Ni supported on MgO modified attapulgite as catalysts for hydrogen production from glycerol steam reforming

A series of Mg-modified Ni/Attapulgite (ATP) catalysts have been prepared by impregnation method for glycerol steam reforming to produce hydrogen. The physicochemical properties of catalysts were characterized using various techniques including N₂ physical adsorption analysis, XRD, H₂-TPR, SEM, TEM and NH₃-TPD. The results of N₂ physical adsorption indicated MgO modified Ni-based catalysts had unique mesostructure, resulting in the high metal dispersion and interaction between active metal and support as proven by XRD, TEM and H₂-TPR. Results of glycerin reforming experiments showed that Ni/10MgO/ATP catalyst had the highest activity than that of the other catalysts. Ni/10MgO/ATP catalyst had the smallest Ni average crystal size (10.1 nm) and the highest surface area (110.31 m²/g). These excellent properties made it show the enhanced glycerol conversion (94.71%) and a higher H₂ yield (88.45%) and the longest stability (30 h) during glycerol steam reforming (GSR) at 600 °C, W/G = 3, and WHSV = 1 h^?1. The used catalysts after 60 h of glycerin reforming experiments were also investigated by XRD, SEM, TEM, Roman and TG-DTG. The results indicated that the addition of Mg significantly inhibited the sintering of nickel grains and the formation of amorphous carbon. Therefore, Ni/10MgO/ATP catalyst increased the activity of the catalyst and extended the life of the catalyst.     

Hydrogen production from acetic acid steam reforming over Ti-modified Ni/Attapulgite catalysts

Steam reforming of bio-oil derived oxygenates is a green and sustainable method for hydrogen production. In this work, hydrogen production from steam reforming of acetic acid (SRAA) was investigated over Ti-modified Ni/Attapulgite (ATP) catalysts that prepared via sequential precipitation technique. The effects of Ti additive, precipitation sequence and Ti-salt precursors (TiCl₄, TiOSO₄) on the structural and physicochemical properties of catalysts were characterized by N₂ adsorption-desorption, XRD, FT-IR, HRTEM, XPS, H₂-TPR and NH₃-TPD. These results indicated that the interaction among Ti species, Ni active metal and ATP enhanced the reduction performance as well as weakened surface acidity of the Ni/ATP catalyst, and also promoted the electron transfer to form Ni^δ? species. Obviously, compared with Ti precursor salts, the precipitation sequences played a key role in determining the surface properties of Ti-modified catalysts. Among them, the Ni–Ti_S/ATP catalyst synthesized by co-precipitation method exhibited better reducibility and lower surface acidity, as well as produced more Ni^δ? species and Ni^δ?-O_v-Ti³⁺ interface sites. Then the synergistic effects among the above-mentioned characters made the Ni–Ti_S/ATP catalyst present highest carbon conversion (93.4%) and H₂ yield (77.6%) during SRAA reactions. The analyses of XRD, HRTEM and TG were implemented on used catalysts and discovered Ni–Ti_S/ATP catalysts shown promising metal sintering and coke resistance, which mainly caused by the presence of flat Ni–Ti@ATP structures. The possible conversion mechanism of acetic acid in the flat Ni–Ti@ATP structure of co-precipitation Ti-modified catalyst was also elucidated.     

Zirconia supported nickel catalysts for glycerol steam reforming: Effect of zirconia structure on the catalytic performance

