Etch characteristics of indium zinc oxide thin films in a C2F6/Ar plasma

Dry etching of indium zinc oxide (IZO) thin films was performed using inductively coupled plasma reactive ion etching in a C₂F₆/Ar gas. The etch characteristics of IZO films were investigated as a function of gas concentration, coil rf power, dc-bias voltage to substrate, and gas pressure. As the C₂F₆ concentration was increased, the etch rate of the IZO films decreased and the degree of anisotropy in the etch profile also decreased. The etch profile was improved with increasing coil rf power and dc-bias voltage, and decreasing gas pressure. An X-ray photoelectron spectroscopy analysis confirmed the formation of InF₃ and ZnF₂ compounds on the etched surface due to the chemical reaction of IZO films with fluorine radicals. In addition, the film surfaces etched at different conditions were examined by atomic force microscopy. These results demonstrated that the etch mechanism of IZO thin films followed sputter etching with the assistance of chemical reaction.     

Inductively coupled plasma reactive ion etching of titanium thin films using a Cl2/Ar gas

Inductively coupled plasma reactive ion etching of titanium thin films patterned with a photoresist using Cl₂/Ar gas was examined. The etch rates of the titanium thin films increased with increasing the Cl₂ concentration but the etch profiles varied. In addition, the effects of the coil rf power, dc-bias voltage and gas pressure on the etch rate and etch profile were investigated. The etch rate increased with increasing coil rf power, dc-bias voltage and gas pressure. The degree of anisotropy in the etched titanium films improved with increasing coil rf power and dc-bias voltage and decreasing gas pressure. X-ray photoelectron spectroscopy revealed the formation of titanium compounds during etching, indicating that Ti films etching proceeds by a reactive ion etching mechanism.     

Dry etch properties of IZO thin films in a CF4/Ar adaptively coupled plasma system

In this study, we investigated to the etch characteristics of indium zinc oxide (IZO) thin films in a CF₄/Ar plasma, namely, etch rate and selectivity toward SiO₂. A maximum etch rate of 76.6 nm/min was obtained for IZO thin films at a gas mixture ratio of CF₄/Ar (25:75%). In addition, etch rates were measured as a function of etching parameters, including adaptively coupled plasma chamber pressure. X-ray photoelectron spectroscopy analysis showed efficient destruction of the oxide bonds by ion bombardment, as well as accumulation of low volatile reaction products on the surface of the etched IZO thin films. Field emission Auger electron spectroscopy analysis was used to examine the efficiency of ion-stimulated desorption of the reaction products.     

Etch characteristics of magnetic tunnel junction stack with nanometer-sized patterns for magnetic random access memory

Etch characteristics of magnetic tunnel junction (MTJ) stack masked with TiN films were investigated using an inductively coupled plasma reactive ion etcher in Cl₂/Ar and BCl₃/Ar gases for magnetic random access memory. The effect of etch gas on the etch profile of MTJ stacks was examined. As Cl₂ and BCl₃ concentrations increased, the etch slope of etched MTJ stack became slanted and the dimensional shrinkage was observed. A high degree of anisotropic etching of MTJ stacks was achieved using Cl₂/Ar gas at the optimized etch conditions.     

High density plasma etching of amorphous CoZrNb films for thin film magnetic devices

Inductively coupled plasma reactive ion etching of CoZrNb magnetic thin films was studied using a TiN hard mask in a Cl₂/O₂/Ar gas mix. The etch rates of CoZrNb films and TiN hard mask gradually decreased with increasing Cl₂ or O₂ gas concentrations. When O₂ gas was added in the Cl₂/Ar gas mix, the etch rate of TiN hard mask was suppressed effectively so that the etch selectivity of CoZrNb film to TiN hard mask was enhanced. The addition of O₂ into the gas mix also led to the anisotropic etching of the CoZrNb films and it was confirmed by Auger electron spectroscopy that there were no redeposited materials on the sidewall of the etched films. Highly anisotropic etching of CoZrNb films was achieved at room temperature under the optimized etching conditions.     

