Dynamic threshold voltage damascene metal gate MOSFET (DT-DMG-MOS)technology for very low voltage operation of under 0.7 V

We propose dynamic threshold-voltage damascene metal gate MOSFET (DT-DMG-MOS) technology for very low voltage operation (under 0.7 V). In this technology the metal gate is formed by the damascene gate process and directly connected to the well region (Si-body). Therefore, the connection between gate electrode and silicon body can be more easily fabricated in the DT-DMG transistor than with conventional technologies. Furthermore, we found that low threshold voltage (about 0.15 V reduction for CMOS), high drive current, excellent subthreshold swing (about 60 mV/decade), and uniform electrical characteristics (great reduction of threshold voltage deviation) were obtained in the transistors with midgap work function metal gates (Al/TiN or W/TiN) and low supply voltage (0.7 V)     

Damascene W/TiN gate MOSFETs with improved performance for 0.1-/spl mu/m regime

W/TiN gate CMOS technologies with improved performance were investigated using a damascene metal gate process. 0.1-/spl mu/m W/TiN stacked gate CMOS devices with high performance and good driving ability were fabricated successfully by optimizing the W/TiN stacked gate structure, improving the W/TiN gate electrode sputtering technology, and reducing W/TiN stacked gate MOSFET surface states and threshold voltages. A super steep retrograde (SSR) channel doping with heavy ion implantation, /sup 115/In/sup +/ for NMOS and /sup 121/Sb/sup +/ for PMOS, was applied here to obtain a reasonably lower threshold voltage and to suppress short-channel effects (SCEs). Non-CMP technology, used to replace CMP during the damascene metal gate process, was also explored. The propagation delay time of 57 stage W/TiN gate CMOS ring oscillators was 13 ps/stage at 3 V and 25 ps/stage at 1.5 V, respectively. Better performance would be achieved by using Co/Ti salicide source/drain (S/D) and thinner gate dielectrics.     

Improvement of threshold voltage deviation in damascene metal gatetransistors

The metal gate work function deviation (crystal orientation deviation) was found to cause the threshold voltage deviation (ΔV _th) in the damascene metal gate transistors. When the TiN work function (crystal orientation) is controlled by using the inorganic CVD technique, ΔV_th of the surface channel damascene metal gate (Al/TiN or W/TiN) transistors was drastically improved and found to be smaller than that for the conventional polysilicon gate transistors. The reason for the further reduction of the threshold voltage deviation (ΔV_th) in the damascene metal gate transistors is considered to be that the thermal-damages and plasma-damages on gate and gate oxide are minimized in the damascene gate process. High performance sub-100 nm metal oxide semiconductor field effect transistors (MOSFETs) with work-function-controlled CVD-TiN metal-gate and Ta₂O₅ gate insulator are demonstrated in order to confirm the compatibility with high-k gate dielectrics and the technical advantages of the inorganic CVD-TiN     

Large‐Area Schottky Barrier Transistors Based on Vertically Stacked Graphene–Metal Oxide Heterostructures

The fabrication of all‐transparent flexible vertical Schottky barrier (SB) transistors and logic gates based on graphene–metal oxide–metal heterostructures and ion gel gate dielectrics is demonstrated. The vertical SB transistor structure is formed by (i) vertically sandwiching a solution‐processed indium‐gallium‐zinc‐oxide (IGZO) semiconductor layer between graphene (source) and metallic (drain) electrodes and (ii) employing a separate coplanar gate electrode bridged with a vertical channel through an ion gel. The channel current is modulated by tuning the Schottky barrier height across the graphene–IGZO junction under an applied external gate bias. The ion gel gate dielectric with high specific capacitance enables modulation of the Schottky barrier height at the graphene–IGZO junction over 0.87 eV using a voltage below 2 V. The resulting vertical devices show high current densities (18.9 A cm^?2) and on–off current ratios (>10⁴) at low voltages. The simple structure of the unit transistor enables the successful fabrication of low‐power logic gates based on device assemblies, such as the NOT, NAND, and NOR gates, prepared on a flexible substrate. The facile, large‐area, and room‐temperature deposition of both semiconducting metal oxide and gate insulators integrates with transparent and flexible graphene opens up new opportunities for realizing graphene‐based future electronics.     