The effect of the zirconia structure in Ni/ZrO₂ catalysts on the glycerol steam reforming (GSR) reaction was studied. A tetragonal zirconia support was synthesized via a hydrolysis technique and loaded with 5 wt% Ni via a wet-impregnation method. Similarly, a commercial monoclinic zirconia support was also impregnated with 5 wt% Ni. Following calcination at 600 °C, physico-chemical properties of the prepared catalysts were investigated by X-Ray Diffraction (XRD), H₂-Temperature Programmed Reduction (H₂-TPR) and CO₂-Temperature Programmed Desorption (CO₂-TPD) techniques. The catalysts were then tested in the GSR reaction in the 400–700 °C range with a steam to glycerol molar ratio of 9:1 and a flow rate of 0.025 mL/min. The monoclinic catalyst exhibited a better performance giving higher hydrogen yields and glycerol conversions. This was attributed to an improved reducibility of Ni in this catalyst. Stability tests at 600 °C revealed the deactivation of the tetragonal catalyst during 6 h as a result of the formation of encapsulating coke which blocked active Ni metal sites. The monoclinic catalyst, exhibiting the formation of only filamentous coke, remained relatively stable for 24 h.     

A review on ethanol steam reforming for hydrogen production over Ni/Al2O3 and Ni/CeO2 based catalyst powders

Hydrogen is contemplated as an alternative clean fuel for the future. Ethanol steam reforming (ESR) is a carbon-neutral, sustainable, green hydrogen production method. Low cost Ni/Al₂O₃ and Ni/CeO₂ powder catalysts demonstrate high ESR activity. However, acidic nature of Al₂O₃ and instability of CeO₂ lead to deactivation of the catalysts easily. This article examines the research articles published on the modification of Ni by various noble and non-noble metals and on alteration of the supports by different metal oxides in detail and their effect on ESR all through 2000–2021. The ESR reaction mechanisms on Ni/Al₂O₃ and Ni/CeO₂ powder catalysts and basic thermodynamics for different possible reactions and H₂ yield are explored. Manipulation of catalyst morphology (surface area and particle size) via preparation method, selection of active metal promoter and support modifier are found to be significantly important for H₂ production and minimizing carbon deposition on catalysts.     

Effects of attapulgite-supported transition metals catalysts on glycerol steam reforming for hydrogen production

The attapulgite supported transition metals (Ni, Cu, Co or Fe) catalysts were prepared by precipitation method at constant loading (10 wt%) and investigated in the glycerol steam reforming reaction for H₂ production under 400–750 °C, water/glycerol (W/G) = 3, N₂ flow ratio = 0.16 L/min and WHSV = 6.46 h^?1. The as-prepared catalysts were characterized by N₂ adsorption-desorption, XRD, H₂-TPR and TEM-EDS. The results shown different active metals presented various crystalline sizes and reduction properties. The experimental results revealed Ni/ATP and Co/ATP catalysts had more active for glycerol steam reforming than Cu/ATP and Fe/ATP catalysts, due to the fact that active metal Ni and Co have superior capacity to promote the necessary CC rupture and facilitate the water gas shift reaction. In addition, the results revealed that CH₄ production was favored at low temperatures while CO production was presented at high temperatures, which were induced by the different reaction networks over catalysts. In addition, the stability test shown all catalysts had different various degrees of inactivation, resulting from the sintering of active metals and carbon deposition. The characterizations of XRD, TEM and TG-DTG for spent catalysts revealed the smallest amount of carbon deposited for Cu/ATP, which was attributed to the lowest Cu particle size. Additionally, two different types of carbon was found, namely filamentous carbon for Ni and Co/ATP and encapsulating carbon for Cu and Fe/ATP.     

Hydrogen production via steam reforming of ethylene glycol over Attapulgite supported nickel catalysts

Steam reforming of ethylene glycol was investigated over Ni-based catalysts supported on Attapulgite (ATP; originating from Jiangsu (JS), Anhui, and Gansu (GS) provinces in China). N₂ adsorption–desorption, XRD, FTIR, H₂-TPR, NH₃-TPD, SEM, and TEM-EDS measurements were performed to analyze the catalyst properties. The results revealed that Ni/ATP_GS had the largest particle size (17.9 nm) and the highest reductive degree (98.0%). Consequently, Ni/ATP_GS showed the highest ethylene glycol conversion (97.2%) during the first 4 h of reaction. However, this catalyst showed the lowest H₂ yield (71.2%), possibly owing to large Ni particle sizes as well as ample surface acidic sites and acidity, leading to a high selectivity toward CH₄ (20.8%) and C₂H₄ (2.2%). In contrast, Ni/ATP_JS presented the highest H₂ yield (89.8%) owing to it having the smallest Ni particle sizes and lowest amount of surface acidic sites. Additionally, this catalyst showed the highest stability over 8 h of reaction. An examination of the spent catalysts revealed that Ni/ATP_JS possessed excellent antisintering and coking properties.     

