Highly mesoporous carbonaceous material of activated carbon beads for electric double layer capacitor

The activated carbon beads (ACB) are prepared by a new preparation method, which is proposed by mixing the coal tar pitch and fumed silica powder at a certain weight ratio and activation by KOH at different weight ratios and different temperatures. The BET surface area, pore volume and average pore size are obtained based on the nitrogen adsorption isotherms at 77 K by using ASAP 2010 apparatus. The results show that our samples have much high specific surface area (SSA) of 3537 m² g⁻¹and high pore volume value of 3.05 cm³ g⁻¹. The percentage of mesopore volume increases with the weight ratio of KOH/ACB ranging from 4% to 72%. The electrochemical double layer capacitors (EDLCs) are assembled with resultant carbon electrode and electrolyte of 1 mol L⁻¹ Et₄NBF₄/PC. The specific capacitance of the ACB sample could be as high as 191.7 F g⁻¹ by constant current charge/discharge technique, indicating that the ACB presents good characteristics prepared by the method proposed in this work. The investigation of influence of carbon porosity structure on capacitance indicates that the SSA plays an important role on the capacitance and all the pore sizes of less than 1 nm, from 1 to 2 nm and larger than 2 nm contribute to the capacitance. Mesopore structure is beneficial for the performance at high current density.     

Influence of carbon sources on LiFePO4/C composites synthesized by the high-temperature high-energy ball milling method

Carbon-coated LiFePO₄ composites were synthesized by a new method of high-temperature high-energy ball milling (HTHEBM). Fe₂O₃ and LiH₂PO₄ were used as raw materials. Glucose, sucrose, citric acid and active carbon were used as reducing agents and carbon sources, respectively. In this method, high-energy ball milling and carbon coating worked together and, therefore, fine and homogeneous LiFePO₄/C particles with excellent properties were obtained in a relatively short synthesis time of 9 h. Moreover, the synthesis process could be completely finished at a relatively lower temperature of 600 °C for high-energy ball milling transforming mechanical energy into thermal energy. The results of X-ray diffraction (XRD) analysis, scanning electron microscopy (SEM), transmission electron microscopy (TEM) and electrochemical performance tests indicated that carbon source had an important influence on the properties of LiFePO₄/C composites synthesized by the HTHEBM method. It was proved that the LiFePO₄ composites coated with glucose had the best properties with 1 μm geometric mean diameter and 150.3 mA h g⁻¹ initial discharge capacity at a current rate of 0.1 C. After the 20th cycle test, the reversible capacity was 148 mA h g⁻¹ at 0.1 C, showing a retention ratio to the initial capacity of 98.5%.     

Development of an electrochemical ascorbic acid sensor based on the incorporation of a ferricyanide mediator with a polyelectrolyte-calcium carbonate microsphere

A novel electro-active material was successfully prepared with Fe(CN)₆³⁻ ions loaded by electrostatic interaction onto the layer of poly(allylamine) hydrochloride (PAH), which was first assembled on prepared poly(sodium 4-styrenesulfonate) (PSS)-doped porous calcium carbonate (CaCO₃) microspheres. Further, an electrochemical sensor for use in ascorbic acid (AA) detection was constructed with the use of the above electro-active materials embedded into a chitosan (CS) sol-gel matrix as an electron mediator. The electrocatalytic oxidation of AA by ferricyanide was observed at the potential of 0.27 V, which was negative-shifted compared with that by direct electrochemical oxidation of AA on a glassy carbon electrode. The experimental parameters, including the pH value of testing solution and the applied potential for detection of AA, were optimized. The current electrochemical sensor not only exhibited a good reproducibility and storage stability, but also showed a fast amperometric response to AA in a linear range (1.0 × 10⁻⁶ to 2.143 × 10⁻³ M), a low detection limit (7.0 × 10⁻⁷ M), a fast response time (<6 s), and a high sensitivity (−4.5127 μA mM⁻¹).     

