共查询到20条相似文献,搜索用时 15 毫秒
1.
Effect of additives, In 2O 3, SnO 2, CoO, CuO and Ag, on the catalytic performance of Ga 2O 3–Al 2O 3 prepared by sol–gel method for the selective reduction of NO with propene in the presence of oxygen was studied. As for the reaction in the absence of H 2O, CoO, CuO and Ag showed good additive effect. When H 2O was added to the reaction gas, the activity of CoO-, CuO- and Ag-doped Ga 2O 3–Al 2O 3 was depressed considerably, while an intensifying effect of H 2O was observed for In 2O 3- and SnO 2-doped Ga 2O 3–Al 2O 3. Of several metal oxide additives, In 2O 3-doped Ga 2O 3–Al 2O 3 showed the highest activity for NO reduction by propene in the presence of H 2O. Kinetic studies on NO reduction over In 2O 3–Ga 2O 3–Al 2O 3 revealed that the rate-determining step in the absence of H 2O is the reaction of NO 2 formed on Ga 2O 3–Al 2O 3 with C 3H 6-derived species, whereas that in the presence of H 2O is the formation of C 3H 6-derived species. We presumed the reason for the promotional effect of H 2O as follows: the rate for the formation of C 3H 6-derived species in the presence of H 2O is sufficiently fast compared with that for the reaction of NO 2 with C 3H 6-derived species in the absence of H 2O. Although the retarding effect of SO 2 on the activity was observed for all of the catalysts, SnO 2–Ga 2O 3–Al 2O 3 showed still relatively high activity in the lower temperature region. 相似文献
2.
Catalytic properties of supported gallium oxides have been examined for the selective reduction of NO by CH 4 in excess oxygen. The activity was greatly affected by the support; Ga 2O 3/Al 2O 3 (Al 2O 3 supported Ga 2O 3) and Ga 2O 3–Al 2O 3 mixed oxide exhibited high activity and selectivity as comparable to Ga-ZSM-5, while unsupported Ga 2O 3 and the other supported Ga 2O 3 were ineffective. For Ga 2O 3/Al 2O 3, the activity changed with Ga 2O 3 content, and was highest at about 30 wt% Ga 2O 3, which corresponds to a theoretical monolayer coverage. Gallium oxide highly dispersed on Al 2O 3 is considered to be responsible for the high activity and selectivity. The reaction characteristics of Ga 2O 3/Al 2O 3 were studied and compared with Ga-ZSM-5 and Co-ZSM-5. Ga 2O 3/Al 2O 3 exhibited the highest activity and selectivity at high temperature. In addition, Ga 2O 3/Al 2O 3 showed higher tolerance against water than Ga-ZSM-5. C 3H 8 and C 3H 6 were also evaluated as reducing agents, and Ga 2O 3/Al 2O 3 showed higher activity than Ga-ZSM-5 above 723 K achieving almost complete reduction of NO to N 2. 相似文献
3.
以Al_2O_3为载体,RuCl_3·xH_2O和FeCl_3·6H_2O为活性组分前驱体,采用吸附-沉淀法制备了Ru-Fe/Al_2O_3和Ru/Al_2O_3催化剂,以马来酸二甲酯加氢合成丁二酸二甲酯为探针反应,结合H_2-TPR和XRD表征技术,考察Fe改性Ru基催化剂的氧化-还原性能及催化活性。经氧化-还原循环处理后,催化剂Ru-Fe/Al_2O_3上马来酸二甲酯加氢活性高于Ru/Al_2O_3。XRD结果显示,经处理的Ru-Fe/Al_2O_3上未见金属Ru的特征衍射峰,而Ru/Al_2O_3上出现了金属Ru的特征衍射峰。结合H_2-TPR结果推断,Ru与Fe之间发生了相互作用,这种协同作用可以改善Ru/Al_2O_3催化剂的热稳定性。 相似文献
4.
