6005A铝合金挤压型材搅拌摩擦焊接头的疲劳性能

对6005A-T6铝合金挤压型材进行焊速为1000 mm/min的搅拌摩擦高焊速焊接,研究了对接面机械打磨对接头组织和力学性能的影响.结果 表明,与生产中常用的焊前打磨处理相比,尽管对接面未机械打磨的接头焊核区的"S"线更明显,但是两种接头的硬度分布和拉伸性能相当,拉伸时都在最低硬度区即热影响区断裂.高周疲劳实验结果表...     

Effects of microstructural through‐thickness non‐uniformity and crack size on fatigue crack propagation and fracture of rolled Al‐7075 alloy

Some of the fatigue tests performed using the standard compact tension (CT) and a non‐standard specimen made of rolled 7075 aluminium alloy exhibit fatigue crack growth (FCG) lagging in a small region along the crack front. Through‐thickness microstructural evaluation shows that material grains in this region did not flatten as much as other regions. In the non‐standard specimen, surface cracks are either grown under fatigue loading or broken under monotonically increasing quasi‐static loads at different crack sizes. The aforementioned lagging also exists in a narrow region of 3‐D FCG for specimens with microstructural through‐thickness non‐uniformity. A more important feature for this type of specimen with surface crack is the deflection of fast fracture direction into the grain interfaces, namely from L‐T orientation to S‐L and S‐T directions. It is proved that this is due to significant levels of second principal stresses near the free surface for small cracks and lower fracture toughness of the material in S‐L and S‐T directions.     

Crack path and fracture analysis in FSW of small diameter 6082-T6 aluminium tubes under tension–torsion loading

This paper reports part of the work done in a research project aimed at developing an optimised process to join 38 mm diameter tubes of 6082-T6 aluminium alloy using friction stir welding (FSW), and then to determine the fatigue performance under tension, torsion and tension–torsion loading conditions. The final outcome of the project is intended to be guidance for fatigue design of small diameter aluminium tubes joined by FSW, and this paper presents information on crack path and defects under the various loading conditions. Crack path analysis was performed using both low magnification stereo microscopy and scanning electron microscopy, in order to identify crack initiation sites, the direction of crack propagation and the interrelated influence of microstructure and weld geometry on the crack initiation path.     

Identification of the pin offset effect on the friction stir welding (FSW) via Taguchi – Grey relational analysis: A Case study for AA 7075 – AA 6013 alloys

The aim of this work is to present a case study relating to the dissimilar friction stir welding (FSW) ability of AA 7075‐T651 and AA 6013‐T6 by applying pin offset technique. An orthogonal array L18 was conducted to perform the overlapped weld seams using three different values of pin offset, welding speed and tool rotational speed along with two different pin profiles determine the impact of welding parameters on the tensile properties of friction stir welded joints. The nugget zone for each of overlapped weld seams exhibited a complex structure and also, the pin offset and profile also were found to have a great impact on the microstructural evolution of the nugget zone. The ultimate tensile strength, elongation at the rapture and bending strength of welded joints were measured in the ranges of 194–215 MPa, 1.79–3.34 % and 203–352 MPa. From the Taguchi based Grey relational analysis, the optimum welding condition was determined for the welded joint performed using a single fluted pin profile with the zero pin offset, tool rotational speed of 630 min^?1 and welding speed of 63 mm/min. Microstructural and macro‐structural observations revealed that welded joints exhibiting lower tensile strength are consistent of various types of defects (e. g. cracks, tunnels and cavities). The fracture location of welded joints was found to be on the heat affected zone and between the heat affected zone and AA 6013‐base metal. The tool and pin wear was not observed during the welding applications     

Fatigue crack growth resistance of gas tungsten arc,electron beam and friction stir welded joints of AA2219 aluminium alloy

AA2219 aluminium alloy square butt joints without filler metal addition were fabricated using gas tungsten arc welding (GTAW), electron beam welding (EBW) and friction stir welding (FSW) processes. The effect of three welding processes on fatigue crack growth behaviour is reported in this paper. Transverse tensile properties of the welded joints were evaluated. Microstructure analysis was also carried out using optical and electron microscopes. It was found that the FSW joints are exhibiting superior fatigue crack growth resistance compared to EBW and GTAW joints. This was mainly due to the formation of very fine, dynamically recrystallised grains and uniform distribution of fine precipitates in the weld region.     

