AZ31B镁合金表面火焰喷涂Al-Mg_2Si涂层的耐腐蚀性能

为提高AZ31B镁合金表面的耐腐蚀性能,用火焰喷涂方法在镁合金表面制备Al-Mg_2Si复合涂层。采用XRD、SEM和EDS分析涂层的物相组成、微观组织及元素分布;通过电化学试验测试样品在3.5%NaCl溶液中的腐蚀电位、腐蚀电流密度;通过3.5%NaCl溶液浸泡试验测试样品的腐蚀速率;并测试涂层的显微硬度。结果表明:涂层中的主要物相有Mg_2Si、Al,组织比较致密,元素分布均匀。Tafel极化曲线测试表明,Al-Mg_2Si涂层样品与AZ31B镁合金样品相比腐蚀电位从-1.489 V正移到-1.366 V,腐蚀电流密度从2.817×10~(-3) A/cm~2降低到1.198×10~(-3) A/cm~2。浸泡试验结果表明,喷涂Al-Mg_2Si的镁合金的腐蚀速率明显低于没有喷涂的镁合金。显微硬度测试表明,涂层的显微硬度集中分布在259~308 HV0.05之间,镁合金为50~60 HV0.05。因此在AZ31B镁合金表面火焰喷涂Al-Mg_2Si涂层可以提高其耐腐蚀性能,表面硬度显著提高。     

AZ31镁合金表面Al合金化层的制备与性能研究

为提高镁合金表面的耐蚀性,采用热喷涂技术在AZ31镁合金表面制备铝涂层,并利用脉冲钨极氩弧表面熔覆的方法进行表面重熔,获得富铝的合金化层,分析了合金化层的组织结构和性能。研究结果表明:在AZ31镁合金表面的铝合金化层中存在典型的树枝晶结构,含有金属间化合物Mg2Al3,Mg17Al12以及α-Mg和Al固溶体。显微硬度测试表明,铝合金化可使AZ31镁合金表面硬度由HV50左右提高到HV200左右。极化曲线测试表明,合金化层提高了镁合金表面的耐蚀性。     

镁合金表面等离子喷涂Al2O3-TiO2陶瓷涂层的耐腐蚀性研究

采用等离子喷涂技术在AZ31镁合金表面制备Al2O3-13％TiO2陶瓷复合涂层,对涂层的微观组织进行了观察分析,测试了涂层的表面硬度.通过极化曲线和浸泡腐蚀试验,对比研究了镁合金基材及喷涂陶瓷涂层的试样在5％ NaCl溶液中的耐腐蚀性能.结果表明:涂层镁合金试样的硬度和耐腐蚀性优于基体镁合金,但当腐蚀液透过涂层孔隙时...     

Al_2O_3含量对Al_2O_3-Al复合涂层组织和摩擦磨损性能的影响

通过改变喷涂粉末中Al2O3和Al的比例,在AZ91D镁合金表面制备不同Al2O3含量的等离子喷涂Al2O3-Al复合涂层。对复合涂层的显微组织、硬度和摩擦磨损性能进行表征,研究Al2O3含量对涂层组织和磨损性能的影响。结果表明,涂层组织为带状Al2O3分布在致密的Al基体上,Al2O3内可见细微的片层结构,且层与层间存在一定的孔隙。复合涂层中Al平均硬度62HV,Al2O3平均硬度达1380 HV。摩擦磨损实验证实,复合涂层具有较小的摩擦系数和较低磨损量,大大改善了镁合金表面的抗磨损性能。涂层中Al2O3体积少于Al时,Al2O3增加使涂层的抗磨效果增强。涂层中Al2O3体积超过Al后,涂层的孔隙增多、涂层变脆,其耐磨损性能下降。     

Mg3Sb2含量对Al-Mg3Sb2复相涂层耐磨性的影响

目的研究Mg_3Sb_2含量对Al-Mg_3Sb_2复相涂层的组织、硬度和摩擦学性能的影响,对比分析AZ31B镁合金基体、纯Al涂层和添加不同含量的Mg_3Sb_2之后涂层性能的差异。方法通过火焰喷涂技术在AZ31B镁合金表面制备了Al-Mg_3Sb_2复相涂层。利用扫描电镜(SEM)观察了涂层的截面形貌,利用X射线衍射仪(XRD)分析了涂层的物相组成。通过显微硬度计测试了AZ31B和涂层的硬度,通过摩擦磨损试验仪测试了AZ31B和涂层的摩擦学性能,并通过超景深三维显微镜测试了试样的磨痕宽度、深度及磨损体积。结果经火焰喷涂后可得到组织致密的复相涂层,涂层中的物相主要为Mg_3Sb_2和Al。涂层的平均硬度随Mg_3Sb_2含量的增加而增加,最高可达334.2HV0.025,是AZ31B的4.14倍。摩擦磨损试验中,涂层的摩擦系数随着Mg_3Sb_2含量的增加而减小,但都大于AZ31B的摩擦系数;涂层的磨损率随着Mg_3Sb_2含量的增加而减小,60%Mg_3Sb_2和80%Mg_3Sb_2涂层的磨损率小于AZ31B的磨损率,其他涂层的磨损率大于AZ31B的磨损率,80%Mg_3Sb_2涂层的耐磨性最好,比AZ31B下降了63.26%。随着Mg_3Sb_2含量的增加,Al-Mg_3Sb_2复相涂层的磨痕表面犁沟逐渐变浅并消失。结论 Mg_3Sb_2的加入可以提高涂层的硬度,随着其含量的增加,涂层的耐磨性逐渐提高。     