Glycerol steam reforming on supported Ru-based catalysts for hydrogen production for fuel cells

Glycerol steam reforming on Ru and Ru–Me (Me = Fe, Co, Ni, and Mo) catalysts supported on yttria, ceria–zirconia, and γ-alumina is studied at high temperatures for the production of hydrogen for fuel cell applications. The nature of the support notably affects the catalytic properties of these catalysts resulting in significant enhancements of the H₂ production turnover rate and product selectivity on the reducible yttria and ceria–zirconia supported Ru-based catalysts via facilitation of the water–gas shift reaction. The acidic γ-alumina supported Ru-based catalysts demonstrate a low H₂ production turnover rate with a high CO product selectivity and also favor the formation of C₁–C₂ hydrocarbons. Differently, the promotion effects due to Fe, Co, Ni, and Mo on the bimetallic Ru–Me catalysts are limited with only small increases in the glycerol conversion turnover rate for the Ru–Ni, Ru–Mo, and Ru–Co catalysts. The alumina supported Ru-based catalysts are deactivated by a significant extent with increasing on-stream time due to coking. The carbon deposition is insignificant on the yttria and ceria-zirconia supported catalysts, but moderate deactivation occurs due to sintering of the dispersed metal clusters. Influenced by the surface MoO_x species that hamper sintering of the surface metal clusters and by the Y₂O₃ support that prevents coking on the catalyst, the Ru–Mo/Y₂O₃ catalysts exhibit superior catalytic stability against deactivation.     

Hydrogen production by ethanol steam reforming over M-Ni/sepiolite (M = La,Mg or Ca) catalysts

Ethanol steam reforming (ESR) is a technology of great promise for hydrogen production but designing highly efficient, green and inexpensive Ni-based catalysts for inhibiting metal sinter and carbon deposition and increasing catalyst activity and stability is still a key challenge. In this paper, the M-Ni/Sepiolite catalysts (M-Ni/SEP, M = La, Mg or Ca) were synthesized using a hydrothermal-assisted impregnation method. The results from characterizations such as N₂ adsorption-desorption, XRD, H₂-TPR, XPS, HRTEM and NH₃/CO₂-TPD showed that La, Mg and Ca promoters can facilitate the dispersion and exposure of Ni⁰ active sites, enhance the metal-support interaction and modify surface acid/alkaline sites. Furthermore, the results of catalyst activity tests in ESR demonstrated that the Ca–Ni/SEP catalyst exhibited the highest carbon conversion of 95% and hydrogen yield of 65%, attributed to the small mean Ni particle size, strong metal-support interaction, abundant surface Ni⁰ active sites and modified surface alkaline/acid sites. According to the carbon deposition analyses, it was observed in Ca–Ni/SEP that the carbon deposition amount was evidently decreased, and the graphitic degree of coke was increased due to the increased metal site amount.     

