Ga-doped ZnO transparent electrodes with TiO<Subscript>2</Subscript> blocking layer/nanoparticles for dye-sensitized solar cells

Ga-doped ZnO [GZO] thin films were employed for the transparent electrodes in dye-sensitized solar cells [DSSCs]. The electrical property of the deposited GZO films was as good as that of commercially used fluorine-doped tin oxide [FTO]. In order to protect the GZO and enhance the photovoltaic properties, a TiO₂ blocking layer was deposited on the GZO surface. Then, TiO₂ nanoparticles were coated on the blocking layer, and dye was attached for the fabrication of DSSCs. The fabricated DSSCs with the GZO/TiO₂ glasses showed an enhanced conversion efficiency of 4.02% compared to the devices with the normal GZO glasses (3.36%). Furthermore, they showed better characteristics even than those using the FTO glasses, which can be attributed to the reduced charge recombination and series resistance.     

Preparation of TiO<Subscript>2</Subscript> nanotube/nanoparticle composite particles and their applications in dye-sensitized solar cells

Efficiency of dye-sensitized solar cells [DSSCs] was enhanced by combining the use of TiO₂ nanotubes [TNTs] and nanoparticles. TNTs were fabricated by a sol-gel method, and TiO₂ powders were produced through an alkali hydrothermal transformation. DSSCs were constructed using TNTs and TiO₂ nanoparticles at various weight percentages. TNTs and TiO₂ nanoparticles were coated onto FTO glass by the screen printing method. The DSSCs were fabricated using ruthenium(II) (N-719) and electrolyte (I₃/I₃ ^-) dyes. The crystalline structure and morphology were characterized by X-ray diffraction and using a scanning electron microscope. The absorption spectra were measured using an UV-Vis spectrometer. The incident photocurrent conversion efficiency was measured using a solar simulator (100 mW/cm²). The DSSCs based on TNT/TiO₂ nanoparticle hybrids showed better photovoltaic performance than cells made purely of TiO₂ nanoparticles.     

Increases in solar conversion efficiencies of the ZrO<Subscript>2</Subscript> nanofiber-doped TiO<Subscript>2</Subscript> photoelectrode for dye-sensitized solar cells

In this paper, in order to improve the efficiency of dye-sensitized solar cells, we introduced zirconia [ZrO₂] nanofibers into a mesoporous titania [TiO₂] photoelectrode. The photoelectrode consists of a few weight percent of ZrO₂ nanofibers and a mesoporous TiO₂ powder. The mixed ZrO₂ nanofibers and the mesoporous TiO₂ powder possessed a larger surface area than the corresponding mesoporous TiO₂ powder. The optimum ratio of the ZrO₂ nanofiber was 5 wt.%. The 5 wt.% ZrO₂-mixed device could get a short-circuit photocurrent density of 15.9 mA/cm², an open-circuit photovoltage of 0.69 V, a fill factor of 0.60, and a light-to-electricity conversion efficiency of 6.5% under irradiation of AM 1.5 (100 mW/cm²).     

Energetic surface heterogeneity of nanocrystalline TiO<Subscript>2</Subscript> films for dye-sensitized solar cells

Dye sensitized solar cells (DSSCs) have been receiving significant attention because they have many advantages compared to conventional organic solar cells. It has been known that the photovoltaic characteristics of DSSC are highly dependent on the adsorption properties of dyes on TiO₂ films. To analyze the surface heterogeneity of TiO₂ surfaces, single-phase anatase nanocrystallite titanium films were prepared by sol-gel method using the hydrolysis reaction of titanium tetraisopropoxide under acidic condition and characterized by XRD, FE-SEM and BET analysis. The adsorption energy distribution functions were calculated by the generalized nonlinear regularization method. It was found that the shape and the intensity of the adsorption energy distribution curve determined were highly related with the physical properties (i.e., geometrical heterogeneity) and chemical characteristics (i.e., energetic heterogeneity) of nanocrystalline TiO₂ for DSSC.     

