The development of superplastic ductilities and microstructural homogeneity in a magnesium ZK60 alloy processed by ECAP

An extruded ZK60 magnesium alloy was processed by equal-channel angular pressing (ECAP) and then tested in tension at elevated temperatures. The results show the alloy is superplastic at a testing temperature of 473 K with an optimum ductility of 1310% when using an initial strain rate of 2.0 × 10⁻⁴ s⁻¹. The results demonstrate that optimum superplasticity is achieved at intermediate strain rates and there are decreases in the elongations to failure at both faster and slower strain rates. Microhardness measurements were taken both on the cross-sectional plane and along the axial direction after processing by ECAP. These measurements show the alloy is essentially homogeneous in the as-pressed condition.     

Processing of a magnesium alloy by equal-channel angular pressing using a back-pressure

Experiments were conducted on the magnesium AZ31 alloy to evaluate the significance of conducting equal-channel angular pressing (ECAP) with a back-pressure. Following processing by ECAP, the values of the Vickers microhardness were recorded on the cross-sectional planes and microstructural observations were undertaken using transmission electron microscopy. The results show an increase in the hardness in the first pass with significant microstructural inhomogeneity and a transition towards a more homogeneous structure with subsequent passes. The grain size was measured as 0.9 μm after 8 passes. A comparison with published data on the same alloy processed by ECAP without a back-pressure suggests several advantages in incorporating a back-pressure into ECAP. These advantages include the ability to achieve greater grain refinement, a potential for pressing at lower temperatures and the development of a more rapid evolution towards a homogeneous microstructure.     

Exceptional superplasticity in an AZ61 magnesium alloy processed by extrusion and ECAP

Experiments were conducted on a commercial AZ61 alloy to evaluate the potential for achieving an ultrafine grain size and superplastic ductilities through the use of the EX-ECAP two-step processing procedure of extrusion plus equal-channel angular pressing. The results show that EX-ECAP gives excellent grain refinement with grain sizes of 0.6 and 1.3 μm after pressing at 473 and 523 K, respectively. The alloy processed by EX-ECAP exhibits exceptional superplastic properties including a maximum elongation of 1320% after pressing through four passes when testing at 473 K with an initial strain rate of 3.3 × 10⁻⁴ s⁻¹. This result compares with an elongation of 70% achieved in the extruded condition without ECAP under similar testing conditions.     

Microstructure and mechanical properties of Cu and Cu-Zn alloys produced by equal channel angular pressing

Ultrafine-grained (UFG) Cu and Cu-Zn alloy were prepared using equal-channel angular pressing (ECAP) to investigate the effects of stacking fault energy (SFE) on microstructure evolution and mechanical properties. Combining with the previous researches, the grain refinement process of ECAP is divided into three stages based on the variation of tensile strength and plasticity. According to the influences of defects on strength and ductility during plastic deformation, the three stages are discussed in detail by considering the dislocation density, grain and twin boundaries. Besides, the impact of SFE on the strength and ductility of the UFG Cu-Zn alloys are evaluated, indicating that these two mechanical properties can be improved simultaneously in the whole ECAP process either through slightly or widely adjusting the SFE. This significant effect of SFE reflects in two aspects, one is in the microstructure evolution during ECAP processing and the other is in the subsequent tensile plastic deformation, both of which can be achieved through regulating the dislocation motion via changing the SFE.     

铸态AZ81镁合金ECAP态组织与性能研究

采用自制的90°模具,经Bc路径在温度为300℃下研究对比了铸态及不同道次的等通道挤压(ECAP)态AZ81镁合金微观组织和力学性能.结果表明ECAP随着挤压道次的增加,AZ81镁合金显微组织和力学性能发生显著变化.当挤压到4道次,平均晶粒尺寸由原来铸态的145um细化为9.6um,拉伸断口韧窝明显增多;抗拉强度从180 MPa提高到306 MPa,延伸率和硬度分别达到15.8%和142HL.分析表明,AZ81镁合金在高温挤压过程中Mg17Al12相粒子被破碎,并部分溶入基体,$-Mg基体与%-Mg17Al12相互相阻碍其晶粒长大,获得细小晶粒组织.     

