Determination of photo-catalytic activity of un-doped and Mn-doped TiO2 anatase powders on acetaldehyde under UV and visible light

Titanium dioxide (TiO₂) photocatalytic powder materials doped with various levels of manganese (Mn) were synthesized to be used as additives to wall painting in combating indoor and outdoor air pollution. The heterogeneous photocatalytic degradation of gaseous acetaldehyde (CH₃CHO) on Mn-TiO₂ surfaces under ultraviolet and visible (UV/Vis) irradiation was investigated, by employing the Photochemical Static Reactor coupled with Fourier-Transformed Infrared spectroscopy (PSR/FTIR) technique. Experiments were performed by exposing acetaldehyde (~ 400 Pa) and synthetic air mixtures (~ 1.01 × 10⁵ Pa total pressure) on un-doped TiO₂ and doped with various levels of Mn (0.1-33% mole percentage) under UV and visible irradiation at room temperature. Photoactivation was initiated using either UV or visible light sources with known emission spectra. Initially, the photo-activity of CH₃CHO under the above light sources, and the physical adsorption of CH₃CHO on Mn-TiO₂ samples in the absence of light were determined prior to the photocatalytic experiments. The photocatalytic loss of CH₃CHO on un-doped TiO₂ and Mn-TiO₂ samples in the absence and presence of UV or visible irradiation was measured over a long time period (≈ 60 min), to evaluate their relative photocatalytic activity. The gaseous photocatalytic end products were also determined using absorption FTIR spectroscopy. Carbon dioxide (CO₂) was identified as the main photocatalysis product. It was found that 0.1% Mn-TiO₂ samples resulted in the highest photocatalytic loss of CH₃CHO under visible irradiation. This efficiency was drastically diminished at higher levels of Mn doping (1-33%). The CO₂ yields were the highest for 0.1% Mn-TiO₂ samples under UV irradiation, in agreement with the observed highest CH₃CHO decomposition rates. It was demonstrated that low-level (0.1%) doping of TiO₂ with Mn results in a significant increase of their photocatalytic activity in the visible range, compared to un-doped TiO₂. This elevated activity is lost at high doping levels (1-33%). Finally, the photocatalytic degradation mechanism of CH₃CHO on 0.1% Mn-TiO₂ surfaces under visible irradiation leading to low CO₂ yields is different than that under UV irradiation resulting to high CO₂ yields.     

Photocatalytic activity of pulsed laser deposited TiO2 thin films in N2, O2 and CH4

We report on pulsed laser deposition of TiO₂ films on glass substrates in oxygen, methane, nitrogen and mixture of oxygen and nitrogen atmosphere. The nitrogen incorporation into TiO₂ lattice was successfully achieved, as demonstrated by optical absorption and XPS measurements. The absorption edge of the N-doped TiO₂ films was red-shifted up to ∼ 480 nm from 360 nm in case of undoped ones.The photocatalytic activity of TiO₂ films was investigated during toxic Cr(VI) ions photoreduction to Cr(III) state in aqueous media under irradiation with visible and UV light. Under visible light irradiation, TiO₂ films deposited in nitrogen atmosphere showed the highest photocatalytic activity, whereas by UV light exposure the best results were obtained for the TiO₂ structures deposited in pure methane and oxygen atmosphere.     

Efficient SiO2/WO3–TiO2@rGO nanocomposite photocatalyst for visible-light degradation of colored pollutant in water