Mesoporous TiO<Subscript>2</Subscript> microspheres synthesized via a facile hydrothermal method for dye sensitized solar cell applications

Mesoporous TiO₂ microspheres were successfully synthesized by a facile hydrothermal process and the obtained product was sintered at 450 °C. The sintered TiO₂ powder was characterised by powder X-ray diffraction pattern and the result shows pure anatase phase with good crystalline nature. The morphological image of field emission scanning electron microscopy and high resolution transmission electron microscopy shows spherical shape and size of the particles is around 100 to 300 nm. The Brunauer–Emmett–Teller surface area of synthesized TiO₂ material was 56.32 m² g^?1 and average pore width of synthesized materials was 7.1 and 9.3 nm. Bimodal pore structure of TiO₂ microspheres has been very effective for electrolyte diffusion into photoanode in dye sensitized solar cells. The synthesized anatase TiO₂ microsphere based dye sensitized solar cells have high surface area with light scattering effect to enhance the photocurrent and conversion efficiency than the commercial P25 photoanode material. The power conversion efficiency of synthesized mesoporous TiO₂ microspheres and commercial P25 material is 4.2 and 2.7 % respectively. Therefore bimodal mesoporous anatase TiO₂ microsphere appears to be a promising and potential candidate for dye sensitized solar cells (DSSC) application.     

The effect of dye-sensitized solar cell based on the composite layer by anodic TiO2 nanotubes

TiO₂ nanotube arrays are very attractive for dye-sensitized solar cells (DSSCs) owing to their superior charge percolation and slower charge recombination. Highly ordered, vertically aligned TiO₂ nanotube arrays have been fabricated by a three-step anodization process. Although the use of a one-dimensional structure provides an enhanced photoelectrical performance, the smaller surface area reduces the adsorption of dye on the TiO₂ surface. To overcome this problem, we investigated the effect of DSSCs constructed with a multilayer photoelectrode made of TiO₂ nanoparticles and TiO₂ nanotube arrays. We fabricated the novel multilayer photoelectrode via a layer-by-layer assembly process and thoroughly investigated the effect of various structures on the sample efficiency. The DSSC with a four-layer photoelectrode exhibited a maximum conversion efficiency of 7.22% because of effective electron transport and enhanced adsorption of dye on the TiO₂ surface.     

Conversion enhancement of flexible dye-sensitized solar cells based on TiO2 nanotube arrays with TiO2 nanoparticles by electrophoretic deposition

We prepared highly ordered titanium dioxide nanotube arrays (TNAs) by anodizing Ti foils in F⁻ containing electrolyte. The thickness and dye loading amount of TNAs were 26 μm and 1.06 × 10⁻⁷ mol cm⁻², respectively. TiO₂ nanoparticles (TNPs) were electrophoretically deposited on the inner wall of nanotube to produce coated nanotube arrays (TNAP). The dye loading was increased to 1.56 × 10⁻⁷ mol cm⁻², and the electron transport rate improved. TNAs and TNAP were sensitized with ruthenium dye N3 to yield dye-sensitized TiO₂ nanotube solar cells. The power conversion efficiency of TNA-based dye-sensitized solar cells (DSSCs) was 4.28%, whereas the efficiency of TNAP-based DSSCs increased to 6.28% when illuminated from the counter electrode. The increase of power conversion efficiency of TNAP-based DSSCs is ascribed to the increased surface area of TNAs and the faster electron transport rate.     

Effect of TiO2 nanotubes with TiCl4 treatment on the photoelectrode of dye-sensitized solar cells

In this study, we used the electrochemical anodization to prepare TiO₂ nanotube arrays and applied them on the photoelectrode of dye-sensitized solar cells. In the field emission scanning electron microscopy analysis, the lengths of TiO₂ nanotube arrays prepared by electrochemical anodization can be obtained with approximately 10 to 30 μm. After titanium tetrachloride (TiCl₄) treatment, the walls of TiO₂ nanotubes were coated with TiO₂ nanoparticles. XRD patterns showed that the oxygen-annealed TiO₂ nanotubes have a better anatase phase. The conversion efficiency with different lengths of TiO₂ nanotube photoelectrodes is 3.21%, 4.35%, and 4.34% with 10, 20, and 30 μm, respectively. After TiCl₄ treatment, the efficiency of TiO₂ nanotube photoelectrode for dye-sensitized solar cell can be improved up to 6.58%. In the analysis of electrochemical impedance spectroscopy, the value of R_k (charge transfer resistance related to recombination of electrons) decreases from 26.1 to 17.4 Ω when TiO₂ nanotubes were treated with TiCl₄. These results indicate that TiO₂ nanotubes treated with TiCl₄ can increase the surface area of TiO₂ nanotubes, resulting in the increase of dye adsorption and have great help for the increase of the conversion efficiency of DSSCs.     

