Effect of silane‐grafted polypropylene on the mechanical properties and crystallization behavior of talc/polypropylene composites

Talc‐filled polypropylene (PP) composites coupled with silane‐grafted polypropylene (PP‐g‐Si) were prepared. Effect of PP‐g‐Si on the mechanical properties, crystallization, and melting behavior of PP composites was investigated. Compared with the uncoupled composites, the mechanical properties of Talc/PP composites coupled with a small amount of PP‐g‐Si were increased to some extent. Meanwhile, PP‐g‐Si can promote crystallization rate and increase crystallization temperature of PP in the composites. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 77: 2974–2977, 2000     

Hydrophilicity and crystallization behavior of PVDF/PMMA/TiO<Subscript>2</Subscript>(SiO<Subscript>2</Subscript>) composites prepared by in situ polymerization

Composites with enhanced hydrophilicity were prepared by adding TiO₂ or SiO₂ nanoparticles during the in situ polymerization of methyl methacrylate (MMA) in poly(vinylidene fluoride) (PVDF). The hydrophilicities of the PVDF/PMMA/TiO₂(SiO₂) composites generated in this manner were characterized by contact angle measurements and atomic force microscopy (AFM). The hydrophilicity was dependent on nanoparticle content; it gradually increased with increasing TiO₂ (or SiO₂) content when the TiO₂ (or SiO₂) content was no more than 4 wt% of PVDF. A homogeneous dispersion of the TiO₂ (or SiO₂) nanoparticles in the composite matrix was observed in scanning electron microscope (SEM) images. Based on Fourier transform infrared (FTIR) spectra and wide angle X-ray diffraction (WAXD) analyses, the crystalline phase composition of PVDF was not influenced by the addition of TiO₂ (or SiO₂); PVDF crystallized predominantly in the α phase after in situ polymerization. Nevertheless, the nanoparticles can promote the formation of the β phase of PVDF in composites; the β-phase content increased with increasing TiO₂ content, while it was almost independent of SiO₂ content.     

Some characteristics of heat-resisting concretes modified by SiO<Subscript>2</Subscript> and TiO<Subscript>2</Subscript> nanoparticles

Nanoparticles of SiO₂ or TiO₂ have been added in the preparation of heat-resisting concretes of two types. The major technical and chemical characteristics have been determined. Features have been found in some of the technological operations in making the concretes of both types, and also aspects of the physicomechanical properties. Higher chemical stability has been found for heat-resisting concrete containing TiO₂ nanoparticles in an NaOH solution.     

Preparation and dielectric properties of SiO<Subscript>2</Subscript>/silicate-1 ceramics

For exploring the using of silicate-1 zeolite in dielectric ceramic, SiO₂@silicate-1 ceramics were fabricated by combining oxidation-bonding, sol–gel directional infiltration and sintering methods. The resulting samples were analyzed by X-ray diffraction, scanning electron microscope, energy dispersive spectrometer, digital hardness tester and microwave dielectric measurement system. It can be found that silicate-1 particles are well bond by silica sol. And the pores of perform are partially filled with silica. The sintering temperature has great effect on microstructure and properties of SiO₂@silicate-1 ceramics. When the ceramic is sintered at 400 and 600 °C, it keeps the MFI-type structure and almost has the same low-dielectric-constant (5.71 and 5.62, respectively). When the ceramic is sintered at 800 and 1000 °C, its MFI-type structure is broken down and its dielectric constant is 7.38 and 6.75, respectively.     

Microstructure,mechanical properties,and high-temperature oxidation resistance of AlN/SiO<Subscript>2</Subscript> nanomultilayer coatings

The microstructure, mechanical properties, and high-temperature oxidation resistance of AlN/SiO₂ nanomultilayer coatings with various SiO₂ layer thicknesses were investigated using X-ray diffractometry, high-resolution transmission electron microscopy, scanning electron microscopy, and nanoindentation. The results revealed that SiO₂ formed wurtzite-typed hexagonal pseudo-crystal structures and grew epitaxially with AlN when its thickness was less than 0.6 nm. Meanwhile, the multilayer coatings yielded superhardness effect with a maximum hardness of 29.0 GPa. A minute increase in SiO₂ thickness from 0.6 to 0.9 nm would decrease the hardness of the nanomultilayer coatings due to the formation of amorphous SiO₂ and destruction of epitaxial structure. The high hardness of superhard coatings was sustained after high-temperature annealing treatment of up to 800°C. However, a further increase in annealing temperature to 900°C caused severe oxidation of AlN and thus degradation of coating’s hardness.     

