Influence of advanced injection timing on the performance and emissions of CI engine fueled with ethanol‐blended diesel fuel

Ethanol has been considered as an alternative fuel for diesel engines. On the other hand, injection timing is a major parameter that sensitively affects the engine performance and emissions. Therefore, in this study, the influence of advanced injection timing on the engine performance and exhaust emissions of a single cylinder, naturally aspirated, four stroke, direct injection diesel engine has been experimentally investigated when using ethanol‐blended diesel fuel from 0 to 15% with an increment of 5%. The original injection timing of the engine is 27° crank angle (CA) before top dead center (BTDC). The tests were conducted at three different injection timings (27, 30 and 33° CA BTDC) for 30 Nm constant load at 1800 rpm. The experimental results showed that brake‐specific energy consumption (BSEC), brake‐specific fuel consumption (BSFC), NO_x and CO₂ emissions increased as brake‐thermal efficiency (BTE), smoke, CO and HC emissions decreased with increasing amount of ethanol in the fuel mixture. Comparing the results with those of original injection timing, NO_x emissions increased and smoke, HC and CO emissions decreased for all test fuels at the advanced injection timings. For BSEC, BSFC and BTE, advanced injection timings gave negative results for all test conditions. Copyright © 2008 John Wiley & Sons, Ltd.     

Effect of injection timing on the exhaust emissions of a diesel engine using diesel–methanol blends

Environmental concerns and limited resource of petroleum fuels have caused interests in the development of alternative fuels for internal combustion (IC) engines. For diesel engines, alcohols are receiving increasing attention because they are oxygenated and renewable fuels. Therefore, in this study, the effect of injection timing on the exhaust emissions of a single cylinder, naturally aspirated, four-stroke, direct injection diesel engine has been experimentally investigated by using methanol-blended diesel fuel from 0% to 15% with an increment of 5%. The tests were conducted for three different injection timings (15°, 20° and 25 °CA BTDC) at four different engine loads (5 Nm, 10 Nm, 15 Nm, 20 Nm) at 2200 rpm. The experimental test results showed that Bsfc, NO_x and CO₂ emissions increased as BTE, smoke opacity, CO and UHC emissions decreased with increasing amount of methanol in the fuel mixture. When compared the results to those of original injection timing, NO_x and CO₂ emissions decreased, smoke opacity, UHC and CO emissions increased for the retarded injection timing (15 °CA BTDC). On the other hand, with the advanced injection timing (25 °CA BTDC), decreasing smoke opacity, UHC and CO emissions diminished, and NO_x and CO₂ emissions boosted at all test conditions. In terms of Bsfc and BTE, retarded and advanced injection timings gave negative results for all fuel blends in all engine loads.     

Using renewable n-octanol in a non-road diesel engine with some modifications

n-Octanol is a promising biofuel synthesized from biomass with several properties closer to diesel than the more popularly researched n-butanol. This study investigates the effects of injection timing (2°CA advance & retard), EGR (up to 30%) and Oct30 (30% by vol. of n-octanol in diesel) on combustion, performance, and emissions of a DI diesel engine. Results in comparison with diesel indicated Oct30 blend presented an enhanced premixed combustion phasing with higher peaks of pressure and HRR. BSFC was found to be slightly higher for Oct30 blend at all EGR rates. Further, when the injection timing is advanced, the blend produced better BSFC. Oct30 delivered better BTE at all injection timings. NOx and smoke emissions are lower for Oct30 at all conditions. Oct30 could overcome the trade-off between smoke and NOx emissions at a combination of certain EGR and injection timings. It was found that at advanced injection, the reduction in NOx and smoke density was 19.02% and 57.14%, respectively, while BTE increased by 4.6% and BSFC increased by 1.3%. At late injection, a reduction of 50.87% in NOx emissions and 15.87% in smoke density was achieved with a slight drop in BTE by 3.5% and an increase in BSFC by 9.7%.     

