Preparation and properties of phosphoric acid doped sulfonated poly(tetra phenyl phthalazine ether sulfone) copolymers for high temperature proton exchange membrane application

Phosphoric acid-doped sulfonated poly(tetra phenyl phthalazine ether sulfone) (PA-SPTPPES) copolymers were successfully synthesized by the 4,4′-dihydroxydiphenylsulfone with 1,2-bis(4-fluorobenzoyl)-3,4,5,6-tetraphenylbenzene (BFBTPB) and 4,4′-difluorodiphenylsulfone in sulfolane. Poly(tetra phenyl phthalazine ether sulfone)s (PTPPESs) were prepared via an intramolecular ring-closure reaction of dibenzoylbenzene of precursor and hydrazine. The sulfonated poly(tetra phenyl phthalazine ether sulfone) (SPTPPES) membranes were obtained by sulfonation under concentrated sulfuric acid, and followed phosphoric acid-doped by immersion in phosphoric acid. Different contents of doped and sulfonated unit of PA-SPTPPES (10, 15, 20 mol% of BFBTPB) were studied by FT-IR, ¹H NMR spectroscopy, and thermo gravimetric analysis (TGA). The ion exchange capacity (IEC) and proton conductivity of SPTPPESs and PA-SPTPPESs were evaluated with increase of degree of sulfonation and doping level. The PA-SPTPPESs membranes exhibit proton conductivities (80 °C, relative humidity 30%) of 41.3 ∼ 74.1 mS/cm and the maximum power densities of PA-SPTPPES 10, 15, and 20 were about 294, 350, and 403 mW/cm².     

Synthesis and characterization of novel cardo poly(aryl ether sulfone) bearing zwitterionic side groups for proton exchange membranes

A novel series of sulfonated poly(aryl ether sulfone)s with zwitterionic groups ([-CH₂CH₂CH₂N⁺CH₃(CH₂CH₂SO₃⁻)₂]) have been prepared by the copolycondensation of a secondary amine-containing biphenol monomer with 4,4′-biphenol and 4,4′-dichlorodiphenylsulfone, and this was followed by the reaction with sodium 2-bromoethanesulfonate. All the resulting copolymers can form uniform and tough membranes by simple solution casting. The investigation of ion exchange capacity (IEC) values indicated that each ammonium group interacted with one sulfonate group. Because of strong intermolecular interaction, the increased packing density of chain formed that resulted in polymer membranes with lower water uptake and swelling ratio, and better oxidative stability compared with side-chain-type sulfonated poly(aryl ether sulfone)s with the close IEC values. The polymer membranes bearing zwitterionic groups kept intact in Fenton’s reagent at 80 °C for 20 h. Furthermore, these membranes demonstrated higher proton conductivity than the side-chain-type sulfonated polymer membranes at the same measurement conditions.     

Composite membranes based on a sulfonated poly(arylene ether sulfone) and proton-conducting hybrid silica particles for high temperature PEMFCs

The organic-inorganic composite membranes are prepared by inserting poly(styrene sulfonate)-grafted silica particles into a polymer matrix of sulfonated poly(arylene ether sulfone) copolymer. The first step consisted in using atom transfer radical polymerization method to prepare surface-modified silica particles grafted with sodium 4-styrenesulfonate, referred to as PSS-g-SiO₂. Ion exchange capacities up to 2.4 meq/g are obtained for these modified silica particles. In a second step, a sulfonated poly(arylene ether sulfone) copolymer is synthesized via nucleophilic step polymerization of sulfonated 4,4′-dichlorodiphenyl sulfone, 4,4′-dichlorodiphenyl sulfone and phenolphthalin monomers in the presence of potassium carbonate. The copolymer is blended with various amounts of silica particles to form organic-inorganic composite membranes. Esterification reaction is carried out between silica particles and the sulfonated polymer chains by thermal treatment in the presence of sodium hypophosphite, which catalyzed the esterification reaction. The water uptake, proton conductivity, and thermal decomposition temperature of the membranes are measured. All composite membranes show better water uptake and proton conductivity than the unmodified membrane. Moreover, the membranes are tested in a commercial single cell at 80 °C and 120 °C in humidified H₂/air under different relative humidity conditions. The composite membrane containing 10%(w/w) of PSS-g-SiO₂ particles, which have ester bonds between polymer chains and silica particles, showed the best performance of 690 mA cm⁻² at 0.6 V, 120 °C and 30 %RH, even higher than the commercial Nafion^® 112 membrane.     