The photoactive SiO₂/WO₃–TiO₂@rGO nanocomposite was fabricated through sol–gel, microwave, and hydrothermal approaches for the photodegradation of methylene blue (MB) as an organic-colored pollutant. The nanocomposite photocatalysts were formulated by adjustment of the ingredients content to achieve efficient synergic effects on photocatalyst performance. The results exhibited that optimum amount of SiO₂ and rise in WO₃/TiO₂ ratio as well as incorporation of reduced graphene oxide in structure can be led to further efficiency of degradation under visible light. The effect of sunlight irradiation, pH of MB solution, MB concentration, and lamp distance on photodegradation reaction were also investigated. The best performance about 99.9% MB degradation was obtained based on using 0.3 g/L of optimum photocatalyst to remove the 5 ppm MB solution with pH of 5.41 during 3 h irradiation by visible-light source with 30 cm distance from MB solution. As well, results showed that photocatalyst performance under visible light is better than sunlight irradiation. The most favorable photocatalyst indicated surface area of 60.9 m²/g. Furthermore, the reusability test indicated a proper activity after three cycles under the same conditions. So, the introduced efficient visible photoactive SiO₂/WO₃–TiO₂@rGO nanocomposite can be considered as an appropriate potential to remove organic pollutants in colored effluents.

     

Removal of fluoride from aqueous solution by polypyrrole/Fe3O4 magnetic nanocomposite

Highly efficient visible light TiO₂ photocatalyst was prepared by the sol-gel method at lower temperature (≤300 °C), and characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), Fourier-transform infrared spectroscopy (FTIR), UV-vis diffuse reflectance spectroscopy (UV-vis DRS), X-ray photoelectron spectroscopy (XPS), Raman spectroscopy and differential scanning calorimetry-thermogravimetric analysis (DSC-TGA). The effects of the heat treatment temperature and time of the as-prepared TiO₂ on its visible light photocatalytic activity were investigated by monitoring the degradation of methyl orange solution under visible light irradiation (wavelength ≥ 400 nm). Results show that the as-prepared TiO₂ nanoparticles possess an anatase phase and mesoporous structure with carbon self-doping and visible photosensitive organic groups. The visible light photocatalytic activity of the as-prepared TiO₂ is greatly higher than those of the commercial TiO₂ (P-25) and other visible photocatalysts reported in literature (such as PPy/TiO₂, P3HT/TiO₂, PANI/TiO₂, N-TiO₂ and Fe³⁺-TiO₂) and its photocatalytic stability is excellent. The reasons for improving the visible light photocatalytic activity of the as-prepared TiO₂ can be explained by carbon self-doping and a large amount of visible photosensitive groups existing in the as-prepared TiO₂. The apparent optical thickness (τ_app), local volumetric rate of photo absorption (LVRPA) and kinetic constant (k_T) of the photodegradation system were calculated.     

Synthesis of TiO2 nanotubes coupled with CdS nanoparticles and production of hydrogen by photocatalytic water decomposition

The CdS/TiO₂NTs composite was prepared by a simple two-step chemical solution routes to directly transfer trititanate nanotubes to TiO₂NTs and simultaneously coupled with CdS nanoparticles. The results of XRD, TEM, Diffuse reflectance UV-Visible absorption spectra revealed that the CdS nanoparticles were homogeneously embedded on the surface of TiO₂NTs and the absorption spectrum of TiO₂NTs was extended to visible region. The activity of hydrogen production by photocatalytic water decomposition for the CdS/TiO₂NTs composite was examined under visible light irradiation (λ > 400 nm) and the quantity of H₂ evolution was ca. 1708 μL/g for 6 h.     

Dye-sensitized TiO2 film with bifunctionalized zones for photocatalytic degradation of 4-cholophenol

A new strategy to photocatalytic degradation of 4-cholophenol (4-CP) under visible light irradiation was described. The TiO₂ film deposited on an ordinary glass sheet was distributed into two zones. One zone was sensitized by N719 dye and fabricated to be a sandwich type cell with a similar structure of dye-sensitized solar cells. The other zone was inserted into pollutants solution for degradation. A highly oxidized overvoltage anode was achieved from the dye-sensitized zone. The bifunctionalized TiO₂ film and the anode could degrade 4-chlorophenol in two separate reactors with 97% and 96% removal of 4-CP after 5 h, respectively. The degradation efficiency could be improved by addition of FeSO₄. The as-prepared bifunctionalized TiO₂ film was comparably stable in the process of degradation.     