Synthesis and characterization of high-density LiFePO4/C composites as cathode materials for lithium-ion batteries

To achieve a high-energy-density lithium electrode, high-density LiFePO₄/C composite cathode material for a lithium-ion battery was synthesized using self-produced high-density FePO₄ as a precursor, glucose as a C source, and Li₂CO₃ as a Li source, in a pipe furnace under an atmosphere of 5% H₂-95% N₂. The structure of the synthesized material was analyzed and characterized by X-ray diffraction (XRD) and scanning electron microscope (SEM). The electrochemical properties of the synthesized LiFePO₄/carbon composite were investigated by cyclic voltammetry (CV) and the charge/discharge process. The tap-density of the synthesized LiFePO₄/carbon composite powder with a carbon content of 7% reached 1.80 g m⁻³. The charge/discharge tests show that the cathode material has initial charge/discharge capacities of 190.5 and 167.0 mAh g⁻¹, respectively, with a volume capacity of 300.6 mAh cm⁻³, at a 0.1C rate. At a rate of 5C, the LiFePO₄/carbon composite shows a high discharge capacity of 98.3 mAh g⁻¹ and a volume capacity of 176.94 mAh cm⁻³.     

Preparation and characterization of carbon-coated LiFePO4 cathode materials for lithium-ion batteries with resorcinol-formaldehyde polymer as carbon precursor

LiFePO₄/C composites were synthesized by two methods using home-made amorphous nano-FePO₄ as the iron precursor and soluble starch, sucrose, citric acid, and resorcinol-formaldehyde (RF) polymer as four carbon precursors, respectively. The crystalline structures, morphologies, compositions, electrochemical performances of the prepared powders were investigated with XRD, TEM, Raman, and cyclic voltammogram method. The results showed that employing soluble starch and sucrose as the carbon precursors resulted in a deficient carbon coating on the surface of LiFePO₄ particle, but employing citric acid and RF polymer as the carbon precursors realized a uniform carbon coating on the surface of LiFePO₄ particle, and the corresponding thicknesses of the uniform carbon films are 2.5 nm and 4.5 nm, respectively. When RF polymer was used as the carbon precursor, the material showed the highest initial discharge capacity (138.4 mAh g^− 1 at 0.2 C at room temperature) and the best rate performance among the four materials.     

Carbon coated Li3V2(PO4)3 cathode material prepared by a PVA assisted sol-gel method

Carbon coated Li₃V₂(PO₄)₃ cathode material was prepared by a poly(vinyl alcohol) (PVA) assisted sol-gel method. PVA was used both as the gelating agent and the carbon source. XRD analysis showed that the material was well crystallized. The particle size of the material was ranged between 200 and 500 nm. HRTEM revealed that the material was covered by a uniform surface carbon layer with a thickness of 80 Å. The existence of surface carbon layer was further confirmed by Raman scattering. The electrochemical properties of the material were investigated by charge-discharge cycling, CV and EIS techniques. The material showed good cycling performance, which had a reversible discharge capacity of 100 mAh g⁻¹ when cycled at 1 C rate. The apparent Li⁺ diffusion coefficients of the material ranged between 9.5 × 10⁻¹⁰ and 0.9 × 10⁻¹⁰ cm² s⁻¹, which were larger than those of olivine LiFePO₄. The large lithium diffusion coefficient of Li₃V₂(PO₄)₃ has been attributed to its special NASICON-type structure.     

Preparation, electrochemical behavior and performance of gallium hexacyanoferrate as electrocatalyst of H2O2

The gallium hexacyanoferrate (GaHCF) was synthesized chemically and characterized by FTIR technique. Its electrochemical behavior was carefully investigated by fabricating a GaHCF modified carbon paste electrode in various supporting electrolyte. The experimental results showed that in KNO₃, K₂SO₄, KCl and other supporting electrolyte, GaHCF yielded one pair of ill-defined redox waves with a formal potential of 0.9 V (versus SCE). In 0.050 mol L⁻¹ phosphate buffer solution (PBS, pH 6.8), however, GaHCF yielded one pair of well-defined redox peaks with a formal potential of 0.222 V. Furthermore, this modified electrode exhibited a high electrocatalytic activity toward the reduction of H₂O₂ in pH 6.8 PBS, with over-potential dramatically lower than that of on the bare carbon paste electrode. Amperometry was used for the determination of H₂O₂, under the optimal conditions, a linear dependence of the catalytic current versus H₂O₂ concentration was obtained in the range of 4.9 × 10⁻⁶ to 4.0 × 10⁻⁴ mol L⁻¹ with a detection limit of 1 × 10⁻⁶ mol L⁻¹ when the signal-to-noise ratio was 3, and a sensitivity of 27.9 μA mM⁻¹ (correlation coefficient of 0.997). Chronoamperometry was used to conveniently determine the diffusion coefficient of H₂O₂ in the solution.     