Amelioration in physicochemical properties and single cell performance of sulfonated poly(ether ether ketone) block copolymer composite membrane using sulfonated carbon nanotubes for intermediate humidity fuel cells

A composite membrane composed of a sulfonated diblock copolymer (SDBC) based on poly(ether ether ketone) blocks copolymerized with partially fluorinated poly(arylene ether sulfone) and sulfonated carbon nanotubes (SCNTs) was fabricated by simple solution casting. Addition of the SCNT filler enhanced the water absorption and proton conductivity of membranes because of the increased per‐cluster volume of sulfonic acid groups, at the same time reinforced the membranes' thermal and mechanical properties. The SDBC/SCNT‐1.5 membrane exhibited the most improved physicochemical properties among all materials. It obtained a proton conductivity of 10.1 mS/cm at 120°C under 20% relative humidity (RH) which was 2.6 times more improved than the pristine membrane (3.9 mS/cm). Moreover, the single cell performance of the SDBC/SCNT‐1.5 membrane at 60°C and 60% RH at ambient pressure exhibited a peak power density of 171 mW/cm² at a load current density of 378 mA/cm², while the pristine membrane exhibited 119 mW/cm² at a load current density of 294 mA/cm². Overall, the composite membrane exhibited very promising characteristics to be used as polymer electrolyte membrane in fuel cells operated at intermediate RH.     

Direct methanol fuel cell performance of sulfonated poly (2,6-dimethyl-1,4-phenylene oxide)-polybenzimidazole blend proton exchange membranes

Various sulfonated poly (2,6-dimethyl-1,4-phenylene oxide) (SPPO)-polybenzimidazole (PBI) blend membranes were prepared and investigated as proton exchange membranes (PEMs) for direct methanol fuel cell (DMFC) applications. With increasing PBI content water swelling, ion exchange capacity, proton conductivity and methanol permeability of SPPO-PBI membranes were found to be decreased due to acid-base interactions between sulfonate and the amine groups of the blended components. Among various SPPO-PBI blend membranes, 80:20 wt% was found as the optimum composition, which showed the highest membrane selectivity parameter. Direct methanol-air single fuel cell tests revealed a higher cell efficiency of 11.6% for SPPO80-PBI20 than 10.9% for Nafion^®117 at 5 M methanol feed, and also a higher power density of 57.6 mW.cm⁻² compared to 39.4 mW.cm⁻² for Nafion^®117. Transport properties as well as DMFC performance results of SPPO-PBI blend PEMs converge to indicate their potential for DMFC applications.     

Construction of a new continuous proton transport channel through a covalent crosslinking reaction between carboxyl and amino groups

Sulfonated poly(arylene ether ketone sulfone) bearing pendant carboxylic acid groups (C-SPAEKS) and sulfonated poly(arylene ether ketone sulfone) containing amino groups (Am-SPAEKS) were used to prepare C-SPAEKS/Am-SPAEKS crosslinked membranes. ¹H NMR and Fourier transform infrared spectra proved that C-SPAEKS and Am-SPAEKS copolymers, as well as C-SPAEKS/Am-SPAEKS crosslinked membrane, were successfully synthesized. TEM images showed that a continuous proton transport channel formed after crosslinking. Thermogravimetric analysis curves demonstrated that the thermal property of the crosslinked membranes improved. The crosslinked membranes exhibited suitable mechanical properties at 25 and 80 °C. The methanol permeability of C-SPAEKS/Am-SPAEKS-40 was 2.35 × 10⁻⁷ cm² s⁻¹ at 60 °C, which was lower than that of C-SPAEKS (24.12 × 10⁻⁷ cm² s⁻¹) and Am-SPAEKS (17.91 × 10⁻⁷ cm² s⁻¹). The proton conductivity of C-SPAEKS/Am-SPAEKS-40 was 0.089 S cm⁻¹, which was higher than that of C-SPAEKS and Am-SPAEKS at 80 °C. The results proved that C-SPAEKS/Am-SPAEKS crosslinked membranes were potential proton exchange membranes for direct methanol fuel cell applications.     

