支撑液膜法提取柠檬酸工艺条件的研究

研究用支撑液膜法提取柠檬酸的工艺过程,讨论了:料液相浓度Cf0、反萃相浓度Cs0、搅拌速度n及操作温度T等工艺条件对传递通量的影响。结果表明,以多孔平板聚丙烯膜为支撑体,在由煤油-TOA-Na2CO3所组成的膜体系中,当Cf0=0.10mol/L,Cs0=0.20mol/L,n=200r/min,T=25℃时,提取率E可达61.3%,与传统工艺相比具有深入研究的价值。     

磷酸三丁酯/煤油支撑液膜体系中苯酚的传质分离

研究了苯酚在以多孔聚丙烯平板膜(Celgard2500)为支撑体、磷酸三丁酯(TBP)为膜载体和煤油为膜溶剂的支撑液膜体系中的传质过程;用传统萃取法测定了TBP/煤油体系中苯酚络合物摩尔比为1∶1,同时得到25.0℃萃取平衡常数为96.72;考察了原料相pH值、初始质量浓度、膜二侧转速、载体浓度和反萃取相碱浓度对苯酚传质的影响,确定了该体系分离苯酚的最佳条件:原料相pH<9,苯酚初始质量浓度<1 000 mg/L,膜二侧转速>300 r/m in,载体浓度为0.55 mol/L,反萃取相碱浓度0.10 mol/L;根据双膜理论提出苯酚的传质动力学方程,采用直线斜率法计算了苯酚在TBP/煤油支撑液膜体系中的扩散层厚度和膜内扩散系数,计算结果表明动力学方程计算值能较好地与实验值吻合,平均相对误差在2%以内。     

PTFE中空纤维膜萃取烟酸工艺研究

以氢氧化钠溶液为萃取剂,采用PTFE中空纤维膜萃取料液中的烟酸,考察了料液相烟酸的初始浓度、料液相初始pH值、料液相与萃取相流量比、萃取剂的初始浓度对烟酸萃取率(η)的影响。结果表明,随着料液初始浓度增大,η增大,当烟酸浓度0.9 g/L时,η减小,但膜通量基本不变,即存在一个最大膜通量,此时烟酸浓度变化对传质无影响;烟酸料液存在一个最佳pH值为4~5;萃取相氢氧化钠浓度增大,η增大;存在一个最佳相流量比(Q料/Q萃)为2.1;温度升高有利于膜萃取。     

Cu2+在支撑液膜中的传质过程

研究了以疏水性多孔聚丙烯膜(Celgard 2500)为支撑体和LIX984的煤油溶液为膜液的支撑液膜体系萃取Cu2+的传质过程. 采用双膜理论描述Cu2+通过平板支撑液膜的传质过程,建立了其在稳态下的传质动力学方程,且当反萃取侧酸浓度大于2 mol/L时,反萃取侧的传质阻力可以忽略;利用膜内分传质系数km表征支撑液膜膜液的流失行为,在传质过程中,km先增大而后逐渐减小,且载体的流失速率大于稀释剂煤油的流失速率. 考察了操作条件对传质和膜液流失速率的影响,结果表明,Cu2+初始传质通量随载体初始浓度、料液初始pH值和料液初始Cu2+浓度的增大而增大;载体初始浓度越大,膜液流失越快;料液初始Cu2+浓度增大,膜液流失越慢;料液相pH值的改变对膜液流失速率没有影响.     

萃取凝胶膜过程工艺条件对镍离子传质效率及稳定性增进

利用交联反应在PVDF超滤膜表面创新性的构建含有萃取剂磷酸二异辛酯的聚二甲基硅氧烷-正硅酸乙酯体系萃取凝胶膜（EGM）;并对其基本物理化学性质进行了表征。研究了EGM过程中料液相循环方式、料液相及反萃相浓度与流量、水相温度、组件装填密度等工艺条件对镍离子传质性能及EGM运行稳定性的影响规律。9 h实验结果表明在室温水相温度为22℃条件下,当工艺运行条件为料液相流量1900 ml·min^-1、反萃相流量93 ml·min^-1、组件装填密度14%、料液相循环于壳程时,EGM对镍离子的萃取性能及稳定性达到最佳值。在此基础上,对该系统进行了60 h稳定性实验,并与传统支撑液膜进行了对比。结果显示传统支撑液膜持续运行35 h后通量降为0,衰减率为100%;而EGM持续运行60 h后通量衰减率仅为27.1%;同时EGM初始传质通量相比于传统支撑液膜提高了6.8倍,体现了EGM过程在传质通量大幅提升和长期运行稳定性显著增进方面具有双重优势。     