Role of pH-regulation in lactic acid fermentation: Second steps in a process improvement

Lactic acid has versatile application in chemical industries and it can be economically produced from biomass resources, for example from sweet sorghum juice, containing easily fermentable sugars in high concentration (150-180 gL⁻¹). To neutralize the produced lactic acid, alkali addition (i.e., titration) or pH buffering was applied to avoid the inhibitory effect of the undissociated lactic acid. However, such a high concentration of ionized lactate also inhibits the growth and further production. Our task was to find an appropriate pH regulation method and to describe pH dependency of the used strain. Five pH regulation agents were tested and among them trimethylamine gave the best productivity result (3.13 gL⁻¹ h⁻¹), but considering technological aspects (such as dilution) ammonium hydroxide is also recommended. Titration by NH₄OH and buffering by CaCO₃ were compared, and then combined, resulted in very good productivity (3.55 gL⁻¹ h⁻¹). pH dependence of the used strain was also examined and the optimal pH value was between 6.8 and 7.0.     

Enhanced electrochemical properties of LiFePO4/C synthesized with two kinds of carbon sources,PEG-4000 (organic) and Super p (inorganic)

Olivine structured LiFePO₄/C cathode was synthesized via a freeze-drying route and followed by microwave heating with two kinds of carbon sources: PEG-4000 (organic) and Super p (inorganic). XRD patterns indicate that the as-prepared sample has an olivine structure and carbon modification does not affect the structure of the sample. Image of SEM shows a uniform and optimized particles size, which greatly improves the electrochemical properties. TEM result reveals the amorphous carbon around the surface of the particles. At a low rate of 0.1 C, the LiFePO₄/C sample presents a high discharge capacity of 157.8 mAh g⁻¹ which is near the theoretical capacity (170 mAh g⁻¹), and it still attains to 149.1 mAh g⁻¹ after 200 cycles. It also exhibits an excellent rate capacity with high discharge capacities of 143.2 mAh g⁻¹, 137.5 mAh g⁻¹, 123.7 mAh g⁻¹ and 101.6 mAh g⁻¹ at 0.5 C, 1.0 C, 2.0 C and 5.0 C, respectively. EIS results indicate that the charge transfer resistance of LiFePO₄ decreases greatly after carbon coating.     

Modification of macroporous stainless steel supports with silica nanoparticles for size selective carbon membranes with improved flux

Silica nanoparticles were slip cast into porous stainless steel supports, which were then coated with polyfurfuryl alcohol and pyrolyzed to make nanoporous carbon membranes. The single gas permeances of the membranes formed on modified stainless steel supports were found to be between two and three orders of magnitude larger than the permeances of nanoporous carbon membranes (<10⁻¹¹ mol m⁻² s⁻¹ Pa⁻¹) synthesized on unmodified supports. Importantly, these high permeances (10⁻⁸-10⁻⁹ mol m⁻² s⁻¹ Pa⁻¹) were achieved within the same range of O₂/N₂ selectivities (3-5) that we have observed for single gases permeating at much lower fluxes through the nanoporous carbon membranes on unmodified supports. The nanoporous carbon membranes also were formed by combining the silica nanoparticles with polyfurfuryl alcohol resin and applying the mixture directly onto an unmodified support. This simpler process was as effective in producing selective-high permeance membranes. In both cases the significant increase in permeance without loss of selectivity is attributed to the silica nanoparticles filling the macropores of the stainless steel supports, thereby leading to the formation of very thin but selective carbon layers.     