镁合金表面电子束熔覆铝涂层

为提高镁合金表面耐蚀性,采用火焰喷涂与高能电子束重熔技术在AZ91D镁合金表面制备了A1涂层.分析了涂层的微观组织结构和各区域的元素分布情况,测试了涂层硬度与耐蚀性.结果表明,在电子束重熔过程中,Al-Mg元素在涂层与基体间产生了明显的扩散,呈现交错的界面结合特征.涂层主要由熔覆区、合金化区和热影响区三部分组成,其中合金化层为典型的树枝晶结构.由于涂层中形成大量金属间化合物如Mg2Al3、Mg17Al12,使硬度由基体的70～80 HV0.05提高到220 HV0.05.这些相的存在也显著的提高了AZ91D镁合金表面的耐蚀性.     

AZ31B镁合金Al-AlB12-Al2O3涂层的耐蚀和耐磨性能北大核心CSCD

采用氧乙炔火焰喷涂方法,在AZ31B镁合金表面喷涂Al分别添加5%、10%、15%的(AlB_(12)+Al_2O_3)复合涂层,并对复合涂层进行热压处理;采用扫描电镜(SEM)观察复合涂层的微观组织,X射线衍射仪(XRD)检测涂层的物相,电化学工作站测试复合涂层的耐蚀性,显微硬度检测复合涂层的硬度,摩擦磨损机检测涂层的耐磨性能。结果表明:随着(AlB_(12)+Al_2O_3)含量的增加,复合涂层的孔隙率及孔洞减少,涂层致密;腐蚀电位从-1.5 V升高到-1.15 V,腐蚀电流从8.66×10^(-4)A/cm^2降到2.82×10^(-4)A/cm^2;硬度从66 HV增加到225 HV;磨痕也是从深到浅。综上所述,(AlB_(12)+Al_2O_3)复合涂层显著改善了镁合金的耐磨和耐蚀性能。     

AZ31B镁合金Al-AlB_(12)-Al_2O_3涂层的耐蚀和耐磨性能

采用氧乙炔火焰喷涂方法,在AZ31B镁合金表面喷涂Al分别添加5%、10%、15%的(AlB_(12)+Al_2O_3)复合涂层,并对复合涂层进行热压处理;采用扫描电镜(SEM)观察复合涂层的微观组织,X射线衍射仪(XRD)检测涂层的物相,电化学工作站测试复合涂层的耐蚀性,显微硬度检测复合涂层的硬度,摩擦磨损机检测涂层的耐磨性能。结果表明:随着(AlB_(12)+Al_2O_3)含量的增加,复合涂层的孔隙率及孔洞减少,涂层致密;腐蚀电位从-1.5 V升高到-1.15 V,腐蚀电流从8.66×10~(-4)A/cm~2降到2.82×10~(-4)A/cm~2;硬度从66 HV增加到225 HV;磨痕也是从深到浅。综上所述,(AlB_(12)+Al_2O_3)复合涂层显著改善了镁合金的耐磨和耐蚀性能。     

镁合金表面激光制备镍铝青铜涂层

利用激光熔覆的方法在AZ31B镁合金表面制备镍铝青铜涂层,采用扫描电镜、X射线衍射仪和显微硬度仪对涂层的微观形貌、物相以及显微硬度进行分析,采用PS–168A型电化学测量系统对涂层以及母材进行电化学腐蚀性能测试。结果表明,涂层内白色基体上析出富Cr的玫瑰状和块状的K相,涂层的物相主要由FeAl3、Al3Ni、Ni、Cu、Cr等组成,涂层的显微硬度最高可达602 HV0.2,较母材的50 HV0.2提高了约11倍,涂层的腐蚀电位?1.02 V较母材的?1.49 V提高了0.47 V。     