Enhanced photoelectric efficiency by surface modification of TiO<Subscript>2</Subscript> thin film using various acidic species

This study examined the photoelectric conversion efficiency of the dye-sensitized solar cell (DSSC) when the surface of a nanometer-sized TiO₂ film, which was prepared using the solvothermal method, was modified by five acid compounds. The TiO₂ film exhibited an anatase structure with an average particle size in the range of 10–15 nm, and the maximum absorption band was shown in the UV-visible spectrum around 360 nm. The surface colors of the carboxylic acid-modified TiO₂ films were changed to light or dark with differing energy conversion efficiencies. Particularly, the conversion efficiency was considerably enhanced from approximately 6.25% for the non-modified TiO₂ film to approximately 7.50% for the film treated by acetic acid of 1.0 mole, with the N719 dye under 100 mW/cm² of simulated sunlight. FT-IR analysis of the films after N719 dye adsorption confirmed that the IR spectrum of the modified TiO₂ showed a sharp and strong band at 500 cm⁻¹, which was assigned to a metal-O bond, due to the formation of a new Ti-O bond between the O of COO⁻ and the Ti atom, which was relatively weaker in the non-modified TiO₂. Furthermore, these results were in agreement with an electrostatic force microscopy (EFM) study showing that the electrons were transferred rapidly to the surface of the acetic acid-modified TiO₂ film, compared with that on the nonmodified TiO₂ film.     

A natural tomato slurry as a photosensitizer for dye-sensitized solar cells with TiO2/CuO composite thin films

We have studied the performance of dye-sensitized solar cells by employing natural dye “anthocyanins” extracted from the tomato slurry as a sensitizer for the TiO₂/CuO photoanode. The extracts were anchored on TiO₂/CuO films deposited on an ITO substrate which was used as a photoanode. The dye adsorbed TiO₂/CuO films electrode, the copper plate as a counter electrode, and iodolyte as an electrolyte were assembled into DSSCs. The conversion efficiency of the DSSCs was found to be 2.96% with a V_OC of 0.615 V, J_SC of 6.6 mA/cm², and an FF of 0.73. This work highlights the use of contribution of the tomato slurry as a natural sensitizer to enhance the efficiency of DSSCs.     

The influence of anatase-rutile mixed phase and ZnO blocking layer on dye-sensitized solar cells based on TiO2nanofiberphotoanodes

High performance is expected in dye-sensitized solar cells (DSSCs) that utilize one-dimensional (1-D) TiO₂ nanostructures owing to the effective electron transport. However, due to the low dye adsorption, mainly because of their smooth surfaces, 1-D TiO₂ DSSCs show relatively lower efficiencies than nanoparticle-based ones. Herein, we demonstrate a very simple approach using thick TiO₂ electrospun nanofiber films as photoanodes to obtain high conversion efficiency. To improve the performance of the DSCCs, anatase-rutile mixed-phase TiO₂ nanofibers are achieved by increasing sintering temperature above 500°C, and very thin ZnO films are deposited by atomic layer deposition (ALD) method as blocking layers. With approximately 40-μm-thick mixed-phase (approximately 15.6?wt.% rutile) TiO₂ nanofiber as photoanode and 15-nm-thick compact ZnO film as a blocking layer in DSSC, the photoelectric conversion efficiency and short-circuit current are measured as 8.01% and 17.3?mA?cm^?2, respectively. Intensity-modulated photocurrent spectroscopy and intensity-modulated photovoltage spectroscopy measurements reveal that extremely large electron diffusion length is the key point to support the usage of thick TiO₂ nanofibers as photoanodes with very thin ZnO blocking layers to obtain high photocurrents and high conversion efficiencies.     

Fabrication and photoelectrochemical properties of TiO2 films on Ti substrate for flexible dye-sensitized solar cells

The dye-sensitized solar cells (DSSCs) using Ti foil supporting substrate for fabricating nanocrystalline TiO₂ flexible film electrodes were developed, intending to improve the photoelectrochemical properties of flexible substrate-based DSSCs. The obtained cells were characterized by electrochemical impedance spectra (EIS), open circuit voltage decay (OCVD) measurement and Tafel plots. The experimental results indicate that the most important advantage of a Ti foil-based TiO₂ flexible electrode over a FTO glass-based electrode lies in its reduced sheet resistance, electron traps, and the retarded back reaction of electrons with tri-iodine ions in DSSCs. All above characteristics for the Ti substrate TiO₂ films are beneficial for decreasing the charge recombination in the TiO₂ electrode and prolonging the electron lifetimes for the DSSCs, as well as improvement of the overall solar conversion efficiency. The photocurrent of the cell fabricated with the Ti foil-based flexible electrode increased significantly, leading to a much higher overall solar conversion efficiency of 5.45% at 100 mW/cm² than the cell made with FTO glass-based TiO₂ electrodes. Above results demonstrate that Ti foil is a potential alternative to the conventional FTO glass substrate for the DSSCs.     

