Preparation of steam activated carbon from rubberwood sawdust (Hevea brasiliensis) and its adsorption kinetics

Activated carbon was produced from a biowaste product, rubberwood sawdust (RWSD) using steam in a high temperature fluidized bed reactor. Experiments were carried out to investigate the influence of various process parameters such as activation time, activation temperature, particle size and fluidising velocity on the quality of the activated carbon. The activated carbon was characterized based on its iodine number, methylene blue number, Brauner Emmet Teller (BET) surface area and surface area obtained using the ethylene glycol mono ethyl ether (EGME) retention method. The best quality activated carbon was obtained at an activation time and temperature of 1h and 750 degrees C for an average particle size of 0.46 mm. The adsorption kinetics shows that pseudo-second-order rate fitted the adsorption kinetics better than pseudo-first-order rate equation. The adsorption capacity of carbon produced from RWSD was found to be 1250 mg g(-1) for the Bismark Brown dye. The rate constant and diffusion coefficient for intraparticle transport were determined for steam activated carbon. The characteristic of the prepared activated carbon was found comparable to the commercial activated carbon.     

Chromium(VI) adsorption from aqueous solution onto Moroccan Al-pillared and cationic surfactant stevensite

Batch adsorption of the chromium(VI) onto Moroccan stevensite pillared by Keggin aluminium hydroxypolycation (Al-stevensite) and cationic surfactant cetyltrimethylammoniumbromide (CTA-stevensite) was investigated. The results showed that the CTA-stevensite has a higher affinity than that of Al-stevensite for chromium(VI) adsorption. The adsorption capacities for natural stevensite, Al-stevensite and CTA-stevensite calculated according to the Dubinin-Kaganer-Radushkevich isotherm (DKR) are 13.7, 75.4 and 195.6mmolkg(-1), respectively. The study of the pH effect showed that the optimal range corresponding to the Cr(VI) maximum adsorption on Al-stevensite is pH 3.5-6 and that on CTA-stevensite is pH 2-6. The adsorption rates evaluated according to the pseudo-second-order model are 7.2, 207.2 and 178.5mmolkg(-1)min(-1) for the natural stevensite, Al-stevensite and CTA-stevensite, respectively. The low values of the adsorption energy calculated by (DKR) suggest that anion exchange is the main mechanism that governs the chromate adsorption.     

Equilibrium and kinetic studies on free cyanide adsorption from aqueous solution by activated carbon

Adsorption equilibrium and kinetics of free cyanide onto activated carbon were investigated in the batch tests, and the effects of contact time (1–72 h) and initial cyanide concentrations in the range of 102–532 mg/L were studied. Linear regression was used to determine the best fit of equilibrium and kinetics expressions. The two-parameter models including Freundlich, Dubinin–Radushkevich, Temkin and four different linearized forms of Langmuir and three-parameter models including Redlich–Peterson and Koble–Corrigan were employed for fitting the equilibrium data and it was found that, three-parameter models fitted the data better than the two-parameter models and among the three-parameter models the equilibrium data are best represented by Koble–Corrigan model. A number of kinetic models including fractional power, zero order, first order, pseudo-first order, Elovich, second order, intraparticle diffusion and four different linearized forms of pseudo-second order models were tested to fit the kinetic data. The latter was found to be consistent with the data. Intraparticle diffusion plots show that the adsorption process of free cyanide is a two steps process. In the first step, the adsorption of cyanide is fast while in the second step, cyanide adsorption slows down.     

Removal of nitroimidazole antibiotics from aqueous solution by adsorption/bioadsorption on activated carbon

The objective of the present study was to analyse the behaviour of activated carbon with different chemical and textural properties in nitroimidazole adsorption, also assessing the combined use of microorganisms and activated carbon in the removal of these compounds from waters and the influence of the chemical nature of the solution (pH and ionic strength) on the adsorption process. Results indicate that the adsorption of nitroimidazoles is largely determined by activated carbon chemical properties. Application of the Langmuir equation to the adsorption isotherms showed an elevated adsorption capacity (X_m = 1.04–2.04 mmol/g) for all contaminants studied. Solution pH and electrolyte concentration did not have a major effect on the adsorption of these compounds on activated carbon, confirming that the principal interactions involved in the adsorption of these compounds are non-electrostatic. Nitroimidazoles are not degraded by microorganisms used in the biological stage of a wastewater treatment plant. However, the presence of microorganisms during nitroimidazole adsorption increased their adsorption on the activated carbon, although it weakened interactions between the adsorbate and carbon surface. In dynamic regime, the adsorptive capacity of activated carbon was markedly higher in surface water and groundwater than in urban wastewaters.     