A study of spray strategies on improvement of engine performance and emissions reduction characteristics in a DME fueled diesel engine

This paper investigated the impact of injection angle and advance injection timing on combustion, emission, and performance characteristics in a dimethyl ether (DME) fueled compression ignition engine through experimentation on spray behaviors and the use of numerical methods. To achieve this aim, a visualization system and two injectors with different injection angles were used to analyze spray characteristics. The combustion, emission, and performance characteristics were analyzed by numerical methods using a detailed chemical kinetic DME oxidation model. Each of five injection angles and timings were selected to examine the effect of injection angle and timing. It was revealed that the injected spray with narrow injection angles was impinged on the bottom wall after the SOI of BTDC 60°, and most of the fuel spray and evaporation with the wide injection angles had a distribution at the crevice region when the injection timing was advanced. In addition, NO_x emissions at the SOI of BTDC 20° and TDC had higher values, and the soot emission quantities were extremely small. The narrow injection angles had good performance at the advanced injection timing, and the injection timing over a range of BTDC 40-20° showed superiority in performance characteristics.     

The effects of fuel-injection timing at medium injection pressure on the engine characteristics and emissions of a CNG-DI engine fueled by a small amount of hydrogen in CNG

The experiments to determine the effect of fuel-injection timings on engine characteristics and emissions of a DI engine fueled with NG-hydrogen blends (0%, 3%, 5% and 8%) at various engine speeds were conducted. Three injection timings namely 120°, 180° and 300° CA BTDC with a wide open throttle at relative air-fuel ratio, λ = 1.0 were selected. The ignition advance angle was fixed at 30° CA BTDC, while the injection pressure was fixed at 1.4 MPa for all the cases. The tests were firstly performed at low engine speed of 2000 rpm to determine the engine characteristics and emissions. The results showed that the engine performance (e.g. Brake Torque, Brake Power and BMEP), the cylinder pressure and the heat release have the highest values at the injection timing of 180° CA BTDC, followed by the 300° CA BTDC and the 120° CA BTDC. The NO_x emission was found to be highest at the injection timing of 180° CA BTDC. The THC and CO emissions were found to decrease while the CO₂ emission increased with the advancement in the injection timing. The addition of a small amount of hydrogen to the natural gas was found to increase the engine performance, enhance combustion and reduce emissions for any selected injection timings. Secondly, the tests were carried out at variable engine speeds (i.e. 2000 rpm-4000 rpm) in order to further investigate the engine performance. The injection timings of 180° and 300° CA BTDC with CNG-H₂ blends were only selected for comparisons. The injection timing of the 300° CA BTDC was discovered to yield better engine performance as compared to the 180° CA BTDC injection timing after a cutoff engine speed of approximately 2500 rpm.     

Artificial Neural Network based prediction of performance and emission characteristics of a variable compression ratio CI engine using WCO as a biodiesel at different injection timings

Due to the increasing demand for fossil fuels and environmental threat due to pollution a number renewable sources of energy have been studied worldwide. In the present investigation influence of injection timing on the performance and emissions of a single cylinder, four stroke stationary, variable compression ratio, diesel engine was studied using waste cooking oil (WCO) as the biodiesel blended with diesel. The tests were performed at three different injection timings (24°, 27°, 30° CA BTDC) by changing the thickness of the advance shim. The experimental results showed that brake thermal efficiency for the advanced as well as the retarded injection timing was lesser than that for the normal injection timing (27° BTDC) for all sets of compression ratios. Smoke, un-burnt hydrocarbon (UBHC) emissions were reduced for advanced injection timings where as NO_x emissions increased. Artificial Neural Networks (ANN) was used to predict the engine performance and emission characteristics of the engine. Separate models were developed for performance parameters as well as emission characteristics. To train the network, compression ratio, injection timing, blend percentage, percentage load, were used as the input parameters where as engine performance parameters like brake thermal efficiency (BTE), brake specific energy consumption (BSEC), exhaust gas temperature (T_exh) were used as the output parameters for the performance model and engine exhaust emissions such as NO_x, smoke and (UBHC) values were used as the output parameters for the emission model. ANN results showed that there is a good correlation between the ANN predicted values and the experimental values for various engine performance parameters and exhaust emission characteristics and the relative mean error values (MRE) were within 8%, which is acceptable.     