汽车发动机用AZ91合金表面喷涂与性能研究

采用等离子喷涂和激光重熔法在汽车发动机用AZ91合金表面制备了不同涂层,对比研究了涂层表面和横截面形貌、物相组成、显微硬度和电化学性能。结果表明,等离子喷涂层物相为:γ-Ni、FeNi_3、Ni_3B、WC、W_2C和Cr_7B_3,激光重熔层物相为γ-Ni、CrB、Ni_4B_3、WC、Cr_(23_B6和Cr_2B_3;显微硬度由高到低依次为:激光重熔层等离子喷涂层Ni/Al过渡层AZ91合金基材;等离子喷涂层和激光重熔层的耐腐蚀性能均高于AZ91合金基材,且激光重熔层的耐腐蚀性高于等离子喷涂层。     

Effects of Post-weld Heat Treatment on Microstructure,Mechanical Properties and the Role of Weld Reinforcement in 2219 Aluminum Alloy TIG-Welded Joints

In as-welded state, each region of 2219 aluminum alloy TIG-welded joint shows diff erent microstructure and microhardness due to the diff erent welding heat cycles and the resulting evolution of second phases. After the post-weld heat treatment, both the amount and the size of the eutectic structure or θ phases decreased. Correspondingly, both the Cu content in α-Al matrix and the microhardness increased to a similar level in each region of the joint, and the tensile strength of the entire joint was greatly improved. Post-weld heat treatment played the role of solid solution strengthening and aging strengthening. After the post-weld heat treatment, the weld performance became similar to other regions, but weld reinforcements lost their reinforcing eff ect on the weld and their existence was more of an adverse eff ect. The joint without weld reinforcements after the post-weld heat treatment had the optimal tensile properties, and the specimens randomly crack in the weld zone.     

The First Phase of the SRIF Industrialized Base in ＂West Area＂ Has Been Put into Operation

After nearly two years＇ tense construction, the first phase of industrialized base of Shenyang Research Institute of Foundry （SRIF）, located at the Tiexi Casting and Forging Industrial Park in the west of Tiexi District, has now been completed and formally put into operation.     

Thermodynamics Study on the Decomposition of Chromite with KOH

Institute of Process Engineering, Chinese Academy of Sciences, China, has proposed a method for oxidative leaching of chromite with potassium hydroxide. Understanding the mechanism of chromite decomposition, especially in the potassium hydroxide fusion, is important for the optimization of the operating parameters of the oxidative leaching process. A traditional thermodynamic method is proposed and the thermal decomposition and the reaction decomposition during the oxidative leaching of chromite with KOH and oxygen is discussed, which suggests that chromite is mainly destroyed by reactions with KOH and oxygen. Meanwhile, equilibrium of the main reactions of the above process was calculated at different temperatures and oxygen partial pressures. The stable zones of productions, namely, K2CrO4 and Fe2O3, increase with the decrease of temperature, which indicates that higher temperature is not beneficial to thermodynamic reactions. In addition, a comparison of the general alkali methods is carried out, and it is concluded that the KOH leaching process is thermodynamically superior to the conventional chromate production process.     

Influence of Heat Treatment on Damping Behaviour of the Magnesium Wrought Alloy AZ61

The effect of isochronal heat treatments for 1h on variation of damping, hardness and microstructural change of the magnesium wrought alloy AZ61 was investigated. Damping and hardness behaviour could be attributed to the evolution of precipitation process. The influence of precipitation on damping behaviour was explained in the framework of the dislocation string model of Granato and Lücke.     

Effect of Rare Earth Doping on Impedance,Modulus and Conductivity Properties of Multiferroic Composites:0.5(BiLa_xFe_(1-x)O_3)–0.5(PbTiO_3)

The Lanthanum-doped bismuth ferrite–lead titanate compositions of 0.5(Bi LaxFe1-xO3)–0.5(Pb Ti O3)(x = 0.05,0.10,0.15,0.20)(BLxF1-x-PT) were prepared by mixed oxide method.Structural characterization was performed by X-ray diffraction and shows a tetragonal structure at room temperature.The lattice parameter c/a ratio decreases with increasing of La(x = 0.05–0.20) concentration of the composites.The effect of charge carrier/ion hopping mechanism,conductivity,relaxation process and impedance parameters was studied using an impedance analyzer in a wide frequency range(102–106Hz) at different temperatures.The nature of Nyquist plot confirms the presence of bulk effects only,and non-Debye type of relaxation processes occurs in the composites.The electrical modulus exhibits an important role of the hopping mechanism in the electrical transport process of the materials.The ac conductivity and dc conductivity of the materials were studied,and the activation energy found to be 0.81,0.77,0.76 and 0.74 e V for all compositions of x = 0.05–0.20 at different temperatures(200–300 °C).     