Chromium (VI) adsorption on boehmite

Boehmite was synthesized and characterized in order to study the adsorption behavior and the removal of Cr(VI) ions from aqueous solutions as a function of contact time, initial pH solution, amount of adsorbent and initial metal ion concentration, using batch technique. Adsorption data of Cr(VI) on the boehmite were analyzed according to Freundlich, Langmuir and Dubinin-Radushkevich (D-R) adsorption models. Thermodynamic parameters for the adsorption system were determinated at 293, 303, 313 and 323K temperatures. The kinetic values and thermodynamic parameters from the adsorption process show that the Cr(VI) ions adsorption on boehmite is an endothermic and spontaneous process. These results show that the boehmite could be considered as a potential adsorbent for chromium ions in aqueous solutions.     

Error analysis of equilibrium studies for the almond shell activated carbon adsorption of Cr(VI) from aqueous solutions

In this study, the preparation of activated carbon from almond shell with H2SO4 activation and its ability to remove toxic hexavalent chromium from aqueous solutions are reported. The influences of several operating parameters such as pH, particle size and temperature on the adsorption capacity were investigated. Adsorption of Cr(VI) is found to be highly pH, particle size and temperature dependent. Four adsorption isotherm models namely, Langmuir, Freundlich, Tempkin and Dubinin-Radushkevich were used to analyze the equilibrium data. The Langmuir isotherm provided the best correlation for Cr(VI) onto the almond shell activated carbon (ASC). Adsorption capacity was calculated from the Langmuir isotherm as 190.3 mg/g at 323 K. Thermodynamic parameters were evaluated and the adsorption was endothermic showing monolayer adsorption of Cr(VI). Five error functions were used to treat the equilibrium data using non-linear optimization techniques for evaluating the fit of the isotherm equations. The highest correlation for the isotherm equations in this system was obtained for the Freundlich isotherm. ASC is found to be inexpensive and effective adsorbent for removal of Cr(VI) from aqueous solutions.     

Removal of chromium(VI) from aqueous solution by activated carbons: kinetic and equilibrium studies

The objective of this study is to assess the uptake of hexavalent chromium (Cr(VI)) from aqueous solutions onto activated carbons (AC) produced from wood. Two activated carbons are tested, a KOH-activated carbon and a commercial H3PO4-activated carbon (Acticarbone CXV). The adsorption of Cr(VI) is maximal at the lowest values of pH (pH 3) and increases with temperature for both adsorbents. The KOH-activated carbon shows higher capacity for adsorption of Cr(VI) than Acticarbone. The sorption isotherms fit the Langmuir model accurately. The adsorption reaction was found to obey a pseudo second-order rate. The activation energy and the pre-exponential factor as well as the thermodynamic functions related to adsorption reaction, DeltaS degrees , DeltaH degrees , DeltaG degrees , were determined. Nevertheless, the global reaction rate is probably controlled by the intra-particular diffusion of Cr(VI) and the mass diffusivity of Cr(VI) was evaluated.     

Kinetics of adsorption of dyes from aqueous solution using activated carbon prepared from waste apricot

Adsorbent (WA11Zn5) has been prepared from waste apricot by chemical activation with ZnCl(2). Pore properties of the activated carbon such as BET surface area, pore volume, pore size distribution, and pore diameter were characterized by N(2) adsorption and DFT plus software. Adsorption of three dyes, namely, Methylene Blue (MB), Malachite Green (MG), Crystal Violet (CV), onto activated carbon in aqueous solution was studied in a batch system with respect to contact time, temperature. The kinetics of adsorption of MB, MG and CV have been discussed using six kinetic models, i.e., the pseudo-first-order model, the pseudo-second-order model, the Elovich equation, the intraparticle diffusion model, the Bangham equation, the modified Freundlich equation. Kinetic parameters and correlation coefficients were determined. It was shown that the second-order kinetic equation could describe the adsorption kinetics for three dyes. The dyes uptake process was found to be controlled by external mass transfer at earlier stages (before 5 min) and by intraparticle diffusion at later stages (after 5 min). Thermodynamic parameters, such as DeltaG, DeltaH and DeltaS, have been calculated by using the thermodynamic equilibrium coefficient obtained at different temperatures and concentrations. The thermodynamics of dyes-WA11Zn5 system indicates endothermic process.     