Improved capacitance characteristics during electrochemical charging of carbon nanotubes modified with polyoxometallate monolayers

By modification of surfaces of multi-walled carbon nanotubes with ultra-thin monolayer-type films of phosphododecamolybdic acid, H₃PMo₁₂O₄₀, an electrode material with improved capacitance properties is produced. It is apparent from three distinct test experiments (based on cyclic voltammetry, galavanostatic charging-discharging and AC impedance) that capacitors utilizing H₃PMo₁₂O₄₀-modified carbon nanotubes are characterized by specific capacitances and energy densities on the levels of 40 F g⁻¹ and 1.3 Wh kg⁻¹, whereas the respective values for the systems built from bare carbon nanotubes are lower, 22 F g⁻¹ and 0.7 Wh kg⁻¹. It is reasonable to expect that fast and reversible multi-electron transfers of the Keggin-type H₃PMo₁₂O₄₀ account for the pseudocapacitance effect and significantly contribute to the observed overall capacitance.     

Kinetics of ethanol oxidation in subcritical water

Ethanol oxidation in subcritical water was examined at 25 MPa in the temperature range of 260-350 °C with equivalence ratio of 0.6. With oxygen as the oxidiser, the overall first-order decomposition reaction parameters were determined to be 10^2.9 ± 0.4 s⁻¹ for the pre-exponential factor and 53.8 ± 4.6 kJ mol⁻¹ for the activation energy. The products obtained by the hydrothermal oxidation of ethanol were acetaldehyde, acetic acid, carbon monoxide and carbon dioxide. First-order kinetics was enough to capture the main characteristics of species concentration profiles. Consecutive reaction network: C₂H₅OH → CH₃CHO → CH₃COOH → CO → CO₂ well described the behaviour of components obtained from wet oxidation of ethanol.     

European inter-laboratory comparison of high pressure CO2 sorption isotherms. I: Activated carbon

In order to assess and improve the quality of high-pressure sorption isotherms of carbon dioxide (CO₂) on coals, an inter-laboratory study (“Round Robin”) has been conducted among four European research laboratories. In a first round of measurements, excess sorption isotherms were determined on Filtrasorb 400 (F400) activated carbon at 318 K using the manometric (TU Delft and RWTH Aachen University) and the gravimetric (FP Mons and INERIS) method up to 16 MPa. The study shows that CO₂ sorption in the supercritical range can be determined accurately with both gravimetric and manometric equipment but requires thorough optimization of instrumentation and measuring as well as proper sample preparation procedures. For the characterization of the activated carbon F400, which we used as benchmark, we have determined a surface area of 1063 m² g⁻¹, and Dubinin-Radushkevich (DR) micropore volume of 0.51 cm³ g⁻¹. Additionally, we analysed the elementary near-surface composition by energy dispersive X-ray spectroscopy (EDX). To characterise the bulk composition of the F400 activated carbon, a proximate and ultimate analysis was performed.The observed excess sorption maxima around 5 MPa have values around 8.0 mol kg⁻¹, which are consistently higher (by upto 0.8 mol kg⁻¹) than literature data.     

Methane reforming reaction with carbon dioxide over SBA-15 supported Ni-Mo bimetallic catalysts

A series of mesoporous molecular sieves SBA-15 supported Ni-Mo bimetallic catalysts (xMo1Ni, Ni = 12 wt.%, Mo/Ni atomic ratio = x, x = 0, 0.3, 0.5, 0.7) were prepared using co-impregnation method for carbon dioxide reforming of methane. The catalytic performance of these catalysts was investigated at 800 °C, atmospheric pressure, GHSV of 4000 ml·g_cat^− 1·h^− 1 and a V(CH₄)/(CO₂) ratio of 1 without dilute gas. The result indicated that the Ni-Mo bimetallic catalysts had a little lower initial activity compared with Ni monometallic catalyst, but it kept very stable performance under the reaction conditions. In addition, the Ni-Mo bimetallic catalyst with Mo/Ni atomic ratio of 0.5 showed high activity, superior stability and the lowest carbon deposition rate (0.00073g_c·g_cat^− 1·h^− 1) in 600-h time on stream. The catalysts were characterized by power X-ray diffraction, N₂-physisorption, H₂-TPR, CO₂-TPD, TG and TEM. The results indicate that the Ni-Mo bimetallic catalysts have smaller metal particle, higher metal dispersion, stronger basicity, metal-support interaction and Mo₂C species. It is concluded that Mo species in the Ni-Mo bimetallic catalysts play important roles in reducing effectively the amount of carbon deposition, especially the amount of shell-like carbon deposition.     