Ag-based catalysts supported on various metal oxides, Al 2O 3, TiO 2, and TiO 2–Al 2O 3, were prepared by the sol–gel method. The effect of SO 2 on catalytic activity was investigated for NO reduction with propene under lean burn condition. The results showed the catalytic activities were greatly enhanced on Ag/TiO 2–Al 2O 3 in comparison to Ag/Al 2O 3 and Ag/TiO 2, especially in the low temperature region. Application of different characterization techniques revealed that the activity enhancement was correlated with the properties of the support material. Silver was highly dispersed over the amorphous system of TiO 2–Al 2O 3. NO 3− rather than NO 2− or NO x reacted with the carboxylate species to form CN or NCO. NO 2 was the predominant desorption species in the temperature programmed desorption (TPD) of NO on Ag/TiO 2–Al 2O 3. More amount of formate (HCOO −) and CN were generated on the Ag/TiO 2–Al 2O 3 catalyst than the Ag/Al 2O 3 catalyst, due to an increased number of Lewis acid sites. Sulfate species, resulted from SO 2 oxidation, played dual roles on catalytic activity. On aged samples, the slow decomposition of accumulated sulfate species on catalyst surface led to poor NO conversion due to the blockage of these species on active sites. On the other hand, catalytic activity was greatly enhanced in the low temperature region because of the enhanced intensity of Lewis acid site caused by the adsorbed sulfate species. The rate of sulfate accumulation on the Ag/TiO 2–Al 2O 3 system was relatively slow. As a consequence, the system showed superior capability for selective adsorption of NO and SO 2 toleration to the Ag/Al 2O 3 catalyst. 相似文献
5.
Catalytic performance of Sn/Al 2O 3 catalysts prepared by impregnation (IM) and sol–gel (SG) method for selective catalytic reduction of NO x by propene under lean burn condition were investigated. The physical properties of catalyst were characterized by BET, XRD, XPS and TPD. The results showed that NO 2 had higher reactivity than NO to nitrogen, the maximum NO conversion was 82% on the 5% Sn/Al 2O 3 (SG) catalyst, and the maximum NO 2 conversion reached nearly 100% around 425 °C. Such a temperature of maximum NO conversion was in accordance with those of NO x desorption accompanied with O 2 around 450 °C. The activity of NO reduction was enhanced remarkably by the presence of H 2O and SO 2 at low temperature, and the temperature window was also broadened in the presence of H 2O and SO 2, however the NO x desorption and NO conversion decreased sharply on the 300 ppm SO 2 treated catalyst, the catalytic activity was inhibited by the presence of SO 2 due to formation of sulfate species (SO 42−) on the catalysts. The presence of oxygen played an essential role in NO reduction, and the activity of the 5% Sn/Al 2O 3 (SG) was not decreased in the presence of large oxygen. 相似文献
6.
A systematic mechanistic study of NO storage and reduction over Pt/Al 2O 3 and Pt/BaO/Al 2O 3 is carried out using Temporal Analysis of Products (TAP). NO pulse and NO/H 2 pump-probe experiments at 350 °C on pre-reduced, pre-oxidized, and pre-nitrated catalysts reveal the complex interplay between storage and reduction chemistries and the importance of the Pt/Ba coupling. NO pulsing experiments on both catalysts show that NO decomposes to major product N 2 on clean Pt but the rate declines as oxygen accumulates on the Pt. The storage of NO over Pt/BaO/Al 2O 3 is an order of magnitude higher than on Pt/Al 2O 3 showing participation of Ba in the storage even in the absence of gas phase O 2. Either oxygen spillover or transient NO oxidation to NO 2 is postulated as the first steps for NO storage on Pt/BaO/Al 2O 3. The storage on Pt/Ba/Al 2O 3 commences as soon as Pt–O species are formed. Post-storage H 2 reduction provides evidence that a fraction of NO is not stored in close proximity to Pt and is more difficult to reduce. A closely coupled Pt/Ba interfacial process is corroborated by NO/H 2 pump-probe experiments. NO conversion to N 2 by decomposition is sustained on clean Pt using excess H 2 pump-probe feeds. With excess NO pump-probe feeds NO is converted to N 2 and N 2O via the sequence of barium nitrate and NO decomposition. Pump-probe experiments with pre-oxidized or pre-nitrated catalyst show that N 2 production occurs by the decomposition of NO supplied in a NO pulse or from the decomposition of NOx stored on the Ba. The transient evolution of the two pathways depends on the extent of pre-nitration and the NO/H 2 feed ratio. 相似文献
7.
