Supply Switching With Ground Collapse: Simultaneous Control of Subthreshold and Gate Leakage Current in Nanometer-Scale CMOS Circuits

Power gating has been widely used to reduce subthreshold leakage. However, the efficiency of power gating degrades very fast with technology scaling, which we demonstrate by experiment. This is due to the gate leakage of circuits specific to power gating, such as storage elements and output interface circuits with a data-retention capability. A new scheme called supply switching with ground collapse is proposed to control both gate and subthreshold leakage in nanometer-scale CMOS circuits. Compared to power gating, the leakage is cut by a factor of 6.3 with 65-nm and 8.6 with 45-nm technology. Various issues in implementing the proposed scheme using standard-cell elements are addressed, from register transfer level to layout. These include the choice of standby supply voltage with circuits that support it, a power network architecture for designs based on standard-cell elements, a current switch design methodology, several circuit elements specific to the proposed scheme, and the design flow that encompasses all the components. The proposed design flow is demonstrated on a commercial design with 90-nm technology, and the leakage saving by a factor of 32 is observed with 3% and 6% of increase in area and wirelength, respectively.     

The Circuits and Robust Design Methodology of the Massively Parallel Processor Based on the Matrix Architecture

Novel circuits and design methodology of the massively parallel processor based on the matrix architecture are introduced. A fine-grained processing elements (PE) circuit for high-throughput MAC operations based on the Booth's algorithm enhances the performance of a 16-bit fixed-point signed MAC, which operates up to 30.0GOPS/W. The dedicated I/O interface circuits are designed for converting the direction of data access and supporting the interleaved memory architecture, and they are implemented for maximizing the processor core efficiency. Power management techniques for suppressing current peaks and reducing average power consumption are proposed to enhance the robustness of the macro. The circuits and the design methodology proposal in this paper are attractive for achieving a high performance and robust massively parallel SIMD processor core employed in multimedia SoCs     

A new family of zero-voltage-transition PWM converters with dual active auxiliary circuits

A new family of active auxiliary circuits that allow the power switch in single switch, pulsewidth modulated converters to operate with zero-voltage switching is proposed in this paper. The main feature of an auxiliary circuit belonging to this family is that the auxiliary switch can operate with a zero-current switching turn-on and turn-off without increasing the peak current stresses of the main switch. This is an improvement over previous proposed auxiliary circuits where either the auxiliary switch operates with a hard turn-off or the circuit itself increases the peak stresses of the main switch. In this paper, the fundamental principles behind the proposed family of active auxiliary circuits are explained. Based on these principles, an example auxiliary circuit is systematically derived and presented along with several other auxiliary circuits belonging to the new family. The operation of a boost converter operating with the example auxiliary circuit is discussed in detail, and general guidelines for the design and implementation of auxiliary circuits belonging to the new family are given. The feasibility of the example auxiliary circuit is confirmed by experimental results obtained from a 500-W, 100-kHz boost converter laboratory prototype.     

Pass transistor with dual threshold voltage domino logic design using standby switch for reduced subthreshold leakage current

Dual threshold voltages domino design methodology utilizes low threshold voltages for all transistors that can switch during the evaluate mode and utilizes high threshold voltages for all transistors that can switch during the precharge modes. We employed standby switch can strongly turn off all of the high threshold voltage transistors which enhances the effectiveness of a dual threshold voltage CMOS technology to reduce the subthreshold leakage current. Subthreshold leakage currents are especially important in burst mode type integrated circuits where the majority of the time for system is in an idle mode. The standby switch allowed a domino system enters and leaves a low leakage standby mode within a single clock cycle. In addition, we combined domino dynamic circuits style with pass transistor XNOR and CMOS NAND gates to realize logic 1 output during its precharge phase, but not affects circuits operation in its evaluation and standby phase. The first stage NAND gates output logic 1 can guarantee the second stage computation its correct logic function when system is in a cascaded operation mode. The processing required for dual threshold voltage circuit configuration is to provide an extra threshold voltage involves only an additional implant processing step, but performs lower dynamic power consumption, lower delay and high fan-out, high switching frequencies circuits characteristics. SPICE simulation for our proposed circuits were made using a 0.18 µm CMOS process from TSMC, with 10 fF capacitive loads in all output nodes, using the parameters for typical process corner at 25 °C, the simulation results demonstrated that our designed 8-bit carry look-ahead adders reduced chip area, power consumption and propagation delay time more than 40%, 45% and around 20%, respectively. Wafer based our design were fabricated and measured, the measured data were listed and compared with simulation data and prior works. SPICE simulation also manifested lower sensitivity of our design to power supply, temperature, capacitive load and process variations than the dynamic CMOS technologies.     

