Performance and combustion characteristic of CI engine fueled with hydrogen enriched diesel

The combustion of hydrogen–diesel blend fuel was investigated under simulated direct injection (DI) diesel engine conditions. The investigation presented in this paper concerns numerical analysis of neat diesel combustion mode and hydrogen enriched diesel combustion in a compression ignition (CI) engine. The parameters varied in this simulation included: H₂/diesel blend fuel ratio, engine speed, and air/fuel ratio. The study on the simultaneous combustion of hydrogen and diesel fuel was conducted with various hydrogen doses in the range from 0.05% to 50% (by volume) for different engine speed from 1000 – 4000 rpm and air/fuel ratios (A/F) varies from 10 – 80. The results show that, applying hydrogen as an extra fuel, which can be added to diesel fuel in the (CI) engine results in improved engine performance and reduce emissions compared to the case of neat diesel operation because this measure approaches the combustion process to constant volume. Moreover, small amounts of hydrogen when added to a diesel engine shorten the diesel ignition lag and, in this way, decrease the rate of pressure rise which provides better conditions for soft run of the engine. Comparative results are given for various hydrogen/diesel ratio, engine speeds and loads for conventional Diesel and dual fuel operation, revealing the effect of dual fuel combustion on engine performance and exhaust emissions.     

Crude palm oil fuel for diesel-engines: Experimental and ANN simulation approaches

In the current work, the effect of using CPO (crude palm oil)-OD (ordinary diesel) blends as fuel on the performance of CI (compression ignition) engine is studied. Three different blends of CPO-OD (25%, 50% and 75%) were investigated using direct-injection, stationary diesel engine. The CPO-OD blends were preheated to about 60 °C before the injection to reduce the viscosity of the blends. The experiments were conducted at variable engine speeds (1000 rpm through 3000 rpm) under fixed throttle opening. The results revealed that the CPO-OD exhibited higher torque and power output at engine speeds lower than 2000 rpm, while the BSFC (brake specific fuel consumption) was found to be higher than the OD at the same engine speeds. CPO enhanced the BSFC at higher engine speeds (above 2000 rpm). The CPO-OD blends exhibited lower emissions of NO_x and higher emission of CO compared to the OD.     

Effect of advanced injection timing on emission characteristics of diesel engine running on natural gas

There has been a growing concern on the emission of greenhouse gases into the atmosphere, whose consequence is global warming. The sources of greenhouse gases have been identified, of which the major contributor is the combustion of fossil fuel. Researchers have intensified efforts towards identifying greener alternative fuel substitutes for the present fossil fuel. Natural gas is now being investigated as potential alternative fuel for diesel engines. Natural gas appears more attractive due to its high octane number and perhaps, due to its environmental friendly nature. The test results showed that alternative fuels exhibit longer ignition delay, with slow burning rates. Longer delays will lead to unacceptable rates of pressure rise with the result of diesel knock. This work examines the effect of advanced injection timing on the emission characteristics of dual-fuel engine. The engine has standard injection timing of 30° BTDC. The injection was first advanced by 5.5° and given injection timing of 35.5° BTDC. The engine performance was erratic on this timing. The injection was then advanced by 3.5°. The engine performance was smooth on this timing especially at low loading conditions. The ignition delay was reduced through advanced injection timing but tended to incur a slight increase in fuel consumption. The CO and CO₂ emissions were reduced through advanced injection timing.     

