Strong up-conversion luminescence and electrical properties of SrBi<Subscript>4</Subscript>Ti<Subscript>4</Subscript>O<Subscript>15</Subscript> multifunctional ceramics by Er<Superscript>3+</Superscript> doping

Novel green-emitting piezoelectric ceramics of SrBi_4?x Er _x Ti₄O₁₅ (SBT-xEr) were prepared. Strong up-conversion with bright green (524 and 548 nm) and a relatively weak red (660 nm) emission bands were obtained under 980 nm excitation at room temperature, which is attributed to the intra 4f–4f electronic transition of (²H_11/2, ⁴S_3/2)–⁴I_15/2 and the transition from ⁴F_9/2 to ⁴I_15/2 of Er³⁺ ions, respectively. Simultaneously, Er³⁺ doping promotes the electrical properties. At 0.8 mol%Er, the optimal electric properties with high Curie temperature of T _c?~527?°C, large remanent polarization of 2P _r?~14.92 μC/cm² and piezoelectric constant of d ₃₃?~17 pC/N was achieved. As a multifunctional material, Er³⁺ doped SBT showed a great potential to be used in 3D-display, bio-imaging, solid state laser and optical temperature sensor.     

High-temperature heat capacity and vibrational spectra of Eu<Subscript>2</Subscript>Sn<Subscript>2</Subscript>O<Subscript>7</Subscript>

The Eu₂Sn₂O₇ compound has been prepared by solid-state reaction (by sequentially firing a stoichiometric mixture of Eu₂O₃ and SnO₂ in air at 1273 and 1473 K) and its heat capacity has been determined by differential scanning calorimetry in the temperature range 370–1000 K. The heat capacity data have been used to evaluate the thermodynamic properties of europium stannate: enthalpy increment H°(T)–H°(370 K), entropy change S°(T)–S°(370 K), and reduced Gibbs energy Ф°(T). Raman spectra of Eu₂Sn₂O₇ polycrystals with the pyrochlore structure have been measured in the range 200–1200 cm^–1.     

Tunable luminescence properties and energy transfer of single-phase Ca<Subscript>4</Subscript>(PO<Subscript>4</Subscript>)<Subscript>2</Subscript>O: Dy<Superscript>3+</Superscript>, Eu<Superscript>2+</Superscript> multi-color phosphors for warm white light

The novel Ca_4?x(PO₄)₂O: xDy³⁺ and Ca_4?x?y(PO₄)₂O: xDy³⁺, yEu²⁺ multi-color phosphors were synthesized by traditional solid-state reaction. The crystal structure, particle morphology, photoluminescence properties and energy transfer process were investigated in detail. The X-ray diffraction (XRD) results demonstrate that the products showed pure monoclinic phase of Ca₄(PO₄)₂O when x < 0.1. The scanning electron microscopy (SEM) indicated that the phosphors were grain-like morphologies with diameters of ~ 3.7–7.0 μm. Under excitation of 345 nm, Dy³⁺-doped Ca₄(PO₄)₂O phosphors showed multi-color emission bands at 410, 481 and 580 nm originated from oxygen vacancies and Dy³⁺. Interestingly, Ca₄(PO₄)₂O: Dy³⁺, Eu²⁺ phosphors exhibited blue emission band at 481 nm and broad emission band from 530 to 670 nm covering green to red regions. The energy transfer process from Dy³⁺ to Eu²⁺ was observed for the co-doped samples, and the energy transfer efficiency reached to 60% when Eu²⁺ molar concentration was 8%. In particular, warm/cool/day white light with adjustable CCT (2800–6700 K) and high CRI (R_a > 85) can be obtained by changing the Eu²⁺ co-doping contents in Ca₄(PO₄)₂O: Dy³⁺, Eu²⁺ phosphors. The optimized Ca_3.952(PO₄)₂O: 0.04Dy³⁺, 0.008Eu²⁺ phosphor can achieve the typical white light with CCT of 4735 K and CRI of 87.     