A practical high-latchup immunity design methodology for internalcircuits in the standard cell-based CMOS/BiCMOS LSIs

A practical high-latchup-immunity design methodology is proposed for high-density internal circuits in standard cell-based CMOS/BiCMOS LSIs. Both locally injected trigger current and uniformly generated trigger current were measured using a new test structure. Focusing on the difference in the well shunt resistance between local and uniform trigger currents, a practical latchup-free guideline based on an analytical model for uniformly generated trigger current in the well is presented for the periodic placement of well contacts dependent on parasitic device parameters, on generated trigger current level, and a layout pattern size     

Theory of differential current switches and logic design of ternary ECL circuits at switch level

Starting from the viewpoint that the switch states and signal values in a digital circuit should be described separately by two different kinds of variable, the interaction between the switching element and signal in multi-valued ECL circuits is analysed and two types of connection operations, threshold switching operation and current switching operation, are proposed. The properties and circuit realizations of these new operations are discussed and the theory of differential current switches applicable to ECL circuits is established. Examples of basic ternary ECL circuits confirm that this theory can effectively guide the logic design of ternary ECL circuits at switch level. The circuits are verified by using the SPICE II program. They have the same logic level difference and transient characteristic as binary ECL circuits. Since the multi-valued ECL circuit uses only one set of power supply and can set several threshold values by using reference levels, it can be fabricated using conventional ECL techniques and is compatible with binary ECL circuits.     

900 MHz CDMA/1.8 GHz PCS/450 MHz CDMA RF receiver ICs with a new mixer linearization method and optimization of integrated inductor for single balance mixer LO buffer

900 MHz CDMA, 1.8 GHz PCS, and 450 MHz CDMA RF receivers are implemented and measured. In order to reduce NRE cost and meet the demand of fast time-to-market, a metal-mask configurable method is applied for those receivers using only upper metals, contact and via layers. Also to reduce power consumption, a new mixer linearization method is proposed, along with an optimization methodology of an integrated inductor for a single balance mixer LO buffer, with respect to power consumption and silicon area. In order to apply the proposed inductor optimization methodology into metal-mask configurable circuits, inductor design considerations for metal-mask variant circuits are presented. With the proposed linearization technique and inductor optimization method, low power 900 MHz CDMA/1.8 GHz PCS/450 MHz CDMA mixers are obtained. The proposed receivers are fabricated in a 0.35 μm SiGe BiCMOS process. In the 900 MHz CDMA case, measurement results of the proposed mixer show 12 dBm IIP3 and 10.2 dB conversion gain, and 7.5 dB SSB NF with 10.5 mA current consumption at 2.7 V supply voltage.     

Adaptive power gating of 32-bit Kogge Stone adder

Static power consumes a significant portion of the available power budget. Consequently, leakage current reduction techniques such as power gating have become necessary. Standard global power gating approaches are an effective method to reduce idle leakage current, however, global power gating does not consider partially idle circuits and imposes significant delay and routing constraints. An adaptive power gating technique is applied locally to a 32-bit Kogge Stone adder, and evaluated at the 16 nm FinFET technology node. This high granularity adaptive power gating approach employs a local controller to lower energy use and reduce circuit overhead. The controller conserves additional power when the circuit is partially idle (based on the inputs to the adder) by adaptively powering down inactive blocks. Moreover, the local controller reduces routing complexity since a global power gating signal is not required. The proposed adaptive power gating technique exhibits significant energy savings, ranging from 8% to 21%. This technique targets partially idle circuits, and therefore complements rather than replaces global power gating techniques. A 12% delay overhead results in a 5% area overhead. This delay overhead is reduced to 5% by increasing the area overhead to 16%, and can be further reduced by trading off additional area.     

Using SAT-based techniques in power estimation

Recent algorithmic advances in Boolean satisfiability (SAT), along with highly efficient solver implementations, have enabled the successful deployment of SAT technology in a wide range of applications domains, and particularly in electronic design automation (EDA). SAT is increasingly being used as the underlying model for a number of applications in EDA. This paper describes how to formulate two problems in power estimation of CMOS combinational circuits as SAT problems or 0–1 integer linear programming (ILP). In these circuits, it was proven that maximizing dissipation is equivalent to maximizing gate output activity, appropriately weighted to account for differing load capacitances. The first problem in this work deals with identifying an input vector pair that maximizes the weighted circuit activity. In the second application we attempt to find an estimate for the maximum power-up current in circuits where power cut-off or gating techniques are used to reduce leakage current. Both problems were successfully formulated as SAT problems. SAT-Based and generic Integer Linear Programming (ILP) solvers are then used to find a solution. The experimental results obtained on a large number of benchmark circuits provide promising evidence that the proposed complete approach is both viable and useful and outperforms the random approach.     