Superplasticity of Mg-Zn-Y alloy containing quasicrystal phase processed by equal channel angular pressing

Equal channel angular pressing (ECAP) has been conducted on as-cast Mg-4.3 wt.%Zn-0.7 wt.%Y Mg alloy containing quasicrystal phase at a temperature of 623 K. After 8 ECAP passes, the grain size of the as-cast alloy is decreased from ∼ 120 to ∼ 3.5 μm, and the coarse eutectic quasicrystal phases are broken and dispersed in the alloy. Tensile testing has been performed on the ECAPed Mg-Zn-Y alloy at temperatures of 523 K and 623 K with initial strain rates from 1.5 × 10^− 3 to 1.5 × 10^− 4 s^− 1. The ECAPed alloy exhibits a maximum elongation of about 600% when testing at 623 K using an initial strain rate of 1.5 × 10^− 4 s^− 1. Grain boundary sliding is considered to be the dominant deformation mechanism of the Mg-Zn-Y alloy in the temperature and strain-rate range investigated.     

Microstructure and mechanical properties of ODS Fe14Cr model alloy processed by equal channel angular pressing

Abstract

A nanograin sized model oxide dispersion strengthened (ODS) ferritic steel with nominal composition Fe–14Cr–0·3Y₂O₃ (wt-%) was produced by mechanical alloying and consolidated by hot isostatic pressing. The alloy was submitted to severe plastic deformation by equal channel angular pressing (ECAP). Microstructural and mechanical characterisation was performed before and after ECAP. It was found that ECAP decreases and homogenises grain size without altering the nanoparticle dispersion, in addition to enhancing ductility and shifting the strength drop at high temperatures.     

Al-Cu合金析出相在等径角挤压中的演变

为了研究Al-Cu合金中两种不同析出相(θ′和θ相)在ECAP变形过程中的变化.采用透射电镜(TEM)和硬度测试方法研究了析出相形貌变化以及对合金性能的影响.结果表明:在本实验中,θ′和θ相其破碎、回溶速度明显不同,两者的破碎方式也不同.θ′相先是与基体失去取向关系,随后从其内部产生位错使其破碎,而θ相是被外部基体位错所切割、破碎.θ′相与位错的相互作用方式类似于绕过机制,θ相与位错的作用方式类似于切割机制.两种状态样品的硬度在变形过程中的变化趋势相同,但在第1道次后θ相状态样品的硬度增加值高于θ′相状态.     

Superplastic behavior of a fine-grained ZK60 magnesium alloy processed by high-ratio differential speed rolling

Grain size of the ZK60 alloy was effectively reduced to 12 μm through high-ratio differential speed rolling (HRDSR) for a thickness reduction of 70% in a single pass. Due to the strengthening effects of grain boundaries and particles, the HRDSR processed ZK60 exhibited a high tensile strength of 340 MPa. Low temperature superplasticity was attained at 473–493 K at low strain rates (5 × 10⁻⁴ s⁻¹) and high strain rate superplasticity was attained at 523–553 K at high strain rates (10⁻² s⁻¹). The optimum superplastic temperature was found to be 553 K where a maximum tensile elongation of 1000% was obtained at 1 × 10⁻³ s⁻¹. The deformation behavior of the HRDSR processed ZK60 at elevated temperatures could be depicted by considering contribution of grain boundary sliding and slip creep to total plastic flow. Difference in superplastic deformation behavior between the HRDSR processed and equal channel angular press processed ZK60 alloys was examined and discussed.     