The role of La 2O 3 loading in Pd/Al 2O 3-La 2O 3 prepared by sol–gel on the catalytic properties in the NO reduction with H 2 was studied. The catalysts were characterized by N 2 physisorption, temperature-programmed reduction, differential thermal analysis, temperature-programmed oxidation and temperature-programmed desorption of NO. The physicochemical properties of Pd catalysts as well as the catalytic activity and selectivity are modified by La2O3 inclusion. The selectivity depends on the NO/H2 molar ratio (GHSV = 72,000 h−1) and the extent of interaction between Pd and La2O3. At NO/H2 = 0.5, the catalysts show high N2 selectivity (60–75%) at temperatures lower than 250 °C. For NO/H2 = 1, the N2 selectivity is almost 100% mainly for high temperatures, and even in the presence of 10% H2O vapor. The high N2 selectivity indicates a high capability of the catalysts to dissociate NO upon adsorption. This property is attributed to the creation of new adsorption sites through the formation of a surface PdOx phase interacting with La2O3. The formation of this phase is favored by the spreading of PdO promoted by La2O3. DTA shows that the phase transformation takes place at temperatures of 280–350 °C, while TPO indicates that this phase transformation is related to the oxidation process of PdO: in the case of Pd/Al2O3 the O2 uptake is consistent with the oxidation of PdO to PdO2, and when La2O3 is present the O2 uptake exceeds that amount (1.5 times). La2O3 in Pd catalysts promotes also the oxidation of Pd and dissociative adsorption of NO mainly at low temperatures (<250 °C) favoring the formation of N2. 相似文献
8.
A multi-component NO x-trap catalyst consisting of Pt and K supported on γ-Al 2O 3 was studied at 250 °C to determine the roles of the individual catalyst components, to identify the adsorbing species during the lean capture cycle, and to assess the effects of H 2O and CO 2 on NO x storage. The Al 2O 3 support was shown to have NO x trapping capability with and without Pt present (at 250 °C Pt/Al 2O 3 adsorbs 2.3 μmols NO x/m 2). NO x is primarily trapped on Al 2O 3 in the form of nitrates with monodentate, chelating and bridged forms apparent in Diffuse Reflectance mid-Infrared Fourier Transform Spectroscopy (DRIFTS) analysis. The addition of K to the catalyst increases the adsorption capacity to 6.2 μmols NO x/m 2, and the primary storage form on K is a free nitrate ion. Quantitative DRIFTS analysis shows that 12% of the nitrates on a Pt/K/Al 2O 3 catalyst are coordinated on the Al 2O 3 support at saturation. When 5% CO2 was included in a feed stream with 300 ppm NO and 12% O2, the amount of K-based nitrate storage decreased by 45% after 1 h on stream due to the competition of adsorbed free nitrates with carboxylates for adsorption sites. When 5% H2O was included in a feed stream with 300 ppm NO and 12% O2, the amount of K-based nitrate storage decreased by only 16% after 1 h, but the Al2O3-based nitrates decreased by 92%. Interestingly, with both 5% CO2 and 5% H2O in the feed, the total storage only decreased by 11%, as the hydroxyl groups generated on Al2O3 destabilized the K–CO2 bond; specifically, H2O mitigates the NOx storage capacity losses associated with carboxylate competition. 相似文献
9.
In situ growth of needlelike LaAl 11O 18 grains reinforcing Al 2O 3 composites can be fabricated by a coprecipitation method using La(NO 3) 3√6H 2O and Al(NO 3) 3√9H 2O as starting materials. The new two-step process involved firstly preparing needlelike LaAl 11O 18 grains distributed homogeneously in Al 2O 3 powder and then pressureless sintering the composite powders. The Al 2O 3/25 vol.%LaAl 11O 18 samples pressureless sintered at 1550°C for 4 h achieve relative density up to 96.5% and exhibit a bending strength of 420±30 MPa and a fracture toughness of 4.3±0.4 MPa m 1/2. 相似文献
10.