Clock Skew Optimization for Peak Current Reduction

The presence of large current peaks on the power and ground lines is a serious concern for designers of synchronous digital circuits. Current peaks are caused by the simultaneous switching of highly loaded clock lines and by the signal propagation through the sequential logic elements. In this work we propose a methodology for reducing the amplitude of the current peaks. This result is obtained by clock skew optimization. We propose an algorithm that, for a given clock cycle time, determines the clock arrival time at each flip-flop in order to minimize the current peaks while respecting timing constraint. Our results on benchmark circuits show that current peaks can be reduced without penalty on cycle time and average power dissipation. Our methodology is therefore well-suited for low-power systems with reduced supply voltage, where low noise margins are a primary concern.     

A reliable ground bounce noise reduction technique for nanoscale CMOS circuits

Power gating is the most effective method to reduce the standby leakage power by adding header/footer high-V_TH sleep transistors between actual and virtual power/ground rails. When a power gating circuit transitions from sleep mode to active mode, a large instantaneous charge current flows through the sleep transistors. Ground bounce noise (GBN) is the high voltage fluctuation on real ground rail during sleep mode to active mode transitions of power gating circuits. GBN disturbs the logic states of internal nodes of circuits. A novel and reliable power gating structure is proposed in this article to reduce the problem of GBN. The proposed structure contains low-V_TH transistors in place of high-V_TH footer. The proposed power gating structure not only reduces the GBN but also improves other performance metrics. A large mitigation of leakage power in both modes eliminates the need of high-V_TH transistors. A comprehensive and comparative evaluation of proposed technique is presented in this article for a chain of 5-CMOS inverters. The simulation results are compared to other well-known GBN reduction circuit techniques at 22 nm predictive technology model (PTM) bulk CMOS model using HSPICE tool. Robustness against process, voltage and temperature (PVT) variations is estimated through Monte-Carlo simulations.     

A zero-voltage transition boost converter using a zero-voltage switching auxiliary circuit

A soft switching boost converter with zero-voltage transition (ZVT) main switch using zero-voltage switching (ZVS) auxiliary switches is proposed. Various operating intervals of the converter are presented and analyzed. Design considerations are discussed. A design example with experimental results obtained from a 300-W, 250-kHz, 300-V output DC-DC converter is presented. A modified gating scheme to utilize the auxiliary switch in the main power processing is discussed. A 600-W, 100-kHz, 380 V output, 90-250 V AC, power factor corrected, AC-to-DC, boost converter with the modified gating scheme is presented. Results show that the main switch maintains ZVT while auxiliary switches retain ZVS for the complete specified line and load conditions. Parasitic oscillations existing in the converters proposed in the literature are completely removed.     

Efficient algorithms for multilevel power estimation of VLSI circuits

This paper presents a methodology for calculating highly accurate mean power estimates for integrated digital CMOS circuits. A complementary calibration scheme for ASIC library cells to extract the power relevant parameters is proposed. The circuit models presented allows the prediction of mean power dissipation of gate-level designs in CMOS technologies with an accuracy that is comparable to a SPICE simulation but up to 10 000 times faster. The outlined approach is capable of handling complex circuits consisting of more than 20 000 cells and thousands of memory elements. Very large sets of input data with several millions of patterns can, thus, be simulated in an efficient way. This allows the prediction of mean power dissipation of VLSI circuits in a realistic functional context which provides new assessment possibilities for digital CMOS low-power design methods. Experimental results for some benchmark circuits are detailed in order to demonstrate the significant improvements in terms of performance, accuracy, and flexibility of this approach compared to state-of-the-art power estimation methods     

PWM buck-boost ac choppers for safe commutation

Novel pulse-width modulated (PWM) buck-boost ac choppers solving the commutation problem are proposed for single-phase and three-phase systems. The power circuits of the single-phase and three-phase buck-boost ac choppers use only two and three standard switch modules, respectively, and regenerative dc snubbers are attached directly to standard switch modules to absorb energy stored in line stray inductance. The switching policy for solving the commutation problem is achieved. Compared with previous buck-boost ac choppers, the switching loss is reduced and RC snubbers causing power loss are eliminated. The equivalent circuits of the proposed ac choppers are obtained and the power factor is derived from the equivalent circuits. The proposed ac chopper has the following advantages; improved power factor, low harmonics, sinusoidal input current, fast dynamics, high efficiency, high reliability, and significant reduction of the filter size. Experimental results show that the proposed scheme gives good steady-state performances of the ac chopper and that they coincide with the theoretical results.     