Dye sensitized CO<Subscript>2</Subscript> reduction over pure and platinized TiO<Subscript>2</Subscript>

TiO₂ thin and thick films promoted with platinum and organic sensitizers including novel perylene diimide dyes (PDI) were prepared and tested for carbon dioxide reduction with water under visible light. TiO₂ films were prepared by a dip coating sol–gel technique. Pt was incorporated on TiO₂ surface by wet impregnation [Pt(on).TiO₂], or in the TiO₂ film [Pt(in).TiO₂] by adding the precursor in the sol. When tris (2,2′-bipyridyl) ruthenium(II) chloride hexahydrate was used as sensitizer, in addition to visible light activity towards methane production, H₂ evolution was also observed. Perylene diimide derivatives used in this study have shown light harvesting capability similar to the tris (2,2′-bipyridyl) ruthenium(II) chloride hexahydrate.     

The Effects of Co-Sensitization and Electronic Structure of Nanocrystalline N/TiO<Subscript>2</Subscript> Anode on the Performance of Dye-Sensitized Solar Cells

N/TiO₂ nanocrystalline film anodes were obtained by doping nonmetallic element N which could change the LUMO of anode. This paper also studied the match between the LUMO energy lever of N/TiO₂ anode and the dye, which led to the easy injection of electron from the excited state of dye molecule to the conduction band of semiconductor, and thus improved the photoelectric conversion efficiency and reduced the impedance of solar cells. The solar cell based on N/TiO₂ anode film co-sensitized by P3HT (poly(3-hexylthiophene))/N719(RuL2(NCS)2:2TBA (L = 2,2′-bipyridyl-4,4′-dicarboxylic acid)), the absorption region of which covered the entire visible region in solar cells, showed a short-circuit current density of 6.88 mA cm⁻², an open-circuit voltage of 0.616 V, and a photoelectric conversion efficiency of 2.34%.     

Enhancing the performance of dye-sensitized solar cells based on an organic dye by incorporating TiO2 nanotube in a TiO2 nanoparticle film

The photoelectrochemical properties of a high molar extinction coefficient charge transfer organic dye containing thienylfluorene segment called FL, and the effect of incorporating TiO₂ nanotube (TiNT) in TiO₂ nanoparticle film along with the above dye on the photovoltaic performance of dye-sensitized solar cells (DSSCs) were investigated. The influence of soaking time of the TiO₂ electrode in dye solution and the effect of varying its concentration, on the solar cell efficiency was also studied. Cyclic voltammetric (CV) analysis revealed the linear relationship between the anodic peak current and the scan rate, indicating a surface-confined diffusion process.The surface morphology of TiNT was characterized using SEM, TEM and XRD. The open-circuit voltage (V_OC) of the DSSC increased with the increase in the wt% of TiNT and shows optimal value at about 5 wt%, which is correlated with the suppression of the electron recombination as found out from the electron lifetime studies.The electrochemical impedance spectroscopy (EIS) technique was employed to quantify the charge transport resistance (R_ct) and electron lifetime under different ratios of the TiNT/nanoparticle. The electron lifetimes of the DSSCs based on FL and N3 dye were very close to one another and the DSSC based on the FL showed respectable photovoltaic performance of ca. 7.8% under the light intensity of 100 mW cm⁻² (AM 1.5G).     

Photo-Generated Activities of Nanocrystalline TiO<Subscript>2</Subscript> Thin Films

Transparent nanocrystalline TiO₂ thin films with high photocatalytic activity and photo-induced wettability were successfully deposited on a glass slide. Crystal phase transformations and particle size of TiO₂ were investigated. Structural and morphological properties of the films were investigated. The photocatalytic activity of the TiO₂ films was evaluated. It is found that the photocatalytic activity of TiO₂ thin films is significantly decreased by increasing the annealing temperature, which results in a decrease in BET surface area and an increase in crystal size. In addition, increasing film thickness within a certain range significantly improves the photocatalytic activity without causing crack formation of the TiO₂ films. Photocatalytic oxidation and photo-induced wettability conversion on the films were investigated. It is found that photo-induced hydrophilic conversion is observed even on the samples annealed at high temperature. The best photo-generated activities are obtained by optimization of dip-coating cycles and annealing temperatures.     