Synthesis and photocatalytic performance of novel CdS quantum dots sensitized Bi2WO6 photocatalysts

Novel quantum dots sensitized CdS-Bi₂WO₆ composite photocatalysts were synthesized to improve the visible-light-driven photocatalytic performance. The products were characterized by X-ray diffraction (XRD), scanning electron microscopy (FE-SEM), transmission electron microscopy (TEM) UV-vis diffuse reflectance spectra (DRS). The photocatalytic activities of QDs sensitized CdS-Bi₂WO₆ samples were investigated based on the decomposition of methyl orange under visible light irradiation (λ > 420 nm). The DRS results revealed that CdS-Bi₂WO₆ samples have a red shift and stronger absorption in the visible light region. After being sensitized by quantum dots CdS, the Bi₂WO₆ samples showed the high efficiency for the degradation of methyl orange. This study may provide an approach to treatment of organic pollutants by using visible light.     

Photocatalytic degradation of RhB over MgFe2O4/TiO2 composite materials

MgFe₂O₄/TiO₂ (MFO/TiO₂) composite photocatalysts were successfully synthesized using a mixing-annealing method. The synthesized composites exhibited significantly higher photocatalytic activity than a naked semiconductor in the photodegradation of Rhodamine B. Under UV and visible light irradiation, the optimal percentages of doped MgFe₂O₄ (MFO) were 2 wt.% and 3 wt.%, respectively. The effects of calcination temperature on photocatalytic activity were also investigated. The origin of the high level of activity was discussed based on the results of X-ray diffraction, UV-vis diffuse reflection spectroscopy, scanning electron microscopy, transmission electron microscopy, and nitrogen physical adsorption. The enhanced activity of the catalysts was mainly attributed to the synergetic effect between the two semiconductors, the band potential of which matched suitably.     

Solar photocatalytic degradation of 2-sec-butyl-4,6-dinitrophenol (DNBP) using TiO2/SiO2 aerogel composite photocatalysts

Silica aerogels and TiO₂/silica aerogel composite photocatalysts were synthesized by sol–gel technique at ambient pressure using orthosilioate and tetra-n-butyl titanate as precursors, respectively. The prepared composite photocatalysts were characterized by XRD, TEM, BET surface area, FT-IR and UV–vis absorption spectra. The results showed that the TiO₂/silica aerogel composite photocatalysts possess high surface area. The addition of silica aerogels inhibited the grain growth and phase transformation of anatase to rutile during calcination. The TiO₂/silica aerogel composite sample calcined at 500 °C with an optimal silica aerogel content of 7 wt.% afforded the highest photocatalytic activity. The photocatalytic degradation of 2-sec-butyl-4,6-dinitrophenol (DNBP) was investigated by using this novel TiO₂/silica aerogel composite photocatalyst under solar light irradiation. The effects of irradiation time, pH, catalyst concentration, temperature and initial DNBP concentration were examined as operational parameters. The optimal operational parameters were found as follows: pH as solution pH 4.82, 8 g L⁻¹ catalyst concentration, 20 °C, and 240 min irradiation time. The kinetics of DNBP degradation by TiO₂/silica aerogel composite fit well a pseudo-first-order kinetic model. The repeatability of photocatalytic activity was also tested. This study showed the feasible and potential use of TiO₂/silica aerogel composite photocatalysts in degradation of toxic organic contaminants.     

