Investigation of a multi-generation system using a hybrid steam biomass gasification for hydrogen, power and heat

In this paper, an integrated process of steam biomass gasification and a solid oxide fuel cell (SOFC) is investigated energetically to evaluate both electrical and energy efficiencies. This system is conceptualized as a combined system, based on steam biomass gasification and with a high temperature, pressurized SOFC. The SOFC system uses hydrogen obtained from steam sawdust gasification. Due to the utilization of the hydrogen content of steam in the reforming and shift reaction stages, the system efficiencies reach appreciable levels. This study essentially investigates the utilization of steam biomass gasification derived hydrogen that was produced from an earlier work in a system combines gasifier and SOFC to perform multi-duties (power and heat). A thermodynamic model is developed to explore a combination of steam biomass gasification, which produces 70–75 g of hydrogen/kg of biomass to fuel a planar SOFC, and generate both heat and power. Furthermore, processes are emerged in the system to increase the hydrogen yield by further processing the rest of gasification products: carbon monoxide, methane, char and tar. The conceptualized scheme combines SOFC operates at 1000 K and 1.2 bar and gasifier scheme based on steam biomass gasification which operates close to the atmospheric pressure, a temperature range of 1023–1423 K and a steam-biomass ratio of 0.8 kmol/kmol. A parametric study is also performed to evaluate the effect of various parameters such as hydrogen yield, air flow rate etc. on the system performance. The results show that SOFC with an efficiency of 50.3% operates in a good fit with the steam biomass gasification module with an efficiency, based on hydrogen yield, of 55.3%, and the overall system then works efficiently with an electric efficiency of ∼82%.     

Continuous hydrogen production by biomass gasification in supercritical water heated by molten salt flow: System development and reactor assessment

Hydrogen production by biomass gasification using solar energy is a promising approach for overcoming the drawbacks of fossil fuel utilization, but the storage of discontinuous solar flux is a critical issue for continuous solar hydrogen production. A continuous hydrogen production system by biomass gasification in supercritical water using molten-salts-stored solar energy was proposed and constructed. A novel double tube helical heat exchanger was designed to be molten salts reactor for hydrogen production. Model compounds (glycerol/glucose) and real biomass (corn cob) were successfully gasified in this molten salts reactor for producing hydrogen-rich gas. The unique temperature profiles of biomass slurry in the reactor were observed and compared with that of conventional electrical heating and direct solar heating approaches. Product gases yield, gasification efficiency and exergy conversion efficiency of the reactor were analyzed. The results showed that the performances of reactor were determined by feedstock style, biomass concentration, residence time and biomass slurry temperature profiles.     

An innovative biomass gasification process and its coupling with microturbine and fuel cell systems

The use of biomass, wood in particular, is one of the oldest forms of producing energy for heating or cooking. Nowadays, new technologies concerning the utilisation of biomass or waste residues are in demand and the trend to use them in decentralised applications for combined heat and power (CHP) production provides an attractive challenge to develop them. At the TU München an innovative allothermal gasification technology, the Biomass Heatpipe Reformer (BioHPR) has been developed. The aim of this project was to integrate the technology of liquid metal heatpipes in the gasification process in order to produce a hydrogen rich product gas from biomass or residues. The gasification product can be further used in microturbine or SOFC systems. The present paper presents the aforementioned gasification technology, its coupling with innovative CHP systems (with microturbine or fuel cells) and investigates, through the simulation of these systems, the optimum conditions of the integrated systems in order to reach the highest possible efficiencies.     

Thermodynamic analysis of hydrogen production from biomass gasification

An investigation is reported of the thermodynamic performance of the gasification process followed by the steam-methane reforming (SMR) and shift reactions for producing hydrogen from oil palm shell, one of the most common biomass resources. Energy and exergy efficiencies are determined for each component in this system. A process simulation tool is used for assessing the indirectly heated Battelle Columbus Laboratory (BCL) gasifier, which is included with the decomposition reactor to produce syngas for producing hydrogen. A simplified model is presented here for biomass gasification based on chemical equilibrium considerations, with the Gibbs free energy minimization approach. The gasifier with the decomposition reactor is observed to be one of the most critical components of a biomass gasification system, and is modeled to control the produced syngas yield. Also various thermodynamic efficiencies, namely energy, exergy and cold gas efficiencies are evaluated which may be useful for the design, optimization and modification of hydrogen production and other related processes.     