Dye-sensitized solar cells based on double-layered TiO2 composite films and enhanced photovoltaic performance

Dye-sensitized solar cells (DSSCs) are fabricated based on double-layered composite films of TiO₂ nanoparticles and hollow spheres. The photoelectric conversion performances of DSSCs based on nanoparticles/nanoparticles (PP), hollow spheres/hollow spheres (HH), hollow spheres/nanoparticles (HP), and nanoparticles/hollow spheres (PH) double-layered films are investigated, and their photo-electric conversion efficiencies are 4.33, 4.72, 4.93 and 5.28%, respectively. The enhanced performance of TiO₂ nanoparticles/hollow spheres double-layered composite film solar cells can be attributed to the combined effect of following factors. The light scattering of overlayer hollow spheres enhances harvesting light of the DSSCs and the underlayer TiO₂ nanoparticle layer ensures good electronic contact between film electrode and the F-doped tin oxide (FTO) glass substrate. Furthermore, the high surface areas and pore volume of TiO₂ hollow spheres are respectively beneficial to adsorption of dye molecules and transfer of electrolyte solution.     

Optimization of the dye-sensitized solar cell performance by mechanical compression

In this study, the P25 titanium dioxide (TiO₂) nanoparticle (NP) thin film was coated on the fluorine-doped tin oxide (FTO) glass substrate by a doctor blade method. The film then compressed mechanically to be the photoanode of dye-sensitized solar cells (DSSCs). Various compression pressures on TiO₂ NP film were tested to optimize the performance of DSSCs. The mechanical compression reduces TiO₂ inter-particle distance improving the electron transport efficiency. The UV–vis spectrophotometer and electrochemical impedance spectroscopy (EIS) were employed to quantify the light-harvesting efficiency and the charge transport impedance at various interfaces in DSSC, respectively. The incident photon-to-current conversion efficiency was also monitored. The results show that when the DSSC fabricated by the TiO₂ NP thin film compressed at pressure of 279 kg/cm², the minimum resistance of 9.38 Ω at dye/TiO₂ NP/electrolyte interfaces, the maximum short-circuit photocurrent density of 15.11 mA/cm², and the photoelectric conversion efficiency of 5.94% were observed. Compared to the DSSC fabricated by the non-compression of TiO₂ NP thin film, the overall conversion efficiency is improved over 19.5%. The study proves that under suitable compression pressure the performance of DSSC can be optimized.     

Effect of compressed TiO2 nanoparticle thin film thickness on the performance of dye-sensitized solar cells

In this study, dye-sensitized solar cells (DSSCs) were fabricated using nanocrystalline titanium dioxide (TiO₂) nanoparticles as photoanode. Photoanode thin films were prepared by doctor blading method with 420 kg/cm² of mechanical compression process and heat treatment in the air at 500°C for 30 min. The optimal thickness of the TiO₂ NP photoanode is 26.6 μm with an efficiency of 9.01% under AM 1.5G illumination at 100 mW/cm². The efficiency is around two times higher than that of conventional DSSCs with an uncompressed photoanode. The open-circuit voltage of DSSCs decreases as the thickness increases. One DSSC (sample D) has the highest conversion efficiency while it has the maximum short-circuit current density. The results indicate that the short-circuit current density is a compromise between two conflict factors: enlargement of the surface area by increasing photoanode thickness and extension of the electron diffusion length to the electrode as the thickness increases.     

Two novel hierarchical homogeneous nanoarchitectures of TiO<Subscript>2</Subscript> nanorods branched and P25-coated TiO<Subscript>2</Subscript> nanotube arrays and their photocurrent performances

We report here for the first time the synthesis of two novel hierarchical homogeneous nanoarchitectures of TiO₂ nanorods branched TiO₂ nanotube arrays (BTs) and P25-coated TiO₂ nanotube arrays (PCTs) using two-step method including electrochemical anodization and hydrothermal modification process. Then the photocurrent densities versus applied potentials of BTs, PCTs, and pure TiO₂ nanotube arrays (TNTAs) were investigated as well. Interestingly, at -0.11 V and under the same illumination condition, the photocurrent densities of BTs and PCTs show more than 1.5 and 1 times higher than that of pure TNTAs, respectively, which can be mainly attributed to significant improvement of the light-absorbing and charge-harvesting efficiency resulting from both larger and rougher surface areas of BTs and PCTs. Furthermore, these dramatic improvements suggest that BTs and PCTs will achieve better photoelectric conversion efficiency and become the promising candidates for applications in DSSCs, sensors, and photocatalysis.