Performance and combustion characteristic of CI engine fueled with hydrogen enriched diesel

The combustion of hydrogen–diesel blend fuel was investigated under simulated direct injection (DI) diesel engine conditions. The investigation presented in this paper concerns numerical analysis of neat diesel combustion mode and hydrogen enriched diesel combustion in a compression ignition (CI) engine. The parameters varied in this simulation included: H₂/diesel blend fuel ratio, engine speed, and air/fuel ratio. The study on the simultaneous combustion of hydrogen and diesel fuel was conducted with various hydrogen doses in the range from 0.05% to 50% (by volume) for different engine speed from 1000 – 4000 rpm and air/fuel ratios (A/F) varies from 10 – 80. The results show that, applying hydrogen as an extra fuel, which can be added to diesel fuel in the (CI) engine results in improved engine performance and reduce emissions compared to the case of neat diesel operation because this measure approaches the combustion process to constant volume. Moreover, small amounts of hydrogen when added to a diesel engine shorten the diesel ignition lag and, in this way, decrease the rate of pressure rise which provides better conditions for soft run of the engine. Comparative results are given for various hydrogen/diesel ratio, engine speeds and loads for conventional Diesel and dual fuel operation, revealing the effect of dual fuel combustion on engine performance and exhaust emissions.     

Experimental investigations on the effect of fuel injection parameters on diesel engine fuelled with biodiesel blend in diesel with hydrogen enrichment

Fuel injection pressure and injection timing are two extensive injection parameters that affect engine performance, combustion, and emissions. This study aims to improve the performance, combustion, and emissions characteristics of a diesel engine by using karanja biodiesel with a flow rate of 10 L per minute (lpm) of enriched hydrogen. In addition, the research mainly focused on the use of biodiesel with hydrogen as an alternative to diesel fuel, which is in rapidly declining demand. The experiments were carried out at a constant speed of 1500 rpm on a single-cylinder, four-stroke, direct injection diesel engine. The experiments are carried out with variable fuel injection pressure of 220, 240, and 260 bar, and injection timings of 21, 23, and 25 °CA before top dead center (bTDC). Results show that karanja biodiesel with enriched hydrogen (KB20H10) increases BTE by 4% than diesel fuel at 240 bar injection pressure and 23° CA bTDC injection timing. For blend KB20H10, the emissions of UHC, CO, and smoke opacity are 33%, 16%, and 28.7% lower than for diesel. On the other hand NOx emissions, rises by 10.3%. The optimal injection parameters for blend KB20H10 were found to be 240 bar injection pressure and 23 °CA bTDC injection timing based on the significant improvement in performance, combustion, and reduction in exhaust emissions.     

Effect of natural gas enrichment with hydrogen on combustion process and emission characteristic of a dual fuel diesel engine

The paper presents results of experimental research on a dual-fuel engine powered by diesel fuel and natural gas enriched with hydrogen. The authors attempted to replace CNG with hydrogen fuel as much as possible with a constant dose of diesel fuel of 10% of energy fraction. The tests were carried out for constant engine load of IMEP = 0.7 MPa and a rotational speed of n = 1500 rpm. The effect of hydrogen on combustion, heat release, combustion stability and exhaust emissions was analyzed. In the test engine, the limit of hydrogen energy fraction was 19%. The increase in the fraction caused an increase in the cycle-by-cycle variation and the occurrence of engine knocking. It was shown that the enrichment of CNG with hydrogen allows for the improvement in the combustion process compared to the co-combustion of diesel fuel with non-enriched CNG, where the reduction in the duration of combustion by 30% and shortening the time of achieving 50% of MFB by 50% were obtained. The evaluation of the spread of the end of combustion is also presented. For H₂ energetic share over 20%, the spread of end of combustion was 48° of crank angle. Measurement of exhaust emissions during the tests revealed an increase in THC and NO_x emissions.     

