Techno-economic evaluation of hydrogen refueling stations with liquid or gaseous stored hydrogen

In this study, different hydrogen refueling station (HRS) architectures are analyzed energetically as well as economically for 2015 and 2050. For the energetic evaluation, the model published in Bauer et al. [1] is used and norm-fitting fuelings according to SAE J2601 [2] are applied. This model is extended to include an economic evaluation. The compressor (gaseous hydrogen) resp. pump (liquid hydrogen) throughput and maximum pressures and volumes of the cascaded high-pressure storage system vessels are dimensioned in a way to minimize lifecycle costs, including depreciation, capital commitment and electricity costs. Various station capacity sizes are derived and energy consumption is calculated for different ambient temperatures and different station utilizations. Investment costs and costs per fueling mass are calculated based on different station utilizations and an ambient temperature of +12 °C. In case of gaseous trucked-in hydrogen, a comparison between 5 MPa and 20 MPa low-pressure storage is conducted. For all station configurations and sizes, a medium-voltage grid connection is applied if the power load exceeds a certain limit. For stations with on-site production, the electric power load of the hydrogen production device (electrolyzer or gas reformer) is taken into account in terms of power load. Costs and energy consumption attributed to the production device are not considered in this study due to comparability to other station concepts. Therefore, grid connection costs are allocated to the fueling station part excluding the production device. The operational strategy of the production device is also considered as energy consumption of the subsequent compressor or pump and the required low-pressure storage are affected by it. All station concepts, liquid truck-supplied hydrogen as well as stations with gaseous truck-supplied or on-site produced hydrogen show a considerable cost reduction potential. Long-term specific hydrogen costs of large stations (6 dispensers) are 0.63 €/kg – 0.76 €/kg (dependent on configuration) for stations with gaseous stored hydrogen and 0.18 €/kg for stations with liquid stored hydrogen. The study focuses only on the refueling station and does not allow a statement about the overall cost-effectiveness of different pathways.     

Improved safety by crossanalyzing quantitative risk assessment of hydrogen refueling stations

With the goal of building 310 hydrogen refueling stations (HRSs) in Korea by 2022, restrictions, such as location restrictions and separation distances, are being eased, so developing ways to improve technology and safety. As HRSs contain major facilities such as compressors, storage tanks, dispenser, and priority control panels, and a leakage could result in a large fire or explosion caused by an ignition source. To perform quantitative risk assessment, programs, namely, Hy-KoRAM and Phast/Safeti were used in this study. It could determine the damage range and effect on radiant heat and flame length, as well as personal and societal risks, using these programs. The crossanalysis of the two programs also improves the facility's safety and the reliability of the results.     

Construction of a structural equation model to identify public acceptance factors for hydrogen refueling stations under the provision of risk and safety information

Hydrogen refueling stations (HRSs) are an inevitable infrastructure for the utility of fuel cell vehicles; however, they can raise public safety concerns. The aim of this study is to establish a framework for public acceptance of HRSs in Japan upon the provision of risk and/or safety measure information on HRSs. We executed an in-person interview survey asking the respondents about their acceptance of HRSs and then constructed a structural equation model on HRS acceptance with four endogenous factors. The common factors to determine acceptability were “Dread” and “Independent”. “Balance” was added to the factors for the risk-informed group. If risk information was provided, people tended to judge based on their inherent sense of “Balance”; however, if it was not provided, their judgment was based on their intuitive “Dread” of HRSs or hydrogen. This study reveals risk perception characteristics and attempts to promote improved risk communication prior to HRS installation.     

Quantitative risk assessment of a mobile hydrogen refueling station in Korea

Hydrogen infrastructure is expanding. Mobile hydrogen refueling stations are advantageous because they can be moved between locations to provide refueling. However, there are serious concerns over the risk of various accident scenarios as the refueling stations are transported. In this study, we conduct a quantitative risk assessment of a mobile hydrogen refueling station. Risks that may occur at two refueling locations and the transport path between them are analyzed. Our evaluation reveals that risks are mostly in an acceptable zone and to a lesser degree in a conditionally acceptable zone. The greatest single risk factor is an accident resulting from the rupture of the tube trailer at the refueling site. At sites with no tube trailer and during the transport, the risk is greatest from large leaks from the dispenser or compressed gas facility. The mobile hydrogen refueling station can be safely built within acceptable risk levels.     