PTFE中空纤维膜萃取苯甲酸工艺研究

以氢氧化钠溶液为萃取剂,采用PTFE中空纤维膜萃取料液中的苯甲酸,考察了料液相苯甲酸的初始浓度、料液相初始pH、料液相与萃取相流量比、萃取剂的初始浓度对苯甲酸萃取率(η)的影响。结果表明,随着料液初始浓度增大,η增大,当苯甲酸浓度1 g/L时,η减小,但膜通量基本不变,即存在一个最大膜通量,此时苯甲酸浓度变化对传质无影响;料液的pH值下降,η增大;萃取相氢氧化钠浓度增大,η增大;存在一个最佳相流量比(Q料/Q萃)为1.8。另外,温度升高有利于膜萃取。     

萃取凝胶膜过程工艺条件对镍离子传质效率及稳定性增进

利用交联反应在PVDF超滤膜表面创新性的构建含有萃取剂磷酸二异辛酯的聚二甲基硅氧烷-正硅酸乙酯体系萃取凝胶膜(EGM);并对其基本物理化学性质进行了表征。研究了EGM过程中料液相循环方式、料液相及反萃相浓度与流量、水相温度、组件装填密度等工艺条件对镍离子传质性能及EGM运行稳定性的影响规律。9 h实验结果表明在室温水相温度为22℃条件下,当工艺运行条件为料液相流量1900 ml·min~(-1)、反萃相流量93 ml·min~(-1)、组件装填密度14%、料液相循环于壳程时,EGM对镍离子的萃取性能及稳定性达到最佳值。在此基础上,对该系统进行了60 h稳定性实验,并与传统支撑液膜进行了对比。结果显示传统支撑液膜持续运行35 h后通量降为0,衰减率为100%;而EGM持续运行60 h后通量衰减率仅为27.1%;同时EGM初始传质通量相比于传统支撑液膜提高了6.8倍,体现了EGM过程在传质通量大幅提升和长期运行稳定性显著增进方面具有双重优势。     

柠檬酸铁处理高浓度硫化氢炼厂酸性气的研究

通过选择柠檬酸配位剂和其它助剂．研究柠檬酸铁处理高浓度硫化氢炼厂酸性气体。实验分别考察了吸收剂Fe（111）L浓度、溶液pH值、操作温度、硫化氢气体流量及传质方式对硫化氢吸收率的影响．确定柠檬酸铁脱硫体系适宜的反应条件。推荐最佳工艺参数为：柠檬酸铁浓度为0．6mol／L、pH8．5～9．0、操作温度40℃、配备合适的分布器、硫化氢气体流量以低于0．12m^3／h为宜。在最佳条件下HzS脱除率100％．反应中生成的硫磺可以通过过滤的方法除去。实验结果表明．利用柠檬酸铁处理含高浓度H2S的炼厂酸性气体具有工艺简单、脱除效率高、投资少、运行费用低等特点。     

乳化液膜提取柠檬酸及其溶胀的研究

本文研究了采用Ｗ／Ｏ型乳化液膜提取水溶液中的柠檬酸，同时研究了柠檬酸提取过程中水的传质行为（乳液溶胀）。考察了表面活性剂、载体、反萃剂Ｎａ２ＣＯ３、柠檬酸浓度对柠檬酸传质和乳液溶胀的影响。实验结果表明：萃取率随载体和内相试剂浓度的增加而增加；当载体和初始柠檬酸浓度较高时，乳液更易于溶胀，由此得出了除渗透压造成的乳液溶胀外，溶质与载体形成的络合物也能促成乳液的溶胀。提出了分离浓缩柠檬酸的最佳乳液配方     