Performance, emission and combustion characteristics of biodiesel fuelled variable compression ratio engine

Experiments has been carried out to estimate the performance, emission and combustion characteristics of a single cylinder; four stroke variable compression ratio multi fuel engine fuelled with waste cooking oil methyl ester and its blends with standard diesel. Tests has been conducted using the fuel blends of 20%, 40%, 60% and 80% biodiesel with standard diesel, with an engine speed of 1500 rpm, fixed compression ratio 21 and at different loading conditions. The performance parameters elucidated includes brake thermal efficiency, specific fuel consumption, brake power, indicated mean effective pressure, mechanical efficiency and exhaust gas temperature. The exhaust gas emission is found to contain carbon monoxide, hydrocarbon, nitrogen oxides and carbon dioxide. The results of the experiment has been compared and analyzed with standard diesel and it confirms considerable improvement in the performance parameters as well as exhaust emissions. The blends when used as fuel results in the reduction of carbon monoxide, hydrocarbon, carbon dioxide at the expense of nitrogen oxides emissions. It has found that the combustion characteristics of waste cooking oil methyl ester and its diesel blends closely followed those of standard diesel.     

Study of the oxidation stability and exhaust emission analysis of Moringa olifera biodiesel in a multi-cylinder diesel engine with aromatic amine antioxidants

In this study, the two most effective aromatic amine antioxidants N,N′-diphenyl-1,4-phenylenediamine (DPPD) and N-phenyl-1,4-phenylenediamine (NPPD), were used at a concentration of 2000 ppm. The impact of antioxidants on the oxidation stability, exhaust emission and engine performance of a multi-cylinder diesel engine fuelled with MB20 (20% Moringa oil methyl ester and 80% diesel fuel blend) were analysed at varying speed conditions at an interval of 500 rpm and a constant load. It was observed that, blending with diesel enhanced the oxidation stability of the moringa biodiesel by approximately 6.97 h, and the addition of DPPD and NPPD to MB20 increased the oxidation stability up to 34.5 and 18.4 h, respectively. The results also showed that the DPPD- and NPPD-treated blends reduced the NOx emission by 7.4% and 3.04%, respectively, compared to the untreated blend. However, they do have higher carbon monoxide (CO) and hydrocarbon (HC) levels and smoke opacities, but it should be noted that these emissions are still well below the diesel fuel emission level. The results show that the addition of antioxidant with MB20 also improves the engine's performance characteristics. Based on this study, MB20 blends with amine antioxidants can be used in diesel engines without any modification.     

Multi-objective optimization of diesel engine performance,vibration and emission parameters employing blends of biodiesel,hydrogen and cerium oxide nanoparticles with the aid of response surface methodology approach

Recent surges in crude oil prices have motivated researchers to find an alternative sustainable fuel called biodiesel from various inedible oils with lower carbo impact on the environment. The research is performed in diesel engine fuelled with blends of biodiesel coupled with cerium oxide nanoparticles and hydrogen content so as to optimize various factors which are responsible for performance, vibration and emission characteristics. Multi-objective optimization is achieved by employing RSM which also examines prime input parameters (engine load, nanoparticle concentration, compression ratio, hydrogen blend percentage and ignition pressure) responsible in varying engine characteristics. Henceforth, blends of Water Hyacinth can be successfully applied in diesel engine with lower environmental impact and enhanced cost effectiveness. Experimentation is performed on the central composite rotating design (CCRD) matrix with 5-level factor. Engine load was applied between 0 and 100%, NPC varied between 0 and 80 ppm, CR ranges between 17 and 19, hydrogen blend percentage varies between 0 and 40% and at a maximum injection pressure of 240 bar. Pareto-optimal conditions achieved for input conditions of 28.68% biofuel blend, 87.88 engine load, 80 ppm NPC, compression ratio of 19 and 194.54 bar infusion pressure were BTE, BSEC, NOx, UBHC and vibration reduction are 33.57%, 0.2550, 461.3002 ppm vol., and 28.08 ppm vol. And 22.21%, respectively.     