Limited weld residual stress measurements in fatigue crack propagation: Part II. FEM-based fatigue crack propagation with complete residual stress fields

Using a limited set of residual stress measurements acquired by neutron diffraction and an equilibrium‐based, weighted least square algorithm to reconstruct the complete residual stress tensor field from the measured residual stress data, the effect of weld residual stress on fatigue crack propagation is investigated for 2024‐T351 aluminium alloy plate joined by friction stir welding. Through incorporation of the least squares, complete equilibrated residual stress field into a finite element model of the Friction Stir Weld (FSW) region, progressive crack growth along a direction perpendicular to the welding line is simulated as part of the analysis. Both the residual stress redistribution and the stress intensity factor due to the residual stress field, K_res, are calculated during the crack extension process. Results show that (a) incorporation of the complete, self‐equilibrated residual stress field into a finite element (FE) model of the specimen provides a robust, hybrid approach for assessing the importance of residual stress on fatigue crack propagation, (b) the calculated stress‐intensity factor due to the residual stress field, K_res, has the same trend as measured experimentally by the ‘cut‐compliance method’ and (c) the da/dN results are readily explained with reference to the effect of the residual stress field on the applied stress intensity factor.     

Evaluation of the two‐parameter fracture criterion for various crack configurations made of 7075‐T6 aluminium alloy using finite‐element fracture simulations

For many years, a two‐parameter fracture criterion (TPFC) has been used to correlate and predict failure loads on cracked metallic fracture specimens. The current study was conducted to evaluate the use of the TPFC on a high‐strength aluminium alloy, using elastic‐plastic finite‐element (FE) analyses with the critical crack‐tip‐opening angle (CTOA) fracture criterion. In 1966, Forman generated fracture data on middle‐crack tension, M(T), specimens made of thin‐sheet 7075‐T6 aluminium alloy, which is a quasi‐brittle material. The fracture data included a wide range of specimen half‐widths (w) ranging from 38 to 305 mm. A two‐dimensional FE analysis code (ZIP2D) with a “plane‐strain core” option was used to model the fracture process with a critical CTOA chosen to fit the M(T) test data. Fracture simulations were then conducted on other M(T), single‐edge‐crack tension, SE(T), and bend, SE(B), specimens over a wide range in widths (w = 19‐610 mm). No test data were available on the SE‐type specimens. The results supported the TPFC equation for net‐section stresses less than the material proportional limit. However, some discrepancies in the FE fracture simulations results were observed among the numerical analyses made on the three specimen types. Thus, more research is needed to improve the transferability of the TPFC from the M(T) specimen to both the SE(T) and SE(B) specimens for quasi‐brittle materials.     

Effects of ultrasonic assisted friction stir welding on flow behavior,microstructure and mechanical properties of 7N01-T4 aluminum alloy joints

Conventional friction stir welding(FSW) and ultrasonic assisted friction stir welding(UAFSW) were employed to weld 6-mm thick 7 N01-T4 aluminum alloy plates. Weld forming characteristics and material flow behavior in these two different welding processes were studied and compared. Ultrasonic vibration was applied directly on the weld in axial direction through the welding tool. Metal flow behavior,microstructure characteristics in the nugget zone(NZ) and evolution of the mechanical properties of naturally aged joints were studied. Results show that the ultrasonic vibration can significantly increase the welding speed of defect-free welded joint. At the rotation speed of 1200 rpm, the UAFSW can produce defect-free welded joints at a welding speed that is 50% higher than that of the conventional FSW.Ultrasonic vibrations can also improve surface quality of the joints and reduce axial force by 9%. Moreover, ultrasonic vibrations significantly increase the volume of the pin-driven zone(PDZ) and decrease the thickness of the transition zone(TZ). The number of subgrains and deformed grains resulting from the UAFSW is higher than that from the FSW. By increase the strain level and strain gradient in the NZ,the ultrasonic vibrations can refine the grains. Ultrasonic energy is the most at the top of the NZ, and gradually reduces along the thickness of the plate. The difference in strengths between the FSW and the UAFSW joints after post-weld natural aging(PWNA) is small. However, the elongation of the UAFSW is8.8% higher than that of the FSW(PWNA for 4320 h). Fracture surface observation demonstrates that all the specimens fail by ductile fracture, and the fracture position of the UAFSW joint changes from HAZ(PWNA for 120 h) to NZ(PWNA for 720 and 4320 h).     