Hydrogen production by steam reforming of acetic acid: Comparison of conventional supported metal catalysts and metal-incorporated mesoporous smectite-like catalysts

The activities of various metal catalysts were tested in steam reforming of acetic acid for the production of H₂, using conventional metal oxides and transition metal-incorporated mesoporous smectite-like materials as supports. It has been found that Pt is superior to Ni, Co, and Fe among Al₂O₃ supported catalysts, Al₂O₃ is more effective than ZrO₂ and SiO₂ as support for Pt, Ni incorporated smectite (SM(Ni)) support is more effective than Fe and Co incorporated ones for Pt, and SM(Ni) is also active in the absence of Pt. The total activity for the conversion of acetic acid is in the order of Pt/Al₂O₃ > Pt/SM(Ni) > SM(Ni) but the ability of H₂ production is comparable among these catalysts. These catalysts (and the other ones) were observed to lose their activities during the reforming reactions. The activity of Pt/Al₂O₃ decreased during the whole course of reaction up to 10 h. In contrast, the activity of SM(Ni) also decreased within 2 h but it showed a stable activity in the following stage of reaction. The initial activity of the used Pt/SM(Ni) and SM(Ni) was able to be almost completely restored by thermal treatment with H₂ but less effectively for the used Pt/Al₂O₃. The catalyst deactivation was shown to occur by the formation and deposition of carbon materials on the catalysts (XRD, TEM, thermal analysis). The properties of carbon deposits formed on Pt/Al₂O₃ and SM(Ni) catalysts should be different and this may be responsible for the differences in the extent of deactivation and in the regeneration behavior between the two catalysts.     

Characterization and activity test of commercial Ni/Al2O3, Cu/ZnO/Al2O3 and prepared Ni–Cu/Al2O3 catalysts for hydrogen production from methane and methanol fuels

In this study, methane and methanol steam reforming reactions over commercial Ni/Al₂O₃, commercial Cu/ZnO/Al₂O₃ and prepared Ni–Cu/Al₂O₃ catalysts were investigated. Methane and methanol steam reforming reactions catalysts were characterized using various techniques. The results of characterization showed that Cu particles increase the active particle size of Ni (19.3 nm) in Ni–Cu/Al₂O₃ catalyst with respect to the commercial Ni/Al₂O₃ (17.9). On the other hand, Ni improves Cu dispersion in the same catalyst (1.74%) in comparison with commercial Cu/ZnO/Al₂O₃ (0.21%). A comprehensive comparison between these two fuels is established in terms of reaction conditions, fuel conversion, H₂ selectivity, CO₂ and CO selectivity. The prepared catalyst showed low selectivity for CO in both fuels and it was more selective to H₂, with H₂ selectivities of 99% in methane and 89% in methanol reforming reactions. A significant objective is to develop catalysts which can operate at lower temperatures and resist deactivation. Methanol steam reforming is carried out at a much lower temperature than methane steam reforming in prepared and commercial catalyst (275–325 °C). However, methane steam reforming can be carried out at a relatively low temperature on Ni–Cu catalyst (600–650 °C) and at higher temperature in commercial methane reforming catalyst (700–800 °C). Commercial Ni/Al₂O₃ catalyst resulted in high coke formation (28.3% loss in mass) compared to prepared Ni–Cu/Al₂O₃ (8.9%) and commercial Cu/ZnO/Al₂O₃ catalysts (3.5%).     

Hydrogen production via the glycerol steam reforming reaction over nickel supported on alumina and lanthana-alumina catalysts

In the present work, a comparative study of Ni catalysts supported on commercially available alumina and lanthana-alumina carriers was undertaken for the glycerol steam reforming reaction (GSR). The supports and/or catalysts were characterized by PZC, BET, ICP, XRD, NH₃-TPD, CO₂-TPD, TPR and SEM. Carbon deposited on the catalytic surface was characterized by SEM, TPO and Raman. Concerning the Ni/LaAl sample it can be concluded that the presence of lanthana by: (a) facilitating the active species dispersion, (b) strengthening the interactions between nickel species and support, (c) increasing of the basic sites' population and redistributing the acid ones in terms of strength and density, provides a catalyst with improved performance for the GSR reaction, in terms of activity, H₂ production and long term stability. TPO and Raman indicate that the carbon on the Ni/LaAl catalyst was mostly amorphous and was deposited mainly on the support surface. For the Ni/Al catalyst, graphitic carbon was prevalent and likely covered its active sites.     