A glassy carbon supported bilayer lipid-like membrane of 5,5-ditetradecyl-2-(2-trimethyl-ammonioethyl)-1,3-dioxane bromide for electrochemical sensing of epinephrine

A self-assembled bilayer lipid-like membrane (BLM) supported on glassy carbon electrode (GCE) was fabricated using 5,5-ditetradecyl-2-(2-trimethyl-ammonioethyl)-1,3-dioxane bromide (DTDB) for epinephrine (EP) determination in the presence of ascorbic acid (AA). This modified electrode (DTDB/GCE) has strong membrane adsorption accumulation and electrocatalytic ability toward EP and AA. The oxidation of EP was controlled by double step adsorption accumulation process of the DTDB-BLM. The parameters of fitted Langmuir isotherm Γ_max, B_ADS, and ΔG_ADS values were determined as 1.0×10⁻¹¹ mol cm⁻², 2.04×10⁶ dm³ mol⁻¹, and −45.17 kJ mol⁻¹ for the fist step for EP concentration less than 1 mM, and 4.92×10⁻¹¹ mol cm⁻², 7.35×10⁴ dm³ mol⁻¹, and −37.1 kJ mol⁻¹ for the second step for EP concentration higher than 1 μM. The DPV peaks for EP and AA oxidations were appeared at 0.220 and 0.085 V versus SCE, respectively, allowing the determination of EP in the presence of high concentration of AA. The advantage of DTDB-BLM was demonstrated experimentally in comparison with other three BLMs, and attributed to the dioxane group as well as the suitable length of the carbon chain of DTDB molecule. The current response of the DTDB/GCE was fast and reproducible, suitable for the electrochemical sensing in flow-injection systems. A linear range of 1×10⁻⁸ to 1×10⁻⁴ M EP was preliminary obtained using a simple setup.     

Synthesis, characterization and electroanalytical application of a new SiO2/SnO2 carbon ceramic electrode

A new SiO₂/SnO₂ carbon ceramic composite was prepared by the sol-gel method, and its potential application in electrochemistry as a novel electrode material has been studied. The prepared xerogel was structurally and electrochemically characterized by scanning electron microscopy coupled to energy dispersive spectroscopy, X-ray photoelectron spectroscopy, X-ray diffraction and cyclic voltammetry. The composite was pressed in a rigid disk-shape and used as a conductive substrate to immobilize a water-soluble organic-inorganic hybrid polymer, 3-n-propyl-4-picolinium chloride silsesquioxane. The oxidation of nitrite was studied on this polymer film coated electrode in aqueous solution using cyclic voltammetry and differential pulse voltammetry. This modified electrode exhibited a better defined voltammetric peak shifted negatively about 60 mV. The linear detection limit found for nitrite was from 1.3 × 10⁻⁵ to 1.3 × 10⁻³ mol l⁻¹ and the detection limit was 3.3 × 10⁻⁶ mol l⁻¹.     

Characterisation of activated nanoporous carbon for supercapacitor electrode materials

Commercial nanoporous carbon RP-20 was activated with water vapor in the temperature range from 950 °C to 1150 °C. The XRD analysis was carried out on nanoporous carbon powder samples to investigate the structural changes (graphitisation) in modified carbon that occurred at activation temperatures T ? 1150 °C. The first-order Raman spectra showed the absorption peak at 1582 cm⁻¹ and the disorder (D) peak at 1350 cm⁻¹. The low-temperature N₂ adsorption experiments were performed at −196 °C and a specific surface area up to 2240 m²g⁻¹ for carbon activated at T = 1050 °C was measured. The cell capacitance for two electrode activated nanoporous carbon system advanced up to 60 F g⁻¹ giving the specific capacitance ∼240 F g⁻¹ to one electrode nanoporous carbon ∣1.2 M (C₂H₅)₃CH₃NBF₄ + acetonitrile solution interface. A very wide region of ideal polarisability for two electrode system (∼3.2 V) was achieved. The low frequency limiting specific capacitance very weakly increases with the rise of specific area explained by the mass transfer limitations in the nanoporous carbon electrodes. The electrochemical characteristics obtained show that some of these materials under discussion can be used for compilation of high energy density and power density non-aqueous electrolyte supercapacitors with higher power densities than aqueous supercapacitors.     