Numerical and experimental investigation of hydrogen enrichment in a dual-fueled CI engine: A detailed combustion,performance, and emission discussion

An effort has been made to simulation a compression ignition engine using hydrogen-diesel, hydrogen-diethyl ether, hydrogen-n-butanol and base diesel fuel as alternatives. The engine measured for the simulation is a single cylinder, four stroke, direct injection, diesel engine. During the simulation the injection timing and engine speed are kept constant at 23°bTDC and 1500 rpm. Diesel-RK, a piece of commercial software employed for this project, can forecast an engine emission, performance and combustion characteristics. The examination of the anticipated outcomes reveals that adding hydrogen to diesel leads in a small increase in efficiency and fuel consumption. With the usage of hydrogen-blend fuels, the majority of dangerous pollutants in exhaust are greatly decreased. The shortest ignition delay was consistently given by 5H295DEE. The lowest CO₂ (578.61 g/kWh) was given by 5H295nB at CR 19.5. Hydrogen blends increase NOx emissions more than base diesel fuel. In the case of smoke and particulate matter emission, the reduce tendency was seen.     

Experimental investigation of SI engine characteristics using Acetone-Butanol-Ethanol (ABE) – Gasoline blends and optimization using Particle Swarm Optimization

This study conducts an experimental investigation of spark ignition (SI) engine characteristics using gasoline blended with Acetone-Butanol-Ethanol (ABE) that act as hydrogen and oxygen carriers. The number of experiments is planned and executed according to a design of experiments with full-factorial design, wherein ABE blend percentage and speed are taken as input parameters and brake thermal efficiency (BTE), emissions of carbon monoxide (CO), hydrocarbon (HC), and oxides of nitrogen (NOx) are taken as the responses. In the present study, a multi-objective optimization technique, Particle Swarm Optimization (PSO), is used to optimize spark ignition engine performance and emission parameters. The results predicted by the regression model are compared with the experimental results. PSO is used to study the Pareto front of BTE, CO, HC, and NOx, respectively. The results indicated that when the engine is run at 1500 rpm, with the fuel blend having 5.4% ethanol, a minimum value of 0.58% CO, 211 ppm of HC are obtained, giving a maximum BTE of 28%. Similarly, when the engine is run at 2264 rpm with a 5% ethanol blend, minimum NOx emission of 1029 ppm and a maximum BTE of 30% are obtained.     

Effect of equivalence ratios on the power,combustion stability and NOx controlling strategy for the turbocharged hydrogen engine at low engine speeds

Increase the equivalence ratio is a good way to improve performance of turbocharged hydrogen engines at low engine speeds. To explore the feasibility of this strategy, this paper investigated the experimental data of a 2.3 L turbocharged port fuel injection (PFI) hydrogen engine at 1500 rpm and 2000 rpm. The results showed that the power can increase from 6.8 kW to 21 kW at 2000 rpm and from 6.4 kW to 16.5 kW at 1500 rpm with increasing of the equivalence ratio. However, the equivalence ratio corroding to the biggest power is 0.8 at 1500 rpm and 0.9 at 2000 rpm because the turbocharged pressure and the volumetric efficiency at 2000 rpm are higher than the ones at 1500 rpm. The biggest BTE can reach to 30.1% at 2000 rpm and 29.3% at 1500 rpm within the range of 0.65–0.8. The covariance of indicated mean effective pressure (CoV_imep) of turbocharged hydrogen is lower than 1.5% at low engine speeds and the combustion stability increased with the increase of equivalence ratio. The NO_x can be reduced from 877 ppm to 0 ppm at 1500 rpm and from 1259 ppm to 17 ppm at 2000 rpm, which means the reduction efficiency of H₂+TWC can exceed 99%.     