Wakeup scheduling and its buffered tree synthesis for power gating circuits

Power gating circuit suffers from large amount of rush current during wakeup, especially when all switch cells are turned on simultaneously. If each switch cell is turned on at a different time, rush current can be reduced. It is shown in this paper that rush current can be reduced even more if signal transition time (or signal slew) to each switch cell is adjusted. We define wakeup scheduling as to determine turn-on time and signal slew of each switch cell; the goal is to minimize wakeup delay while keeping rush current below the maximum value that is allowed. The determined turn-on time and signal slew are implemented using a buffered tree. The wakeup scheduling and buffered tree construction are integrated into a design flow. To adapt to process variation, we use adjustable delay buffers in the wakeup network. We also apply grid-based design flow and use Schmitt triggers to implement large designs. Experiments in an industrial 1.1 V, 32-nm technology demonstrate that the wakeup delay is reduced by 12% on average of example circuits compared with turn-on scheduling.     

开关——信号理论与数字电路的开关级设计

本文在分析数字电路的传统设计理论中存在问题的基础上，提出了使用开关变量与信号变量来分别描写数字电路内部元件的开关状态与电路信号等二者，并由此出发建立了开关——信号理论。根据具体数字电路内部的工作原理，本文分别对CMOS与ECL等二种电路进行了讨论．并发展了相应的开关级设计技术。设计实例表明，由于设计中以开关晶体管为构造单元，因此开关级设计的电路要比传统的仃级设计具有较简单的结构。     

Power complexity of multiplexer-based optoelectronic crossbar switches

The integration of thousands of optical input/output (I/O) devices and large electronic crossbar switching elements onto a single optoelectronic integrated circuit (IC) can place stringent power demands on the CMOS substrates. Currently, there is no sufficiently general analytic methodology for power analysis and power reduction of large-scale crossbar switching systems. An analysis of the power complexity of single-chip optoelectronic switches is presented, assuming the classic broadcast-and-select crossbar architecture. The analysis yields the distribution of power dissipation and allows for design optimization. Both unpipelined and pipelined designs are analyzed, and a technique to reduce power dissipation significantly is proposed. The design of a 5.12 Tbit single-chip optoelectronic switch using 0.18-/spl mu/m CMOS technology is illustrated. The pipelined switch design occupies < 70 mm/sup 2/ of CMOS area, and consumes <80 W of power, which compares favorably to the power required in electrical crossbar switches of equivalent capacity.     

基于ADE7878的多路电量检测系统设计

为了解决工控领域多路交流电参数检测,需要独立进行单路测量电路设计的问题,给出了一种基于ADE7878芯片和嵌入式技术设计的多路电参数采集系统的硬件电路和程序流程。系统采用LPC2132作为主控芯片,适时控制4052多路开关,切换各路信号,通过I2C通信接口,读取ADE7878电能芯片采集的电量参数,同时通过RS485通信接口,上传电参数。实验结果表明,该采集系统最多可采集4路三相电的电压,电流,功率,功率因数,电能均能实现1%的计量精度,具有应用灵活,外围电路简单,可靠性高,成本低的特点。本电路设计亦可为相关产品的测试系统研发提供参考。     

Activity correlation-based clustering clock-gating technique for digital filters

Clock gating is an effective way to reduce the dynamic power in digital sequential circuits. In this paper, a gate-level activity correlation-based clustering clock-gating (CCG) technique is proposed for digital filters. The CCG technique exploits the correlations between flip-flops, and determines how to group the flip-flops for clock gating. An Activity Correlation Matrix (ACMtx) is introduced to describe the correlations between the flip-flops, and a greedy clustering algorithm is proposed to find an optimised clustering scheme as well. Experiments on ISCAS’89 benchmarks show that the proposed technique can reduce power consumption by 5.08% on average, on top of existing technique. For the circuits with large numbers of flip-flops, our proposed technique can save 15.84% more power on average.     

Design and Control for a Charge-Regulated Flyback Switch-Mode Rectifier

This paper presents the design and control of a single-stage charge-regulated varying-frequency flyback switch-mode rectifier (SMR). First, the ratings of key constituted circuit components are derived, and accordingly, the power circuit is designed and implemented. Then, a novel charge-regulated, varying-frequency, current-controlled pulsewidth modulation (CCPWM) switching scheme is developed. In the proposed control scheme, the switch turn-on time is fixed, and the turn-off time interval is determined by the comparison result between the low-pass filtered switch current and its current command. The proposed switching scheme possesses the features of without slope compensation, having more dispersedly distributed harmonic spectrum, robust current tracking control, and ease of implementation using off-the-shelf integrated circuits. Finally, the quantitative and robust voltage regulation controls considering nonlinear behavior are made. Good dc output voltage regulation and ac input power quality control performances under wide load range are obtained. Some simulated and measured results are provided to demonstrate the performance of the developed SMR.