Etch characteristics of FePt magnetic thin films using inductively coupled plasma reactive ion etching

Etch characteristics of L10 FePt thin films masked with TiN films were investigated using an inductively coupled plasma (ICP) reactive ion etching in a CH₃OH/Ar plasma. As the CH₃OH gas was added to Ar, the etch rates of FePt thin films and TiN hard mask gradually decreased, and the etch profile of FePt films improved with high degree of anisotropy. With increasing ICP rf power and dc-bias voltage to substrate and decreasing gas pressure, the etch rate increased and the etch profile becomes vertical without any redepositions or etch residues. Based on the etch characteristics and surface analysis of the films by X-ray photoelectron spectroscopy, it can be concluded that the etch mechanism of FePt thin films in a CH₃OH/Ar gas does not follow the reactive ion etch mechanism but the chemically assisted sputter etching mechanism, due to the chemical reaction of FePt film with CH₃OH gas.     

A study on the etch characteristics of HfAlO3 dielectric thin film in Cl2/Ar gas chemistry using inductively coupled plasma system

Thin films of HfAlO₃, a high-k material, were etched using inductively-coupled plasma. The dry etching mechanism of the HfAlO₃ thin film was studied by varying the Cl₂/Ar gas mixing ratio, RF power, direct current bias voltage, and process pressure. The maximum etch rate of the HfAlO₃ thin film was 16.9 nm/min at a C1₂/(C1₂ + Ar) ratio of 80%. Our results showed that the highest etch rate of the HfAlO₃ thin films was achieved by reactive ion etching using Cl radicals, due to the high volatility of the metal-chlorides. Consequently, the increased chemical effect caused an increase in the etch rate of the HfAlO₃ thin film. Surface analysis by x-ray photoelectron spectroscopy showed evidence that Hf, Al and O reacted with Cl and formed nonvolatile metal-oxide compounds and volatile metal-chlorides. This effect may be related to the concurrence of chemical and physical pathways in the ion-assisted chemical reaction.     

Etch characteristics of IrMn thin films using an inductively coupled plasma of CH3OH/Ar

An inductively coupled plasma reactive ion etching of IrMn magnetic thin films patterned with Ti hard mask was studied in a CH₃OH/Ar gas mix. As the CH₃OH concentration increased, the etch rates of IrMn thin films and Ti hard mask decreased, while the etch profiles improved with high degree of anisotropy. The effects of coil rf power, dc-bias voltage to substrate and gas pressure on the etch characteristics were investigated. The etch rate increased and the etch profile improved with increasing coil rf power, dc-bias voltage and decreasing gas pressure. X-ray photoelectron spectroscopy revealed that the chemical reaction between IrMn films and CH₃OH gas occurred, leading to the clean and good etch profile with high degree of anisotropy of 90°.     

Etch characteristics of TiN/Al2O3 thin film by using a Cl2/Ar adaptive coupled plasma

In this study, we carried out an investigation in the etching characteristics of TiN thin films in a C1₂/Ar adaptive coupled plasma. The maximum etch rate of the TiN thin films was 768 nm/min at a gas mixing ratio of C1₂ (75%)/Ar (25%). At the same time, the etch rate was measured as functions of the various etching parameters. The X-ray photoelectron spectroscopy analysis showed the efficient destruction of the oxide bonds by the ion bombardment as well as the accumulation of low volatile reaction products on the etched surface. Field emission Auger electron spectroscopy analysis was used to examine the efficiency of the ion-stimulated desorption of the reaction products.     

Etch characteristics of TiN/Al2O3 thin film by using a Cl2/Ar adaptive coupled plasma

In this study, we carried out an investigation in the etching characteristics of TiN thin films in a C1₂/Ar adaptive coupled plasma. The maximum etch rate of the TiN thin films was 768 nm/min at a gas mixing ratio of C1₂ (75%)/Ar (25%). At the same time, the etch rate was measured as functions of the various etching parameters. The X-ray photoelectron spectroscopy analysis showed the efficient destruction of the oxide bonds by the ion bombardment as well as the accumulation of low volatile reaction products on the etched surface. Field emission Auger electron spectroscopy analysis was used to examine the efficiency of the ion-stimulated desorption of the reaction products.     