Fabrication of Schottky barrier MOSFETs using self-assembly CoSi2 nanopatterning and spacer gate technologies

A self-assembly patterning method for generation of epitaxial CoSi₂ nanostructures was used to fabricate 50 nm channel-length MOSFETs. The transistors have either a symmetric structure with Schottky source and drain or an asymmetric structure with n⁺-source and Schottky drain. The patterning technique is based on anisotropic diffusion of Co/Si atoms in a strain field during rapid thermal oxidation. The strain field is generated along the edges of a mask consisting of 20 nm SiO₂ and 300 nm Si₃N₄. During rapid thermal oxinitridation (RTON) of the masked silicide structure, a well-defined separation of the silicide layer forms along the edge of the mask. These highly uniform gaps define the channel region of the fabricated device. The separated silicide layers act as metal source and drain. A poly-Si spacer was used as the gate contact. The asymmetric transistor was fabricated by ion implantation into the unprotected CoSi₂ layer and a subsequent out-diffusion process to form the n⁺-source. I–V characteristics of both the symmetric and asymmetric transistor structures have been investigated.     

A high-performance polycrystalline silicon thin film transistorwith a silicon nitride gate insulator

We have fabricated a high performance polycrystalline silicon (poly-Si) thin film transistor (TFT) with a silicon-nitride (SiN_x ) gate insulator using three stacked layers: very thin laser of hydrogenated amorphous silicon (a-Si:H), SiN_x and laser annealed poly-Si. After patterning thin a-Si:H/SiN_x layers, gate, and source/drain regions were ion-doped and then Ni layer was deposited. This structure was annealed at 250°C to form a NiSi silicide phase. The low resistive Ni silicides were introduced as gate/source/drain electrodes in order to reduce the process steps. The poly-Si with a grain size of 250 nm and low resistance n⁺ poly-Si for ohmic contact were introduced to achieve a high performance TFT. The fabricated poly-Si TFT exhibited a field effect mobility of 262 cm²/Vs and a threshold voltage of 1 V     

Formation of TiSi2 and shallow junction byAs+ ion-beam mixing and infrared rapid heat treatment

A technique for forming shallow junctions with low-resistance silicide contacts developed for the use in VLSI with scaled MOSFETs is discussed. The salicide (self-aligned silicide) MOSFET gate and source-drain features self-aligned refractory metal silicide and are isolated from one another even without any insulating spacer on the gate sides. A critical step in such a MOSFET fabrication process is the ion implantation through metal silicidation technique, which includes As⁺ ion-beam-induced titanium-silicon interface mixing and infrared rapid heat treatment to form simultaneously the n⁺-p junction and a high-quality TiN covered TiSi₂ contact layer     

The observation of negative transconductance effect caused byreal-space-transfer of electrons in metal oxide semiconductor fieldeffect transistors fabricated with Ta2O5 gatedielectric

N-channel metal oxide semiconductor field effect transistors (MOSFETs) with Ta₂O₅ gate dielectric were fabricated. An intrinsic Ta₂O₅/silicon barrier height of 0.51 eV was extracted from the gate current. The effective Ta ₂O₅/silicon barrier height including image force barrier lowering is about 0.37 eV with drain to source voltage V_DS ranging from 1.5 V to 4.0 V. Due to the low barrier height, negative transconductance effect was observed in the linear region. The decrease of drain current is due to the real space transfer of electrons from the drain terminal to the gate electrode     

Transistor characteristics with Ta2O5 gatedielectric

As the gate oxide thickness decreases below 2 nm, the gate leakage current increases dramatically due to direct tunneling current. This large gate leakage current will be an obstacle to reducing gate oxide thickness for the high speed operation of future devices. A MOS transistor with Ta₂O₅ gate dielectric is fabricated and characterized as a possible replacement for MOS transistors with ultra-thin gate silicon dioxide. Mobility, I_d-V_d, I_d-V_g, gate leakage current, and capacitance-voltage (C-V) characteristics of Ta₂O₅ transistors are evaluated and compared with SiO₂ transistors. The gate leakage current is three to five orders smaller for Ta₂O₅ transistors than SiO₂ transistors     