Refueling-station costs for metal hydride storage tanks on board hydrogen fuel cell vehicles

Refueling costs account for much of the fuel cost for light-duty hydrogen fuel-cell electric vehicles. We estimate cost savings for hydrogen dispensing if metal hydride (MH) storage tanks are used on board instead of 700-bar tanks. We consider a low-temperature, low-enthalpy scenario and a high-temperature, high-enthalpy scenario to bracket the design space. The refueling costs are insensitive to most uncertainties. Uncertainties associated with the cooling duty, coolant pump pressure, heat exchanger (HX) fan, and HX operating time have little effect on cost. The largest sensitivities are to tank pressure and station labor. The cost of a full-service attendant, if the refueling interconnect were to prevent self-service, is the single largest cost uncertainty. MH scenarios achieve $0.71–$0.75/kg-H₂ savings by reducing compressor costs without incurring the cryogenics costs associated with cold-storage alternatives. Practical refueling station considerations are likely to affect the choice of the MH and tank design.     

A review on current trends in potential use of metal-organic framework for hydrogen storage

Hydrogen can be a promising clean energy carrier for the replenishment of non-renewable fossil fuels. The set back of hydrogen as an alternative fuel is due to its difficulties in feasible storage and safety concerns. Current hydrogen adsorption technologies, such as cryo-compressed and liquefied storage, are costly for practical applications. Metal-organic frameworks (MOFs) are crystalline materials that have structural versatility, high porosity and surface area, which can adsorb hydrogen efficiently. Hydrogen is adsorbed by physisorption on the MOFs through weak van der Waals force of attraction which can be easily desorbed by applying suitable heat or pressure. The strategies to improve the MOFs surface area, hydrogen uptake capacities and parameters affecting them are studied. Hydrogen spill over mechanism is found to provide high-density storage when compared to other mechanisms. MOFs can be used as proton exchange membranes to convert the stored hydrogen into electricity and can be used as electrodes for the fuel cells. In this review, we addressed the key strategies that could improve hydrogen storage properties for utilizing hydrogen as fuel and opportunities for further growth to meet energy demands.     

Underground hydrogen storage in Australia: A review on the feasibility of geological sites

Hydrogen has attracted attention worldwide with its favourable inherent properties to contribute towards a carbon-free green energy future. Australia aims to make hydrogen as its next major export component to economize the growing global demand for hydrogen. Cost-effective and safe large-scale hydrogen storage in subsurface geology can assist Australia in meeting the projected domestic and export targets. This article discusses the available subsurface storage options in detail by first presenting the projected demand for hydrogen storage. Australia has many subsurface formations, such as depleted gas fields, salt caverns, aquifers, coal seams and abandoned underground mines, which can contribute to underground hydrogen storage. The article presents basin-wide geological information on the storage structures, the technical challenges, and the factors to consider during site selection. With the experience and knowledge Australia has in utilizing depleted reservoirs for gas storage and carbon capture and sequestration, Australia can benefit from the depleted gas reservoirs in developing hydrogen energy infrastructure. The lack of experience and knowledge associated with other geostructures favours the utilization of underground gas storage sites for the storage of hydrogen during the initial stages of the shift towards hydrogen energy. The article also provides future directions to address the identified important knowledge gaps to utilize the subsurface geology for hydrogen storage successfully.     

Design and computational analysis of a metal hydride hydrogen storage system with hexagonal honeycomb based heat transfer enhancements-part A

In this study, design and performance analysis is carried out for a 10 kWh metal hydride based hydrogen storage system. The system is equipped with distinctive aluminium hexagonal honeycomb based heat transfer enhancements (HTE) having higher surface area to volume ratio for effective heat transfer combined with low system weight addition. The system performance was studied under different operating conditions. The optimum absorption condition was achieved at 35 bar with water at room temperature as heat transfer fluid where up to 90% absorption was completed in 7200 s. The performance of the reactor was observed to significantly improve upon the addition of the HTE network at a minimal system weight penalty.     