Kinetics and thermodynamic of adsorption of chromium(VI) from aqueous solution using puresorbe

This paper deals with an investigation on coir-based adsorbent, puresorbe, in the removal of chromium(VI) from the aqueous solutions. The adsorption of chromium(VI) was carried out by varying the parameters such as agitation time, metal concentration, adsorbent dose, temperature and pH. The experimental isotherm data were analyzed using Langmuir, Freundlich and Redlich and Peterson isotherms. Adsorption followed second order rate expression for the particle size 250–500 μm at pH 2. The monolayer adsorption capacity is 76.92 mg chromium(VI) per gram of puresorbe. Thermodynamic parameters show the endothermic nature of chromium(VI) adsorption. Desorption study carried out using distilled water adjusted to pH of 2–10, suggests that chemisorption might be the mode of adsorption.     

Chromium adsorption and Cr(VI) reduction to trivalent chromium in aqueous solutions by soya cake

Chromium as Cr(VI) is a industrially produced pollutant. Hexavalent chromium can be reduced to the trivalent state using various reductive agents or it can be removed from solution by surface-active adsorbents. In this study, both of these methods were evaluated using soya cake. A high efficiency for reduction of Cr(VI) to trivalent chromium was observed at pH < 1. Increasing the temperature, also increased the yield. Experimentally, the optimum time and soya cake mass were 5h and 0.7 g, respectively. In the second treatment method, a high efficiency for adsorption of chromium was also observed at pH < 1. The favorable temperature for adsorption was found to be 20 degrees C. Experimentally, the best time was 1h and with increasing soya cake mass up to 30 g, the adsorption efficiency was increased. Dissolution of LiCl in the experimental solutions, increased the efficiency of adsorption, however, this effect was not observed in the case of KCl. Langmuir isotherm constants, Q and b, for ground soybeans, were found to be 2.8 x 10(-4)mg/mg and 0.623, respectively. Freundlich isotherm constants, K(f) and n, were found to be 1.4 x 10(-4) and 4.99, respectively.     

Removal of Cu(II) ions by activated poplar sawdust (Samsun clone) from aqueous solutions

In this work, adsorption of Cu(II) ions on sawdust (SD) and activated sawdust (ASD) has been studied by using batch adsorption techniques. The equilibrium adsorption level was determined to be a function of the pH, initial Cu(II) concentration, and adsorbent dosage. The equilibrium nature of Cu(II) adsorption has been described by the Freundlich and Langmuir isotherms. The experimental adsorption data were fitted to the Langmuir adsorption model both sawdust and activated sawdust. The equilibrium capacity of sawdust and activated sawdust were 5.432 and 13.495 mg copper per g adsorbent, respectively at room temperature and natural pH. The maximum adsorption capacity was obtained at the maximum zeta potential value that -74.5 mV (pH 5) for activated sawdust and at -48.4 mV (pH 4) for sawdust. It was observed that activated sawdust was a suitable adsorbent than sawdust for removal of Cu(II) from aqueous solutions.     

Adsorption of zinc(II) from an aqueous solution onto activated carbon.

Adsorption isotherms were measured experimentally for Zn(II) adsorption from aqueous solution onto commercial activated carbons C, F-400, F-300 and Centaur HSL in a batch adsorber. The effects of carbon type and solution pH on adsorption isotherms were evaluated in this work. Nearly three times as much Zn(II) adsorbed onto C carbon as on the other three carbon types. The adsorption isotherm for Zn(II) was dependent on solution pH since Zn(II) did not adsorb to carbon below pH 2, and the adsorption isotherm increased as pH increased from 3 to 7. The adsorption isotherm of Zn(II) on C carbon was temperature independent while on F-400 the isotherm showed unusual behavior as temperature increased.     