An In 2O 3/Al 2O 3 catalyst shows high activity for the selective catalytic reduction of NO with propene in the presence of oxygen. The presence of SO 2 in feed gas suppressed the catalytic activity dramatically at high temperatures; however it was enhanced in the low temperature range of 473–573 K. In TPD and FT-IR studies, the formation of sulfate species on the surface of the catalyst caused an inhibition of NO X adsorption sites, and the absorbance ability of NO was suppressed by the presence of SO 2, and the amount of ad-NO 3− species decreased obviously. This leads to a decrease of catalytic activity at higher temperatures. However, addition of SO 2 enhanced the formation of carboxylate and formate species, which can explain the promotional effect of SO 2 at low temperature, because active C 3H 6 (partially oxidized C 3H 6) is crucial at low temperature. 相似文献
11.
Experimental results describing the product distribution during the reduction of NO by H 2 on Pt/Al 2O 3 and Pt/BaO/Al 2O 3 catalysts are presented in the temperature range 30–500 °C and H 2/NO feed ratio range of 0.9–2.5. A microkinetic model that describes the kinetics of NO reduction by H 2 on Pt/Al 2O 3 is proposed and most of the kinetic parameters are estimated from either literature data or from thermodynamic constraints. The microkinetic model is combined with the short monolith flow model to simulate the conversions and selectivities corresponding to the experimental conditions. The predicted trends are in excellent qualitative and reasonable quantitative agreement with the experimental results. Both the model and the experiments show that N 2O formation is favored at low temperatures and low H 2/NO feed ratios, N 2 selectivity increases monotonically with temperature for H 2/NO feed ratios of 1.2 or less but goes through a maximum at intermediate temperatures (around 100 °C) for H 2/NO feed ratios 1.5 or higher. Ammonia formation is favored for H 2/NO feed ratios of 1.5 or higher and intermediate temperatures (100–350 °C) buts starts to decompose at a temperature of 400 °C or higher. The microkinetic model is used to determine the surface coverages and explain the trends in the experimentally observed selectivities. 相似文献
12.
A systematic reactivity study of N 2O, NO, and NO 2 on highly dispersed CuO phases over modified silica supports (SiO 2–Al 2O 3, SiO 2–TiO 2, and SiO 2–ZrO 2) has been performed. Different reaction paths for the nitrogen oxide species abatement were studied: from direct decomposition (N 2O) to selective reductions by hydrocarbons (N 2O, NO, and NO 2) and oxidation (NO to NO 2). The oxygen concentration, temperature, and contact time, were varied within suitable ranges in order to investigate the activity and in particular the selectivity in the different reactions studied. The support deeply influenced the catalytic properties of the active copper phase. The most acidic supports, SiO 2–Al 2O 3 and SiO 2–ZrO 2, led to a better activity and selectivity of CuO for the reactions of N 2O, NO, and NO 2 reductions and N 2O decomposition than SiO 2–TiO 2. The catalytic results are discussed in terms of actual turnover frequencies starting from the knowledge of the copper dispersion values. 相似文献
13.
Mixed oxides of alumina and zirconia having a relative composition of 50, 80 and 100% Zr 2O were synthesized by means of sol–gel methods. The catalysts were sulfated with H 2SO 4 1N, and were loaded with 0.3% Pt metal using the incipient wetness technique. The characterization of the physicochemical properties was carried out using XRD, N 2-adsorption at 78 K, and SEM. The catalytic properties of the Al 2O 3–ZrO 2 series were studied by means of dehydration of 2-propanol at 180°C and isomerization of n-hexane at 250°C, 1 atm. The sulfated solids presented a high surface acidity and a limited crystallinity, together with high activity for alcohol dehydration (i.e. 2-propanol). On the other hand, the Al 2O 3–ZrO 2 solid solutions (i.e. those having a 20–80% composition) turned out to be the most active ones for the isomerization of n-hexane. 相似文献
14.
The reduction of NO by propene in the presence of excess oxygen over mechanical mixtures of Au/Al 2O 3 with a bulk oxide has been investigated. The oxides studied were: Co 3O 4, Mn 2O 3, Cr 2O 3, CuO, Fe 2O 3, NiO, CeO 2, SnO 2, ZnO and V 2O 5. Under lean C 3H 6-SCR conditions, these oxides (with the exception of SnO 2) convert selectively NO to NO 2. When mechanically mixed with Au/Al 2O 3, the Mn 2O 3 and Co 3O 4 oxides and, to a much greater extent, CeO 2 act synergistically with this catalyst greatly enhancing its SCR performance. It was found that their synergistic action is not straightforwardly related to their activity for NO oxidation to NO 2. The exhibited catalytic synergy may be due to the operation of either remote control or a bifunctional mechanism. In the later case, the key intermediate must be a short-lived compound and not the NO 2 molecule in gas-phase. 相似文献
15.