An optimized Ni doped LiFePO4/C nanocomposite with excellent rate performance

Both Ni doping and carbon coating are adopted to synthesize a nano-sized LiFePO₄ cathode material through a simple solid-state reaction. It is found that the Ni²⁺ has been successfully doped into LiFePO₄ without affecting the phospho-olivine structure from the XRD result. The images of SEM and TEM show that the size of particles is distributed in the range of 20-60 nm, and all the particles are coated with carbon completely. The results of XPS show the valence state of Fe and Ni in the LiFePO₄. The electronic conductivity of the material is as high as 2.1 × 10⁻¹ S cm⁻¹, which should be ascribed to the coefficient of the conductive carbon network and Ni doping. As a cathode material for lithium-ion batteries, the Ni doped LiFePO₄/C nanocomposite delivers a discharge capacity of 170 mAh g⁻¹ at 0.2 C, approaching the theoretical value. Moreover, the material shows excellent high-rate charge and discharge capability and long-term cyclability. At the high rates of 10 and 15 C, this material exhibits high capacities of 150 and 130 mAh g⁻¹, retaining 95% after 5500 cycles and 93% after 7200 cycles, respectively. Therefore, the as-prepared material is capable of such large-scale applications as electric vehicles and plug-in hybrid electric vehicles.     

Micromolar determination of sulfur oxoanions and sulfide at a renewable sol-gel carbon ceramic electrode modified with nickel powder

The sol-gel technique was used to fabricate nickel powder carbon composite electrode (CCE). The nickel powder successfully used to deposit NiO_x thin film on conductive carbon ceramic electrode for large surface area catalytic application. Repetitive cycling in potential range −0.2 to 1.0 V was used to form of a thin nickel oxide film on the surface carbon composite electrode. The thin film exhibits an excellent electro-catalytic activity for oxidation of SO₃²⁻, S₂O₄²⁻, S₂O₃²⁻, S₄O₆²⁻ and S²⁻ in alkaline pH range 10-14. Optimum pH values for detection of all sulfur derivatives is 13 and catalytic rate constants are in range 2.4 × 10³-8.9 × 10³ M⁻¹ s⁻¹. The hydrodynamic amperometry at rotating modified CCE at constant potential versus reference electrode was used for detection of sulfur derivatives. Under optimized conditions the calibration plots are linear in the concentration range 10 μM-15 mM and detection limit 1.2-34 μM and 0.53-7.58 nA/μM (sensitivity) for electrode surface area 0.0314 cm². The nickel powder doped modified carbon ceramic electrode shows good reproducibility, a short response time (2.0 s), remarkable long term stability, less expense, simplicity of preparation, good chemical and mechanical stability, and especially good surface renewability by simple mechanical polishing and repetitive potential cycling. This sensor can be used into the design of a simple and cheap chromatographic amperometry detector for analysis of sulfur derivatives.     

Electrooxidation of sulfide by cobalt pentacyanonitrosylferrate film on glassy carbon electrode by cyclic voltammetry

A glassy carbon (GC) electrode was modified with cobalt pentacyanonitrosylferrate (CoPCNF) film. Cyclic voltammetry (CV) of the CoPCNF onto the GC (CoPCNF/GC) shows a redox couple (Fe^III/Fe^II) with a standard potential (E^0′) of 580 mV. The current ratio I_pa/I_pc remains almost 1, and a peak separation (ΔE_p) of 106 mV is observed in 0.5 M KNO₃ as the supporting electrolyte. Anodic peak currents were found to be linearly proportional to the scan rate between 10 and 200 mV s⁻¹, indicating an adsorption-controlled process. The redox couple of the CoPCNF film presents an electrocatalytic response to sulfide in aqueous solution. The analytical curve was linear in the concentration range of 7.5 × 10⁻⁵ to 7.7 × 10⁻⁴ M with a detection limit of 4.6 × 10⁻⁵ M for sulfide ions in 0.5 M KNO₃ solution.