Photocatalytic degradation of phenol in aqueous solutions by Pr-doped TiO2 nanoparticles

Photocatalytic degradation of phenol in water was examined using Pr-doped TiO₂ nanoparticles. These photocatalysts were synthesized by an acid-peptized sol–gel method from titanium tetra-isopropoxide with different concentrations of Pr(III) dopant and calcination temperatures. Several tools such as XRD, BET surface area, SEM, and EDX, were used to evaluate particle structure, size distribution, and composition. The optical absorption properties of the prepared particles were also measured. Photocatalytic activity of the particles was studied in a batch reactor containing phenol solution with 400 W UV irradiation. Parameters affecting photocatalytic process such as the catalyst crystallinity, light absorption efficiency, the dosage of catalyst, dopant and phenol concentrations were investigated. The Pr-doped TiO₂ showed high activity for photocatalytic degradation of phenol. The presence of Pr ions in the TiO₂ particles would cause a significant absorption shift towards the visible region. The degradation process was optimized using 1 g/L Pr-doped TiO₂ with a Pr(III) concentration of 0.072 mol% after 2 h irradiation. It was shown that photodegradation followed a pseudo-first-order kinetics and the rate constant changed with phenol concentration.     

Visible light absorption ability and photocatalytic oxidation activity of various interstitial N-doped TiO2 prepared from different nitrogen dopants

Nitrogen-doped TiO₂ was developed to enable photocatalytic reactions using the visible range of the solar spectrum. This work reports on the synthesis, characterisation and kinetic study of interstitial N-doped TiO₂ prepared by the sol–gel method using three different types of nitrogen dopants: diethanolamine, triethylamine and urea. X-ray diffraction, scanning electron microscopy, transmission electron microscopy, X-ray photoelectron spectroscopy and UV–visible spectroscopy were used to analyse the titania. Different interstitial N-doped TiO₂ properties, such as absorption ability in the UV–visible light region, redshift in adsorption edge, good crystallisation and composition ratio of titania structures (anatase and rutile) could be obtained from different nitrogen dopants. Amongst investigated nitrogen precursors, diethanolamine provided the highest visible light absorption ability of interstitial N-doped TiO₂ with the smallest energy bandgap and the smallest anatase crystal size, resulting in the highest efficiency in 2-chlorophenol degradation. The photocatalytic activity of all N-doped TiO₂ can be arranged in the following order: TiO₂/diethanolamine > TiO₂/triethylamine > TiO₂/urea > un-doped TiO₂. The initial rate of 2-chlorophenol degradation using the interstitial N-doped TiO₂ with diethanolamine was 0.59 mg/L-min and the kinetic constant was 2.34 × 10⁻² min⁻¹ with a half-life of 98 min. In all cases, hydroquinone was detected as a major intermediate in the degradation of 2-chlorophenol.     

The enhanced visible light photocatalytic activity of nanosheet-like Bi2WO6 obtained by acid treatment for the degradation of rhodamine B

Bi₂WO₆ samples were fabricated by chemical solution decomposition (CSD) method and nanosheet-like Bi₂WO₆ samples could be obtained by concentrated nitric acid treatment at 70 °C for 20 min. The products were characterized by X-ray diffraction (XRD), field emission scanning electron microscopy (FESEM), and UV-vis diffuse reflectance spectra. Photocatalytic activities of the samples were evaluated by the degradation of rhodamine B (RhB) under visible light irradiation. The temperature of acid treatment obviously influenced morphology and the visible light photocatalytic activity of the Bi₂WO₆ samples. The nanosheet-like Bi₂WO₆ photocatalysts obtained by acid treatment exhibited the highest photocatalytic activity under visible light irradiation.     

Photocatalytic properties of porous TiO2/Ag thin films

In this study, nanocrystalline TiO₂/Ag composite thin films were prepared by a sol-gel spin-coating technique. By introducing polystyrene (PS) spheres into the precursor solution, porous TiO₂/Ag thin films were prepared after calcination at a temperature of 500 °C for 4 h. Three different sizes (50, 200, and 400 nm) of PS spheres were used to prepare porous TiO₂ films. The as-prepared TiO₂ and TiO₂/Ag thin films were characterized by X-ray diffractometry (XRD) and by scanning electron microscopy to reveal structural and morphological differences. In addition, the photocatalytic properties of these films were investigated by degrading methylene blue under UV irradiation.When PS spheres of different sizes were introduced after calcination, the as-prepared TiO₂ films exhibited different porous structures. XRD results showed that all TiO₂/Ag films exhibited a major anatase phase. The photodegradation of porous TiO₂ thin films prepared with 200 nm PS spheres and doped with 1 mol% Ag exhibited the best photocatalytic efficiency where ∼ 100% methylene blue was decomposed within 8 h under UV exposure.     