Rapid synthesis and enhancement in down conversion emission properties of BaAl<Subscript>2</Subscript>O<Subscript>4</Subscript>:Eu<Superscript>2+</Superscript>,RE<Superscript>3+</Superscript> (RE<Superscript>3+</Superscript>=Y,Pr) nanophosphors

BaAl₂O₄:Eu²⁺,RE³⁺ (RE³⁺=Y, Pr) down conversion nanophosphors were prepared at 600 °C by a rapid gel combustion technique in presence of air using boron as flux and urea as a fuel. A comparative study of the prepared materials was carried out with and without the addition of boric acid. The boric acid was playing the important role of flux and reducer simultaneously. The peaks available in the XPS spectra of BaAl₂O₄:Eu²⁺ at 1126.5 and 1154.8 eV was ascribed to Eu²⁺(3d _5/2) and Eu²⁺(3d _3/2) respectively which confirmed the presence of Eu²⁺ ion in the prepared lattice. Morphology of phosphors was characterized by tunneling electron microscopy. XRD patterns revealed a dominant phase characteristics of hexagonal BaAl₂O₄ compound and the presence of dopants having unrecognizable effects on basic crystal structure of BaAl₂O₄. The addition of boric acid showed a remarkable change in luminescence properties and crystal size of nanophosphors. The emission spectra of phosphors had a broad band with maximum at 490–495 nm due to electron transition from 4f ⁶5d ¹ → 4f ⁷ of Eu²⁺ ion. The codoping of the rare earth (RE³⁺=Y, Pr) ions help in the enhancement of their luminescent properties. The prepared phosphors had brilliant optoelectronic properties that can be properly used for solid state display device applications.     

New,thermally stable Gd<Subscript>11</Subscript>(GeO<Subscript>4</Subscript>)(PO<Subscript>4</Subscript>)<Subscript>3</Subscript>O<Subscript>10</Subscript>-based upconversion phosphors

A series of Gd_11–x–y Yb _x Er _y GeP₃O₂₆ germanate phosphates differing in the ratio of the Yb³⁺ and Er³⁺ active ions have been synthesized, and their luminescence spectra have been measured. According to X-ray diffraction characterization results, all of the synthesized germanate phosphates are single-phase and have a triclinic structure (sp. gr. P1). We have measured upconversion luminescence spectra due to the Er^{3+ 2}H_11/2, ⁴S_3/2 → ⁴I_15/2 and ⁴F_9/2 → ⁴I_15/2 radiative transitions in the synthesized gadolinium ytterbium erbium germanate phosphates and determined the luminescence upconversion energy yield (B _en) in Gd_11–x–y Yb _x Er _y GeP₃O₂₆. The effects of the concentrations and ratio of the dopants in the Gd₁₁(GeO₄)(PO₄)₃O₁₀ germanate phosphate host on B _en and the ratio of the luminescence intensities in the red and green spectral regions (R/G) have been assessed.     

Vapor pressure determination for solid and liquid La<Subscript>2</Subscript>S<Subscript>3</Subscript> using boiling points

A high-temperature technique was developed for vapor pressure determination of solid and liquid γ-La₂S₃ (we called it the boiling point technique). Melting temperatures and total vapor pressures were measured for incongruently vaporizing γ-La₂S₃ at 1853–2210 K and 0.3–3.0 atm pressures. Having compared the slopes of the log p(S₂) versus 1/T plots measured by various techniques, we recommend the equation log p(S₂) [atm] = (6.31 ± 0.15) ? (12720±310)T ^?1 for T = 1021–2013 K as the most reliable for practical use.     

Luminescence properties of Bi codoped and P codoped Ca<Subscript>3</Subscript>(VO<Subscript>4</Subscript>)<Subscript>2</Subscript>:Eu<Superscript>3+</Superscript>

New red emitting phosphors, Ca₃(VO₄)₂:Eu³⁺,Bi³⁺, Ca₃((P,V)O₄)₂:Eu³⁺ were synthesized by low temperature solid-state reaction and characterized by X-ray diffraction, scanning electron microscopy, photoluminescence spectra and Fourier transform infrared spectroscopy. The results show that the red emission located at about 613 nm was ascribed to ⁵ D ₀-⁷ F ₂ transition of Eu³⁺. The effect of by Bi doping and by P doping was also investigated systematically.     