A novel sacrificial gate stack process for suppression of boronpenetration in p-MOSFET with shallow BF2-implantedsource/drain extension

A novel process flow employing a sacrificial tetraethyl orthosilicate/polycrystalline silicon (TEOS/poly-Si) gate stack is proposed for fabricating fluorine-enhanced-boron-penetration-free p-channel metal oxide semiconductor field effect transistors (p-MOSFET's) with shallow BF₂-implanted source/drain (S/D) extension. With the presence of the sacrificial TEOS/poly-Si gate stack as the mask during the shallow BF₂ implant, the incorporated fluorine atoms are trapped in the sacrificial TEOS top layer and can be subsequently removed. The new process thus offers a unique opportunity of achieving an ultra shallow S/D extension characteristic of the BF₂ shallow implant, while not suffering from any fluorine-enhanced boron penetration normally accompanying the BF₂ implant. Excellent transistor performance with improved gate oxide integrity has been successfully demonstrated on p-MOSFET's fabricated with the new process flow     

A deep submicron Si1-xGex/Si vertical PMOSFETfabricated by Ge ion implantation

We report a deep submicron vertical PMOS transistor using strained Si_1-xGe_x channel formed by Ge ion implantation and solid phase epitaxy. These vertical structure Si_1-xGe_x /Si transistors can be fabricated with channel lengths below 0.2 μm without using any sophisticated lithographic techniques and with a regular MOS process. The enhancement of hole mobility in a direction normal to the growth plane of strained Si_1-xGe_x over that of bulk Si has been experimentally demonstrated for the first time using this vertical MOSFET. The drain current of these vertical MOS devices has been found to be enhanced by as much as 100% over control Si devices. The presence of the built-in electric field due to a graded SiGe channel has also been found to be effective in further enhancement of the drive current in implanted-channel MOSFET's     

High-speed enhancement-mode InP MISFET's grown by chloridevapor-phase epitaxy

The properties of enhancement-mode InP metal-insulator-semiconductor field-effect transistors fabricated on semi-insulating InP substrates are reported. The epitaxial layers of the device structure have been grown by chloride vapor-phase epitaxy. Short-circuit current gain cutoff frequencies of 29.6 GHz were measured for 1-μm-gate-length devices. For devices with submicrometer gate lengths, extrinsic transconductance values up to 300 mS/mm and short-circuit current-gain cutoff frequencies of 38.1 GHz were measured. SiO₂ deposited by electron beam evaporation and plasma-enhanced CVD Si₃N₄ have been utilized as gate insulators, and a drain current drift of 30% within the first 50 h of operation has been observed. The high-speed performance of these devices represent to the authors' knowledge the fastest InP-based MIS field-effect transistor demonstrated     

Novel dual-metal gate technology using Mo-MoSi/sub x/ combination

A novel dual-metal gate technology that uses a combination of Mo-MoSi/sub x/ gate electrodes is proposed. An amorphous-Si/Mo stack was fabricated as a gate electrode for the n-channel device. It was thermally annealed to form MoSi/sub x/. Pure Mo served as the gate electrode for the p-channel device. The work functions of MoSi/sub x/ and pure Mo gates on SiO/sub 2/ are 4.38 and 4.94 eV, respectively, which are appropriate for devices with advanced transistor structures. The small increase in the work function (< 20 meV) and the negligible equivalent oxide thickness variation (< 0.08 nm) after rapid thermal annealing at 950 /spl deg/C for 30 s also demonstrate the excellent thermal stabilities of Mo and MoSi/sub x/ on SiO/sub 2/. Additional arsenic ion implantation prior to silicidation was demonstrated further to lower the work function of MoSi/sub x/ to 4.07 eV. This approach for modulating the work function makes the proposed combination of Mo-MoSi/sub x/ gate electrodes appropriate for conventional bulk devices. The developed dual-metal-gate technology on HfO/sub 2/ gate dielectric was also evaluated. The effective work functions of pure Mo and undoped MoSi/sub x/ gates on HfO/sub 2/ are 4.89 and 4.34 eV, respectively. A considerable work-function shift was observed on the high-/spl kappa/ gate dielectric. The effect of arsenic preimplantation upon the work function of the metal silicide on HfO/sub 2/ was also demonstrated, even though the range of modulation was a little reduced.     