An experimental and theoretical study of crack propagation in crossply fiber composites

Rectangular specimens of a cross-ply fiberglass composit e (Scotchply 1002) in which sharp edge notches have been cut along one of the fiber directions parallel to a specimen edge have been tested in an “Instron” testing machine. Tensile stress was applied perpendicular to the direction of the notch. The commencement and growth of the crack has been observed. It has been found that if the notch is sufficiently close to one edge of the specimen the crack instead of propagating along the direction of its axis, i.e. perpendicular to the applied stress runs along the stress direction; when the notch is sufficiently far from the edge the crack propagates in the direction of its axis right across the specimen while at intermediate notch positions the crack runs along in its axial direction and then turns sharply through a right angle and continues in the direction of the applied stress. The theory of this behavior has been studied and it is shown that if a criterion of a critical tensile force rather than a critical energy density is used, the observed phenomena can, at least qualitatively, be accounted for. The comparable situation for a brittle isotropic specimen of “Plexiglass” is also described. This shows a quite different response and conventional linear fracture mechanics can be used to describe this behavior.     

Establishing relationships between mechanical properties of aluminium alloys and optimised friction stir welding process parameters

Friction stir welding (FSW) is a solid state welding process for joining aluminium alloys and is employed in aerospace, rail, automotive and marine industries. In FSW, the base metal properties such as yield strength, hardness and ductility control the plastic flow of the material under the action of a rotating non-consumable tool. The FSW process parameters such as, the tool rotational speed, the welding speed and the axial force play a major role in deciding the weld quality. In this investigation, FSW joints were made using six different grades of aluminium alloys (AA1100, AA2219, AA2024, AA6061, AA7039, and AA7075) using different levels of process parameters. Macrostructural analysis was carried out to identify the feasible working range of process parameters. The optimal welding conditions to attain maximum strength for each alloy were identified using Response Surface Methodology (RSM). Empirical relationships were established between the base metal mechanical properties of aluminium alloys and optimised FSW process parameters. These relationships can be effectively used to predict the optimised FSW process parameters from the known base metal properties (yield strength, elongation and hardness).     

Predicting tensile strength,hardness and corrosion rate of friction stir welded AA6061-T6 aluminium alloy joints

AA6061-T₆ aluminium alloy (Al–Mg–Si alloy) has gathered wide acceptance in the fabrication of light weight structures requiring high strength-to-weight ratio and good corrosion resistance. The friction stir welding (FSW) process and tool parameters play major role in deciding the joint characteristics. In this research, the tensile strength and hardness along with the corrosion rate of friction-stir-butt welded joints of AA6061-T₆ aluminium alloy were investigated. The relationships between the FSW parameters (rotational speed, welding speed, axial force, shoulder diameter, pin diameter and tool hardness) and the responses (tensile strength, hardness and corrosion rate) were established. The optimal welding conditions to maximize the tensile strength and minimize the corrosion rate were identified and reported here.     

Influence of a non-rotating shoulder on heat generation,microstructure and mechanical properties of dissimilar AA2024/AA7050 FSW joints

Friction stir welding (FSW) and stationary shoulder friction stir welding (SSFSW) were carried out for the butt joining of dissimilar AA2024-T3 and AA7050-T7651 aluminium alloys with thicknesses of 2 mm. A comparison between the two processes was performed by varying the welding speed while keeping the rotational speed constant. Through the analysis of the force and torque produced during welding and a simple analytical model, it was possible to show that in SSFSW there is more effective coupling with the tool and the heat produced is more efficiently distributed. This process decreases both the welding area and the diffusion at the interface of the two alloys compared with FSW. The minimum microhardness occurred at the advancing side (AS) at the interface between the thermo-mechanically affected zone (TMAZ) and the stir zone (SZ) in both processes, although the decrease was more gradual in SSFSW. This interface is also where all specimens failed for both welding technologies. An increase in tensile strength was measured in SSFSW compared with standard FSW. Furthermore, it was possible to establish the mechanical performance of the material in the fracture zone using digital image correlation.     