Experimental investigations of performance,emission and combustion characteristics of Karanja oil blends fuelled DICI engine

Vegetables oils are simplest route of biofuel utilization in direct injection compression ignition (DICI) engines however several operational and durability problems are encountered while using straight vegetable oils in CI engines due to their high viscosity and low volatility. Reduction of viscosity by blending or exhaust gas heating leads to savings in chemical processing cost incurred on transesterification. In this experimental study, performance, emission and combustion characteristics of Karanja oil blends (K10, K20, K50 and K100) with mineral diesel were investigated in unheated conditions in a direct injection CI engine at different engine loads and constant engine speed (1500 rpm) vis-à-vis baseline data from mineral diesel. Analysis of performance parameters such as brake specific fuel consumption (BSFC), thermal efficiency, and exhaust gas temperature; mass emissions of various gaseous pollutant species; combustion parameters such as in-cylinder pressure rise, instantaneous heat release and cumulative heat release etc. were carried out. Detailed combustion analysis revealed that the combustion duration increased significantly even with smaller concentration of Karanja oil in the fuel blend. HC, CO and Smoke emissions were found to decrease for 20–50% (v/v) Karanja oil content in the fuel blends.     

Emission characteristics of vehicles fueled by hydrogen-enriched syngas under no-load condition

The emission characteristics of vehicles fueled by hydrogen-enriched syngas were investigated under the no-load condition. Syngas was produced using a fixed-bed gasification system. A Jetta car was modified and used for emission experiments with engine speed between 800 and 4800 rpm. Syngas compositions and emissions were analyzed using gas chromatography and a SPX-Tecnotest 488 exhaust gas analyzer, respectively. The results showed that syngas composition had significant effect on HC and NOx emission and air ratio (λ) was the key factor affecting CO emission. HC and NOx emissions increased significantly from 6 to 16 ppm and 139–832 ppm, respectively, when engine speed increased from 800 to 4800 rpm. CO emission did not significantly increase (lower than 0.5%) at engine speed less than 3200 rpm; at higher than 4800 rpm engine speed, CO emission increased rapidly (up to 2.7%).     

Analysis of ignition delay by taking Di-tertiary-butyl peroxide as an additive in a dual fuel diesel engine using hydrogen as a secondary fuel

Ignition delay (ID) is one of the important parameters that make influenced on the combustion process inside the cylinder. This ignition delay affects not only the performances but also the noise and emissions of the engine. In this regards the experiments were conducted on single cylinder 4–stroke compression ignition research diesel engine, power 3.50 kW at constant speed 1500 rpm Kirloskar model TV1 with base fuel as diesel and hydrogen as secondary fuel with and without Di-tertiary-butyl-peroxide (DTBP). Experiments were conducted to measure the ignition delay of the dual fuel diesel (DFD) engine at different load conditions and substitution of diesel by hydrogen with or without DTBP and then it was compared with predicted ID given by Hardenberg-Hase equation and modified Hardenberg-Hase equation.The experimental values of ignition delay were compared with theoretical ignition delay which was predicted on the basis of Hardenberg-Hase equation by considering mean cylinder temperature, pressure, activation energy and cetane number and variations are found in between 6.60% and 21.22%. While, the Hardenberg-Hase equation was modified (by considering variation in activation energy) for DFD engine working on diesel as primary fuel and hydrogen as secondary fuel shows variations 1.20%–11.96%. Furthermore, with DTBP it gives variation up to 18.01%. It was found that ID decreases with increase in percentage of DTBP and hydrogen in air-fuel mixture. This might be due to the cetane improver nature of DTBP, pre-ignition reaction rate and energy release rate of hydrogen fuel. The polytropic index get increased by addition of (Di-tert butyl peroxide) DTBP. Similarly, 5% Di tertiary butyl peroxide reduces Ignition delay.     