Ultralow-Thermal-Budget CMOS Process Using Flash-Lamp Annealing for 45 nm Metal/High- $k$ FETs

This paper describes a fabrication process that uses flash-lamp annealing (FLA) and the characteristics of the CMOS transistors that are constructed with an ultralow-thermal- budget process tuned for 45-nm metal/high-k FETs. FLA enhances the drivability of pFETs with the solid-phase epitaxial (SPE) extension junction, but reducing the thermal budget deteriorates the poly-gate depletion and the electron mobility. Metal gate, however, prevents the depletion problem and leads to higher drain currents and better threshold-voltage (V_TH) roll-offs when processed with tilted extension implantation combined with SPE + FLA than when processed with untilted extension implantation combined with spike rapid thermal annealing. Reducing the thermal budget is also effective in obtaining low V_TH values in p-metal/HfSiON gate because of the reduced vacancy formation. Moreover, cluster-boron implantation for pFETs has superiority over monomer-boron implantation with Ge postamorphous implantation in terms of V_TH roll-offs and I_on-I_off's if FLA is used as activation. The superior electrical characteristics of full-metal- gate HfSiON transistors whose gate length is less than 50 nm, which are fabricated by using the FLA process, are demonstrated.     

Characterizing Fluorine-Ion Implant Effects on Poly-Si Thin-Film Transistors With ${hbox{Pr}}_{2}{hbox{O}}_{3}$ Gate Dielectric

The fluorine ion implantation applied to the polycrystalline silicon thin-film transistors (poly-Si TFTs) with high-k Pr₂O₃ as gate dielectric is investigated for the first time. Using the Pr₂O₃ gate dielectric can obtain a high gate capacitance density and thin equivalent-oxide thickness, exhibiting a greatly enhancement in the driving capability of TFT device. Introducing fluorine ions into the poly-Si film by fluorine ion implantation technique can effectively passivate the trap states in the poly-Si film and at the Pr₂O₃/poly-Si interface to improve the device electrical properties. The Pr₂O₃ TFTs fabricated on fluorine-implanted poly-Si film exhibit significantly improved electrical performances, including lower threshold voltage, steeper subthreshold swing, higher field-effect mobility, lower off-state leakage current, and higher on/off current ratio, as compared with the control poly-Si Pr₂O₃ TFTs. Also, the incorporation of fluorine ions also improves the reliability of poly-Si Pr₂O₃ TFTs against hot-carrier stressing, which is attributed to the formation of stronger Si-F bonds. Furthermore, superior threshold-voltage rolloff characteristic is also demonstrated in the fluorine-implanted poly-Si Pr₂O₃ TFTs. Therefore, the proposed scheme is a promising technology for high-performance and high-reliability solid-phase crystallized poly-Si TFT.     

Source-field-plated Ga2O3 MOSFET with a breakdown voltage of 550 V

Ga_2O_3 metal–oxide–semiconductor field-effect transistors(MOSFETs) with high-breakdown characteristics were fabricated on a homoepitaxial n-typed β-Ga_2O_3 film, which was grown by metal organic chemical vapor deposition(MOCVD) on an Fedoped semi-insulating(010) Ga_2O_3 substrate. The structure consisted of a 400 nm unintentionally doped(UID) Ga_2O_3 buffer layer and an 80 nm Si-doped channel layer. A high k HfO_2 gate dielectric film formed by atomic layer deposition was employed to reduce the gate leakage. Moreover, a source-connected field plate was introduced to enhance the breakdown characteristics. The drain saturation current density of the fabricated device reached 101 mA/mm at V_gs of 3 V. The off-state current was as low as 7.1 ×10^-11 A/mm, and the drain current I_ON/I_OFF ratio reached 10~9. The transistors exhibited three-terminal off-state breakdown voltages of 450 and 550 V, corresponding to gate-to-drain spacing of 4 and 8 μm, respectively.     