Photoluminescence of Ga<Subscript>2</Subscript>S<Subscript>3</Subscript>:Eu nanocrystals

The photoluminescence (PL) of Ga₂S₃-5 mol % Eu₂O₃ nanocrystals prepared by mechanical comminution of the initial compound has been studied in the temperature range from 77 to 300 K. It is established that the PL spectrum of nanocrystals, in comparison to that of a massive sample, extends over a broader wavelength interval (430–620 nm) and has two maxima (at 507 and 556 nm) instead of one. The intensity of emission from nanocrystals is significantly higher than that from the massive crystal. The halfwidth in both cases varies with the temperature in proportion to T ^1/2. The intensity of emission at 556 nm for nanocrystals depends on the temperature as lgI ～ 1/T, this dependence having three linear portions corresponding to an activation energy of 0.04, 0.16, and 0.43 eV. The PL bands with maxima at 507 and 556 nm are assigned to the intracenter 4f ⁶5d4f ⁷ transitions in Eu²⁺ ions.     

The calorimetry and thermodynamic functions of Nd Mg<Stack><Subscript>3</Subscript><Superscript>I</Superscript></Stack>Mn<Subscript>4</Subscript>O<Subscript>12</Subscript> (Me<Superscript>I</Superscript>-Li,Na, K) manganites in the range from 298.15 to 673 K

The ceramic technology is employed for synthesizing manganites of composition Nd Mg ₃ ^I Mg₃Mn₄O₁₂(Me^I-Li, Na, K). The X-ray technique is used to find that the compounds crystallize in tetragonal syngony. The parameters of their crystal lattices are determined. Their heat capacities are experimentally determined in the range from 298.15 to 673 K, which enables one to reveal second-order phase transitions. In view of these transitions, equations describing the C _p ^° ～ f(T) dependence are derived, and the thermodynamic functions C _p ^° (T), H°(T)-H°(298.15), S°(T), and Φ ^xx (T) are calculated.     

Upconversion Luminescence of Gd<Subscript>2</Subscript>O<Subscript>3</Subscript> Nanocrystals Doped with Er<Superscript>3+</Superscript> and Yb<Superscript>3+</Superscript> Ions

The upconversion luminescence (UCL) of nanocrystalline gadolinium oxide (Gd₂O₃) doped with Er³⁺ and Yb³⁺ ions has been studied in the temperature range of 90–400 K. The nanocrystals were synthesized by chemical vapor deposition and possessed a cubic crystalline structure with an average particle size within 48–57 nm. It is established that the USL intensity in the red (⁴F_9/2 → ⁴I_15/2 transition in Er3+ ion) and green (⁴S_3/2 → ⁴I_15/2 transition) spectral regions depends on the sample temperature and concentration of dopant ions, as well as on the additional structural defects (anion vacancies) created in the crystal lattice by the introduction of Zn²⁺ ions or irradiation with high-energy (10 MeV) electrons. The luminescence efficiency and spectrum of the upconversion phosphor are determined by energy transfer processes.     

Heat Capacity and thermodynamic functions of DyMe<Superscript>II</Superscript>Cr<Subscript>2</Subscript>O<Subscript>5.5</Subscript>(Me<Superscript>II</Superscript>-Mg,Ca) in the range from 298.15 to 673 K

The calorimetric method is used to investigate the heat capacity of DyMe^IICr₂O_5.5(Me^II-Mg, Ca) chromites in the range from 298.15 to 673 K. The C _p ⁰ ～ f(T) curves exhibit λ-like effects at 348 and 548 K for DyMgCr₂O_5.5 and at 473 K for DyCaCr₂O_5.5, which apparently relate to second-order phase transitions. The temperature dependences are calculated for thermodynamic functions C _p ⁰ (T), H ⁰(T)-H ⁰(298.15), S ⁰(T), and Φ**(T).     