Particulate characteristics of laser ignited hydrogen enriched compressed natural gas engine

Laser ignition (LI) is emerging as a strong technology to control the oxides of nitrogen (NOx) emissions from spark ignition (SI) engines without the need for any significant exhaust gas after-treatment and is an appropriate technology for meeting future emission norms in the automotive sector. In this study, particulate characteristics of LI engine fuelled with different compressed natural gas (CNG) and hydrogen mixtures [100% CNG, 10HCNG (10% v/v hydrogen with 90% v/v CNG), 30HCNG (30% v/v hydrogen with 70% v/v CNG), 50HCNG (50% v/v hydrogen with 50% v/v CNG) and 100% hydrogen] were investigated. Experiments were performed in a suitably modified single cylinder engine, which operated in LI mode at constant engine speed (1500 rpm) at five different engine loads (5, 10, 15, 20 and 25 Nm). Particulate characteristics were determined using an engine exhaust particle sizer (EEPS). Results showed that particle number concentration increased with increasing engine load. Number-size, surface area-size and mass-size distributions of particulates reflected that addition of hydrogen in the CNG improved particulate emission characteristics especially in nucleation mode particle (NMP) size range (10 nm < Dp < 50 nm). Among the test fuels, hydrogen-fuelled engine emitted the lowest number of particles. It was observed that the difference between particulate characteristics emitted by different test fuels reduced at higher engine loads. Significant contribution of lubricating oil in particulate emissions from both hydrogen as well as HCNG fuelled LI engine was an important finding of this study. Dominant contribution of larger particles (Dp > 50 nm) in total particle mass (TPM) was an important observation of this study. The qualitative correlation between total particle number (TPN) and TPM indicated that suitable fuel composition at different engine loads yielded cleaner exhaust from the LI engine. Overall, this study demonstrated that addition of hydrogen in CNG is advantageous from particulate reduction point of view, however, optimum fuel composition should be adjusted according to engine operating condition in order to reduce particulate emissions.     

The effect of hydrogen on the performance and emissions of an SI engine having a high compression ratio fuelled by compressed natural gas

The aim of this paper is investigation of the effect of hydrogen on engine performance and emissions characteristics of an SI engine, having a high compression ratio, fuelled by HCNG (hydrogen enriched compressed natural gas) blend. The experiments were carried out at 1500, 2000 and 2500 rpm under full load conditions of a modified Isuzu 3.9 L engine, having a compression ratio of 12.5. The engine brake power, brake thermal efficiency, combustion analysis and emissions parameters were realized at 5, 10 15 and 20 deg. CA BTDC (crank angle before top dead center) ignition timings and in excess air ratios of 0.9–1.3 fuelled by hydrogen enriched compressed natural gas (100/0, 95/5, 90/10 and 80/20 of % natural gas/hydrogen).The experimental results showed that the maximum power values were generally obtained with HCNG5 (5% hydrogen in natural gas) fuel. The optimum ignition timing that was obtained according to the maximum brake torque was retarded by the addition of hydrogen to CNG (compressed natural gas), while it was advanced by increasing the engine speed. Furthermore, it was observed that the BTE (brake thermal efficiency) generally declined with the hydrogen addition to compressed natural gas and increasing the engine speed. Additionally, the curves of cylinder pressure and ROHR (rate of heat release values) generally closed to top dead center with the increasing of the hydrogen fraction in the blend and a decreasing engine speed. The hydrocarbon and carbon monoxide emissions generally obtained were lower than the Euro-5 and Euro-6 standards.     