A nonlinear regression based multi-objective optimization of parameters based on experimental data from an IC engine fueled with biodiesel blends

This study reports the results of an experimental investigation of the performance of an IC engine fueled with a Karanja biodiesel blends, followed by multi-objective optimization with respect to engine emissions and fuel economy, in order to determine the optimum biodiesel blend and injection timings complying with Bharat Stage II emission norms. Nonlinear regression has been used to regress the experimentally obtained data to predict the brake thermal efficiency, NO_x, HC and smoke emissions based on injection timing, blend ratio and power output. To acquire the data, experimental studies have been conducted on a single cylinder, constant speed (1500 rpm), direct injection diesel engine under variable load conditions and injection timings for neat diesel and various Karanja biodiesel blends (5%, 10%, 15%, 20%, 50% and 100%). Retarding the injection timing for neat Karanja biodiesel resulted in an improved efficiency and lower HC emissions. A tradeoff relationship between the NO_x and smoke emissions is observed, which makes it difficult to determine the optimum blend ratio. The functional relationship developed between the correlating variables using nonlinear regression is able to predict the performance and emission characteristics with a correlation coefficient (R) in the range of 0.95-0.99 and very low root mean square errors. The outputs obtained using these functions are used to evaluate the multi-objective function of optimization process in the 0-20% blend range. The overall optimum is found to be 13% biodiesel-diesel blend with an injection timing of 24°bTDC, when equal weightage is given to emissions and efficiency.     

Effect of fuel injection timing and injection pressure on performance in a hydrogen direct injection engine

The in-cylinder hydrogen fuel injection method (diesel engine) induces air during the intake stroke and injects hydrogen gas directly into the cylinder during the compression stroke. Fundamentally, because hydrogen gas does not exist in the intake pipe, backfire, which is the most significant challenge to increasing the torque of the hydrogen port fuel injection engine, does not occur. In this study, using the gasoline fuel injector of a gasoline direct-injection engine for passenger vehicles, hydrogen fuel was injected at high pressures of 5 MPa and 7 MPa into the cylinder, and the effects of the fuel injection timing, including the injection pressure on the output performance and efficiency of the engine, were investigated. Strategies for maximizing engine output performance were analyzed.The fuel injection timing was retarded from before top dead center (BTDC) 350 crank angle degrees (CAD) toward top dead center (TDC). The minimum increase in the best torque ignition timing improved, and the efficiency and excess air ratio increased, resulting in an increase in torque and decrease in NO_x emissions. However, the retardation of the fuel injection timing is limited by an increase in the in-cylinder pressure. By increasing the fuel injection pressure, the torque performance can be improved by further retarding the fuel injection timing or increasing the fuel injection period. The maximum torque of 142.7 Nm is achieved when burning under rich conditions at the stoichiometric air-fuel ratio.     

Influence of injection timing on the exhaust emissions of a dual-fuel CI engine

Environmental concerns and limited amount of petroleum fuels have caused interests in the development of alternative fuels for internal combustion (IC) engines. As an alternative, biodegradable, and renewable fuel, ethanol is receiving increasing attention. Therefore, in this study, influence of injection timing on the exhaust emission of a single cylinder, four stroke, direct injection, naturally aspirated diesel engine has been experimentally investigated using ethanol blended diesel fuel from 0% to 15% with an increment of 5%. The engine has an original injection timing 27° CA BTDC. The tests were performed at five different injection timings (21°, 24°, 27°, 30°, and 33° CA BTDC) by changing the thickness of advance shim. The experimental test results showed that NO_x and CO₂ emissions increased as CO and HC emissions decreased with increasing amount of ethanol in the fuel mixture. When compared to the results of original injection timing, at the retarded injection timings (21° and 24° CA BTDC), NO_x and CO₂ emissions increased, and unburned HC and CO emissions decreased for all test conditions. On the other hand, with the advanced injection timings (30° and 33° CA BTDC), HC and CO emissions diminished, and NO_x and CO₂ emissions boosted for all test conditions.     