Interfacial influence on mechanical properties of polypropylene/polypropylene‐grafted silica nanocomposites

Three types of polypropylene‐grafted silica (PGS‐2 K, PGS‐8 K and PGS‐30 K) with different grafting chain lengths were prepared. After melt‐blending PGS with polypropylene (PP), we studied the PP/PGS interface properties and the influence of PP/PGS interfaces on mechanical properties of nanocomposites. The strong matrix/particle interface was observed in PP/PGS‐30 K nanocomposites with 5 wt % particle loading as evidenced by 2.5 °C increased glass transition temperature (T_g) compared with neat PP, whereas the weak matrix/particle interface was observed in PP/PGS‐2 K nanocomposites with decreased T_g. The variations in the matrix/particle interfacial strength lead to a transition in the yield stress of nanocomposites. Compared with the unfilled PP, the yield stress of the PP/PGS‐2 K nanocomposites is decreased by 0.7 MPa, and the yield stress of the PP/PGS‐30 K nanocomposites is enhanced by 1.4 MPa. In addition, benefiting from good dispersion, the PP/PGS‐masterbatch nanocomposites with a strong matrix/particle interface not only exhibit increased Young's modulus and yield stress, but also the strain at break remains in line with the unfilled PP, which is in contrast to the conventional wisdom that the gain in modulus and strength must be at the expense of the decreased break strain. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 45887.     

Effects of nanoparticle treatment on the crystallization behavior and mechanical properties of polypropylene/calcium carbonate nanocomposites

Effects of nanoparticle surface treatment on the crystallization behavior and mechanical properties of polypropylene (PP)/CaCO₃ nanocomposites were investigated by using differential scanning calorimetry (DSC), polarized optical microscope (POM), X‐ray diffraction (XRD), transmission electron microscopy (TEM), and scanning electron microscopy (SEM). The results demonstrated that the interfacial interaction formed between PP and nanoparticles significantly influenced the thermal and mechanical properties of nanocomposites. It was found that CaCO₃ nanoparticles modified by a single aluminate coupling agent (CA‐1) could improve the onset crystallization temperature more effectively than that modified by a compound surface‐treating agent (CA‐2) could. However, there is no significant difference in total rate of crystallization for the two PP/CaCO₃ nanocomposites (PPC‐1 and PPC‐2), which contained CA‐1 and CA‐2, respectively. In contrast, CA‐2 modified nanoparticles could cause smaller spherulites and induce much more β‐phase crystal in nanocomposites than that of CA‐1 modified nanoparticles. This may be explained by a synergistic effect of aluminate coupling agent and stearic acid in CA‐2, which also resulted in an improved toughness for PPC‐2. © 2006 Wiley Periodicals, Inc. J Appl PolymSci 102: 3480–3488, 2006     

Polymethacrylic acid/Na-montmorillonite/SiO<Subscript>2</Subscript> nanoparticle composites structures and thermal properties

In this article, polymethacrylic acid/Na-montmorillonite/SiO₂ nanoparticle (PMAA/Na-MMT/SiO₂) composites were prepared via in situ polymerization. Fourier transform infrared spectroscopy (FTIR) indicated that the polymerization of SiO₂ nanoparticle and MAA have been taken place. X-ray diffraction (XRD) results suggest that Na-MMT layers are exfoliated during the polymerization process. As evidenced by the transmission electron microscopy (TEM), the Na-MMT layers and SiO₂ nanoparticles exhibit good dispersion in the polymer matrix. It was found that the PMAA/Na-MMT/SiO₂ composite exhibit considerably enhanced thermal properties compared with the PMAA/Na-MMT.     

Dehydrogenation of isobutane over Sn/Pt/Na-ZSM-5 catalysts: The effect of SiO<Subscript>2</Subscript>/Al<Subscript>2</Subscript>O<Subscript>3</Subscript> ratio,amount and distribution of Pt nanoparticles on the catalytic behavior

Sn/Pt/Na-ZSM-5 was used as catalyst for the dehydrogenation of isobutane, and the effect of SiO₂/Al₂O₃ ratio and the dispersion of Pt nanoparticles on the conversion and product selectivity were studied under atmospheric pressure at 848 K. The catalysts were characterized by various techniques such as H₂ chemisorption, TEM, SEM, EDX, XRD, FT-IR, TG/DTG, elemental analysis by XRF and ICP techniques. Higher dispersion of Pt nanoparticles in the catalyst with SiO₂/Al₂O₃ ratio of 40 resulted in higher selectivity for isobutene.     