A facile decoration of anatase Fe3O4/TiO2 nanocomposite with graphene quantum dots: Synthesis,characterization, and photocatalytic activity

A combination of electron-rich graphene quantum dots (GQDs) with Fe₃O₄/TiO₂ nanocomposites may develop an efficient electron transfer for enhanced photocatalytic activity. In this report, a facile decoration of GQDs with maltose precursor was synthesized and loaded onto magnetic anatase TiO₂ nanocomposites under hydrothermal methods. The as-synthetized magnetic TiO₂/GQDs nanocomposite resulted in a specific surface area of 38.00 m²/g and a total pore volume of 0.186 cm³/g. The HRTEM images showed a lattice plane distance of 0.350 nm related to the interplanar spacing of the anatase TiO₂ (1 0 1) plane and that of 0.299 nm observed for the in-plane lattice part of GQDs. The effects of magnetic loading ratio and GQDs loading onto TiO₂, pH, photocatalyst dosage, and methylene blue (MB) concentration were thoroughly evaluated to find the optimum conditions of mineralization MB for getting the highest photocatalytic efficiency. The removal efficiency of around 86.08 ± 3.62% was obtained at pH11, photocatalytic dose 400 mg/100 mL, and MB concentration 10 mg/L. Moreover, the photogenerated electron transfers and MB degradation mechanism by the resulting Fe₃O₄/TiO₂/GQD_S under irradiation of UVA light are proposed. The as-synthesized material improved meaningfully greater photocatalytic efficiency for degrading MB under UVA light irradiation than merely pure anatase TiO₂. Also, the predominant mechanism of MB degradation was direct oxidative decomposition through the photogenerated holes. The photocatalytic destruction of MB complied with the apparent first-order models under UVA light irradiation.     

NO treated TiO2 as an efficient visible light photocatalyst for NO removal

In this study, we report that nitrogen doped TiO₂ could be achieved via thermal treatment of Degussa P25 TiO₂ in NO atmosphere directly (P25-NO). The samples were characterized with XRD, XPS, and FT-IR. The characterization results suggested that nitrogen species were interstitially doped in P25-NO during the NO thermal treatment process. In comparison with P25, the P25-NO exhibited significantly enhanced photocatalytic activities under visible light irradiation (λ > 420 nm) for gaseous NO removal. On the basis of electronic band structure theory, we proposed a possible mechanism for the enhanced visible light driven photocatalytic oxidation process over the interstitial N doping P25-NO samples. This work could not only deepen understanding of the enhanced photoactivity originated from interstitial N doping in TiO₂, but also provide a facile route to prepare nitrogen doped TiO₂ for environmental and energy applications.     