Effect of injection parameters on the combustion and emission characteristics in a common-rail direct injection diesel engine fueled with waste cooking oil biodiesel

The objective of this paper was to study the effects of the injection pressure and injection timing on the combustion and emission characteristics in a single-cylinder common-rail direct injection (CRDI) diesel engine fueled with waste cooking oil (WCO) biodiesel and commercial diesel fuel. The fuel property including fatty acid composition for the biodiesel were measured and compared with those of the conventional diesel fuel. The engine tests were conducted at two injection pressures (80 and 160 MPa) and different injection timings from −25 to 0 crank angle degree (CAD) after top dead center (aTDC) under two different engine loads. The results showed that the indicated specific fuel consumption (ISFC) with respect to the injection timings of the biodiesel was higher than that of the diesel fuel under all experimental conditions. The peak cylinder pressure and the peak heat release rate of the biodiesel were slightly lower, while the ignition delay was slightly longer under all operating conditions. In terms of emissions, the biodiesel had benefits in reduction of smoke, carbon monoxide (CO), hydrocarbon (HC) emissions especially with high fuel injection pressure. The nitrogen oxide (NO_x) emissions of the biodiesel were relatively higher than those of the diesel under all experimental conditions.     

Combustion characteristics of a 4-stroke CI engine operated on Honge oil,Neem and Rice Bran oils when directly injected and dual fuelled with producer gas induction

Energy is an essential requirement for economic and social development of any country. Sky rocketing of petroleum fuel costs in present day has led to growing interest in alternative fuels like vegetable oils, alcoholic fuels, CNG, LPG, Producer gas, biogas in order to provide a suitable substitute to diesel for a compression ignition (CI) engine. The vegetable oils present a very promising alternative fuel to diesel oil since they are renewable, biodegradable and clean burning fuel having similar properties as that of diesel. They offer almost same power output with slightly lower thermal efficiency due to their lower energy content compared to diesel. Utilization of producer gas in CI engine on dual fuel mode provides an effective approach towards conservation of diesel fuel. Gasification involves conversion of solid biomass into combustible gases which completes combustion in a CI engines. Hence the producer gas can act as promising alternative fuel and it has high octane number (100–105) and calorific value (5–6 MJ/Nm³). Because of its simpler structure with low carbon content results in substantial reduction of exhaust emission. Downdraft moving bed gasifier coupled with compression ignition engine are a good choice for moderate quantities of available mass up to 500 kW of electrical power. Hence bio-derived gas and vegetable liquids appear more attractive in view of their friendly environmental nature. Experiments have been conducted on a single cylinder, four-stroke, direct injection, water-cooled CI engine operated in single fuel mode using Honge, Neem and Rice Bran oils. In dual fuel mode combinations of Producer gas and three oils were used at different injection timings and injection pressures.Dual fuel mode of operation resulted in poor performance at all the loads when compared with single fuel mode at all injection timings tested. However, the brake thermal efficiency is improved marginally when the injection timing was advanced. Decreased smoke, NO_x emissions and increased CO emissions were observed for dual fuel mode for all the fuel combinations compared to single fuel operation.     

Combustion performance and emission reduction characteristics of automotive DME engine system

This article is a condensed overview of a dimethyl ether (DME) fuel application for a compression ignition diesel engine. In this review article, the spray, atomization, combustion and exhaust emissions characteristics from a DME-fueled engine are described, as well as the fundamental fuel properties including the vapor pressure, kinematic viscosity, cetane number, and the bulk modulus. DME fuel exists as gas phase at atmospheric state and it must be pressurized to supply the liquid DME to fuel injection system. In addition, DME-fueled engine needs the modification of fuel supply and injection system because the low viscosity of DME caused the leakage. Different fuel properties such as low density, viscosity and higher vapor pressure compared to diesel fuel induced the shorter spray tip penetration, wider cone angle, and smaller droplet size than diesel fuel. The ignition of DME fuel in combustion chamber starts in advance compared to diesel or biodiesel fueled compression ignition engine due to higher cetane number than diesel and biodiesel fuels. In addition, DME combustion is soot-free since it has no carbon–carbon bonds, and has lower HC and CO emissions than that of diesel combustion. The NO_x emission from DME-fueled combustion can be reduced by the application of EGR (exhaust gas recirculation). This article also describes various technologies to reduce NO_x emission from DME-fueled engines, such as the multiple injection strategy and premixed combustion. Finally, the development trends of DME-fueled vehicle are described with various experimental results and discussion for fuel properties, spray atomization characteristics, combustion performance, and exhaust emissions characteristics of DME fuel.     