Improved proton conduction of sulfonated poly (ether ether ketone) membrane by sulfonated covalent organic framework nanosheets

A type of sulfonated covalent organic framework nanosheets (TpPa-SO₃H) was synthesized via interfacial polymerization and incorporated into sulfonated poly (ether ether ketone) (SPEEK) matrix to prepare proton exchange membranes (PEMs). The densely and orderly arranged sulfonic acid groups in the rigid skeleton of the TpPa-SO₃H nanosheets, together with their high-aspect-ratio and well-defined porous structure provide proton-conducting highways in the membrane. The doping of TpPa-SO₃H nanosheets led to an increased ion exchange capacity up to 2.34 mmol g^?1 but a 2-folds reduced swelling ratio, remarkably mitigating the trade-off between high IEC and excessive swelling ratio. Based on the high IEC and orderly arranged proton-conducting sites, the SPEEK/TpPa–SO₃H–5 membrane exhibited the maximum proton conductivity of 0.346 S cm^?1 at 80 °C, 1.91-folds higher than the pristine SPEEK membrane. The mechanical strength of the composite membrane was also improved by 2.05-folds–74.5 MPa. The single H₂/O₂ fuel cell using the SPEEK/TpPa–SO₃H–5 membrane presented favorable performance with an open voltage of 1.01 V and a power density of 86.54 mW cm^?2.     

An effective strategy to enhance the performance of the proton exchange membranes based on sulfonated poly(ether ether ketone)s

We report an effective and facile approach to enhance the dimensional and chemical stability of sulfonated poly(ether ether ketone) (SPEEK) type proton exchange membranes through simple polymer blending for fuel cell applications, using commercial available materials. The polymeric blends with sulfonated poly(aryl ether sulfone)s (SPAES) were simply fabricated by a three-component system, which contained SPEEK (10–50 wt%, 1.83 mmol/g), and SPAES-40 (1.72 mmol/g)/SPAES-50 (2.04 mmol/g) at 1:1 in weight. The SPAES-40 was selected for mechanical and dimensional stability reinforcing, while SPAES-50 for the good polymer compatibility. The obtained SPEEK/SPAES blend membranes showed depressed water uptake, better dimensional and oxidative stability, together with higher proton conductivity beyond 70 °C than the pristine SPEEK membrane. The apparent improvements in membrane properties were associated with the homogeneous dispersion of SPEEK and both SPAES copolymers inside the membranes as well as the rearrangements of the polymeric chains. The SPEEK content should be properly controlled in the range of 10–40% (B10 to B40). In a H₂/O₂ fuel cell test, B30 showed a maximum power density of 700 mW/cm², which was 1.6 times as high as that of B40 at 80 °C under 100% RH. The further cross-linking treatment produced more ductile and enduring blend membranes, indicating an appreciable prospective for fuel cell applications.     

Facile synthesis of poly (arylene ether ketone)s containing flexible sulfoalkyl groups with enhanced oxidative stability for DMFCs

After tethering sodium 2-mercaptoethanesulfonate (MTS) to the bromomethylated poly(arylene ether ketone) precursor, a novel clustered sulfonated poly(arylene ether ketone) containing flexible sulfoalkyl groups (MTSPAEK) was prepared and used as polymer electrolyte membrane for application in DMFCs. The chemical structure and the degree of grafting of MTSPAEK copolymers were identified by ¹H NMR spectra. The resulted MTSPAEK copolymers exhibited excellent thermal stability (T_d5% > 259 °C) and good mechanical properties (tensile strength at break > 52 MPa). Compared to conventional sulfonated aromatic hydrocarbon polymers, MTSPAEK membranes displayed enhanced oxidative stability in Fenton's reagent owing to the elimination of free radicals by the sulfide groups located on the polymer side chains. Especially, MTSPAEK-2.10 with the highest content of flexible sulfoalkyl groups exhibited a highest proton conductivity of 0.181 S cm⁻¹ at 80 °C. It could be attributed to the obvious hydrophilic/hydrophobic phase-separated structure within the membrane, which was confirmed by AFM images. Moreover, MTSPAEK-2.10 membrane performed a peak power density of 70 mW cm⁻² in DMFC when feeding with 2 M methanol at 80 °C, which was comparable to the performance of recast Nafion as reported. Therefore, the combination of good thermal stability and mechanical properties, good oxidative stability, and good methanol barrier performance of MTSPAEK membranes indicated that they have potential to be alternative materials for PEMs in DMFCs.     