A novel self-aligned bottom gate poly-Si TFT with in-situ LDD

A lithography independent self-aligned bottom gate thin film transistor (SABG-TFT) technology is proposed and experimentally demonstrated. The unique feature of the technology is the formation of self-aligned and symmetrical lightly doped source/drain (LDD) structure without any additional photolithographic or implantation steps. Thus, the number of masks used in the technology is the same as that in a conventional top gate TFT technology. Moreover, devices formed by the proposed method have thick source/drain and a thin channel region for providing low source/drain resistance and improved I-V characteristics. P-channel TFT devices are fabricated using a simple low temperature (⩽600°C) process. The fabricated SABG-TFT exhibits symmetrical transfer characteristics when the polarity of source/drain bias is reversed. The effective mobility and on-off current ratio of the devices are about 35 cm²/V-s and 6×10⁶ respectively     

Dual-metal gate CMOS technology with ultrathin silicon nitride gatedielectric

We report the first demonstration of a dual-metal gate complementary metal oxide semiconductor (CMOS) technology using titanium (Ti) and molybdenum (Mo) as the gate electrodes for the N-metal oxide semiconductor field effect transistors (N-MOSFETs) and P-metal oxide semiconductor field effect transistors (P-MOSFETs), respectively. The gate dielectric stack consists of a silicon oxy-nitride interfacial layer and a silicon nitride (Si₃N₄) dielectric layer formed by a rapid-thermal chemical vapor deposition (RTCVD) process. C-V characteristics show negligible gate depletion. Carrier mobilities comparable to that predicted by the universal mobility model for silicon dioxide (SiO₂) are observed     

A novel self-aligned poly-Si TFT with field-induced drain formed by the damascene Process

We have proposed and fabricated a self-aligned polysilicon thin-film transistor (poly-Si TFT) with a thick dielectric layer at the gate edges near the source and drain. A T-shaped polysilicon gate was successfully formed by the damascene process used in VLSI interconnection technology. During the on state, an inversion layer is induced by the subgate as a drain so that the on current is still high and the poly-Si region under the subgate behaves as an offset, reducing the off-state leakage current during the off-state. As the subgate dielectric becomes 3.5 times thicker than the main gate oxide, the minimum off-state leakage current of the new TFT is decreased from 1.4/spl times/10/sup -10/ to 1.3/spl times/10/sup -11/ without sacrifice of the on current. In addition, the on-off current ratio is significantly improved.     

Stable gallium arsenide MIS capacitors and MIS field effecttransistors by (NH4)2Sx treatment andhydrogenation using plasma deposited silicon nitride gate insulator

The beneficial effects of sulfur passivation of gallium arsenide (GaAs) surface by (NH₄)₂S_x chemical treatment and by hydrogenation of the insulator-GaAs interface using the plasma-enhanced chemical vapor-deposited (PECVD) silicon nitride gate dielectric film as the source of hydrogen are illustrated by fabricating Al/PECVD silicon nitride/n-GaAs MIS capacitors and metal insulator semiconductor field effect transistors (MISFET). Post metallization annealing (PMA) at temperatures in the range 450-550°C is shown to be the key process for achieving midgap interface state density below 10 ¹¹/cm²/eV and maximum incremental transconductance, which is about 75% of the theoretical maximum limit. MIS capacitors are fabricated on (NH₄)₂S_x treated GaAs substrate using gate dielectrics such as PECVD SiO ₂ and silicon oxynitride to demonstrate that the PMA is less effective with these dielectrics because of their lower hydrogen content. The small signal AC transconductance, g_ms measurements on MISFETs fabricated using silicon nitride, have shown that the low-frequency degradation of g_ms is almost absent in the devices fabricated on (NH₄)₂S_x-treated GaAs substrates and subjected to PMA. The drain current stability in these devices is demonstrated to be excellent, with an initial drift of only 2% of the starting value. The dual role of silicon nitride layer, namely, protection against loss of sulfur and an excellent source of hydrogen for additional surface passivation along with sulfur is demonstrated by comparing the transconductance of MISFETs fabricated on GaAs substrates annealed without the nitride cap after the (NH₄)₂S _x treatment