Relationship between base metal properties and friction stir welding process parameters

Friction stir welding (FSW) is a solid state welding process for joining aluminum alloys and has been employed in aerospace, rail, automotive and marine industries for joining aluminium, magnesium, zinc and copper alloys. In FSW, the base metal properties such as yield strength, ductility and hardness control the plastic flow of the material under the action of rotating non-consumable tool. The FSW process parameters such as tool rotational speed, welding speed, axial force, etc. play a major role in deciding the weld quality. In this investigation, an attempt has been made to establish relationship between the base material properties and FSW process parameters. FSW joints have been made using five different grades of aluminium alloys (AA1050, AA6061, AA2024, AA7039 and AA7075) using different combinations of process parameters. Macrostructural analysis has been done to check the weld quality (defective or defect free). Empirical relationships have been established between base metal properties and tool rotational speed and welding speed, respectively. The developed empirical relationships can be effectively used to predict the FSW process parameters to fabricate defect free welds.     

氧化膜对6082铝合金搅拌摩擦焊接头疲劳性能的影响

对6 mm厚的6082-T6铝合金进行两种表面处理然后实施搅拌摩擦焊接,研究了对接面氧化膜对接头组织和疲劳性能的影响。结果表明,进行速度为1000 mm/min的高速焊接时,对接面未打磨和打磨的接头焊接质量都良好,接头强度系数达到81%;两种接头的疲劳性能基本相同,疲劳强度均为100 MPa;少数样品在焊核区外断裂,大部分样品在热影响区断裂。与接头相比,两种接头焊核区的疲劳性能有所提高,均为110 MPa,在疲劳测试中裂纹并未沿“S”线萌生和扩展。     

拉伸载荷下碳纤维复合材料T型接头脱粘特性与FBG监测分析

研究了拉伸载荷下碳纤维复合材料(CFRP)T型接头的界面脱粘与裂纹扩展过程。对拉伸载荷下T型接头破坏过程进行数值模拟;在模拟敏感区域布置光纤布拉格光栅(FBG),实时监测界面脱粘的产生及扩展应变特征;使用高速摄像机,捕捉脱粘及裂纹扩展的图像数据。结果表明:T型接头的三角填料区首先出现损伤,裂纹向两个方向扩展。水平方向:向L型层与一型层之间的胶层扩展;竖直方向:向两个L型层之间的胶层扩展。裂纹扩展最终引起结构失效。光纤布拉格光栅中心波长的变化能够在非视觉条件下记录损伤的出现、积累与扩展,可正确预警结构内部损伤的产生,还原裂纹扩展路径。     

Microstructural evolution of aluminum alloy during friction stir welding under different tool rotation rates and cooling conditions

The microstructural evolution during friction stir welding (FSW) has long been studied only using one single welding parameter. Conclusions were usually made based on the final microstructure observation and hence were one-sided. In this study, we used the “take-action” technique to freeze the microstructure of an Al-Mg-Si alloy during FSW, and then systematically investigated the microstructures along the material flow path under different tool rotation rates and cooling conditions. A universal characteristic of the microstructural evolution including four stages was identified, i.e. dynamic recovery (DRV), dislocation multiplication, new grain formation and grain growth. However, the dynamic recrystallization (DRX) mechanisms in FSW depended on the welding condition. For the air cooling condition, the DRX mechanisms were related to continuous DRX associated with subgrain rotation and geometric DRX at high and low rotation rates, respectively. Under the water cooling condition, we found a new DRX mechanism associated with the progressive lattice rotation resulting from the pinning of the second-phase particles. Based on the analyses of the influencing factors of grain refinement, it was clearly demonstrated that the delay of DRV and DRX was the efficient method to refine the grains during FSW. Besides, ultra-high strain rate and a short duration at high temperatures were the key factors to produce an ultrafine-grained material.     