Quantitative Analysis of the Crystallographic Orientation Relationship Between the Martensite and Austenite in Quenching–Partitioning–Tempering Steels

The orientation relationships(ORs)between the martensite and the retained austenite in low-and medium-carbon steels after quenching–partitioning–tempering process were studied in this work.The ORs in the studied steels are identified by selected-area electron diffraction(SAED)as either K–S or N–W ORs.Meanwhile,the ORs were also studied based on numerical fitting of electron backscatter diffraction data method suggested by Miyamoto.The simulated K–S and N–W ORs in the low-index directions generally do not well coincide with the experimental pole figure,which may be attributed to both the orientation spread from the ideal variant orientations and high symmetry of the low-index directions.However,the simulated results coincide well with experimental pole figures in the high-index directions{123}_(bcc).A modified method with simplicity based on Miyamoto’s work was proposed.The results indicate that the ORs determined by modified method are similar to those determined by Miyamoto’method,that is,the OR is near K–S OR for the low-carbon Q–P–T steel,and with the increase of carbon content,the OR is closer to N–W OR in medium-carbon Q–P–T steel.     

Using Finite Element and Contour Method to Evaluate Residual Stress in Thick Ti-6Al-4V Alloy Welded by Electron Beam Welding

This work was to reveal the residual stress profile in electron beam welded Ti-6Al-4V alloy plates(50 mm thick) by using finite element and contour measurement methods.A three-dimensional finite element model of 50-mmthick titanium component was proposed,in which a column–cone combined heat source model was used to simulate the temperature field and a thermo-elastic–plastic model to analyze residual stress in a weld joint based on ABAQUS software.Considering the uncertainty of welding simulation,the computation was calibrated by experimental data of contour measurement method.Both test and simulated results show that residual stresses on the surface and inside the weld zone are significantly different and present a narrow and large gradient feature in the weld joint.The peak tensile stress exceeds the yield strength of base materials inside weld,which are distinctly different from residual stress of the thin Ti-6Al-4V alloy plates presented in references before.     

Microstructures and Tensile Properties of Ultrafine-Grained Ni–(1–3.5) wt% SiC_(NP) Composites Prepared by a Powder Metallurgy Route

Silicon carbide nanoparticle-reinforced nickel-based composites(Ni–Si CNP),with a Si CNPcontent ranged from1 to 3.5 wt%,were prepared using mechanical alloying and spark plasma sintering.In addition,unreinforced pure nickel samples were also prepared for comparative purposes.To characterize the microstructural properties of both the unreinforced pure nickel and the Ni–Si CNPcomposites transmission electron microscopy(TEM) was used,while their mechanical behavior was investigated using the Vickers pyramid method for hardness measurements and a universal tensile testing machine for tensile tests.TEM results showed an array of dislocation lines decorated in the sintered pure nickel sample,whereas,for the Ni–Si CNPcomposites,the presence of nano-dispersed Si CNPand twinning crystals was observed.These homogeneously distributed Si CNPwere found located either within the matrix,between twins or on grain boundaries.For the Ni–Si CNPcomposites,coerced coarsening of the Si CNPassembly occurred with increasing Si CNPcontent.Furthermore,the grain sizes of the Ni–Si CNPcomposites were much finer than that of the unreinforced pure nickel,which was considered to be due to the composite ball milling process.In all cases,the Ni–Si CNPcomposites showed higher strengths and hardness values than the unreinforced pure nickel,likely due to a combination of dispersion strengthening(Orowan effects) and particle strengthening(Hall–Petch effects).For the Ni–Si CNPcomposites,the strength increased initially and then decreased as a function of Si CNPcontent,whereas their elongation percentages decreased linearly.Compared to all materials tested,the Ni–Si CNPcomposite containing 1.5% Si C was found more superior considering both their strength and plastic properties.     

Directional Growth of Tin Crystals Controlled by Combined Solute Concentration Gradient Field and Static Magnetic Field

A new method was introduced to achieve directional growth of Sn crystals. Microstructures in liquid(Pb)/liquid(Sn) diffusion couples were investigated under various static magnetic fields. Results show that the β-Sn crystals mainly reveal an irregular dendritic morphology without or with a relatively low static magnetic field(B0.3 T). When the magnetic field is increased to 0.5 T, the β-Sn dendrites close to the final stage of growth begin to show some directional character. With a further increase in the magnetic field to a higher level(0.8–5 T), the β-Sn dendrites have an enhanced directional growth character, but the dendrites show a certain deflection. As the magnetic field is increased to 12 T, the directional growth of the β-Sn dendrites in the center of the couple is severely destroyed. The mechanism of the directional growth of the β-Sn crystals and the deflection of the β-Sn crystals with the application of static magnetic field was tentatively discussed.     

电化学噪声数据处理方法概述

综述了常见的电化学噪声数据处理方法,介绍了直流趋势剔除、统计分析、快速傅立叶变换(FFT)法计算功率谱密度(PSD)以及小波变换处理电化学噪声信号的基本过程,并阐释了各种数学处理及所得参数的物理意义。