Effects of second hydrogen direct injection proportion and injection timing on combustion and emission characteristics of hydrogen/n-butanol combined injection engine

Hydrogen and n-butanol are superior alternative fuels for SI engines, which show high potential in improving the combustion and emission characteristics of internal combustion engines. However, both still have disadvantages when applied individually. N-butanol fuel has poor evaporative atomization properties and high latent heat of vaporization. Burning n-butanol fuel alone can lead to incomplete combustion and lower temperature in the cylinder. Hydrogen is not easily stored and transported, and the engine is prone to backfire or detonation only using hydrogen. Therefore, this paper investigates the effects of hydrogen direct injection strategies on the combustion and emission characteristics of n-butanol/hydrogen dual-fuel engines based on n-butanol port injection/split hydrogen direct injection mode and the synergistic optimization of their characteristics. The energy of hydrogen is 20% of the total energy of the fuel in the cylinder. The experimental results show that a balance between dynamics and emission characteristics can be found using split hydrogen direct injection. Compared with the second hydrogen injection proportion (IP2) = 0, the split hydrogen direct injection can promote the formation of a stable flame kernel, shorten the flame development period and rapid combustion period, and reduce the cyclic variation. When the IP2 is 25%, 50% and 75%, the engine torque increases by 0.14%, 1.50% and 3.00% and the maximum in-cylinder pressure increases by 1.9%, 2.3% and 0.6% respectively. Compared with IP2 = 100%, HC emissions are reduced by 7.8%, 15.4% and 24.7% and NOx emissions are reduced by 16.4%, 13.8% and 7.9% respectively, when the IP2 is 25%, 50% and 75%. As second hydrogen injection timing (IT2) is advanced, CA0-10 and CA10-90 show a decreasing and then increasing trend. The maximum in-cylinder pressure rises and falls, and the engine torque gradually decreases. The CO emissions show a trend of decreasing and remaining constant. However, the trends of HC emissions and NOx emissions with IT2 are not consistent at different IP2. Considering the engine's dynamics and emission characteristics, the first hydrogen injection proportion (IP1) = 25% plus first hydrogen injection timing (IT1) = 240°CA BTDC combined with IP2 = 75% plus IT2 = 105°CA BTDC is the superior split hydrogen direct injection strategy.     

Influence of hydrogen injection timing and duration on the combustion and emission characteristics of a diesel engine operating on dual fuel mode using biodiesel of dairy scum oil and producer gas

The main aim of the present work is to investigate the influence of hydrogen injection timing and injection duration on the combustion and emissions of a CI engine functioning on dual fuel (DF) mode by employing diesel/dairy scum oil methyl ester (DiSOME)/Waste frying oil methyl ester (WFOME) - producer gas (PG) combination. Hydrogen flow rate was maintained constant (8 lpm) and injected in air-producer gas (PG) mixture an inlet manifold using a gas injector. In this current work, injection timing was varied from TDC to 15 deg., aTDC in steps of 5. Similarly, injection duration was adopted from 30 deg., CA to 90 deg., CA and differed in steps of 30. From the outcome of work, it is noticed that the best possible injection timing and injection duration were found to be 10 deg., aTDC and 60 deg., CA respectively. Results showed that, at optimum injection parameters, diesel-PG combination with hydrogen resulted in augmented BTE by 6.7% and 12.4%, decreased smoke by 26.04% and 36.4%, decreased HC by 16.6% and 22.4%, decreased CO by 23.5% and 29.6% and increased NOx by 12.4% and 22.1%, compared to DiSOME and WFOME supported DF operation. Investigation with DiSOME-hydrogen enriched PG combustion showed satisfactory operation.     