柠檬酸铁处理高浓度硫化氢炼厂酸性气的研究

通过选择柠檬酸配位剂和其它助剂，研究柠檬酸铁处理高浓度硫化氢炼厂酸性气体。实验分别考察了吸收剂Fe（Ⅲ）L浓度、溶液pH值、操作温度、硫化氢气体流量及传质方式对硫化氢吸收率的影响．确定柠檬酸铁脱硫体系适宜的反应条件。推荐最佳工艺参数为：柠檬酸铁浓度为0．6mol／L、pH8．5～9．0、操作温度40℃、配备合适的分布器、硫化氧气体流量以低于0．12m^3／h为宜。在最佳条件下H2S脱除率100％，反应中生成的硫磺可以通过过滤的方法除去。实验结果表明。利用柠檬酸铁处理含高浓度H2S的炼厂酸性气体具有工艺简单、脱除效率高、投资少、运行费用低等特点。     

Insect antifeedant properties of anthranoids from the genusVismia

Vismiones and ferruginins, representatives of a new class of lypophilic anthranoids from the genusVismia were found to inhibit feeding in larvae of species ofSpodoptera, Heliothis, and inLocusta migratoria.     

Direct observation of freeze-thaw instability of latex coatings via high pressure freezing and cryogenic SEM

Despite its industrial importance, the subject of freeze-thaw (F/T) stability of latex coatings has not been studied extensively. There is also a lack of fundamental understanding about the process and the mechanisms through which a coating becomes destabilized. High pressure (2100 bar) freezing fixes the state of water-suspended particles of polymer binder and inorganic pigments without the growth of ice crystals during freezing that produce artifacts in direct imaging scanning electron microscopy (SEM) of fracture surfaces of frozen coatings. We show that by incorporating copolymerizable functional monomers, it is possible to achieve F/T stability in polymer latexes and in low-VOC paints, as judged by the microstructures revealed by the cryogenic SEM technique. Particle coalescence as well as pigment segregation in F/T unstable systems are visualized. In order to achieve F/T stability in paints, latex particles must not flocculate and should provide protection to inorganic pigment and extender particles. Because of the unique capabilities of the cryogenic SEM, we are able to separate the effects of freezing and thawing, and study the influence of the rate of freezing and thawing on F/T stability. Destabilization can be caused by either freezing or thawing. A slow freezing process is more detrimental to F/T stability than a fast freezing process; the latter actually preserves suspension stability during freezing. Presented at the 82nd Annual Meeting of the Federation of Societies for Coatings Technology, October 27–29, 2004 in Chicago, IL. Tied for first place in The John A. Gordon Best Paper Competition.     

Ethanol and (−)-α-Pinene: Attractant Kairomones for Bark and Ambrosia Beetles in the Southeastern US

In 2002–2004, we examined the flight responses of 49 species of native and exotic bark and ambrosia beetles (Coleoptera: Scolytidae and Platypodidae) to traps baited with ethanol and/or (−)-α-pinene in the southeastern US. Eight field trials were conducted in mature pine stands in Alabama, Florida, Georgia, North Carolina, and South Carolina. Funnel traps baited with ethanol lures (release rate, about 0.6 g/day at 25–28°C) were attractive to ten species of ambrosia beetles (Ambrosiodmus tachygraphus, Anisandrus sayi, Dryoxylon onoharaensum, Monarthrum mali, Xyleborinus saxesenii, Xyleborus affinis, Xyleborus ferrugineus, Xylosandrus compactus, Xylosandrus crassiusculus, and Xylosandrus germanus) and two species of bark beetles (Cryptocarenus heveae and Hypothenemus sp.). Traps baited with (−)-α-pinene lures (release rate, 2–6 g/day at 25–28°C) were attractive to five bark beetle species (Dendroctonus terebrans, Hylastes porculus, Hylastes salebrosus, Hylastes tenuis, and Ips grandicollis) and one platypodid ambrosia beetle species (Myoplatypus flavicornis). Ethanol enhanced responses of some species (Xyleborus pubescens, H. porculus, H. salebrosus, H. tenuis, and Pityophthorus cariniceps) to traps baited with (−)-α-pinene in some locations. (−)-α-Pinene interrupted the response of some ambrosia beetle species to traps baited with ethanol, but only the response of D. onoharaensum was interrupted consistently at most locations. Of 23 species of ambrosia beetles captured in our field trials, nine were exotic and accounted for 70–97% of total catches of ambrosia beetles. Our results provide support for the continued use of separate traps baited with ethanol alone and ethanol with (−)-α-pinene to detect and monitor common bark and ambrosia beetles from the southeastern region of the US.     