Ni supported on the CaO modified attapulgite as catalysts for hydrogen production from glycerol steam reforming

The Ni catalyst supported on CaO-modified attapulgite (CaO-ATP) were synthesized by wet impregnation method at a constant Ni metal loading (10 wt%). The catalyst was tested by carrying out a glycerin steam reforming reaction under the following conditions: 400–800 °C, W/G is 3, GHSV is 1 h⁻¹. Ni–CaO-ATP exhibited the highest hydrogen yield (85.30%) and glycerol conversion (93.71%) at 600 °C. The catalysts were characterized by N₂ adsorption/desorption, BET, XRD, H₂-TPR, TG and SEM. The results show that ATP has good resistance to carbon deposition. As an attapulgite modifier of Ni–CaO-ATP, CaO promotes the dispersion of the active component nickel species, which would promote the water gas shift reaction, leading to the improving of hydrogen yield. In addition, the addition of Ca would further enhance the inhibition of carbon deposition and prolong the life of the Ni–CaO-ATP catalyst.     

Production of hydrogen via steam reforming of acetic acid over Ni and Co supported on La2O3 catalyst

Nickel (Ni)-cobalt (Co) supported on lanthanum (III) oxide (La₂O₃) catalyst was prepared via impregnation technique to study the steam reformation of acetic acid for hydrogen generation by using one-step fixed bed reactor. Moreover, in order to specify the physical and the chemical attributes of the catalyst, X-ray diffraction (XRD), nitrogen physisorption, temperature-programmed reduction (TPR), temperature-programmed desorption of ammonia and carbon dioxide (TPD-NH₃ and CO₂), scanning electron microscopy (SEM), and thermogravimetric analysis (TGA) methods were employed. The nitrogen physisorption analysis showed that the presence of Co on Ni/La₂O₃ improved the textural properties of the catalyst by increasing the surface area, the pore diameter and the pore volume of the catalyst. This improved the dispersion of metal particle and caused a reduction in the size of metal particle, and consequently, increased the catalytic activity, as well as the resistance to coke formation. On top of that, the condensation and the dehydration reactions during acetic acid steam reforming created carbon deposition on acidic site of the catalyst, which resulted in the deactivation of catalyst and the formation of coke. Besides, in this study, Ni/La₂O₃ contributed to a high acetic acid conversion (100%) at 700 °C, but it produced more coking compared to Ni–Co/La₂O₃ and Co/La₂O₃ catalysts.     

Various nickel doping in commercial Ni–Mo/Al2O3 as catalysts for natural gas decomposition to COx-free hydrogen production

Non-oxidative decomposition of natural gas to CO_x-free hydrogen production over commercial nickel-molybdate hydrotreating catalysts with different Ni loading from 5 to 40wt% were studied at 700 °C. The catalysts were characterized by XRD, BET, TEM, Raman spectroscopy and TG-DTA analysis. The catalytic decomposition activities showed that a tremendous hydrogen production (∼90%) was obtained over 20–40wt%Ni/Mo–Al₂O₃ catalysts. Moreover, all catalysts exhibited excellent durability up to 9 h with stable catalytic activity toward H₂ production. Although the increase of Ni content reduces the catalyst surface area, the H₂ productivity and longevity increases with increased Ni content, i.e., the catalytic decomposition activity primarily depends on the active Ni sites which overcompensates the surface deficiencies. TEM, TGA and XRD data of used catalysts indicated that a higher thermal stability and graphitization degree of multi-walled carbon nanotubes were obtained on all Ni containing catalysts. Higher metal loading produced carbon nanofibers beside CNTs due to increment of particle size and long reaction time.     