Reinforcement learning based energy management systems and hydrogen refuelling stations for fuel cell electric vehicles: An overview

This paper examines the current state of the art of hydrogen refuelling stations-based production and storage systems for fuel cell hybrid electric vehicles (FCHEV). Nowadays, the emissions are increasing rapidly due to the usage of fossil fuels and the demand for hydrogen refuelling stations (HRS) is emerging to replace the conventional vehicles with FCHEVs. Hence, the availability of HRS and its economic aspects are discussed. In addition, a comprehensive study is presented on the energy storage systems such as batteries, supercapacitors and fuel cells which play a major role in the FCHEVs. An energy management system (EMS) is essential to meet the load requirement with effective utilisation of power sources with various optimizing techniques. A detailed comparative analysis is presented on the merits of Reinforcement learning (RL) for the FCHEVs. The significant challenges are discussed in depth with potential solutions for future work.     

Studies on 10kg alloy mass metal hydride based reactor for hydrogen storage

A 10 kg alloy mass metal hydride reactor, with LaNi₅ alloy was designed. Heat transfer enhacement in the reactor was achieved by including embedded cooling tubes and an external water jacket. Detailed parametric study has been carried to understand the performance of the system. The effect of both geometrical and operational parameters was studied in simulations. The optimized geometrical parameters were used for fabricating the reactor. Experimental studies were carried on the fabricated reactor. Absorption studies were carried out for different supply pressure and different cooling fluid temperatures. Storage capacity of 1.13 wt% was found in 1620 s at a supply pressure of 25 bar and with a flow rate of 20 LPM. Similarily, desorption studies were carried out for varying heat transfer fluid temperatures. Complete and fastest desorption was observed at 80 °C with the reaction completion time of 2700 s.     

A techno-economic study for a hydrogen storage system in a microgrid located in baja California,Mexico. Levelized cost of energy for power to gas to power scenarios

In this work a techno economic feasibility study is carried out to implement a Hydrogen based Power to Gas to Power (P2G2P) in a Microgrid, located in a rural area in Baja California, Mexico. The study aims to define the feasibility to store energy throughout seasons with this novel alternative using an electrolyzer to produce green hydrogen from excess renewable energy in winter, to store it during months and re inject it to the grid as electricity by a fuel cell in the high energy demanding season. The Microgrid was modeled in Homer software and simulations of the P2G2P lead to Levelized Cost of Energy data to compare between the P2G2P scenarios and the current diesel-battery based solution to complete the high demand by the community. This study shows that using hydrogen and fuel cells to substitute diesel generators it is possible to reduce CO₂ emissions up to a 27% and that in order for the P2G2P to be cost competitive, the fuel cell should reduce its cost in 50%; confirming that, in the medium to long term, the hydrogen storage system is a coherent alternative towards decarbonization of the distributed energy generation.     

Thermophysical properties of the liquid organic hydrogen carrier system based on diphenylmethane with the byproducts fluorene or perhydrofluorene

Fluorene (H0-F) and perhydrofluorene (H12-F) represent process-related byproducts formed by a dehydrocyclization step in the liquid organic hydrogen carrier (LOHC) system based on diphenylmethane (H0-DPM) and dicyclohexylmethane (H12-DPM). The influence of these byproducts on the liquid viscosity, surface tension, and liquid density of the DPM-based system was experimentally determined by studying three dehydrogenated binary mixtures with H0-F mole fractions of 0.05, 0.10, and 0.20 as well as one hydrogenated binary mixture with an H12-F mole fraction of 0.10 close to 0.1 MPa from (283–573) K. The densities increase with increasing share of H0-F or H12-F by around 1% per added byproduct mole fraction of 0.1. For the surface tension, an increase relative to the values of H0-DPM or H12-DPM by up to 6% is found. The addition of H0-F to H0-DPM or H12-F to H12-DPM yields a relative increase in viscosity by up to 9% at the lowest temperature studied.     

GIS-based analysis of rock salt deposits’ suitability for underground hydrogen storage

The paper discusses the suitability of bedded salt deposits for underground hydrogen storage facilities. The presented research is an example of multi-criteria decision analysis coupled with spatial data analysis undertaken using GIS (Geographic Information System). The aim of this study is to develop a methodology for selecting the best locations for hydrogen storage in salt caverns. In the analysis, we take into account the results of previous studies of the storage capacity of rock salt deposits. The presented methodology allows the creation of rock salt deposit suitability maps for underground hydrogen storage. The results show that the applied method significantly influences the resulting map image, helping to identify optimal locations for hydrogen storage facilities. The presented approach may be of value to governmental institutions considering underground hydrogen storage, geological services, power plants producing electricity from renewable energy sources, and chemical and petrochemical plants.     