Synthesis and High-Temperature Heat Capacity of Dy<Subscript>2</Subscript>Ge<Subscript>2</Subscript>O<Subscript>7</Subscript> and Ho<Subscript>2</Subscript>Ge<Subscript>2</Subscript>O<Subscript>7</Subscript>

The Dy₂Ge₂O₇ and Ho₂Ge₂O₇ pyrogermanates have been prepared by solid-state reactions in several sequential firing steps in the temperature range 1237–1473 K using stoichiometric mixtures of Dy₂O₃ (or Ho₂O₃) and GeO₂. The heat capacity of the synthesized germanates has been determined as a function of temperature by differential scanning calorimetry in the range 350–1000 K. The experimentally determined C _p (T) curves of the dysprosium and holmium germanates have no anomalies and are well represented by the Maier–Kelley equation. The experimental C _p (T) data have been used to evaluate the thermodynamic functions of the Dy₂Ge₂O₇ and Ho₂Ge₂O₇ pyrogermanates: enthalpy increment H°(T)–H°(350 K), entropy change S°(T)–S°(350 K), and reduced Gibbs energy Ф°(T).     

Synthesis and high-temperature heat capacity of Gd<Subscript>2</Subscript>Sn<Subscript>2</Subscript>O<Subscript>7</Subscript>

Gd₂Sn₂O₇ gadolinium stannate with the pyrochlore structure has been prepared by solid-state reaction and its high-temperature heat capacity has been determined by differential scanning calorimetry in the temperature range 350–1020 K. The C_p(T) data are shown to be well represented by the classic Maier–Kelley equation. The experimental C_p(T) data have been used to evaluate the thermodynamic functions of gadolinium stannate: enthalpy increment H°(T)–H°(339 K), entropy change S°(T)–S°(339 K), and reduced Gibbs energy Ф°(Т).     

Temperature and Magnetic Field-Induced Spin Reorientation in Rare-Earth Perovskite ErFe<Subscript>0.75</Subscript>Cr<Subscript>0.25</Subscript>O<Subscript>3</Subscript>

We report the synthesis of a single-phase rare-earth perovskite ErFe_0.75Cr_0.25O₃ polycrystalline and its magnetic properties. A transition occurs at temperature T _N = 120 K below which we observe a weak magnetic moment from the canted antiferromagnetism. Interestingly, ErFe_0.75Cr_0.25O₃ reveals the compensation-like behavior at T _comp?like = 27 K, where the net magnetic moments of transition-metal ions are antiparallel and equal to the induced net moment of Er³⁺ ions, and the paramagnetic contribution of Er³⁺ moment presenting a nonzero magnetization. The temperature-dependent magnetization measurement shows a spin reorientation transition from Γ₄ to Γ₁ at 6 K. Furthermore, it is also observed that there is a spin-flop transition at low temperature induced by external magnetic field in Γ₁ state (antiferromagnetic state). The interaction between (Fe/Cr)-3d and Er-4f electrons drives an extremely interesting spin reorientation transition which is highly sensitive to magnetic field and temperature.     

High-temperature heat capacity and thermodynamic properties of Tb<Subscript>2</Subscript>Sn<Subscript>2</Subscript>O<Subscript>7</Subscript>

Tb₂Sn₂O₇ has been prepared by solid-state reaction in air at 1473 K over a period of 200 h and its isobaric heat capacity has been studied experimentally in the range 350–1073 K. The C _p(T) data for this compound have no extrema and are well represented by the classic Maier–Kelley equation. The experimental C _p(T) data have been used to evaluate the thermodynamic properties of terbium stannate (pyrochlore structure): enthalpy increment H°(T)–H°(350 K), entropy change S°(T)–S°(350 K), and reduced Gibbs energy Ф°(Т).     