The dry etching property of TiO2 thin films using metal-insulator-metal capacitor in inductively coupled plasma system

In this work, we investigated the etching characteristics of TiO₂ thin films and the selectivity of TiO₂ to SiO₂ in a BCl₃/Ar inductively coupled plasma (ICP) system. The maximum etch rate of 84.68 nm/min was obtained for TiO₂ thin films at a gas mixture ratio of BCl₃/Ar (25:75%). In addition, etch rates were measured as a function of etching parameters, such as the RF power, DC-bias voltage and process pressure. Using the X-ray photoelectron spectroscopy analysis the accumulation of chemical reaction on the etched surface was investigated. Based on these data, the ion-assisted physical sputtering was proposed as the main etch mechanism for the BCl₃-containing plasmas.     

Characteristics of GaN thin films by inductively coupled plasma etching with Cl2/BCl3 and Cl2/Ar

GaN thin films were etched by inductively coupled plasma (ICP). The effects of BCl₃ and Ar with different Cl₂ fraction are studied and compared. The ICP power and RF power are also altered to investigate the different effects by using Cl₂/BCl₃ or Cl₂/Ar as etching gases. The etch rate and surface morphology of the etched surface are characterized by using surface profiler, scanning electron microscopy and atomic force microscopy. The root-mean-square roughness values are systematically compared. It is found that the etch rates of Cl₂/Ar are higher than that of the Cl₂/BCl₃ in the Cl₂ fraction ranging from 10 to 90%. When the ICP power is increased, the RMS roughness of GaN surface after ICP etching shows reverse trend between Cl₂/BCl₃ and Cl₂/Ar gas mixture. The results indicate quite different features using Cl₂/BCl₃ and Cl₂/Ar for GaN ICP etcing under the same conditions.     

Evolution of etch profile in etching of CoFeB thin films using high density plasma reactive ion etching

Inductively coupled plasma reactive ion etching of CoFeB magnetic thin films patterned with Ti hard mask was studied in a CH₃OH/Ar gas mix. As the CH₃OH concentration increased, the etch rates of CoFeB thin films and Ti hard mask decreased but the etch profiles improved with high degree of anisotropy. The effects of coil rf power, dc-bias voltage and gas pressure on the etch characteristics were investigated. The etch rate increased with increasing coil rf power, dc-bias voltage and decreasing gas pressure. The degree of anisotropy in the etch profile of CoFeB films improved with increasing coil rf power and dc-bias voltage. X-ray photoelectron spectroscopy revealed that the chemical compounds containing Co and Fe components were formed during the etching. However, it was expected that the formation of these compounds could not increase the etch rates of the films due to low volatile compounds despite the improvement in etch profile.     

Investigation on etch characteristics of MgO thin films using a HBr/Ar plasma

Etch characteristics of MgO thin films were investigated using an inductively coupled plasma reactive ion etcher in a HBr/Ar plasma. As the concentration of HBr gas increased, the etch rate of MgO thin films gradually decreased, but the etch rate of Ti hard mask showed initial decrease and then increased with increasing HBr concentration. The etch profile of MgO films was improved with increasing HBr concentration and a high degree of anisotropy in etch profile was achieved at 30% HBr/Ar gas. Based on the etch characteristics and surface analysis by X-ray photoelectron spectroscopy, it can be concluded that the etch mechanism of MgO thin films in a HBr/Ar gas does not follow the reactive ion etch mechanism but the sputter etching mechanism with the assistance of chemical reactions on the film surfaces.     

Etch characteristics of HfO2 thin films by using CF4/Ar inductively coupled plasma

In this study, we carried out an investigation of the etching characteristics (etch rate, selectivity) of HfO₂ thin films in the CF₄/Ar inductively coupled plasma (ICP). The maximum etch rate of 54.48 nm/min for HfO₂ thin films was obtained at CF₄/Ar (=20:80%) gas mixing ratio. At the same time, the etch rate was measured as function of the etching parameters such as ICP RF power, DC-bias voltage, and process pressure. The X-ray photoelectron spectroscopy analysis showed an efficient destruction of the oxide bonds by the ion bombardment as well as an accumulation of low volatile reaction products on the etched surface. Based on these data, the chemical reaction was proposed as the main etch mechanism for the CF₄-containing plasmas.     