Ni/Al2O3 catalysts for CO2 methanation: Effect of silica and nickel loading

Samples containing from 1 to 33 wt.% of NiO on silica and alumina doped with silica (1 and 20 wt.% silica in the support) have been prepared and characterized by BET, XRD, FT-IR, UV–vis–NIR, FE-SEM, EDXS, and TPR techniques. Catalysts have been pre-reduced in situ before catalytic experiments and data have been compared with Ni/Al₂O₃ reference sample. Characterization results showed that SiO₂ support has a low Ni dispersion ability mainly producing segregated NiO particles and a small amount of dispersed Ni²⁺ in exchange sites. Instead, for the Si-doped alumina a “surface spinel monolayer phase” is formed by increasing Ni loading and, only when the support surface is completely covered by this layer, NiO is formed. Moreover, H₂-TPR results indicated that NiO particles are more easily reduced compared to Ni species. Low loading Ni/SiO₂ catalysts show high selectivity and moderate activity for RWGS (reverse Water Gas Shift) reaction, likely mainly due to nickel species dispersed in silica exchange sites, as evidenced by visible spectroscopy. High loading Ni/SiO₂ catalysts show both methanation and RWGS but evident short-term deactivation for methanation, attributed to large, segregated Ni metal particles, covered by a carbon veil. Ni on alumina -rich carriers, where nickel disperses forming a surface spinel phase, show high activity and selectivity for methanation, and short-term catalyst stability as well. This activity is attributed to small nickel clusters or metal particles interacting with alumina, formed upon reaction. The addition of SiO₂ in Al₂O₃ support decreases the activity of Ni catalysts in CO₂ methanation, because it reduces the ability of the support to disperse nickel in form of the surface spinel phase, thus reducing the amount of Ni clusters in the reduced catalysts.     

Highly active Nd-promoted Ni@Al2O3 core-shell catalyst for steam reforming of acetic acid: Insights of the remarkable coke resistance

Aiming at enhancing the coke resistance of Ni-based catalysts, the Nd-doped Ni@A₂O₃ core-shell catalysts were prepared and their catalytic performance was evaluated in the steam reforming of acetic acid (SRAA). The catalysts were characterized by BET, XRD, XRF, HRTEM, H₂-TPR, NH₃-TPD, and DTG. The catalytic performance was greatly enhanced by the incorporation of Nd, with decreased yields of CO, CH₄, and acetone, increased yield of CO₂, and remarkable carbon resistance. The decoking behavior of the spent catalyst was elucidated by H₂O¹⁸-TSD. A low reaction temperature facilitates the formation of amorphous carbon, leading to catalyst deactivation. The decoking ability of the catalyst is greatly improved by the Nd incorporation but is also catalyzed by the exposed Ni surface. The Ni0.01Nd@Al catalyst greatly balanced the exposed Ni surface and the mobile lattice oxygen, showing the highest catalytic activity, lowest coke deposition, and superb decoking ability.     

H2 production by methane decomposition: Catalytic and technological aspects

Ni and Co supported on SiO₂ and Al₂O₃ silica cloth thin layer catalysts have been investigated in the catalytic decomposition of natural gas (CDNG) reaction. The influence of carrier nature and reaction temperature was evaluated with the aim to individuate the key factors affecting coke formation. Both Ni and Co silica supported catalysts, due to the low metal support interaction (MSI), promotes the formation of carbon filament with particles at tip. On the contrary, in case alumina was used as support, metals strongly interact with surface thus depressing both the metal sintering and the detachment of particles from catalyst surface. In such cases, carbon grows on metal particle with a “base mechanism” while particles remain well anchored on the catalyst surface. This allowed to realize a cyclic dual-step process based on methane decomposition and catalyst oxygen regeneration without deactivation of catalyst. Technological considerations have led to conclude that the implement of a process based on decomposition and regeneration of catalyst by oxidation requires the development of a robust catalytic system characterized by both a strong MSI and a well defined particle size distribution. In particular, the catalyst should be able to operate at high temperature, necessary to reach high methane conversion values (> 90%), avoiding at the same time the formation of both the carbon filaments with metal at tip or the encapsulating carbon which drastically deactivate the catalyst.     