Reticular oxygen of Al 2O 3 or CeO x supported on Al 2O 3 was used for the epoxidation of propene without any double bond cleavage. In batch reaction, Al 2O 3 alone was able to convert propene into propene oxide (PO) with 100% selectivity and 2% conversion of propene with a close to 3:1 ratio with respect to the number of Al(III) reduced to elemental Al. When Ce 2O 3/Al 2O 3 or CeO 2/Al 2O 3 was used, Al remained in its +3 oxidation state, while the Ce oxide was the oxidant as demonstrated by XPS analyses. CeO x/Al 2O 3 was more active (propene conversion yield of 4–5%) but the selectivity was lower (70%) as PO was isomerized into acetone and propionaldehyde. Interestingly the use of reticular oxygen very much improves the selectivity with respect to the use of pure O2. In fact, while propene was more efficiently oxidized (10%) with O2 in presence of Al2O3 or CeOx/Al2O3, the selectivity was as low as 40% because C1 and C2 products were formed. However, the use of reticular oxygen represents a selective two-step technique for the use of molecular oxygen as oxidant of propene. The used oxides can be re-oxidized and the whole process can be further improved towards higher yields. PO is quantitatively converted into propene carbonate by reaction with CO2 in presence of Nb2O5. 相似文献
16.
Nanosized particles dispersed uniformly on Al 2O 3 particles were prepared from the decomposition of precursor Cr(CO) 6 by metal organic chemical vapor deposition (MOCVD) in a fluidized chamber. These nanosized particles consisted of Cr 2O 3, CrC 1−x, and C. A solid solution of Al 2O 3–Cr 2O 3 and an Al 2O 3–Cr 2O 3/Cr 3C 2 nanocomposite were formed when these fluidized powders were pre-sintered at 1000 and 1150 °C before hot-pressing at 1400 °C, respectively. In addition, an Al 2O 3–Cr 2O 3/Cr-carbide (Cr 3C 2 and Cr 7C 3) nanocomposite was formed when the particles were directly hot pressed at 1400 °C. The interface between Cr 3C 2 and Al 2O 3 is non-coherent, while the interface between Cr 7C 3 and Al 2O 3 is semi-coherent. 相似文献
17.
Composite types of TiO 2–Al 2O 3 supports, which are γ-aluminas coated by titania, have been prepared by chemical vapor deposition (CVD), using TiCl 4 as a precursor. Then supported molybdenum catalysts have been prepared by an impregnation method. As supports, we employed γ-alumina, anatase types of titania, and composite types of TiO 2–Al 2O 3 with different loadings of TiO 2. We studied the conversion of Mo from oxidic to sulfidic state through sulfurization by X-ray photoelectron spectroscopy (XPS). The obtained spectra unambiguously revealed the higher reducibility from oxidic to sulfidic molybdenum species on the TiO 2 and TiO 2–Al 2O 3 supports compared to that on the Al 2O 3 support. Higher TiO 2 loadings of the TiO 2–Al 2O 3 composite support led to higher reducibility for molybdenum species. Furthermore, the catalytic behavior of supported molybdenum catalysts has been investigated for hydrodesulfurization (HDS) of dibenzothiophene (DBT) and methyl-substituted DBT derivatives. The conversion over the TiO 2–Al 2O 3 supported Mo catalysts, in particular for the 4,6-dimethyl-DBT, is much higher than that obtained over Al 2O 3 supported Mo catalyst. The ratio of the corresponding cyclohexylbenzene (CHB)/biphenyl (BP) derivatives is increased over the Mo/TiO 2–Al 2O 3. This indicates that the prehydrogenation of an aromatic ring plays an important role in the HDS of DBT derivatives over TiO 2–Al 2O 3 supported catalysts. 相似文献
18.