Novel sonochemical synthesis of Zn2V2O7 nanostructures for electrochemical hydrogen storage

Although utilization of diverse classes of metal oxides as hydrogen storage materials has been reported, but there is still a major need to introduce efficient materials. Herein, mesoporous Zn₂V₂O₇ nanostructures were produced by a new sonochemical method using hydrazine, zinc nitrate, and ammonium vanadate as the starting reagents and then annealed at 700 °C. Prior to annealing, Zn₃V₃O₈ was produced in the presence of ultrasonic waves, whereas in the absence of ultrasonic waves, Zn₂(VO₄)₂ was the major product. In fact, ultrasonic waves interfered with the reaction mechanism and reduced V⁵⁺ to V⁴⁺ and V³⁺. Because of the proper composition and structure of these nanostructures, they were used for electrochemical storage of hydrogen. Storage of over 2899 mAh/g after 20 cycles by flower-like nanostructures revealed their high capability. The results also showed that morphology affects efficiency such that three-dimensional spherical nanostructures had a storage capacity of 2247 mAh/g after 20 cycles.     

Effect of introducing manganese as additive on microstructure,hydrogen storage properties and rate limiting step of Ti–Cr alloy

TiCr₂ with adding different amount of Mn (0, 2, 4 and 8 wt.%) alloys have been investigated. All alloys have C14-type main phase (gray color in SEM) and Ti minor phase (dark gray color in SEM). Rietveld fitting results proved that the lattice parameter a and cell volume of C14-type phase decreased with increasing Mn content. The first hydrogenation measurement manifest that all alloys have best activation properties and could be activated without any prior heat treatment and hydrogen exposure. However, introducing Mn led to the decrease of the first hydrogen absorption rate of TiCr₂ alloy, which may be due to the decrease of cell volume of C14-type main phase. The first hydrogenation properties at low temperature and effect of air exposure of the alloy were discussed. The results showed that the maximum hydrogen absorption capacity at 0 °C was obviously higher than that at room temperature. In addition, TiCr₂ alloy doped with minor amounts of Mn after long-time air exposure showed better hydrogenation performance. This may be due to the Mn additive acting as a deoxidizer. Finally, the first hydrogenation kinetic mechanisms of all alloys at different temperature were also studied by using the rate limiting step.     

Economic viability assessment of sustainable hydrogen production,storage, and utilisation technologies integrated into on- and off-grid micro-grids: A performance comparison of different meta-heuristics

In recent years, there has been considerable interest in the development of zero-emissions, sustainable energy systems utilising the potential of hydrogen energy technologies. However, the improper long-term economic assessment of costs and consequences of such hydrogen-based renewable energy systems has hindered the transition to the so-called hydrogen economy in many cases. One of the main reasons for this is the inefficiency of the optimization techniques employed to estimate the whole-life costs of such systems. Owing to the highly nonlinear and non-convex nature of the life-cycle cost optimization problems of sustainable energy systems using hydrogen as an energy carrier, meta-heuristic optimization techniques must be utilised to solve them. To this end, using a specifically developed artificial intelligence-based micro-grid capacity planning method, this paper examines the performances of twenty meta-heuristics in solving the optimal design problems of three conceptualised hydrogen-based micro-grids, as test-case systems. Accordingly, the obtained numeric simulation results using MATLAB indicate that some of the newly introduced meta-heuristics can play a key role in facilitating the successful, cost-effective development and implementation of hydrogen supply chain models. Notably, the moth-flame optimization algorithm is found capable of reducing the life-cycle costs of micro-grids by up to 6.5% as compared to the dragonfly algorithm.     