Numerical Investigation of the Effect of Hydrogen Enrichment on an Opposed-Piston Compression Ignition Diesel Engine

High power-to-weight and fuel efficiency are bounded with opposed-piston compression ignition(OPCI) engine, which makes it ideal in certain applications. In the present study, a dynamic three-dimensional CFD model was established to numerically investigate the combustion process and emission formation of a model OPCI engine with hydrogen enrichment. The simulation results indicated that a small amount of hydrogen was efficient to improve the indicated power owing to the increased in-cylinder pressure. Hydrogen tended to increase the ignition delay of diesel fuel due to both dilution and chemical effect. The burning rate of diesel fuel was apparently accelerated when mixing with hydrogen and premixed combustion became dominated. NO_x increased sharply while soot was sufficiently suppressed due to the increase of in-cylinder temperature. Preliminary modifications on diesel injection strategy including injection timing and injection pressure were conducted. It was notable that excessive delayed injection timing could reduce NO_x emission but deteriorate the indicated power which was mainly attributed to the evident decline of hydrogen combustion efficiency. This side effect could be mitigated by increasing the diesel injection pressure. Appropriate delay of injection coupled with high injection pressure was suggested to deal with trade-offs among NO_x, soot and engine power.     

Influence of biodiesel on engine combustion and emission characteristics

This paper discusses the influence of biodiesel on the engine combustion characteristics. The considered fuel is neat biodiesel from rapeseed oil. The considered engine is a bus diesel engine with injection M system. The engine characteristics are obtained by experiments and numerical simulation. The results obtained with biodiesel are compared to those obtained with mineral diesel under various operating regimes. In this way, the influences of biodiesel usage on the injection pressure, injection timing, ignition delay, in-cylinder gas pressure and temperature, heat release rate, exhaust gas temperatures, harmful emissions, specific fuel consumption, and on engine power are analyzed. Furthermore, the relationships among fuel properties, injection and combustion characteristics, harmful emissions, and other engine performance are determined. Special attention is given to possible explanations of higher NO_x emission in spite of lower in-cylinder gas temperature.     

Effect of addition of hydrogen and TiO2 in gasoline engine in various exhaust gas recirculation ratio

The effects of hydrogen ratios on combustion and emission characteristics of gasoline engine were studied under different exhaust gas recirculation (EGR), ignition timing and ignition pressure. The test performed in a modified gasoline direct ignition engine at different hydrogen ratios of 0%, 5%, 10% and 25%. In addition, the EGR rate set to 0%, 5%, 10% and 20% to study the combustion and emission characteristics. Addition to the different hydrogen fractions, 5% of TiO₂ is added to increase the combustion characteristics with reduced emission. Regarding the results of the current study, the engine torque increases by 15% due to the addition of hydrogen in gasoline, while mechanical efficiency is improved by achieving a large throttle opening. At the same time, NOx emission decreased by 62% compared to the unmodified engine due to the influence of EGR, hydrogen ratio and high oxygen concentration TiO₂. Moreover, the emission of CO and HC also reduced due to the influence of hydrogen fuel. Additionally, few more tests are taken to monitor the effect of the injection pressure for the hydrogen fuel. Higher injection reports higher effective thermal efficiency at 4 MPa and lower NOx. Reasonable injection pressure results in shorten flame development period.     

Effect of pilot fuel injection pressure and injection timing on combustion,performance and emission of hydrogen-biodiesel dual fuel engine