Investigation of the effects of hydrogen on cylinder pressure in a split-injection diesel engine at heavy EGR

The distinctive properties of hydrogen have initiated considerable applied research related to the internal combustion engine. Recently, it has been reported that NO_x emissions were reduced by using hydrogen in a diesel engine at low temperature and heavy EGR conditions. As the continuing study, cylinder pressure was also investigated to determine the combustion characteristics and their relationship to NO_x emissions. The test engine was operated at constant speed and fixed diesel fuel injection rate (1500 rpm, 2.5 kg/h). Diesel fuel was injected in a split pattern into a 2-L diesel engine. The cylinder pressure was measured for different hydrogen flow rates and EGR ratios. The intake manifold temperature was controlled to be the same to avoid the gas intake temperature variations under the widely differing levels (2%-31%) of EGR. The measured cylinder pressure was analyzed for characteristic combustion values, such as mass burn fraction and combustion duration.The rising crank angle of the heat release rate was unaffected by the presence of hydrogen. However, supplying hydrogen extended the main combustion duration. This longer main combustion duration was particularly noticeable at the heavy EGR condition. It correlated well with the reduced NO_x emissions.     

Flexible syngas-biogas-hydrogen fueling spark-ignition engine behaviors with optimized fuel compositions and control parameters

This paper presents the results research on the optimal fuel compositions and the control parameters of the spark ignition engine fueled with syngas-biogas-hydrogen for the purpose of setting up a flexible electronic control unit for the engine working in a solar-biomass hybrid renewable energy system. In syngas-biogas-hydrogen mixture, the optimal content of hydrogen and biogas is 20% and 30%, respectively. Exceeding these thresholds, the improvement of engine performance is moderate, but the pollution emission increases strongly. The optimal advanced ignition angle is 38°CA, 24°CA, and 18°CA for syngas, biogas, and hydrogen, respectively. With the same content of hydrogen or biogas in the mixture with syngas, the advanced ignition angle of the hydrogen-syngas blend is less than that of the syngas-biogas blend by about 4°CA at the engine speed of 3000 rpm. The derating power of the engine is 30% and 23% as switching from the hydrogen and biogas fueling mode to the syngas fueling mode, respectively. However, NO_x emission of the engine increase from 200 ppm (for syngas) to 2800 ppm (for biogas) and to over 6000 ppm (for hydrogen). The optimal advanced ignition angle, the optimal equivalence ratio of the syngas-biogas-hydrogen fuel mixture vary within the limits of the respective values for syngas and hydrogen. To improve the engine efficiency and reduce pollutant emissions, the loading control system of the engine should prioritize the adjustment of the fuel flow and then the adjustment of the air-fuel mixture flow.     

Effect of hydrogen and ethanol addition in cashew nut shell liquid biodiesel operated direct injection (DI) diesel engine

In this experimental research, the hydrogen gas at a different flow rate (4 lpm, 8 lpm, & 12 lpm) is introduced into the intake port of a diesel engine fueled with B20 (20% CNSL (Cashew nut shell liquid) + 80% diesel) biodiesel blend to find out the best H₂ flow rate. Then, ethanol-blended (5%, 10%, and 15% by volume) B20 blend along with the best H₂ flow rate are tested in the same engine to examine the engine performance. The experimental results showed that B20 with 8 lpm H₂ flow gives the maximum brake thermal efficiency and subsequently reduces the BSFC. Furthermore, by blending ethanol with the B20 blend, the BTE of the engine is improved further. The 10% ethanol blended B20 blend with 8 lpm hydrogen flow gives the maximum BTE of 37.9% higher than diesel whose values are 33.6% at full load. Also, this fuel combination led to the maximum reduced levels of CO and HC emissions with an increase in exhaust gas temperature and NOx emissions. From the results, the 10% ethanol blended B20 blend with 8 lpm H₂ flow dual-fuel configuration is recommended as an alternative to sole diesel fuel.     