Study on combustion and emission characteristics of a n-butanol engine with hydrogen direct injection under lean burn conditions

The n-butanol fuel, as a renewable and clean biofuel, could ease the energy crisis and decrease the harmful emissions. As another clean and renewable energy, hydrogen properly offset the high HC emissions and the insufficient of dynamic property of pure n-butanol fuel in SI engines, because of the high diffusion coefficient, high adiabatic flame velocity and low heat value. Hydrogen direct injection not only avoids backfire and lower intake efficiency but also promotes to form in-cylinder stratified mixture, which is helpful to enhance combustion and reduce emissions. This experimental study focused on the combustion and emissions characteristics of a hydrogen direct injection stratified n-butanol engine. Three different hydrogen addition fractions (0%, 2.5%, 5%) were used under five different spark timing (10° ,15° ,20° ,25° ,30° CA BTDC). Engine speed and excess air ratio stabled at 1500 rpm and 1.2 respectively. The direct injection timing of the hydrogen was optimized to form a beter stratified mixture. The obtained results demonstrated that brake power and brake thermal efficiency are increased by addition hydrogen directly injected. The BSFC is decreased with the addition of hydrogen. The peak cylinder pressure and the instantaneous heat release rate raises with the increase of the hydrogen addition fraction. In addition, the HC and CO emissions drop while the NOx emissions sharply rise with the addition of hydrogen. As a whole, with hydrogen direct injection, the power and fuel economy performance of n-butanol engine are markedly improved, harmful emissions are partly decreased.     

Comparison between blended mode and fumigation mode on combustion,performance and emissions of a diesel engine fueled with ternary fuel (diesel-biodiesel-ethanol) based on engine speed

According to the literature, there is in lack of a comprehensive study to compare the combustion, performance and emissions of a diesel engine using diesel, biodiesel and ethanol fuels (DBE) in the blended mode and fumigation mode under various engine speeds. This study was conducted to fill this knowledge gap by comparing the effect of blended, fumigation and combined fumigation + blended (F + B) modes on the combustion, performance and emissions of a diesel engine under a constant engine load (50% of full torque) with five engine speeds ranging from 1400 rpm to 2200 rpm. A constant overall fuel composition of 80% diesel, 5% biodiesel and 15% ethanol, by volume % (D80B5E15), was utilized to provide the same fuel for comparing the three fueling modes.According to the average results of five engine speeds, the blended mode has higher peak heat release rate (HRR), ignition delay (ID), brake thermal efficiency (BTE), brake specific nitrogen monoxide (BSNO) and brake specific nitrogen oxides (BSNO_X), but lower duration of combustion (DOC), brake specific fuel consumption (BSFC), brake specific carbon dioxide (BSCO₂), brake specific carbon monoxide (BSCO), brake specific hydrocarbon (BSHC), brake specific nitrogen dioxide (BSNO₂), brake specific particulate matter (BSPM), total number concentration (TNC) and geometric mean diameter (GMD), and similar peak in-cylinder pressure compared to the fumigation mode. In addition, for almost all the parameters, results obtained in the F + B mode are in between those of the blended and fumigation modes. In regard to the effect of engine speed, the results reveal that the increase in engine speed causes reduction in peak in-cylinder pressure, BTE, BSHC, BSNO_X, BSNO and BSNO₂, but increase in peak HRR, ID, DOC, BSFC, BSCO₂, BSPM and TNC, and similar BSCO and GMD for almost all the tested fueling modes. It can be inferred that the blended mode is the suitable fueling mode, compared with the fumigation mode, under the operating conditions investigated in this study.     

Performance and emission characteristics of a diesel engine using isobutanol–diesel fuel blends

The aim of this study is to investigate the suitability of isobutanol–diesel fuel blends as an alternative fuel for the diesel engine, and experimentally determine their effects on the engine performance and exhaust emissions, namely break power, break specific fuel consumption (BSFC), break thermal efficiency (BTE) and emissions of CO, HC and NO_x. For this purpose, four different isobutanol–diesel fuel blends containing 5, 10, 15 and 20% isobutanol were prepared in volume basis and tested in a naturally aspirated four stroke direct injection diesel engine at full -load conditions at the speeds between 1200 and 2800 rpm with intervals of 200 rpm. The results obtained with the blends were compared to those with the diesel fuel as baseline. The test results indicate that the break power slightly decreases with the blends containing up to 10% isobutanol, whereas it significantly decreases with the blends containing 15 and 20% isobutanol. There is an increase in the BSFC in proportional to the isobutanol content in the blends. Although diesel fuel yields the highest BTE, the blend containing 10% isobutanol results in a slight improvement in BTE at high engine speeds. The results also reveal that, compared to diesel fuel, CO and NO_x emissions decrease with the use of the blends, while HC emissions increase considerably.     