Microstructure and mechanical properties of Al-7075 alloy processed by equal channel angular pressing combined with aging treatment

In order to examine the combined effect of plastic deformation and aging process, the Al 7075 alloy was subjected to equal channel angular pressing (ECAP) deformation by route B_C in various ECAP and aging conditions: pre-ECAP aging, post-ECAP aging and dynamic aging during ECAP at 393 K and 423 K. Followed by ECAP and aging treatment, Vickers microhardness and tensile test were performed and microstructural observations were undertaken using transmission electron microscopy (TEM) and X-ray diffractometer (XRD). TEM investigation showed that ultrafine-grained (UFG) materials with grain size less than 500 nm could be obtained after three or four passes of ECAP. Precipitates characterization revealed that maximum mechanical properties are achieved when the microstructure mainly consists of fine dispersion of small η^′ precipitates and minor quantities of GP zones. Dynamic aged specimens at 393 K and 423 K represented maximum and minimum mechanical properties, respectively, due to formation of fine η^′ precipitates plus GP zones and η^′ plus η precipitates, respectively. Dynamic aging during ECAP at 393 K appeared preferable to other procedures for attaining maximum mechanical properties as well as saving time and energy.     

Properties of AA6061 Processed by Multi-Axial Compressions/Forging (MAC/F)

Multi-axial compressions/forgings (MAC/F) were conducted at room temperature to obtain severe plastic deformation (SPD) of AA6061 alloy. Microhardness measurements taken across the cross-section of each of the MAC/F processed samples indicated that the hardness distribution is nonuniform during initial compressions/forgings and becomes uniform with subsequent compressions. Microhardness and tensile testing showed that the hardness, yield strength, and elongation of the MAC/F processed material followed similar trends to that for AA6061 processed by equal channel angular pressing (ECAP). The MAC/F material exhibited high strain rate sensitivity and high percentage of elongation to failure in the temperature range of 300-350°C. This observation is in agreement with the high formability of SPD-processed AA6061 over the same temperature range.     

Nano grained AZ31 alloy achieved by equal channel angular rolling process

Equal channel angular rolling (ECAR) is a severe plastic deformation process which is carried out on large, thin sheets. The grain size could be significantly decreased by this process. The main purpose of this study is to investigate the possibility of grain refinement of AZ31 magnesium alloy sheet by this process to nanometer. The effect of the number of ECAR passes on texture evolution of AZ31 magnesium alloy was investigated. ECAR temperature was controlled to maximize the grain refinement efficiency along with preventing cracking. The initial microstructure of as-received AZ31 sheet showed an average grain size of about 21 μm. The amount of grain refinement increased with increasing the pass number. After 10 passes of the process, significant grain refinement occurred and the field emission scanning electron microscopic (FESEM) micrographs showed that the size of grains were decreased significantly to about 14-70 nm. These grains were formed at the grain boundaries and inside some of the previous larger micrometer grains. Observation of optical microstructures and X-ray diffraction patterns (XRD) showed the formation of twins after ECAR process. Micro-hardness of material was studied at room temperature. There was a continuous enhancement of hardness by increasing the pass number of ECAR process. At the 8th pass, hardness values increased by 53%. At final passes hardness reduced slightly, which was attributed to saturation of strain in high number of passes.     

等径角挤压过程中材料的流变行为研究

分析了等径角挤压过程中材料流变的原因和特征,认为每道次挤压材料内部发生的剪切变形量与时间的函数曲线呈近似正态分布,适当升高温度和增加背压能有效减小难变形区,降低通道与试样接触面之间的摩擦能减小材料内部的滞变区.通过实验证明,随着挤压道次的增加,材料内部的滞变区将减小,均匀化程度会逐步提高.     

The evolution of homogeneity on longitudinal sections during processing by ECAP

An Al-6061 alloy was processed by equal-channel angular pressing at room temperature for one, two, four and six passes and microhardness measurements were recorded along linear traverses on longitudinal planes in the centers of each billet. The results show the average microhardness increases significantly in the first pass although there is a region of lower hardness running in a band near the bottom surface of the billet. Additional but smaller increases in hardness occur in subsequent passes. The hardness values are distributed homogeneously throughout the longitudinal plane after ECAP through six passes although there remains a very narrow region of lower hardness within a distance of 0.5 mm adjacent to the bottom surface. When combined with earlier microhardness measurements taken on the Al-6061 alloy on the cross-sectional plane, the results confirm the potential for achieving excellent homogeneity after pressing through a total of six passes.     