Impregnated activated carbon for the adsorption of Gd(III) radionuclides from aqueous solutions

Activated carbons (ACs) impregnated by FeCl₃, SnCl₄ and ZnCl₂ are used as adsorbents for the removal of Gd(III) radionuclides from aqueous solutions. Adsorption of Gd(III) is investigated as a function of pH, concentration of adsorbate, contact time, ionic strength and temperature. Gadolinium is efficiently removed (R%?>?95%) at pH values ≥4.8 (for FeAC and SnAC) and 2.9 (for ZnAC). The pseudo-first-order, the pseudo-second-order and Elovich kinetic models are used to analyze the kinetic data of Gd(III), at the studied concentrations (30, 100 and 200?mg/L) onto the employed materials. Of these models, Elovich is the only one that well-fitted the experimental kinetics onto the applied materials at all of the studied Gd(III) concentrations. Equilibrium data of Gd(III) are analyzed by the Freundlich, Temkin, Dubnin–Radushkevich (D-R) and Redlich–Petrson isotherm models. The adsorption efficiency of Gd(III) onto FeAC and SnAC is deleteriously affected by increasing the ionic strength, while adsorption onto ZnAC is unaffected. The thermodynamic parameters are calculated and it is revealed that the adsorption of Gd(III) onto the employed materials is an endothermic process. Desorption studies of Gd(III)-loaded ACs are performed using different desorbing agents (HCl, ZnCl₂, FeCl₃ and SnCl₄) at various concentrations (0.0005, 0.0025, 0.01 and 0.025?M).     

Adsorptive removal of heavy metals from aqueous solution by treated sawdust (Acacia arabica)

The removal of Cr(VI), Pb(II), Hg(II) and Cu(II), by treated sawdust has been found to be concentration, pH, contact time, adsorbent dose and temperature dependent. The adsorption parameters were determined using both Langmuir and Freundlich isotherm models. Adsorption capacity for treated sawdust, i.e. Cr(VI) (111.61 mg/g), Pb(II) (52.38 mg/g), Hg(II) (20.62 mg/g), and Cu(II) (5.64 mg/g), respectively. Surface complexation and ion exchange are the major removal mechanisms involved. The adsorption isotherm studies clearly indicated that the adsorptive behaviour of metal ions on treated sawdust satisfies not only the Langmuir assumptions but also the Freundlich assumptions. The applicability of Lagergren kinetic model has also been investigated. The adsorption follows first-order kinetics. Thermodynamic constant (k_ad), standard free energy (ΔG°), enthalpy (ΔH°) and entropy (ΔS°) were calculated for predicting the nature of adsorption. The percentage adsorption increases with pH to attain a maximum at pH 6 and thereafter it decreases with further increase in pH. The results indicate the potential application of this method for effluent treatment in industries and also provide strong evidence to support the adsorption mechanism proposed.     

Adsorption of Cr(VI) from aqueous solutions by spent activated clay

Adsorption of Cr(VI) onto spent activated clay (SAC), a waste produced from an edible oil refinery company, was investigated for its beneficial use in wastewater treatment. After pressure steam treatment, SAC was used as an adsorbent. The adsorption kinetic data were analyzed and fitted well in a pseudo-first-order equation and the rate of removal was found to speed up with decreasing pH and increasing temperature. Activation energy for the adsorption process was found to be 4.01–5.47 kcal/K mol. The Langmuir adsorption isotherm was used to fit the equilibrium data and the effect of pH, temperature and ionic strength were studied. The maximum adsorption capacities for Cr(VI) ranged from 0.743 to 1.422 mg/g for temperature between 4 and 40 °C under a condition of pH 2.0. The studies conducted show the process of Cr(VI) removal to be spontaneous at high temperature and endothermic in nature. From the waste utilization and environment point of view, the work carried out is important and useful. Results obtained can serve as baseline data for designing a treatment process using this low-cost adsorbent for the treatment of wastewater rich in Cr(VI).     

Removal of Cr(VI) from aqueous solutions using modified red pine sawdust

The adsorption of Cr(VI) from aqueous solutions on sawdust (SD), base extracted sawdust (BESD) and tartaric acid modified sawdust (TASD) of Turkish red pine tree (Pinus nigra), a timber industry waste, was studied at varying Cr(VI) concentrations, adsorbent dose, modifier concentration and pH. Batch adsorption studies have been carried out. Sawdust was collected from waste timber industry and modified with various amount of tartaric acid (TA) (0.1-1.5M). The batch sorption kinetics has been tested and the applicability of the Langmuir and Freundlich adsorption isotherms for the present system has been tested at 25+/-2 degrees C. Under observed test conditions, the equilibrium adsorption data fits the linear Freundlich isotherms. An initial pH of 3.0 was most favorable for Cr(VI) removal by all adsorbents. Maximum Cr(VI) was sequestered from the solution within 120 min after the beginning for every experiment. The experimental result inferred that chelation and ion exchange is one of the major adsorption mechanisms for binding metal ions to the SD. Percentage removal of Cr(VI) was maximum at the initial pH of 3.0 (87.7, 70.6 and 55.2% by TASD, BESD, and SD, respectively). Adsorption capacities range from 8.3 to 22.6 mg/g for SD samples.     