Effect of impurities of CH3OH,CH3COOH,and KOH on aqueous phase reforming of glycerol over mesoporous Ni–Cu/CeO2 catalyst

Impurities are inevitable in crude glycerol, a by-product of biodiesel, which has a great influence on aqueous phase reforming (APR). This work investigates three impurities (CH₃OH, CH₃COOH, and KOH) in the aqueous phase reforming of glycerol (GAPR) using a mesoporous Ni–Cu/CeO₂ catalyst at three temperatures. The experiment results indicate that the increase of temperature is beneficial to the conversion of glycerol into gas products, but not favor to the proportion of H₂ in the gas phase. The presence of CH₃OH almost has not affected the total gas volume, while CH₃COOH and KOH decreased and increased the gas volume, respectively. The deactivation of the catalyst occurs under acidic conditions because the active phase Ni on the catalyst surface is lost in the hydrogen evolution reaction. KOH has the greatest influence on the gas phase composition, which greatly increases the H₂ production and the proportion of H₂. The results of liquid-phase solution analysis show that the addition of CH₃COOH promoted the dehydration of glycerol, which is contrary to the results obtained by adding KOH. CH₃OH, as the final product of glycerol dehydrogenation and decarbonization, is added to the initial solution, which will be conducive to the dehydration reaction. The addition of CaO can increase the H₂ production in the APR of glycerol solution containing impurities.     

EDTA impregnation assisted synthesis of nickel nanoparticles embedded in activated carbon and its application for dry reforming of methane

In this paper, the catalysts with nanoscale nickel particles embedded in activated carbon were synthesized by Ethylenediaminetetraacetic acid (EDTA) assisted impregnation method. The experimental results revealed that EDTA addition could promote Ni particle dispersion and decrease Ni particle size. Ni particle size was significantly decreased from 18.23 to 4.57 nm when Ni/EDTA ratio was increased from 1:0 to 1:3. Catalytic performance of Ni₁₅-AC-E₃ demonstrated that CH₄ and CO₂ conversion rate under 850 °C were 90.05% and 96.28%, which were decreased by 1.08% and 1.27% after 72 h dry reforming methane (DRM) reaction. Moreover, the characteristic of the used catalyst showed that Ni particle size was only increased from 4.57 to 5.94 nm after the stability test, and NiO was not appeared. Meanwhile, the deposited carbon in the used catalyst was 5.02%. The above results meant that the catalyst prepared by EDTA assisted impregnation method had the ability of suppressing carbon deposition, Ni particle sintering and oxidation during DRM reaction.     

Effect of lithium carbonate on nickel catalysts for direct internal reforming MCFC

Despite many advantages of the direct internal reforming molten carbonate fuel cell (DIR-MCFC) in producing electricity, there are many problems to solve before practical use. The deactivation of reforming catalyst by alkali like lithium is one of the major obstacles to overcome. A promising method is addition of TiO₂ into the Ni/MgO reforming catalyst, which resulted in the increased resistance to lithium poisoning as we previously reported. To understand how added titania worked, it is necessary to elucidate the deactivation mechanism of the catalysts supported on metal oxides such as MgO and MgO–TiO₂ composite oxide.Several supported nickel catalysts deactivated by lithium carbonate were prepared, characterized and evaluated. The Ni/MgO catalyst turned out to be most vulnerable to lithium deactivation among the employed catalysts. The activity of the Ni/MgO gradually decreased to zero with increasing amount of lithium addition. Deactivation by lithium addition resulted from the decrease of active site due to sintering of nickel particles as well as the formation of the Li_yNi_xMg_1−x−yO ternary solid solution. These were evidenced by H₂ chemisorption, temperature programmed reduction, and XRD analyses. As an effort to minimize Li-poisoning, titanium was introduced to MgO support. This resulted in the formation of Ni/Mg₂TiO₄, which seemed to increase resistance against Li-poisoning.