Influence of injection timing on performance,combustion and emission characteristics of Jatropha biodiesel engine

The study of effect of injection timing along with engine operating parameters in Jatropha biodiesel engine is important as they significantly affect its performance and emissions. The present paper focuses on the experimental investigation of the influence of injection timing, load torque and engine speed on the performance, combustion and emission characteristics of Jatropha biodiesel engine. For this purpose, the experiments were conducted using full factorial design consisting of (3³) with 27 runs for each fuel, diesel and Jatropha biodiesel. The effect of variation of above three parameters on brake specific fuel consumption (BSFC), brake thermal efficiency (BTE), peak cylinder pressure (P_max), maximum heat release rate (HRR_max), CO, HC, NO emissions and smoke density were investigated. It has been observed that advance in injection timing from factory settings caused reduction in BSFC, CO, HC and smoke levels and increase in BTE, P_max, HRR_max and NO emission with Jatropha biodiesel operation. However, retarded injection timing caused effects in the other way. At 15 N m load torque, 1800 rpm engine speed and 340 crank angle degree (CAD) injection timing, the percentage reduction in BSFC, CO, HC and smoke levels were 5.1%, 2.5%, 1.2% and 1.5% respectively. Similarly the percentage increase in BTE, P_max, HRR_max and NO emission at this injection timing, load and speed were 5.3%, 1.8%, 26% and 20% respectively. The best injection timing for Jatropha biodiesel operation with minimum BSFC, CO, HC and smoke and with maximum BTE, P_max, HRR_max is found to be 340 CAD. Nevertheless, minimum NO emission yielded an optimum injection timing of 350 CAD.     

Numerical investigation and Pareto optimization on performance,emission and in-cylinder reforming characteristics for two cylinder reciprocating engine with COx free fuel

The main objective of this study is to introduce the applicability of ammonia to the downsized compression ignition diesel engine for power generation or range extender. For this research objective, the two cylinder engine, which was the result of the previous study, fueled with diesel-ammonia blends was considered and the performance and NOx emission tendency were identified using the numerical method. Ammonia was mixed with diesel via injection at a specific fuel energy fraction (0%, 5%, 10%, or 15%) to evaluate the engine performance and emission characteristics. In addition, concept of “in-cylinder reforming” was introduced adopting negative valve overlap (NVO) by advancing the exhaust valve closing time to investigate the effect of adding ammonia as a hydrogen carrier. Subsequently, the primary variables affecting the brake-specific fuel consumption and NO_X are determined via multi-objective Pareto analysis. The optimal Pareto front confirms that exhaust valve timing exerts a greater effect on the performance and emissions than injection timing. Moreover, in-cylinder reformed hydrogen was increased under negative valve overlap strategy.     

不同喷油提前角对缸内碳烟生成影响的计算与分析

应用计算流体动力学对某小型高速增压直喷式柴油机缸内燃烧过程进行了数值计算,得出了不同喷油提前角下增压直喷式柴油机缸内混合气、温度和碳烟的分布情况,分析了不同喷油提前角下,上止点前后的喷油量的比例对碳烟排放的影响,并通过实际工况下的碳烟排放试验进行了验证。为增压柴油机性能与排放优化提供了参考。     

Improvement of fuel economy of an indirect injection (IDI) diesel engine with two-stage injection