Enhanced Photocatalytic Performances of CeO2/TiO2 Nanobelt Heterostructures

CeO₂/TiO₂ nanobelt heterostructures are synthesized via a cost‐effective hydrothermal method. The as‐prepared nanocomposites consist of CeO₂ nanoparticles assembled on the rough surface of TiO₂ nanobelts. In comparison with P25 TiO₂ colloids, surface‐coarsened TiO₂ nanobelts, and CeO₂ nanoparticles, the CeO₂/TiO₂ nanobelt heterostructures exhibit a markedly enhanced photocatalytic activity in the degradation of organic pollutants such as methyl orange (MO) under either UV or visible light irradiation. The enhanced photocatalytic performance is attributed to a novel capture–photodegradation–release mechanism. During the photocatalytic process, MO molecules are captured by CeO₂ nanoparticles, degraded by photogenerated free radicals, and then released to the solution. With its high degradation efficiency, broad active light wavelength, and good stability, the CeO₂/TiO₂ nanobelt heterostructures represent a new effective photocatalyst that is low‐cost, recyclable, and will have wide application in photodegradation of various organic pollutants. The new capture–photodegradation–release mechanism for improved photocatalysis properties is of importance in the rational design and synthesis of new photocatalysts.     

Mesoporous TiO2 thin films embedded with Au nanoparticles for the enhancement of the photocatalytic properties

Mesoporous TiO₂ thin films were prepared by hydrothermal-oxidation of titanium metal thin films, which were obtained by DC magnetron sputtering technique. Gold nanoparticles, which were prepared by reduction of HAuCl₄, were embedded into the holes of the mesoporous TiO₂ films by capillary method followed by annealing in air up to 400 °C. The size of pore of TiO₂ films is about 100 nm and that of Au nanoparticles is about 10 nm in average. The morphology of the films was analyzed by field emission scanning electron microscope (FE-SEM) and scanning probe microscopes (SPMs). Subsequently, the photocatalytic performances of the obtained nanosystems in the decomposition of methylene blue solution are discussed. The obtained results show that the dispersion of Au nanoparticles on the mesoporous TiO2 matrix will help enhancing the photocatalytic activity with respect to pure TiO₂ under visible light irradiation.     

Influence of metal plasma ion implantation on photo-sensitivity of anatase TiO2 thin films

Nano-scale TiO₂ thin films were synthesized by using sol-gel and spin-coating techniques on glass substrates for photo-catalytic applications. The Ti(IV) butoxide-based TiO₂ thin films were optimized for transforming into the high-purity crystalline anatase phase when calcined at 500 °C. To further enhance the photo-catalysis sensitivity of TiO₂ thin films for use in visible light environments, a metal plasma ion implantation process was implemented to modify the band gap electron configuration of Ti. Various transition metal atoms such as Ni, Cu, V, and Fe were ionized and accelerated at 20 keV to impinge on the surface of TiO₂ substrates at a dosage of 5 × 10¹⁵ ions/cm². ESCA analysis confirmed the binding energy shift of Ti by 0.8-1.2 eV, which accounted for the increased effective positive charge of Ti, resulting in more effective electron trapping capability and, thus, the electron-hole pair separation. In addition, the absorption spectroscopy demonstrated that optical absorption in the visible light regime occurred in specimens implanted with transition metal ions, likely due to the formation of extra impurity energy levels within the original TiO₂ band gap energy structure. Among all tested implant materials, the band gap energy of TiO₂ was effectively reduced by Cu and Fe ion implantation by 0.9-1.0 eV, which was sufficient enough to excite valence electrons over the band gap in visible light environments. The feasibility of the metal-doped TiO₂ thin films for effective applications under visible light irradiation was further confirmed by using super-hydrophilicity contact-angle measurement.     

Fabrication and photocatalytic property of ZnO nanorod arrays on Cu2O thin film

ZnO nanorod arrays were fabricated on Cu₂O thin film by a simple low-temperature liquid-phase-deposition method. The samples were characterized by X-ray powder diffraction (XRD) and field emission scanning electron microscopy (FESEM). The UV-Vis spectroscopy showed that the obtained sample was able to absorb a large part of visible light (up to 650 nm). Their photocatalytic activities were investigated by degradation of dye methylene blue (MB) under UV-Vis and visible light irradiation. It was found that the photocatalytic activity of the ZnO/Cu₂O NRs was higher than the ZnO/ZnO NRs under UV-Vis light. In a word, Cu₂O played an important role in enhancing the photocatalytic activity of the ZnO/Cu₂O NRs.