Investigation of a novel & integrated simulation model for hydrogen production from lignocellulosic biomass

Process simulation and modeling works are very important to determine novel design and operation conditions. In this study; hydrogen production from synthesis gas obtained by gasification of lignocellulosic biomass is investigated. The main motivation of this work is to understand how biomass is converted to hydrogen rich synthesis gas and its environmentally friendly impact. Hydrogen market development in several energy production units such as fuel cells is another motivation to realize these kinds of activities. The initial results can help to contribute to the literature and widen our experience on utilization of the CO₂ neutral biomass sources and gasification technology which can develop the design of hydrogen production processes. The raw syngas is obtained via staged gasification of biomass, using bubbling fluidized bed technology with secondary agents; then it is cleaned, its hydrocarbon content is reformed, CO content is shifted (WGS) and finally H₂ content is separated by the PSA (Pressure Swing Adsorption) unit. According to the preliminary results of the ASPEN HYSYS conceptual process simulation model; the composition of hydrogen rich gas (0.62% H₂O, 38.83% H₂, 1.65% CO, 26.13% CO₂, 0.08% CH₄, and 32.69% N₂) has been determined. The first simulation results show that the hydrogen purity of the product gas after PSA unit is 99.999% approximately. The mass lower heating value (LHV_mass) of the product gas before PSA unit is expected to be about 4500 kJ/kg and the overall fuel processor efficiency has been calculated as ～93%.     

Recent experimental advances on the utilization of biochar as a tar reforming catalyst: A review

Biomass gasification to form syngas is a promising renewable energy production process. Here, biomass is exposed to high temperatures in an oxygen-controlled environment where volatiles react to form components of syngas that can be used for energy or chemical production. A limitation to the use of gasification is the generation of tars that condense in downstream equipment causing damage and halting production. Currently tars are removed by physical, thermal, or catalytic processes, all high-cost options. On the other hand, biochar is produced as a solid by-product of gasification, characterized by high surface area, desirable adsorption properties, and relatively low cost. This review details the use of biochar as a catalyst to reform tars, while highlighting recent experimental advances in evaluating the effects of biomass composition, gasification conditions, and pre-treatment and post-treatment options to improve catalytic function. It discusses tar degradation mechanisms and catalyst deactivation and recommends further areas for research.     

Reduction of tars by dolomite cracking during two-stage gasification of olive cake

The effective implementation of biomass gasification has to overcome some difficulties such as the minimization of tars. On the other hand, with a proper design of experimental conditions, biomass gasification can be directed towards the production of hydrogen. The aim of the present study was to investigate the use of dolomite as catalyst to improve tar removal and hydrogen production by a two-stage steam gasification process, using olive cake as raw material. Fixing the olive cake gasification conditions on the first reactor (900 °C, steam flow rate of 190 mg min⁻¹, O₂ flow rate of 7.5 cm³ min⁻¹), the cracking of tars was prompted by: a) steam gasification (steam flow rate in the range 40-190 mg min⁻¹) at 1000 °C, b) catalytic gasification, using dolomite (5% wt.). It was found that increasing steam flow rate up to 110 mg min⁻¹ involves an increase in hydrogen fraction due to the enhancement of water gas and water gas shift reactions. Also, the influence of dolomite was studied at 800 and 900 °C in a second reactor, finding better results at 800 °C, which gave an hydrogen fraction of 0.51.     

Decentralized generation of electricity from biomass with proton exchange membrane fuel cell

Biomass can be applied as the primary source for the production of hydrogen in the future. The biomass is converted in an atmospheric fluidized bed gasification process using steam as the gasifying agent. The producer gas needs further cleaning and processing before the hydrogen can be converted in a fuel cell; it is assumed that the gas cleaning processes are able to meet the requirements for a PEM-FC. The compressed hydrogen is supplied to a hydrogen grid and can be used in small-scale decentralized CHP units. In this study it is assumed that the CHP units are based on low temperature PEM fuel cells. For the evaluation of alternative technologies the whole chain of centralized hydrogen production from biomass up to and including decentralized electricity production in PEM fuel cells is considered.Two models for the production of hydrogen from biomass and three models for the combined production of electricity and heat with PEM fuel cells are built using the computer program Cycle-Tempo. Two different levels of hydrogen purity are considered in this evaluation: 60% and 99.99% pure hydrogen. The purity of the hydrogen affects both the efficiencies of the hydrogen production as well as the PEM-FC systems. The electrical exergy efficiency of the PEM-FC system without additional heat production is calculated to be 27.66% in the case of 60% hydrogen and 29.06% in the case of 99.99% pure hydrogen. The electrical exergy efficiencies of the whole conversion chain appear to be 21.68% and 18.74%, respectively. The high losses during purification of the hydrogen gas result in a higher efficiency for the case with low purity hydrogen. The removal of the last impurities strongly increases the overall exergy losses of the conversion chain.     