The characteristics of waste-cooking palm biodiesel-fueled CRDI diesel engines: Effect hydrogen enrichment and nanoparticle addition

The influence of iron nanoparticle (INP) addition (75 ppm) and hydrogen enrichment (10 lpm) with waste cooking palm biodiesel blend (WCB) on a CRDI diesel engine is evaluated. A blend of 20% WCB and 80% diesel is used, and the dosing level of INP has been kept at 75 ppm, which has been decided based on the oxygen content of biodiesel. Results indicate that the combination of H₂ enrichment and INP addition improves the BTE and BSFC of biodiesel blends as that of diesel. A maximum improvement of BTE of 7.1% than that of diesel is obtained at 90% loading. The combined impact of better hydrogen combustion characteristics and improved air-fuel mixing with nanoparticles reduces CO and HC emissions by 37.5% and 41.8%, respectively, for the WCB fuel sample. However, NO_X emission shows an elevation of 27.4% compared to diesel. Combustion parameters, namely ICP (80.1 bar) and HRR (89.5 J/˚CA) indicate an improvement of 5.3% and 6.7% compared to diesel for WCB + INP + H₂. This is owing to the combination of hydrogen's rapid flame speed and INP-added biodiesel's increased thermal conductivity.     

Research of performance and emission indicators of the compression-ignition engine powered by hydrogen - Diesel mixtures

The purpose of this study is to use the hydrogen – diesel mixture in Audi/VW 1.9 TDI turbocharged CI engine equipped with dynamometer and examine the performance and emission indicators by comparing it with sole diesel mode. The recent diesel emission scandals because of manufacturers cheating the laboratory tests, have initiated the discussions about the sustainable and environmentally friendly diesel engines. The CI engine without major engine modifications was set to operate at two speeds of 1900 rpm and 2500 rpm. At each of speed, the experiment was conducted at three BMEP: 0.4 MPa, 0.6 MPa, and 0.8 MPa. The test engine was operated using diesel fuel with amounts of 10 l/min, 20 l/min, and 30 l/min of hydrogen gas, supplied with air into intake manifold before the turbocharger. Relatively low hydrogen fraction (max. 15.74%) has effect on diesel combustion process and performance indicators at the all range of BMEP. The in-cylinder peak pressure at both speeds of 1900 rpm and 2500 rpm was lower than that with pure diesel fuel, as the small amount of hydrogen shortens the CI engine ignition delay period and decreases the rate of pressure rise. The decrease of BTE noticed, and increase of BSFC was registered with low hydrogen fraction (hydrogen amounts of 10 l/min, 20 l/min). However, with increase of hydrogen amount to 30 l/min, the BTE increased and BSFC decreased to the level, which was lower than that at the pure diesel test. The supply of hydrogen positively effects on engine emissions: the smokiness, NO_x, CO₂, CO decreased, the only hydrocarbon increased. The effect of hydrogen fraction on the combustion and emission characteristics of the diesel - hydrogen mixture was validated by AVL (Anstalt für Verbrennungskraftmaschinen List) BOOST and analysed with presentations of the main limitations and perspectives.     

Performance and emission characteristics of a diesel engine using isobutanol–diesel fuel blends

The aim of this study is to investigate the suitability of isobutanol–diesel fuel blends as an alternative fuel for the diesel engine, and experimentally determine their effects on the engine performance and exhaust emissions, namely break power, break specific fuel consumption (BSFC), break thermal efficiency (BTE) and emissions of CO, HC and NO_x. For this purpose, four different isobutanol–diesel fuel blends containing 5, 10, 15 and 20% isobutanol were prepared in volume basis and tested in a naturally aspirated four stroke direct injection diesel engine at full -load conditions at the speeds between 1200 and 2800 rpm with intervals of 200 rpm. The results obtained with the blends were compared to those with the diesel fuel as baseline. The test results indicate that the break power slightly decreases with the blends containing up to 10% isobutanol, whereas it significantly decreases with the blends containing 15 and 20% isobutanol. There is an increase in the BSFC in proportional to the isobutanol content in the blends. Although diesel fuel yields the highest BTE, the blend containing 10% isobutanol results in a slight improvement in BTE at high engine speeds. The results also reveal that, compared to diesel fuel, CO and NO_x emissions decrease with the use of the blends, while HC emissions increase considerably.