in SiO₂ amorphous matrix were confirmed through X-ray powder diffraction, Fourier transform infrared spectroscopy, differential scanning calorimeter, transmission electron microscopy (TEM), and optical absorption spectroscopy techniques. The TEM images revealed the uniform distribution of NiAl₂O₄ and cobalt-doped NiAl₂O₄ nanocrystals in the amorphous SiO₂ matrix and the size was found to be ∼5–8 nm.     

Fabrication and Microstructure of Al2O3–SiC–YAG Hybrid Composites Prepared by Particulate Dispersion

Stable Al₂O₃–SiC–YAG hybrid composites were successfully fabricated by reaction of Al₂O₃ and Y₂O₃ and incorporation of SiC. The hot-pressed bodies consisted of uniformly dispersed grains of microsized YAG particulates and nanosized SiC particulates in an Al₂O₃ matrix. Although the grain size of monolithic A1₂O₃ increases markedly with increased temperature, the grain size of the Al₂O₃–SiC–YAG hybrid composites was effectively restrained due to grain-boundary pinning by the particulates.     

Effects of Addition of Na2O, Sb2O3, CaO, and ZrO2 on the Properties of Lithium Zinc Ferrite

Some effects of CaO, Na₂O, Sb₂O₃, and ZrO₂ additions on Li_0.3Zn_0.4Fe_2.3O₄ ferrite were studied to improve its density and other material properties. The densification behavior of the ferrite depended on the amount and type of additive. A relative density of ∼98.5% was achieved with the addition of CaO. The grain size decreased with the addition of Na₂O, CaO, and Sb₂O₃. The permeability and electrical resistivity increased with additives. CaO remarkably increased resistvity, whereas, ZrO₂ increased permeability. Na₂O and Sb₂O₃ increased the Curie temperature, whereas CaO and ZrO₂ decreased it. These effects were attributed to mainly additive segregation on the grain boundaries, which suppressed grain-size development during the sintering of lithium zinc ferrite.     

Formation, Characterization, and Hot Isostatic Pressing of Cr2O3-Doped ZrO2 (0,3 mol% Y2O3) Prepared by Hydrazine Method

In the ZrO₂-Cr₂O₃ system, metastable t -ZrO₂ solid solutions containing up to 11 mol% Cr₂O₃ crystallize at low temperatures from amorphous materials prepared by the hydrazine method. The lattice parameter c decreases linearly from 0.5149 to 0.5077 nm with increased Cr₂O₃ content, whereas the lattice parameter a is a constant value ( a = 0.5077 nm) regardless of the starting composition. At higher temperatures, transformation (decomposition) of the solid solutions proceeds in the following way: t (ss)→ t (ss) + m + Cr₂O₃→ m + Cr₂O₃. Above 11 mol% Cr₂O₃ addition, c-ZrO₂ phases are formed in the presence of Cr₂O₃. The t -ZrO₂ solid solution powders have been characterized for particle size, shape, and surface area. They consist of very fine particles (15–30 nm) showing thin platelike morphology. Dense ZrO₂(3Y)-Cr₂O₃ composite ceramics (∼99.7% of theoretical) with an average grain size of 0.3 μm have been fabricated by hot isostatic pressing for 2 h at 1400°C and 196 MPa. Their fracture toughness increases with increased Cr₂O₃ content. The highest K _Ic value of 9.5 MPa·;m^1/2 is achieved in the composite ceramics containing 10 mol% Cr₂O₃.     

Sintering, Microstructure, Hardness, and Fracture Toughness Behavior of Y2O3-CeO2-ZrO2

A wet-chemical approach is applied to derive fine powders with compositions 11 mol% CeO₂-ZrO₂, 1 mol% YO_1.5-10 mol% CeO₂-ZrO₂, 12 mol% CeO₂-ZrO₂, and 2 mol% YO_1.5-10 mol% CeO₂-ZrO₂ by the coprecipitation method. The characteristics of the as-derived powders are evaluated through thermal analysis and electron microscopy. The sintering behavior of the calcined powders is carried out at 1400° and 1500°C for 1 to 10 h. Sintered density higher than 98% of theoretical is achieved for sintering at 1400°C for several hours. The as-sintered density dependence on the sintering condition is related to the extent of tetragonal-to-monoclinic phase transformation as well as the associated microcracks. Partial substitution by Y₂O₃ in CeO₂-ZrO₂ results in reduced grain size and tends to stabilize the tetragonal structure. Y₂O₃ is more effective than CeO₂ with respect to the grain size refinement and tetragonal stability. In addition, Y₂O₃ substitution in CeO₂-ZrO₂ increases the hardness, while it decreases the fracture toughness.