Novel hydrogen‐rich gas production by steam gasification of biomass in a research‐scale rotary tubular helical coil gasifier

The concept of biomass steam gasification offers platform for production (i) of hydrogen, (ii) hydrocarbons and (iii) value added chemicals. Majority of these developments are either in nascent or in pilot/demonstration stage. In this context, there exists potential for hydrogen production via biomass steam gasification. Gaseous products of biomass steam gasification consist of large percentage of CO, CH₄ and other hydrocarbons, which can be converted to hydrogen through water‐gas‐shift reaction, steam reforming and cracking respectively. Although there are many previous research works showing the potential of production of hydrogen from biomass in a two stage process, challenges remain in extended biomass and char gasification so as to reduce the amount of carbon in the residual char as well as improve conversion of heavy hydrocarbon condensates to hydrogen rich gas. In the current work, the characteristics of biomass steam gasification in an in‐house designed rotary tubular helical coil reactor at temperatures less than 850 °C, in the presence of superheated steam, were presented. The objectives were to obtain high carbon conversion in the primary biomass steam gasification step (upstream) and high product gas yield and hydrogen yield in the secondary fixed bed catalytic step (downstream). The influence of temperature, steam‐to‐biomass ratio and residence time on product gas yield in the rotary tubular helical coil gasifier was studied in detail using one of the abundantly available biomass sources in India‐rice husk. Further, enhancement of product gas yield and hydrogen yield in a fixed bed catalytic converter was studied and optimized. In the integrated pathway, a maximum gas yield of 1.92 Nm³/kg moisture‐free biomass was obtained at a carbon conversion efficiency of 92%. The maximum hydrogen purity achieved under steady state conditions was 53% by volume with a hydrogen yield of 91.5 g/kg of moisture‐free biomass. This study substantiates overall feasibility of production of high value hydrogen from locally available biomass by superheated steam gasification followed by catalytic conversion. Copyright © 2016 John Wiley & Sons, Ltd.     

Supercritical water gasification of biomass for hydrogen production

Hydrogen from waste biomass is considered to be a clean gaseous fuel and efficient for heat and power generation due to its high energy content. Supercritical water gasification is found promising in hydrogen production by avoiding biomass drying and allowing maximum conversion. Waste biomass contains cellulose, hemicellulose and lignin; hence it is essential to understand their degradation mechanisms to engineer hydrogen production in high-pressure systems. Process conditions higher than 374 °C and 22.1 MPa are required for biomass conversion to gases. Reaction temperature, pressure, feed concentration, residence time and catalyst have prominent roles in gasification. This review focuses on the degradation routes of biomass model compounds such as cellulose and lignin at near and supercritical conditions. Some homogenous and heterogeneous catalysts leading to water–gas shift, methanation and other sub-reactions during supercritical water gasification are highlighted. The parametric impacts along with some reactor configurations for maximum hydrogen production and technical challenges encountered during hydrothermal gasification processes are also discussed.     

Lime enhanced biomass gasification. Energy penalty reduction by solids preheating in the calciner

Hydrogen is expected to be one of the most important energy carriers in the future. Gasification process may be used to produce hydrogen when joined with carbon capture technologies. Furthermore, the combination of biomass gasification and carbon capture presents a significant technical potential in net negative greenhouse gas emissions. Lime enhanced biomass gasification process makes use of CaO as a high temperature CO₂ carrier between the steam biomass gasifier and an oxy-fired regenerator. Important energy penalties derive from the temperature difference between the reactors (around 250–300 °C). A cyclonic preheater similar to those used in the cement industry may improve the energetic efficiency of the process if the particles entering the regenerator reactor are heated up by the gas leaving this reactor. A lime enhanced biomass gasification system was modelled and simulated. A cyclonic preheater was included to evaluate the improvement. Results show an increase of the gasification chemical efficiency and a reduction of the energy consumption in the regenerator.     