Robust proton exchange membrane for vanadium redox flow batteries reinforced by silica-encapsulated nanocellulose

High ion selectivity and mechanical strength are critical properties for proton exchange membranes in vanadium redox flow batteries. In this work, a novel sulfonated poly(ether sulfone) hybrid membrane reinforced by core-shell structured nanocellulose (CNC-SPES) is prepared to obtain a robust and high-performance proton exchange membrane for vanadium redox flow batteries. Membrane morphology, proton conductivity, vanadium permeability and tensile strength are investigated. Single cell tests at a range of 40–140 mA cm⁻² are carried out. The performance of the sulfonated poly(ether sulfone) membrane reinforced by pristine nanocellulose (NC-SPES) and Nafion® 212 membranes are also studied for comparison. The results show that, with the incorporation of silica-encapsulated nanocellulose, the membrane exhibits outstanding mechanical strength of 54.5 MPa and high energy efficiency above 82% at 100 mA cm⁻², which is stable during 200 charge-discharge cycles.     

4-Aminopyridine grafted sulfonated poly(arylene ether ketone sulfone) proton exchange membrane with high relative selectivity for fuel cells

A series of sulfonated poly(arylene ether ketone sulfone)s polymer having a degree of sulfonation of 80% and a carboxyl group in the side chain (C-SPAEKS) were prepared by polycondensation. The 4-aminopyridine grafted sulfonated poly(arylene ether ketone sulfone)s polymer membranes (SPPs) were prepared by amidation reaction with the carboxyl group to immobilize 4-aminopyridine on the side chain. The ¹H NMR results and Fourier transform infrared of SPP membranes demonstrated the successful grafting of the 4-aminopyridine. Proton conductivity, water absorption, swelling ratio, and thermal stability of different proportions of SPP membranes were investigated under the different conditions. With the increase of pyridine grafting content, the methanol permeability coefficient of the membrane decreased significantly from 8.17 × 10⁻⁷ cm²s⁻¹ to 8.92 × 10⁻⁸ cm²s⁻¹ at 25 °C. And, the proton conductivity and relative selectivity of the membrane were positively correlated with the grafted pyridine content. Among them, the SPP-4 membrane exhibited the highest proton conductivity of 0.088 Scm⁻¹ at 100 °C. The relative selectivity increased from 4.73 × 10⁴ S scm⁻³ to 9.84 × 10⁴ S scm⁻³.     

Composite membranes based on sulfonated poly(aryl ether ketone)s containing the hexafluoroisopropylidene diphenyl moiety and poly(amic acid) for proton exchange membrane fuel cell application

Composite membranes based on sulfonated poly(aryl ether ketone)s containing the hexafluoroisopropylidene diphenyl moiety and poly(amic acid) with oligoaniline in the main chain have been prepared and immersed in H₃PO₄ to obtain acid-doped composite films. As expected, the water uptake values and methanol permeability of the composite membranes decrease with the increase of the weight fraction of PAA in the membrane matrix. Notably, the SPEEK-6F/PAA-15 shows a water uptake of 13.2% and a methanol permeability of 0.9 × 10⁻⁷ cm² s⁻¹, which are much lower than those of the Nafion (28.6% and 15.5 × 10⁻⁷ cm² s⁻¹, respectively). Although the proton conductivities decrease after the addition of PAA, higher selectivity values are obtained with the composite membranes. Therefore, the SPEEK-6F/PAA blend membranes, with the improved proton conductivity, methanol resistance and good thermal stability, can be used as a good alternative for proton conductive membranes with potential application in proton exchange membrane fuel cells (PEMFCs).     

Preparation and characterization of sulfonated amine-poly(ether sulfone)s for proton exchange membrane fuel cell

Sulfonated amine-poly(ether sulfone)s (S-APES)s were prepared by nitration, reduction and sulfonation of poly(ether sulfone) (ultrason^®-S6010). Poly(ether sulfone) was reacted with ammonium nitrate and trifluoroacetic anhydride to produce the nitrated poly(ether sulfone), and was followed by reduction using tin(II)chloride and sodium iodide as reducing agents to give the amino-poly(ether sulfone). The S-APES was obtained by reaction of 1,3-propanesultone and the amino-poly(ether sulfone) (NH₂-PES) with sodium methoxide. The different degrees of nitration and reduction of poly(ether sulfone) were successfully synthesized by an optimized process. The reduction of nitro group to amino was done quantitatively, and this controlled the contents of the sulfonic acid group. The films were converted from salt to acid forms with dilute hydrochloric acid. Different contents of sulfonated unit of the S-APES were studied by FT-IR, ¹H NMR spectroscopy, differential scanning calorimetry (DSC), and thermo gravimetric analysis (TGA). Sorption experiments were conducted to observe the interaction of sulfonated polymers with water and methanol. The ion exchange capacity (IEC), a measure of proton conductivity, was evaluated. The S-APES membranes exhibit conductivities (25 °C) from 1.05 × 10⁻³ to 4.83 × 10⁻³ S/cm, water swell from 30.25 to 66.50%, IEC from 0.38 to 0.82 meq/g, and methanol diffusion coefficients from 3.10 × 10⁻⁷ to 4.82 × 10⁻⁷ cm²/S at 25 °C.     