Polydimethylsiloxane assisted supercritical CO<Subscript>2</Subscript> foaming behavior of high melt strength polypropylene grafted with styrene

Foamable high melt strength polypropylene (HMSPP) was prepared by grafting styrene (St) onto polypropylene (PP) and simultaneously introducing polydimethylsiloxane (PDMS) through a one-step melt extrusion process. The effect of PDMS viscosity on the foaming behavior of HMSPP was systematically investigated using supercritical CO₂ as the foaming agent. The results show that the addition of PDMS has little effect on the grafting reaction of St and HMSPP exhibits enhanced elastic response and obvious strain hardening effect. Though the CO₂ solubility of HMSPP with PDMS (PDMS-HMSPP) is lower than that of HMSPP without PDMS, especially for PDMS with low viscosity, the PDMS-HMSPP foams exhibit narrow cell size distribution and high cell density. The fracture morphology of PDMS-HMSPP shows that PDMS with low viscosity disperses more easily and uniformly in HMSPP matrix, leading to form small domains during the extrusion process. These small domains act as bubble nucleation sites and thus may be responsible for the improved foaming performance of HMSPP.

Open image in new window

     

Preparation of hydrophobic SiO<Subscript>2</Subscript>@(TiO<Subscript>2</Subscript>/MoS<Subscript>2</Subscript>) composite film and its self-cleaning properties

TiO₂/MoS₂ composite was encapsulated by hydrophobic SiO₂ nanoparticles using a sol–gel hydrothermal method with methyltriethoxysilane (MTES), titanium tetrachloride (TiCl₄), and molybdenum disulfide (MoS₂) as raw materials. Then, a novel dual functional composite film with hydrophobicity and photocatalytic activity was fabricated on a glass substrates via the combination of polydimethylsiloxane adhesives and hydrophobic SiO₂@(TiO₂/MoS₂) composite particles. The influence of the mole ratios of MTES to TiO₂/MoS₂ (M:T) on the wettability and photocatalytic activity of the composite film was discussed. The surface morphology, chemical compositions, and hydrophobicity of the composite film on the glass substrate were investigated by scanning electron microscopy, transmission electron microscopy, X-ray powder diffraction, Fourier transform infrared spectroscopy, X-ray photoelectron spectroscopy, and water contact angle (water CA) measurements. The results indicated that the composite film exhibited stable superhydrophobicity and excellent photocatalytic activity for degradation of methyl orange (MO) even after five continuous cycles of photocatalytic reaction when M/T was 7:1. The water CA and degradation efficiency for MO remained at 154° and 94%, respectively. Further, the composite film showed a good non-sticking characteristic with the water sliding angle (SA) at about 4°. The SiO₂@(TiO₂/MoS₂) composite consisting of hydrophobic SiO₂ nanoparticles and TiO₂/MoS₂ heterostructure could provide synergistic effects for maintaining long-term self-cleaning performance.     

CO and CO<Subscript>2</Subscript> Methanation Over Ni/SiC and Ni/SiO<Subscript>2</Subscript> Catalysts

Ni/SiC and Ni/SiO₂ catalysts prepared by both wet impregnation (WI) and deposition–precipitation (DP) methods were compared for CO and CO₂ methanation. The prepared catalysts were characterized using N₂ physisorption, temperature-programmed reduction with H₂ (H₂-TPR), H₂ chemisorption, pulsed CO₂ chemisorption, temperature-programmed desorption of CO₂ (CO₂-TPD), transmission electron microscopy, and X-ray diffraction. H₂-TPR analysis revealed that the catalysts prepared by DP exhibit stronger interaction between the nickel oxides and support than those prepared by WI. The former catalysts exhibit higher Ni dispersions than the latter. The catalytic activities for both reactions over Ni/SiC and Ni/SiO₂ catalysts prepared by WI increase on increasing the Ni content from 10 to 20 wt%. The Ni/SiC catalyst prepared by DP shows higher catalytic activity for CO and CO₂ methanation than that of the Ni/SiC catalyst prepared by WI. Furthermore, it exhibits the highest catalytic activity for CO methanation among the tested catalysts. The high Ni dispersion achieved by the DP method and the high thermal conductivity enabled by SiC are beneficial for both CO and CO₂ methanation.     