Finite element analysis of rotary-die equal channel angular pressing

In this paper, the finite element method (FEM) was applied to analyze the plastic flow and strain hardening behavior of pure copper, subjected to rotary-die equal channel angular pressing (RD-ECAP) up to four passes. The die was rotated 90° counter clockwise between the passes in the simulation. The effective strain distribution and load–stroke curves were investigated. The load was increased with the number of rotary-die equal channel angular pressing passes. The results show that, plastic deformation becomes inhomogeneous with the number of passes due to an end effect, which was not found seriously in conventional equal channel angular pressing (ECAP). Especially, decreasing corner gap with increasing the number of passes was observed and explained by the strain hardening effect.     

Microstructure and mechanical properties of pure gold processed by equal channel angular pressing

The microstructure and mechanical properties of pure gold were examined after different number of equal channel angular pressing passes. The hardness and 0.2% proof stress from the compression tests were observed to increase only up to the fourth pass whereas the compressive strength at 40% strain kept increasing gradually with increasing the number of passes. Microstructure with low angle grain boundaries and shear bands were observed until the eighth pass and equiaxed grains with high angle grain boundaries were observed only after the twelfth pass.     

Effects of grain size on compressive behaviour in ultrafine grained pure Mg processed by equal channel angular pressing at room temperature

Ultrafine-grained pure magnesium with an average grain size of 0.8 μm was produced by refining coarse-grained (980 μm) ingot by multi-pass equal channel angular pressing (ECAP) at room temperature with the application of a back pressure. The compressive deformation behaviour at room temperature depended on grain size, with deformation twinning and associated work hardening observed in coarse-grained Mg, but absent in the ultrafine grained material as decreasing grain size raised the stress for twinning above that for dislocation slip. The ultrafine grained Mg showed good plasticity with prolonged constant stress after some initial strain hardening.     

Full density consolidation of pure aluminium powders by cold hydro-mechanical pressing

Gas atomized pure Al powders were successfully consolidated into full density at room temperature by newly developed cold hydro-mechanical pressing (CHMP). The effects of the configuration of pressures on the relative density and microstructure of consolidated specimens were investigated. The full density consolidation of metal powders at room temperature resulted from severe shear deformation of the particles which ruptured the surface oxide layers. Our works demonstrate that the novel CHMP provides an economical approach to consolidate particulate material into high quality bulk preforms for engineering applications.     

An experimental verification of the finite element modelling of equal channel angular pressing

Strain hardening of pure copper and friction between the sample and die channels is considered for finite element modelling. To validate the FEM results, the FEM calculated effective strain variations were compared with the hardness measurements. Simulated load–stroke curve and peak load calculations were also compared with the experimentally recorded load–stroke curve and peak load. Different stages of the load–stroke curve of the ECAP process was explained in detail. In over all, good conformity is observed between the FEM calculations and experimental results.     

Microstructure and mechanical properties of Mg–Zn–Ca alloy processed by equal channel angular pressing

An ultrafine-grained (UFG) Mg–5.12 wt.% Zn–0.32 wt.% Ca alloy with an average grain size of 0.7 μm was produced by subjecting the as-extruded alloy to equal channel angular pressing (ECAP) for 4 passes at 250 °C. The fine secondary phase restricted the dynamic recrystallized (DRXed) grain growth during the ECAP processing, resulting in a remarkable grain refinement. A new texture was formed in the ECAPed Mg alloy with the {0 0 0 2} plane inclined at an angle of 58° relative to the extrusion direction. The yield stress (YS) was decreased in the as-ECAPed alloy with finer grains, indicating that the texture softening effect was dominant over the strengthening from grain refinement. The ductility of the as-ECAPed alloy was increased to 18.2%. The grain refinement caused an obvious decrease in work hardening rate in the as-ECAPed alloy during tensile deformation at room temperature.