Detailed process modeling of a wood gasification combined heat and power plant

We provide the first process simulation able to depict a complete life cycle inventory of a biomass gasification combined heat and power (CHP) plant. The model predicts the detailed mass and energy balances, minor compounds emissions (such as NO_x, SO_x, aromatics, etc.). It is based on a phenomenological approach for dryer, reactors (gasification and combustion) and scrubber modeling. Process units are modeled with Aspen Plus® models completed with dedicated Fortran sub-models when more details are required. The gasifier is a Dual Fluidized Bed (DFB). It is decomposed in three sections, describing the three main mechanisms occurring in the reactor: wood pyrolysis, secondary reactions and char combustion. At the outlet of the gasifier, the complete composition of the syngas is predicted, which includes water, permanent gases, inorganics, particles and tars (phenol, benzene, toluene, styrene, indene, naphthalene, acenaphthylene, anthracene, phenanthrene, pyrene). Simulation results were validated against measurements from a pilot plant and other literature data. A wet conventional syngas cleaning system for gasification plant, including cyclone, catalytic tar cracker, syngas cooler, bag filters, water scrubber and wastewater treatment was considered and modeled. The complexity of tar composition allows a reliable determination of tar dew point. At the outlet of the cleaning system, syngas is burned in gas engines. Gaseous emissions (NO_x, SO_x, etc.) of the gas engines and the DFB combustor are also handled by the model as well as ashes and liquid waste. The predicted electrical and thermal efficiencies are 27 and 39% respectively.     

Model validation of a CFB biomass gasification model

The developed 1-dimensional biomass gasification mathematical model [1] was validated using the experimental results obtained from a circulating fluidized bed biomass gasifier. The reactor was operated on rice husk at various equivalence ratios (ER), fluidization velocities and biomass feed rates. The model gave reasonable predictions of the axial bed temperature profile, syngas composition and lower heating value (LHV), gas production rate, gasification efficiency and overall carbon conversion. The model was also validated by comparing the simulation results with two other different size circulating fluidized beds biomass gasifiers (CFBBGs) using different biomass feedstock, and it was concluded that the developed model can be applied to other CFBBGs using various biomass fuels and having comparable reactor geometries.     

Solar receiver/reactor for hydrogen production with biomass gasification in supercritical water

A novel receiver/reactor driven by concentrating solar energy for hydrogen production by supercritical water gasification (SCWG) of biomass was designed, constructed and tested. Model compound (glucose) and real biomass (corncob) were successfully gasified under SCW conditions to generate hydrogen-rich fuel gas in the apparatus. It is found that the receiver/reactor temperature increased with the increment of the direct normal solar irradiation (DNI). Effects of the DNI, the flow rates and concentration of the feedstocks as well as alkali catalysts addition were investigated. The results showed that DNI and flow rates of reactants have prominent effects on the temperature of reactor wall and gasification results. Higher DNI and lower feed concentrations favor the biomass gasification for hydrogen production. The encouraging results indicate a promising approach for hydrogen production with biomass gasification in supercritical water using concentrated solar energy.     

Process simulation of hydrogen production through biomass gasification: Introduction of torrefaction pre-treatment

Torrefaction is a pretreatment method that converts biomass to a fuel-like substance that can replace coal for sustainable power generation. In this work, a thermodynamic-based process simulation model was developed to simulate the gasification of empty fruit bunch (EFB), with torrefaction as pretreatment, to determine the optimum conditions; equivalence ratio, reactor temperature, torrefaction medium concentration, steam-to-biomass (S/B) ratio and system configuration were studied to determine their influence on hydrogen concentration, higher heating value (HHV), syngas ratio and cold gas efficiency (CGE). The highest hydrogen yield was obtained at an S/B ratio of 1.3 at 800 °C, with a syngas ratio of 2.5 and a CGE of 84%. Concentration of torrefaction medium showed no effect on hydrogen concentration due to the simplicity of the model used, but work is in progress in this direction. Therefore, steam gasification is more suitable than air gasification in hydrogen production.     

Analysis of the energy efficiency of solar aided biomass gasification for pure hydrogen production

This paper presents a simulative analysis of the energy efficiency of solar aided biomass gasification for pure hydrogen production. Solar heat has been considered as available at 250 °C in three gasification processes: i) gasification reactor followed by two water gas shift reactors and a pressure swing adsorber; ii) gasification reactor followed by an integrated membrane water gas shift reactor; iii) supercritical gasification reactor followed by two flash separators and a pressure swing adsorber.     

Solar thermochemical gasification of wood biomass for syngas production in a high-temperature continuously-fed tubular reactor