Thermal Dissociation of RMnO<Subscript>3</Subscript> (R = Dy,Yb, Lu)

The phase equilibria involved in the thermal dissociation of RMnO₃ (R = Dy, Yb, Lu) were studied in the range 973–1173 K by a static method in a vacuum circulation unit and by x-ray diffraction analysis of quenched solid phases. The RMnO₃ manganites were shown to dissociate by the reaction RMnO₃ = 1/2R₂O₃ + MnO + 1/4O₂. The temperature dependences of the equilibrium oxygen pressure and Gibbs energy change in this reaction were determined for the three compounds. The experimental data were used to evaluate the standard thermodynamic functions of formation of RMnO₃ from R₂O₃ and Mn₂O₃: ΔH⁰(T) = ?88.93 kJ/mol, Δ S⁰(T) = 46.56 J/(mol K) for DyMnO₃; ΔH⁰(T) = ?130.95 kJ/mol, Δ S⁰(T) = 86.25 J/(mol K) for YbMnO₃; ΔH⁰(T) = ?142.94 kJ/mol, Δ S⁰(T) = 102.87 J/(mol K) for LuMnO₃.     

Critical Temperature of Smart Meta-superconducting MgB<Subscript>2</Subscript>

Enhancing the critical temperature (T _C ) is important not only to widen the practical applications but also to expand the theories of superconductivity. Inspired by the meta-material structure, we designed a smart meta-superconductor consisting of MgB₂ microparticles and Y₂O₃/Eu³⁺ nanorods. In the local electric field, Y₂O₃/Eu³⁺ nanorods generate an electroluminescence (EL) that can excite MgB₂ particles, thereby improving the T _C by strengthening the electron–phonon interaction. An MgB₂-based superconductor doped with one of four dopants of different EL intensities was prepared by an ex situ process. Results showed that the T _C of MgB₂ doped with 2 wt% Y₂O₃, which is not an EL material, is 33.1 K. However, replacing Y₂O₃ with Y₂O₃/Eu³⁺II, which displays a strong EL intensity, can improve the T _C by 2.8 to 35.9 K, which is even higher than that of pure MgB₂. The significant increment in T _C results from the EL exciting effect. Apart from EL intensity, the micromorphology and degree of dispersion of the dopants also affected the T _C . This smart meta-superconductor provides a new method to increase T _C .     

Synthesis and Luminescence Properties of a CsBaGd(MoO<Subscript>4</Subscript>)<Subscript>3</Subscript>:Er<Superscript>3+</Superscript> Phosphor with a Scheelite-Like Structure

A CsBaGd(MoO₄)₃:Er³⁺ phosphor with a scheelite-like structure (sp. gr. P2₁/n) has been synthesized and its luminescence properties have been studied. The synthesized material has been characterized by X-ray diffraction, differential thermal analysis, Raman spectroscopy, and IR spectroscopy.     

Synthesis and luminescence properties of a Li<Subscript>3</Subscript>BaCaY<Subscript>3</Subscript>(MoO<Subscript>4</Subscript>)<Subscript>8</Subscript>:Er<Superscript>3+</Superscript> phosphor with a layered scheelite-like structure

A Li₃BaCaY₃(MoO₄)₈:Er³⁺ phosphor with a scheelite-like structure (sp. gr. C2/c) has been synthesized and its luminescence properties have been studied. The phosphor has been characterized by X-ray diffraction, differential thermal analysis, and IR spectroscopy.     

Study of Magnetic Entropy Change in Nd<Subscript>0.67</Subscript>Ba<Subscript>0.33</Subscript>Mn<Subscript>0.98</Subscript>Fe<Subscript>0.02</Subscript>O<Subscript>3</Subscript> by Means of Theoretical Models

Magnetic entropy change (?ΔS _M ) of Nd_0.67 Ba_0.33Mn_0.98Fe_0.02O₃ perovskite have been analyzed by means of theoretical models. An excellent agreement has been found between the (ΔS_M) values estimated by Landau theory and those obtained using the classical Maxwell relation. In order to estimate the spontaneous magnetization M _{s pont}(T), we used the mean-field theory to analyses the (ΔS_M) vs. M ² data. The obtained M _{s pont}(T) values are in good agreement with those found from the classical extrapolation from the Arrott plots(H/M vs. M ²), confirming that the magnetic entropy is a valid approach to estimate the spontaneous magnetization in our system. At a relatively low magnetic field, a phenomenological model has been used to estimate the values of the magnetic entropy change. The results are in good agreement with those obtained from the experimental data using Maxwell relation.