Dye removal from wastewater using activated carbon developed from sawdust: adsorption equilibrium and kinetics

Mahogany sawdust was used to develop an effective carbon adsorbent. This adsorbent was employed for the removal of direct dyes from spent textile dyeing wastewater. The experimental data were analysed by the Langmuir and Freundlich models of adsorption. Equilibrium data fitted well with the Langmuir model. The rates of adsorption were found to conform to the pseudo-second-order kinetics with good correlation. The equilibrium adsorption capacity of the sawdust carbon was determined with the Langmuir equation as well as the pseudo-second-order rate equation and found to be >300 mg dye per gram of the adsorbent. The most ideal pH for adsorption of direct dyes onto sawdust carbon was found to be 3 and below. The results indicate that the Mahogany sawdust carbon could be employed as a low cost alternative to commercial activated carbon in the removal of dyes from wastewater.     

Adsorption of nickel(II) from aqueous solution onto activated carbon prepared from almond husk

Activated carbon was prepared from almond husk by activating without (MAC-I) and with (MAC-II) H(2)SO(4) at different temperatures. The ability of the activated carbon to remove nickel(II) ions from aqueous solutions by adsorption has been investigated under several conditions such as pH, carbonisation temperature of husk, initial concentration of metal ions, contact time, and adsorbent concentration. Optimal conditions were pH 5.0, the carbonisation temperature of 700 degrees C, 50 min of contact time and adsorbent concentration of 5 g/l. The results indicate that the effective uptake of Ni(II) ions was obtained by activating the carbon, prepared from almond husk at 700 degrees C, through the addition of H(2)SO(4). The removal of Ni(II) were found to be 97.8% at initial concentration of 25mg/l and the adsorbent concentration of 5 g/l. When the adsorbent concentration was increased up to 40 g/l, the adsorption density decreased from 4.89 to 0.616 mg/g for MAC-II. In the isotherm studies, the experimental adsorption data fitted reasonably well the Langmuir isotherm for both MAC-I and MAC-II.     

Chromium(VI) removal from aqueous medium by maize cane and agave bagasse biomasses

Chromium(VI) is a major water pollutant from industrial effluents whose concentration is to be reduced within the permissible limits. In this paper, the use of maize cane and agave bagasse as inexpensive adsorbent for the removal of Cr(VI) from aqueous solutions is considered. In the first place, they were conditioned and characterized to determine their physicochemical properties with scanning electron microscopy; the elemental composition with energy-dispersive x-ray spectroscopy (EDS); the principal functional groups with Fourier transform infrared spectroscopy; thermal stability with thermogravimetric analysis; and surface properties by specific surface hydration kinetics, point of zero charge determination by mass titration, and active site density are described. In the second place, their adsorption properties for Cr(VI) from aqueous solution were evaluated in a batch system. The kinetics of Cr(VI) sorption with both natural adsorbents were described with a pseudo-second-order model. Equilibrium data were found to be best represented for both adsorbents by the Freundlich isotherm model. Maize cane and agave bagasse can be effectively used as an adsorbents for the removal of Cr(VI) ions from the aqueous solution.     

Influence of cationic surfactant on adsorption of Cr(VI) onto activated carbon

The effect of a cationic surfactant on the adsorption of Cr(VI) on activated carbon was investigated using cetylpyridinium chloride (CPC). At a concentration below the critical micelle concentration (CMC) of CPC, the adsorption of CPC and Cr(VI) reached equilibrium within 60 min, while it took 180 min at the concentration above CMC. CPC decreased the adsorption rate of Cr(VI) and increased the adsorption amount of Cr(VI) onto activated carbon. To analyze adsorption phenomena of Cr(VI), adsorption kinetic and isotherm were used and fitted well with the pseudo-second order kinetic model and Langmuir adsorption model, respectively. CPC introduced a cationic functional group on the surface of activated carbon and provided an adsorption site for Cr(VI).