This paper focuses on the effects of early stage injection and two-stage injection on the combustion characteristics and engine performances of an indirect injection (IDI) diesel engine. In a direct injection (DI) diesel engine, HC emission increases with early stage injection because some of the fuel spray adheres to the cylinder wall and burns in the gap between the piston and the cylinder. On the other hand, since the fuel spray of early stage injection in an IDI diesel engine is injected into an auxiliary combustion chamber such as a swirl chamber, the IDI diesel engine could reduced the HC emission produced from the gap compared with a DI diesel engine. In a two-stage injection IDI diesel engine, NO and smoke emissions are improved when the amount of fuel in the first stage injection is small and the first stage injection timing is advanced over −80° TDC. And 20% improvement in fuel consumption is achieved when the first stage injection timing is advanced over −80° TDC. Conversely, HC and CO emissions of two-stage injection increases compared with that of conventional injection of an IDI diesel engine. However, CO emission can be improved a little when the first stage injection timing is advanced over −100° TDC and the second stage injection timing is retarded over TDC.     

The effect of hydrogen on the performance and emissions of an SI engine having a high compression ratio fuelled by compressed natural gas

The aim of this paper is investigation of the effect of hydrogen on engine performance and emissions characteristics of an SI engine, having a high compression ratio, fuelled by HCNG (hydrogen enriched compressed natural gas) blend. The experiments were carried out at 1500, 2000 and 2500 rpm under full load conditions of a modified Isuzu 3.9 L engine, having a compression ratio of 12.5. The engine brake power, brake thermal efficiency, combustion analysis and emissions parameters were realized at 5, 10 15 and 20 deg. CA BTDC (crank angle before top dead center) ignition timings and in excess air ratios of 0.9–1.3 fuelled by hydrogen enriched compressed natural gas (100/0, 95/5, 90/10 and 80/20 of % natural gas/hydrogen).The experimental results showed that the maximum power values were generally obtained with HCNG5 (5% hydrogen in natural gas) fuel. The optimum ignition timing that was obtained according to the maximum brake torque was retarded by the addition of hydrogen to CNG (compressed natural gas), while it was advanced by increasing the engine speed. Furthermore, it was observed that the BTE (brake thermal efficiency) generally declined with the hydrogen addition to compressed natural gas and increasing the engine speed. Additionally, the curves of cylinder pressure and ROHR (rate of heat release values) generally closed to top dead center with the increasing of the hydrogen fraction in the blend and a decreasing engine speed. The hydrocarbon and carbon monoxide emissions generally obtained were lower than the Euro-5 and Euro-6 standards.     

Effect of manifold injection of hydrogen gas in producer gas and neem biodiesel fueled CRDI dual fuel engine

The high flammability of hydrogen gas gives it a steady flow without throttling in engines while operating. Such engines also include different induction/injection methods. Hydrogen fuels are encouraging fuel for applications of diesel engines in dual fuel mode operation. Engines operating with dual fuel can replace pilot injection of liquid fuel with gaseous fuels, significantly being eco-friendly. Lower particulate matter (PM) and nitrogen oxides (NO_x) emissions are the significant advantages of operating with dual fuel.Consequently, fuels used in the present work are renewable and can generate power for different applications. Hydrogen being gaseous fuel acts as an alternative and shows fascinating use along with diesel to operate the engines with lower emissions. Such engines can also be operated either by injection or induction on compression of gaseous fuels for combustion by initiating with the pilot amount of biodiesel. Present work highlights the experimental investigation conducted on dual fuel mode operation of diesel engine using Neem Oil Methyl Ester (NeOME) and producer gas with enriched hydrogen gas combination. Experiments were performed at four different manifold hydrogen gas injection timings of TDC, 5°aTDC, 10°aTDC and 15°aTDC and three injection durations of 30°CA, 60°CA, and 90°CA. Compared to baseline operation, improvement in engine performance was evaluated in combustion and its emission characteristics. Current experimental investigations revealed that the 10°aTDC hydrogen manifold injection with 60°CA injection duration showed better performance. The BTE of diesel + PG and NeOME + PG operation was found to be 28% and 23%, respectively, and the emissions level were reduced to 25.4%, 14.6%, 54.6%, and 26.8% for CO, HC, smoke, and NO_x, respectively.