The present study highlights the influence of fuel injection pressure (FIP) and fuel injection timing (FIT) of Jatropha biodiesel as pilot fuel on the performance, combustion and emission of a hydrogen dual fuel engine. The hydrogen flow rates used in this study are 5lit/min, 7lit/min, and 9lit/min. The pilot fuel is injected at three FIPs (500, 1000, and 1500 bar) and at three FITs (5°, 11°, and 17?bTDC). The results showed an increase in brake thermal efficiency (B_th)from 25.02% for base diesel operation to 32.15% for hydrogen-biodiesel dual fuel operation with 9lit/min flow rate at a FIP of 1500 bar and a FITof17?bTDC. The cylinder pressure and heat release rate (HRR) are also found to be higher for higher FIPs. Advancement in FIT is found to promote superior HRR for hydrogen dual fuel operations. The unburned hydrocarbon (UHC) and soot emissions are found to reduce by 59.52% and 46.15%, respectively, for hydrogen dual fuel operation with 9lit/min flow rate at a FIP of 1500 bar and a FIT of 11?bTDC. However, it is also observed that the oxides of nitrogen (NO_X) emissions are increased by 20.61% with 9lit/min hydrogen flow rate at a FIP of 1500 bar and a FIT of 17?bTDC. Thus, this study has shown the potential of higher FIP and FIT in improving the performance, combustion and emission of a hydrogen dual fuel engine with Jatropha biodiesel as pilot fuel.     

Effect of induction on exhaust gas recirculation and hydrogen gas in compression ignition engine with simarouba oil in dual fuel mode

Biofuels extracted from non-edible oil is sustainable and can be used as an alternative fuel for internal combustion engines. This study presents the performance, emission and combustion characteristic analysis by using simarouba oil (obtained from Simarouba seed) as an alternative fuel along with hydrogen and exhaust gas recirculation (EGR) in a compression ignition (CI) engine operating on dual fuel mode. Simarouba biofuel blend (B20) was prepared on volumetric basis by mixing simarouba oil and diesel in the proportion of 20% and 80% (v/v), respectively. Hydrogen gas was introduced at the flow rate of 2.67 kg/min, and EGR concentration was maintained at 30% of total air introduction. Performance, combustion and emission characteristics analysis were examined with biodiesel (B20), biodiesel with hydrogen substitution and biodiesel, hydrogen with EGR and were compared with neat diesel operation. Results indicate that BTE of the engine operating with biodiesel B20 was decreased when compared to neat diesel operation. However, introducing hydrogen along with B20 blend into the combustion chamber shows a slight increase in the BTE by 1%. NO_x emission was increased to 18.13% with the introduction of hydrogen than that of base fuel (diesel) operation. With the introduction of EGR, there is a significant reduction in NO_x emission due to decrease in in-cylinder temperature by 19.07%. A significant reduction in CO, CO_2, and smoke emissions were also noted with the introduction of both hydrogen and EGR. The ignition delay and combustion duration were increased with the introduction of hydrogen, EGR with biodiesel than neat diesel operation. Hence, the proposed biodiesel B20 with H₂ and EGR combination can be applied as an alternative fuel in CI engines.     

Effect of hydrogen enrichment in the intake air of diesel engine fuelled with honge biodiesel blend and diesel

In the current investigation, the enrichment of hydrogen with the honge biodiesel blend and diesel is used in a compression ignition engine. The biodiesel is derived from the honge oil and mixed with diesel fuel by 20% (v/v). Thereafter, hydrogen at different volume flow rates (10 and 13 lpm) is introduced into the intake manifold. The outcomes by enrichment of hydrogen on the performance, combustion and emission characteristics are investigated by examining the brake thermal efficiency, fuel consumption, HC, CO, CO₂, NOₓ emissions, in-cylinder pressure, combustion duration, and rate of heat release. The engine fuelled with honge biodiesel blend is found to enhance the thermal efficiency, combustion characteristics. Compare to diesel, the BTE increased by 2.2% and 6% less fuel consumption for the HB20 + 13H₂ blend. Further, reduction in the emission of exhausts gases like CO and HC by 21% and 24%, respectively, are obtained. This is due to carbon-free structure in hydrogen. Moreover, due to high pressure in the cylinder, there is a slight increase in oxides of nitrogen emission compare to diesel. The combustion characteristics such as rate of heat release, combustion duration, and maximum ₂rate of pressure rise and in-cylinder pressure are high due to hydrogen.     