Li<Subscript>2</Subscript>Cu<Subscript>2</Subscript>(MoO<Subscript>4</Subscript>)<Subscript>3</Subscript>/TiO<Subscript>2</Subscript> + SiO<Subscript>2</Subscript>/Ti compositions for the catalytic afterburning of diesel soot

Two methods were used to obtain a catalytically active oxide coating on the surface of titanium for the catalytic afterburning of diesel soot: plasma electrochemical formation of an oxide film on the surface of titanium and extraction pyrolytic deposition of the Li₂Cu₂(MoO₄)₃ compound. The Li₂Cu₂(MoO₄)₃/TiO₂ + SiO₂/Ti compositions synthesized by the single-step extraction pyrolytic treatment of the oxidized surface of titanium ensured a high burning rate of soot of ∼300°C. The subsequent deposition of Li₂Cu₂(MoO₄)₃ lowers the activity of the catalyst, due probably to the growth of molybdate phase crystallites and the filling of open oxide film pores. Double lithium-copper molybdate is able to reduce appreciably the concentration of CO in the oxidation products of soot. The advantages of these methods are the possibility of forming high-cohesion durable coatings on surfaces of any complexity, the simplicity of their implementation, and high productivity and low cost. The obtained results can be recommended for use in developing methods for creating composite coatings on catalytic soot filters.     

Optical Properties of CeO<Subscript>2</Subscript> Doped SiO<Subscript>2</Subscript>-Na<Subscript>2</Subscript>O-CaO-P<Subscript>2</Subscript>O<Subscript>5</Subscript> Glasses

Cerium oxide is one of the most important rare earth elements that is introduced into glass compositions due to its great effects on the optical properties. CeO₂ was introduced in Hench’s patented SiO₂-Na₂O-CaO-P₂O₅ glasses with different concentrations in order to study its effect on the optical behavior of this glass including optical band gap, transmittance, reflectance and refractive index and to give a complete view for the optical properties on cerium oxide-doped silicate glasses.     

Dependence of the optical properties of the 30.5K<Subscript>2</Subscript>O · 8.3Al<Subscript>2</Subscript>O<Subscript>3</Subscript> · 3.6SiO<Subscript>2</Subscript> · 57.6P<Subscript>2</Subscript>O<Subscript>5</Subscript> glass on the trivalent titanium content

An optical material, namely, the potassium aluminosilicophosphate glass activated with trivalent titanium ions, is synthesized and studied. The optimum concentration range (0.2–10.0 wt % Ti₂O₃) that provides the best physical, luminescent, and kinetic properties of glasses is determined. This makes it possible to use the sensitizing properties of Ti³⁺ ions to the greatest extent.Original Russian Text Copyright © 2004 by Fizika i Khimiya Stekla, Batyaev, Leonov.     

Melt-spinning and thermal stability behavior of TiO<Subscript>2</Subscript> nanoparticle/polypropylene nanocomposite fibers

The elongational flow properties of TiO₂ nanoparticle/polypropylene (PP) nanocomposite fibers were studied via melt spinning. The diameter, tension, and flow rate of fibers were directly measured and used to calculate the apparent elongational viscosity and apparent elongational strain rate using Cogswell’s theory. Thermal gravimetric analysis (TGA) was used to demonstrate that the TiO₂ nanoparticles improved the thermal stability of the PP fibers. With a 1–3 wt % loading of the TiO₂ nanoparticles, the PP fiber decomposition temperatures ranged from 338 °C for the pristine polymer to 342, 349, and 367 °C; the decomposition was accompamied by an initial 95 wt % weight loss. In addition, the well-distributed morphology of the TiO₂ nanoparticles on the side surface of the PP matrix was observed using atomic force microscopy (AFM). At 1 wt % loading of the TiO₂ nanoparticles, the surfaces of the PP nanofibers contained mono-disperse nanoparticles with sizes of 20–50 nm. Furthermore, the TiO₂ nanoparticle/PP nanocomposite fibers were shown to be thermally stable and are suitable for application as an antibacterial polymer.     

Kinetics of crystal nucleation of Na<Subscript>2</Subscript>O · 2CaO · 3SiO<Subscript>2</Subscript>-based solid solutions in glasses of the Na<Subscript>2</Subscript>SiO<Subscript>3</Subscript>—CaSiO<Subscript>3</Subscript> pseudobinary join

The kinetics of crystal nucleation is investigated in sodium calcium silicate glasses of two compositions (22.4 and 24.4 mol % Na₂O), which belong to the Na₂SiO₃—CaSiO₃ pseudobinary join and, according to the phase diagram, lie in the region of the formation of solid solutions between the compositions Na₂O · 2CaO · 3SiO₂ and Na₂O · CaO · 2SiO₂. The stationary rate of crystal nucleation of Na₂O · 2CaO · 3SiO₂-based solid solutions is measured as a function of temperature. It is shown that the maximum stationary rate of nucleation increases with an increase in the sodium oxide content in the initial glasses. The experimental data are analyzed in the framework of the classical nucleation theory.Original Russian Text Copyright © 2004 by Fizika i Khimiya Stekla, Soboleva, Yuritsyn, Ugolkov.