A facile,effective thermal crosslinking to balance stability and proton conduction for proton exchange membranes based on blend sulfonated poly(ether ether ketone)/sulfonated poly(arylene ether sulfone)

The development of hydrocarbon polymer electrolyte membranes with high proton conductivities and good stability as alternatives to perfluorosulfonic acid membranes is an ongoing research effort. A facile and effective thermal crosslinking method was carried out on the blended sulfonated poly (ether ether ketone)/poly (aryl ether sulfone) (SPEEK/SPAES) system. Two SPEEK polymers with ion exchange capacities (IECs) of 1.6 and 2.0 mmol g^?1 and one SPAES polymer (2.0 mmol g^?1) were selected to create different blends. The effect of thermal crosslinking on the fundamental properties of the membranes, especially their physicochemical stability and electrochemical performance, were investigated in detail. The homogeneous and flexible thermally-crosslinked SPEEK/SPAES membranes displayed excellent mechanical toughness (27–46 Mpa), suitable water uptake (<60%), high dimensional stability (swelling ratio < 15%) and large proton conductivity (>120 mS cm^?1) at 80 °C. The thermal crosslinking membranes also show significantly enhanced hydrolytic (<2.5%) and oxidative stability (<2%). Fuel cell with t-SPEEK/SPAES (1:2:2) membrane achieves a power density of 665 mW cm^?2 at 80 °C.     

Synthesis and properties of sulfonated poly(arylene ether ketone sulfone) containing amino groups/functional titania inorganic particles hybrid membranes for fuel cells

In this work, the organic-inorganic hybrid membranes were prepared. The synthesis and properties of the hybrid membranes were investigated. The sulfonated poly(arylene ether ketone sulfone) containing amino groups (Am-SPAEKS) was synthesized by nucleophilic polycondensation. The sol-gel method was used to prepared functional titania inorganic particles (L-TiO₂). The ¹H NMR and FT-IR were performed to verified the structure of Am-SPAEKS and L-TiO₂. The organic-inorganic hybrid membranes showed both good thermal stabilities and mechanical properties than that of Am-SPAEKS. The L-Am-15% membrane exhibited the highest Young's modulus (2262.71 MPa) and Yield stress (62.09 MPa). The distribution of L-TiO₂ particles was revealed by SEM. Compared to Am-SPAEKS, the hybrid membranes showed higher proton conductivities. The L-Am-15% exhibited the highest proton conductivity of 0.0879 S cm⁻¹ at 90 °C. The results indicate that the organic-inorganic hybrid membranes have potential for application in proton exchange membrane fuel cells.     

New highly proton-conducting membrane based on sulfonated poly(arylene ether sulfone)s containing fluorophenyl pendant groups,for low-temperature polymer electrolyte membrane fuel cells

A novel series of sulfonated poly(arylene ether sulfone)s (SPAESs) containing fluorophenyl pendant groups are successfully developed and their membranes are evaluated in low-temperature proton exchange membrane fuel cells. The SPAESs are synthesized from 4,4′-dichlorodiphenylsulfone (DCDPS), 3,3′-disulfonate-4,4′-dichlorodiphenylsulfone (SDCDPS), and (4-fluorophenyl)hydroquinone by nucleophilic aromatic substitution polycondensation. The structure and properties of SPAESs membranes are characterized using ¹H-NMR, EA, FT-IR, TG, and DSC, along with the proton conductivity, water uptake, ion exchange capacity and chemical stability. A maximum proton conductivity of 0.35 S cm⁻¹ at 90 °C is achieved for SPAES membrane with 50% SDCDPS. These SPAES membranes display high dimensional stability and oxidative durability, due to the introduction of fluorophenyl pendant groups on the polymer backbone. The fuel cell performances of the MEAs with SPAES reaches an initial power density of 120.6 mW cm⁻² at 30 °C, and greatly increases to 224.3 mW cm⁻² at 80 °C using H₂ and O₂ gases.     