Oxidation of propene and propane to CO 2 and H 2O has been studied over Au/Al 2O 3 and two different Au/CuO/Al 2O 3 (4 wt.% Au and 7.4 wt.% Au) catalysts and compared with the catalytic behaviour of Au/Co 3O 4/Al 2O 3 (4.1 wt.% Au) and Pt/Al 2O 3 (4.8 wt.% Pt) catalysts. The various characterization techniques employed (XRD, HRTEM, TPR and DR-UV–vis) revealed the presence of metallic gold, along with a highly dispersed CuO (6 wt.% CuO), or more crystalline CuO phase (12 wt.% CuO). A higher CuO loading does not significantly influence the catalytic performance of the catalyst in propene oxidation, the gold loading appears to be more important. Moreover, it was found that 7.4Au/CuO/Al2O3 is almost as active as Pt/Al2O3, whereas Au/Co3O4/Al2O3 performs less than any of the CuO-containing gold-based catalysts. The light-off temperature for C3H8 oxidation is significantly higher than for C3H6. For this reaction the particle size effect appears to prevail over the effect of gold loading. The most active catalysts are 4Au/CuO/Al2O3 (gold particles less than 3 nm) and 4Au/Co3O4/Al2O3 (gold particles less than 5 nm). 相似文献
19.
The phase diagram of the Al 2O 3–ZrO 2–Nd 2O 3 system was constructed in the temperature range 1250–2800 °C. The liquidus surface of the phase diagram reflects the preferentially eutectic interaction in the system. Two new ternary and one new binary eutectics were found. The minimum melting temperature is 1675 °C and it corresponds to the ternary eutectic Nd 2O 3·11Al 2O 3 + F-ZrO 2 + NdAlO 3. The solidus surface projection and the schematic of the alloy crystallization path confirm the preferentially congruent character of phase interaction in the ternary system. The polythermal sections present the complete phase diagram of the Al 2O 3–ZrO 2–Nd 2O 3 system. No ternary compounds or regions of remarkable solid solution were found in the components or binaries in this ternary system. 相似文献
20.
The effectiveness of Ag/Al 2O 3 catalyst depends greatly on the alumina source used for preparation. A series of alumina-supported catalysts derived from AlOOH, Al 2O 3, and Al(OH) 3 was studied by means of X-ray diffraction (XRD), scanning electron microscopy (SEM), ultraviolet–visible (UV–vis) spectroscopy, diffuse reflectance infrared Fourier transform (DRIFT) spectroscopy, O 2, NO + O 2-temperature programmed desorption (TPD), H 2-temperature programmed reduction (TPR), thermal gravimetric analysis (TGA) and activity test, with a focus on the correlation between their redox properties and catalytic behavior towards C 3H 6-selective catalytic reduction (SCR) of NO reaction. The best SCR activity along with a moderated C 3H 6 conversion was achieved over Ag/Al 2O 3 (I) employing AlOOH source. The high density of Ag–O–Al species in Ag/Al 2O 3 (I) is deemed to be crucial for NO selective reduction into N 2. By contrast, a high C 3H 6 conversion simultaneously with a moderate N 2 yield was observed over Ag/Al 2O 3 (II) prepared from a γ-Al 2O 3 source. The larger particles of Ag mO ( m > 2) crystallites were believed to facilitate the propene oxidation therefore leading to a scarcity of reductant for SCR of NO. An amorphous Ag/Al 2O 3 (III) was obtained via employing a Al(OH) 3 source and 500 °C calcination exhibiting a poor SCR performance similar to that for Ag-free Al 2O 3 (I). A subsequent calcination of Ag/Al 2O 3 (III) at 800 °C led to the generation of Ag/Al 2O 3 (IV) catalyst yielding a significant enhancement in both N 2 yield and C 3H 6 conversion, which was attributed to the appearance of γ-phase structure and an increase in surface area. Further thermo treatment at 950 °C for the preparation of Ag/Al 2O 3 (V) accelerated the sintering of Ag clusters resulting in a severe unselective combustion, which competes with SCR of NO reaction. In view of the transient studies, the redox properties of the prepared catalysts were investigated showing an oxidation capability of Ag/Al 2O 3 (II and V) > Ag/Al 2O 3 (IV) > Ag/Al 2O 3 (I) > Ag/Al 2O 3 (III) and Al 2O 3 (I). The formation of nitrate species is an important step for the deNO x process, which can be promoted by increasing O 2 feed concentration as evidenced by NO + O 2-TPD study for Ag/Al 2O 3 (I), achieving a better catalytic performance. 相似文献
|