Superior anti-impurity gas poisoning ability and hydrogen storage properties of Ti–Cr alloy by introducing zirconium as additive

In this work, the anti-impurity gas poisoning ability and hydrogen storage properties of Ti–Cr alloy by introducing zirconium as additive have been investigated. The results showed that all alloys had C14-type main phase and Ti minor phase. The lattice parameter a, c and cell volume of the C14-type phase rose as Zr content increased. Furthermore, after introducing Zr, all alloys could absorb hydrogen immediately without any prior heat treatment or hydrogen exposure with/without prolonged air exposure. The maximum hydrogen storage capacity and the average effective hydrogen storage capacity of TiCr₂ alloy also increased with Zr content. The cycle properties of all alloys with/without prolonged air exposure were also discussed. The results showed that all alloys had good cycle stability even if the alloys were exposed to the air for 2 days. The above results suggested that the addition of Zr had a positive effect on improving the hydrogen storage properties and anti-impurity gas poisoning properties of TiCr₂ alloy. Finally, the mechanisms of first hydrogenation kinetic of all alloys with/without prolonged air exposure were also investigated by using the rate limiting step.     

Performance analysis of a novel solar PTC integrated system for multi-generation with hydrogen production

The performance analysis of a novel multi-generation (MG) system that is developed for electricity, cooling, hot water and hydrogen production is presented in this study. MG systems in literature are predominantly built on a gas cycle, integrated with other thermodynamic cycles. The aim of this study is to achieve better thermodynamic (energy and exergy) performance using a MG system (without a gas cycle) that produces hydrogen. A proton exchange membrane (PEM) utilizes some of the electricity generated by the MG system to produce hydrogen. Two Rankine cycles with regeneration and reheat principles are used in the MG configuration. Double effect and single effect absorption cycles are also used to produce cooling. The electricity, hot water, cooling effect, and hydrogen production from the multi-generation are 1027 kW, 188.5 kW, 11.23 kg/s and 0.9785 kg/h respectively. An overall energy and exergy efficiency of 71.6% and 24.5% respectively is achieved considering the solar parabolic trough collector (PTC) input and this can increase to 93.3% and 31.9% if the input source is 100% efficient. The greenhouse gas emission reduction of this MG system is also analyzed.     

Effect of high compression ratio on improving thermal efficiency and NOx formation in jet plume controlled direct-injection near-zero emission hydrogen engines

The Plume Ignition and Combustion Concept (PCC) developed by the authors significantly reduced nitrogen oxide (NOx) emissions in a direct-injection hydrogen engine under high-load operation. With PCC, a rich fuel plume is ignited immediately after completion of injection in the latter half of the compression stroke to reduce NOx formation. Simultaneously, high thermal efficiency was also achieved by mitigating cooling losses through optimization of the jet configuration in the combustion chamber. This basic combustion concept was applied to burn lean mixture in combination with the optimized hydrogen jet configuration and the application of supercharging to recover the power output decline due to the use of a diluted mixture. As a result, a near-zero-emission-level engine has been achieved that simultaneously provides high thermal efficiency, high power output and low NOx emissions at a single-digit ppm level [1]. In this study, a high compression ratio was applied to improve thermal efficiency further by taking advantage of the characteristics of hydrogen fuel, especially its diluted mixture with a high anti-knock property. As a result, NOx emissions at a single-digit ppm level and gross indicated thermal efficiency of 52.5% were achieved while suppressing knocking at a compression ratio of 20:1 by optimizing the excess air ratio and injection timing, and increasing power output by supercharging.     

Review of hydrogen economy in Malaysia and its way forward

Heavy fossil fuels consumption has raised concerns over the energy security and climate change while hydrogen is regarded as the fuel of future to decarbonize global energy use. Hydrogen is commonly used as feedstocks in chemical industries and has a wide range of energy applications such as vehicle fuel, boiler fuel, and energy storage. However, the development of hydrogen energy in Malaysia is sluggish despite the predefined targets in hydrogen roadmap. This paper aims to study the future directions of hydrogen economy in Malaysia considering a variety of hydrogen applications. The potential approaches for hydrogen production, storage, distribution and application in Malaysia have been reviewed and the challenges of hydrogen economy are discussed. A conceptual framework for the accomplishment of hydrogen economy has been proposed where renewable hydrogen could penetrate Malaysia market in three phases. In the first phase, the market should aim to utilize the hydrogen as feedstock for chemical industries. Once the hydrogen production side is matured in the second phase, hydrogen should be used as fuel in internal combustion engines or burners. In the final phase hydrogen should be used as fuel for automobiles (using fuel cell), fuel-cell combined heat and power (CHP) and as energy storage.