HfO2 etching mechanism in inductively-coupled Cl2/Ar plasma

Etching characteristics and the mechanism of HfO₂ thin films in Cl₂/Ar inductively-coupled plasma were investigated. The etch rate of HfO₂ was measured as a function of the Cl₂/Ar mixing ratio in the range of 0 to 100% Ar at a fixed gas pressure (6 mTorr), input power (700 W), and bias power (300 W). We found that an increase in the Ar mixing ratio resulted in a monotonic decrease in the HfO₂ etch rate in the range of 10.3 to 0.7 nm/min while the etch rate of the photoresist increased from 152.1 to 375.0 nm/min for 0 to 100% Ar. To examine the etching mechanism of HfO₂ films, we combined plasma diagnostics using Langmuir probes and quadrupole mass spectrometry with global (zero-dimensional) plasma modeling. We found that the HfO₂ etching process was not controlled by ion-surface interaction kinetics and formally corresponds to the reaction rate-limited etch regime.     

Etch damage characteristics of TiO2 thin films by capacitively coupled RF Ar plasmas

Etch damage of TiO₂ thin films with the anatase phase by capacitively coupled RF Ar plasmas has been investigated. The plasma etching causes a mixed phase of anatase and rutile or the rutile phase. The effect of Ar plasma etching damage on degenerating TiO₂ thin films is dependent on gas pressure and etching time. The physical etching effect at a low gas pressure (1.3 Pa) contributes to the degradation: the atomic O concentration at the thin film surface is strongly increased. At a high gas pressure (13-27 Pa) and long etching time (60 min), there are a variety of surface defects or pits, which seem to be similar to those for GaN resulting from synergy effect between particle and UV radiation from the plasmas. For the hydrophilicity, the thin film etched at the high gas pressure and a short etching time (5 min) seems to have no etch damage: its contact angle property is almost similar to that for the as-grown thin film, and is independent of the black light irradiation. This result would probably result from formation of donor-like surface defects such as oxygen vacancy.     

Inductively coupled plasma reactive ion etching of ZnO films in HBr/Ar plasma

The etching characteristics of ZnO thin films were examined in an HBr/Ar gas mix using an inductively coupled plasma reactive ion etching system. The etch rate and etch profile were systematically investigated as a function of gas concentration. In addition, the effects of etch parameters such as coil rf power, dc-bias voltage, and gas pressure were studied. As the HBr concentration increased, the etch rate of the ZnO films gradually decreased while the etch profile was improved. Surface analyses including X-ray photoelectron spectroscopy and atomic force microscopy were employed to elucidate the etch mechanism of ZnO in an HBr/Ar chemistry.     

Etch characteristics of CoFeB magnetic thin films using high density plasma of a H2O/CH4/Ar gas mixture

Etch characteristics of CoFeB magnetic thin films patterned with TiN hard masks were investigated using inductively coupled plasma reactive ion etching in H₂O/Ar and H₂O/CH₄ gas mixes. As the H₂O concentration in the H₂O/Ar gas increased, the etch rates of CoFeB and TiN films decreased simultaneously, while the etch selectivity increased and etch profiles improved slightly without any redeposition. The addition of CH₄ to the H₂O gas resulted in an increase in etch selectivity and a higher degree of anisotropy in the etch profile. X-ray photoelectron spectroscopy was performed to understand the etch mechanism in H₂O/CH₄ plasma. A good pattern transfer of CoFeB films masked with TiN films was successfully achieved using the H₂O/CH₄ gas mix.     

Surface properties of etched ITO thin films using high density plasma

The etching characteristics of ITO in a BCl₃/Ar plasma, including the etch rate and selectivity of ITO, were investigated. The maximum etch rate of 62.8 nm/min for the ITO thin films was obtained at a BCl₃/Ar gas mixing ratio of 25%/75%. Ion bombardment by physical sputtering was required to obtain such high etch rates, due to the relatively low volatility of the by-products formed during the etching. The chemical reactions on the etched surfaces were investigated using X-ray Photoelectron Spectroscopy (XPS) and the preferential losses on the etched surfaces were investigated using Atomic Force Microscopy (AFM).