Effect of friction stir welding on microstructure,tensile and fatigue properties of the AA7005/10 vol.%Al2O3p composite

Several studies have been recently focused on friction stir welding of aluminium alloys and some data are also reported on FSW of aluminium-based composites. The application of this solid state welding technique to particles reinforced composites seems very attractive, since it should eliminate some typical defects induced by the traditional fusion welding techniques, such as: gas occlusion, undesidered interfacial chemical reactions between the reinforcement and the molten matrix alloy, inhomogeneous reinforcement distribution after welding. The present work describes the effect of the FSW process on the microstructure and, consequently, on the tensile and low-cycle fatigue behaviour, of an aluminium matrix (AA7005) composite reinforced with 10 vol.% of Al₂O₃ particles (W7A10A). The microstructural characterization evidenced, in the FSW zone, a substantial grain refinement of the aluminium alloy matrix (due to dynamic recrystallization induced by the plastic deformation and frictional heating during welding) and a significant reduction of the particles size (due to the abrasive action of the tool). Tensile tests showed a high efficiency of the FSW joints (about 80% of the ultimate tensile strength). The low-cycle fatigue tests evidenced a fatigue life reduction for the FSW material respect to the base composite, particularly for high values of total strain range. The fracture mechanisms for the FSW specimens were those typical of metal matrix composites: interfacial decohesion, void nucleation and growth, as well as fracture of reinforcing particles, as shown by SEM analyses of the fracture surfaces.     

Transverse fatigue behaviour and residual stress analyses of double sided FSW aluminium alloy joints

Friction stir welding (FSW) since its invention has been attracting relevant interest for joining aluminium alloys. Due to the nature of this process, the materials can be joint without melting. Thanks to this peculiar characteristic, the issues associated with the cooling from liquid phase are avoided or considerably reduced, such as cracking, porosity, and defects. However, as well as other well‐established welding techniques, the FSW process gives rise to formation of residual stress in the welding region and surrounding volume: heat and thermo‐mechanical affected zones. Presence of residual stress in a mechanical component is well‐known to affect its performance, particularly regarding fatigue at high number of cycles. Another aspect that influences the fatigue life is the underlying microstructure. In this work, we firstly study the residual stress field and the underlying microstructural features arising in FSW butt joints and their effect on the fatigue performance of this type of weldments. The evaluation of residual stress field is carried out by means of modern experimental techniques. In the first instance, synchrotron X‐ray powder diffraction was employed for two‐dimensional full field maps of residual stress. Corroboration of these measurements was done by exploiting the capability of focused ion beam and digital image correlation (FIB‐DIC), which is able to deliver pointwise absolute measurement of residual stress. A set of FSW samples were then tested under uniaxial fatigue loading at several loading ranges, in the high cycle fatigue regime, in order to understand whether the severity of loads affects the crack path and life endurance. Fractographic and electron backscattered diffraction (EBSD) analysis then revealed crack nucleation site and propagation mechanisms with the respect of the underlying microstructure. Outcome of these experimental studies is then thoroughly discussed.     

Establishing relationship between the base metal properties and friction stir welding process parameters of cast aluminium alloys

In friction stir welding (FSW), the material under the rotating action of non-consumable tool has to be stirred properly to get defect free welds in turn it will improve the strength of the welded joints. The welding conditions and parameters are differing based on the mechanical properties of base materials such as tensile strength, ductility and hardness which control the plastic deformation during friction stir welding. The FSW process parameters such as tool rotation speed, welding speed and axial force, etc. play a major role in deciding the weld quality. FSW Joints of cast aluminium alloys A319, A356, and A413 were made by varying the FSW process parameters and the optimum values were obtained. In this investigation, empirical relationships are established and they can be effectively used to predict the optimum FSW process parameters to fabricate defect free joints with high tensile strength from the known base metal properties of cast aluminium alloys.     

The effect of weld parameters on friction stir welding of brass plates

More successful results have been obtained in butt‐ and overlap‐joining of Al‐alloy plates by a recently developed solid state joining technique, namely friction stir welding (FSW), than in more conventional fusion welding processes. In this joining technique, no fusion takes place in the joint area of the plates welded. This novel joining method also offers the potential to weld some other materials rather than Al‐alloys, such as Mg‐alloys, brasses and low strength steels. In this study, the applicability of friction stir welding to brasses, namely 90 %Cu‐10 %Zn and 70 %Cu‐30 %Zn alloys, has been investigated. The joint performance was determined by conducting optical microscopy, microhardness mesurements and mechanical testing (e.g. tensile and bend tests). The effect of welding speed on the joint quality at a given rotational speed of the stirring pin (i.e. 1600 rpm) was also determined for both alloys. The highest joint performances were obtained at a welding speed of 210 mm/min for both alloys.