UiO-66-NH2 functionalized cellulose nanofibers embedded in sulfonated polysulfone as proton exchange membrane

Metal–organic frameworks (MOFs) exhibit high proton conductivity, thermal stability, and offer immense flexibility in terms of tailoring their size. Owing to their unique characteristics, they are desirable candidates for proton conductors. Nevertheless, constructing ordered MOF proton channels in proton exchange membranes (PEMs) remains a formidable challenge. Herein, blend nanofibers of cellulose and UiO-66-NH₂ (Cell–UiO-66-NH₂) obtained via the electrospinning process were embedded in a sulfonated polysulfone matrix to obtain high-performance composite PEMs with an orderly arrangement of UiO-66-NH₂. Comprehensive characterization and membrane performance tests reveal that composite membrane with 5 wt% (nominal) UiO-66-NH₂ have revealed high proton conductivity of 0.196 S cm^?1 at 80 °C and 100% relative humidity. Meantime, the composite membrane exhibits a low methanol permeability coefficient (~5.5 × 10^?7 cm² s^?1). Moreover, the composite membrane exhibits a low swelling ratio (17.3%) even at 80 °C. The Cell–UiO-66-NH₂ nanofibers exhibit strong potential for use as a proton-conducting nanofiller in fuel-cell PEMs.     

Enhanced ion conductivity of sulfonated poly(arylene ether sulfone) block copolymers linked by aliphatic chains constructing wide-range ion cluster for proton conducting electrolytes

A series of sulfonated poly(arylene ether sulfone) block copolymers with aliphatic chains (SPAES-LA) to lend structural flexibility in the polymer backbone have been synthesized to prepare proton exchange membranes (PEMs) showing improved electrochemical performance and dimensional/oxidative stabilities. The SPAES-LAs, bearing different hydrophilic/hydrophobic segment lengths, are prepared via polycondensation and sulfonation reactions. The sulfonation reaction occurs in specific fluorenylidene units by using chlorosulfonic acid. The SPAES-LA membrane, fabricated by solvent casting method, exhibits remarkable dimensional/thermal stabilities. Moreover, proton conductivity of as-prepared SPAES-LA membranes demonstrates significant improvement with expansion of ion clusters which is due to the increased hydrophilic volume ratio. In particular, the SPAES-LA-X12Y28 membrane exhibited heightened proton conductivity of 158.4 mS cm⁻¹ as well as suitable dimensional stability and durability towards radical oxidation, due to an effective well-defined hydrophilic-hydrophobic interface. Furthermore, H₂/O₂ fuel cell performance using SPAES-LA-X12Y28 membrane achieves a maximum power density of 232.02 mW cm⁻², a result which points out that SPAES-LA membranes show great potential for applications of polymer electrolyte membrane.     

A highly proton conductive membrane based on hydrolyzed NbCl5 and phytic acid

It is vital to choose economical and environmentally friendly proton conductive materials to improve the performance of proton exchange membranes, which occupies a unique position in proton exchange membrane fuel cells. This paper reports a new proton conductive nanocomposite, that was named NbO₂(OH)-PA prepared from phytic acid (PA) and NbCl₅. NbO₂(OH)-PA showed an excellent proton conductivity of 135 mS cm⁻¹ at 85 °C and 97% relative humidity. In addition, NbO₂(OH)-PA was combined with sulfonated poly (ether ketone) (SPEEK) in different proportions to form proton conductive membranes, that are labeled SPEEK-x NbO₂(OH)-PA. SPEEK-0.9% NbO₂(OH)-PA exhibited the best proton conductivity of 0.17 S cm⁻¹ at 80 °C in water. This work may provide new ideas for improving proton conductivity of membranes through simple methods.     

Conductivity of aromatic-based proton exchange membranes at subzero temperatures

Stable proton exchange membrane (PEM) with good proton conductivity at subzero temperatures is important for the development of PEM fuel cell cold start. In this work, subfreezing conductivity was reported for several aromatic-based PEMs including sulfonated polyimides (SPIs) with three values of ion-exchange capacity (IEC), sulfonated poly(ether ether ketone) (SPEEK) and disulfonated poly(arylene ether sulfone) copolymer (SPSU) as well as Nafion^® 212. Measurements were performed using the electrochemical impedance spectroscopy (EIS) technique. The results showed that only fully hydrated SPEEK (IEC, 1.75) and SPSU (IEC, 2.08) had comparable conductivities with Nafion^® 212 at subzero temperatures. Considering implement of gas purge before subzero storage of PEM fuel cell, the conductivity for those PEMs humidified by water vapor at activity of 0.75 was also investigated. The state of water in aromatic-based PEMs was quantified by differential scanning calorimetry (DSC), and its correlation with conductivity of the membrane was also discussed.