Biomass gasification is an attractive process to produce high-value syngas. Utilization of concentrated solar energy as the heat source for driving reactions increases the energy conversion efficiency, saves biomass resource, and eliminates the needs for gas cleaning and separation. A high-temperature tubular solar reactor combining drop tube and packed bed concepts was used for continuous solar-driven gasification of biomass. This 1 kW reactor was experimentally tested with biomass feeding under real solar irradiation conditions at the focus of a 2 m-diameter parabolic solar concentrator. Experiments were conducted at temperatures ranging from 1000 °C to 1400 °C using wood composed of a mix of pine and spruce (bark included) as biomass feedstock. This biomass was used under its non-altered pristine form but also dried or torrefied. The aim of this study was to demonstrate the feasibility of syngas production in this reactor concept and to prove the reliability of continuous biomass gasification processing using solar energy. The study first consisted of a parametric study of the gasification conditions to obtain an optimal gas yield. The influence of temperature, oxidizing agent (H₂O or CO₂) or type of biomass feedstock on the product gas composition was investigated. The study then focused on solar gasification during continuous biomass particle injection for demonstrating the feasibility of a continuous process. Regarding the energy conversion efficiency of the lab scale reactor, energy upgrade factor of 1.21 and solar-to-fuel thermochemical efficiency up to 28% were achieved using wood heated up to 1400 °C.     

串行流化床生物质气化制取富氢气体模拟研究

利用串行流化床技术将生物质热解气化和燃烧过程分开,气化反应器和燃烧反应器之间通过灰渣进行热量传递,实现了自供热下生物质气化制氢.利用Aapen Plus软件模拟制氢过程,通过比较单反应器生物质气化的模拟结果和实验结果,验证了模拟研究的可行性.重点研究串行流化床中非催化气化与CaCO3作用下的气化过程,探讨了气化温度、蒸汽与生物质的质量配比(S/B)对制氢的影响,为今后开展生物质气化制氢试验提供了理论参考.结果表明:对应不同气化温度,S/B都存在一个最佳值,且随着温度升高其值减小.当气化温度低于750℃时,添加CaCO3可大幅提高氢产率,气化温度为700℃且在S/B约为0.9时氢产率最大,达43.7 mol·(kg生物质)-1(干燥无灰基),比同温度下非催化气化提高了20.3%.随着气化温度升高,CaCO3促进作用减弱.     

A review on biomass‐based hydrogen production and potential applications

In this paper, a detailed review is presented to discuss biomass‐based hydrogen production systems and their applications. Some optimum hydrogen production and operating conditions are studied through a comprehensive sensitivity analysis on the hydrogen yield from steam biomass gasification. In addition, a hybrid system, which combines a biomass‐based hydrogen production system and a solid oxide fuel cell unit is considered for performance assessment. A comparative thermodynamic study also is undertaken to investigate various operational aspects through energy and exergy efficiencies. The results of this study show that there are various key parameters affecting the hydrogen production process and system performance. They also indicate that it is possible to increase the hydrogen yield from 70 to 107 g H₂ per kg of sawdust wood. By studying the energy and exergy efficiencies, the performance assessment shows the potential to produce hydrogen from steam biomass gasification. The study further reveals a strong potential of this system as it utilizes steam biomass gasification for hydrogen production. To evaluate the system performance, the efficiencies are calculated at particular pressures, temperatures, current densities, and fuel utilization factors. It is found that there is a strong potential in the gasification temperature range 1023–1423 K to increase energy efficiency with a hydrogen yield from 45 to 55% and the exergy efficiency with hydrogen yield from 22 to 32%, respectively, whereas the exergy efficiency of electricity production decreases from 56 to 49.4%. Hydrogen production by steam sawdust gasification appears to be an ultimate option for hydrogen production based on the parametric studies and performance assessments that were carried out through energy and exergy efficiencies. Finally, the system integration is an attractive option for better performance. Copyright © 2012 John Wiley & Sons, Ltd.     

Hydrogen energy production from disposable chopsticks by a low temperature catalytic gasification

This study investigates the comparison of various mineral catalysts on the enhancement of energy yield efficiency with low temperature catalytic gasification of disposable chopsticks. The experiments were carried out in a fluidized bed reactor by controlling the temperature and keeping it within the range of 600 °C–800 °C. The mineral catalysts, such as aluminum silicate, zeolite and calcium oxide (CaO) were used as the experimental catalysts for enhancing energy yield in this research. According to the experimental results, the gasification temperature is a critical factor for improving the gas yield and quality. In general, a higher temperature provides more favorable conditions for thermal cracking and enhances the gas yield and quality. The hydrogen content produced from the tested biomass gasification by various catalysts slightly increased from 11.77% to 14.57%. Furthermore, the lower heating value of synthesis gas increased from 9.28 MJ/Nm³ to 9.62 MJ/Nm³, when the fluidized bed reactor temperature operated at 600 °C and the tested catalysts addition. That is, the catalytic gasification has good energy yield performance for enhancing higher energy content of synthesis gas in a lower-temperature catalytic fluidized bed reactor. Compared with the hydrogen production efficiency, the addition of a calcium based catalyst can reduce bed agglomeration tendency, but it also improves the energy yield in this research.