Methyl 2,4,6-decatrienoates Attract Stink Bugs and Tachinid Parasitoids

Halyomorpha halys (Stål) (Pentatomidae), called the brown marmorated stink bug (BMSB), is a newly invasive species in the eastern USA that is rapidly spreading from the original point of establishment in Allentown, PA. In its native range, the BMSB is reportedly attracted to methyl (E,E,Z)-2,4,6-decatrienoate, the male-produced pheromone of another pentatomid common in eastern Asia, Plautia stali Scott. In North America, Thyanta spp. are the only pentatomids known to produce methyl 2,4,6-decatrienoate [the (E,Z,Z)-isomer] as part of their pheromones. Methyl 2,4,6-decatrienoates were field-tested in Maryland to monitor the spread of the BMSB and to explore the possibility that Thyanta spp. are an alternate host for parasitic tachinid flies that use stink bug pheromones as host-finding kairomones. Here we report the first captures of adult and nymph BMSBs in traps baited with methyl (E,E,Z)-2,4,6-decatrienoate in central Maryland and present data verifying that the tachinid, Euclytia flava (Townsend), exploits methyl (E,Z,Z)-2,4,6-decatrienoate as a kairomone. We also report the unexpected finding that various isomers of methyl 2,4,6-decatrienoate attract Acrosternum hilare (Say), although this bug apparently does not produce methyl decatrienoates. Other stink bugs and tachinids native to North America were also attracted to methyl 2,4,6-decatrienoates. These data indicate there are Heteroptera in North America in addition to Thyanta spp. that probably use methyl 2,4,6-decatrienoates as pheromones. The evidence that some pentatomids exploit the pheromones of other true bugs as kairomones to find food or to congregate as a passive defense against tachinid parasitism is discussed.     

2007～2008年世界塑料工业进展

收集了2007年7月～2008年6月世界塑料工业的相关资料,介绍了2007～2008年国外塑料工业的发展情况,提供了世界塑料产量、消费量及全球各类树脂的需求量及产能情况.按通用热塑性树脂(聚乙烯、聚丙烯、聚苯乙烯、聚氯乙烯、ABS树脂)、工程塑料(尼龙、聚碳酸酯、聚甲醛、热塑性聚酯、聚苯醚)、特种工程塑料(聚苯·硫醚、液晶聚合物、聚醚醚酮)、通用热固性树脂(酚醛、聚氨酯、不饱和聚酯树脂、环氧树脂)不同品种的顺序,对树脂的产量、消费量、供需状况及合成工艺、产品应用开发、树脂品种的延伸及应用的进一步扩展等技术作了详细介绍.     

2005～2006年国外塑料工业进展

收集了2005年7月～2006年6月国外塑料工业的相关资料,介绍了2005—2006年国外塑料工业的发展情况。提供了世界塑料产量、消费量及全球各类树脂生产量以及各国塑料制品的进出口情况。作为对比,介绍了中国塑料的生产情况。按通用热塑性树脂（聚乙烯、聚丙烯、聚苯乙烯、聚氯乙烯、ABS树脂）、工程塑料（聚酰胺、聚碳酸酯、聚甲醛、热塑性聚酯、聚苯醚）、通用热固性树脂（酚醛、聚氨酯、不饱和树脂、环氧树脂）、特种工程塑料（聚苯硫醚、液晶聚合物、聚醚醚酮）的品种顺序,对树脂的产量、消费量、供需状况及合成工艺、产品开发、树脂品种的延伸及应用的扩展作了详细的介绍。