Unregulated emissions and health risk potential from biodiesel (KB5, KB20) and methanol blend (M5) fuelled transportation diesel engines

Diesel engine emissions consist of several harmful gaseous species, some of which are regulated by stringent emission norms, while many others are not. These unregulated emission species are responsible for adverse environmental impact and serious health hazards upon prolonged exposure. In this study, a four-cylinder, 1.4 l, compression ignition (CI) engine was used for characterization of unregulated gaseous exhaust emissions measured at 2500 rpm at varying engine loads (0, 25, 50, 75 and 100%). The test fuels investigated were Karanja biodiesel blended with diesel (KB5, KB20), methanol blended with diesel (M5) and baseline mineral diesel. Fourier transform infrared (FTIR) emission analyzer was used to measure unregulated emission species and raw exhaust gas emission analyzer was used to measure regulated emission species in exhaust. Results show an increasing trend for some of the unregulated species from blends of biodiesel such as formaldehyde, acetaldehyde, ethanol, n-butane however methane reduced upon using these oxygenated fuel blends except methanol, compared to baseline mineral diesel. Nevertheless, no significant changes were observed for sulfur dioxide, iso-butane, n-octane, n-pentane, formic acid, benzene, acetylene and ethylene upon using biodiesel and methanol blends.     

Experimental study of the performances of a modified diesel engine operating in homogeneous charge compression ignition (HCCI) combustion mode versus the original diesel combustion mode

Homogeneous charge compression ignition (HCCI) combustion mode provides very low NO_x and soot emissions; however, it has some challenges associated with hydrocarbon (HC) emissions, fuel consumption, difficult control of start of ignition and bad behaviour to high loads. Cooled exhaust gas recirculation (EGR) is a common way to control in-cylinder NO_x production in diesel and HCCI combustion mode. However EGR has different effects on combustion and emissions, which are difficult to distinguish. This work is intended to characterize an engine that has been modified from the base diesel engine (FL1 906 DEUTZ-DITER) to work in HCCI combustion mode. It shows the experimental results for the modified diesel engine in HCCI combustion mode fueled with commercial diesel fuel compared to the diesel engine mode. An experimental installation, in conjunction with systematic tests to determine the optimum crank angle of fuel injection, has been used to measure the evolution of the cylinder pressure and to get an estimate of the heat release rate from a single-zone numerical model. From these the angle of start of combustion has been obtained. The performances and emissions of HC, CO and the huge reduction of NO_x and smoke emissions of the engine are presented. These results have allowed a deeper analysis of the effects of external EGR on the HCCI operation mode, on some engine design parameters and also on NO_x emission reduction.     

Hydrogen and propane implications for reactivity controlled compression ignition combustion engine running on landfill gas and diesel fuel

A detailed investigation of employing landfill gas together with additives such as hydrogen or propane or both as a primary low reactivity fuel in a reactivity controlled compression ignition combustion of a diesel engine is conducted. A 3401E caterpillar single-cylinder diesel engine with a bathtub piston bowl profile is utilized to execute the study. The engine is operated at various intake pressures of 1.6, 1.9, and 2.2 bar, and runs at a fixed engine speed of 1300 rpm. For verification purposes, the conduct of the present engine running on pure methane as a low reactivity fuel is compared to that of the same engine available in the literature. Next, a numerical simulation is made to assess the performance of the present engine running on landfill gas plus the additives. Based on the obtained results, injecting either hydrogen or propane or a combination of both up to a total amount of 10% by volume to the premixed of landfill gas and air, and advancing diesel fuel injection timing of about 20–30 deg. crank angle, render the landfill gas utilization quite competitive with using methane alone. Applying an enriched landfill gas in a reactivity controlled compression ignition diesel engine, as a power generator, drastically reduces the greenhouse gas emission to the atmosphere. Also, the CO and UHC mole fraction in the exhaust gas can be eliminated by either advancing the start of diesel injection or using hydrogen or propane or both as additives. In addition, utilizing hydrogen or propane or a combination of both with the primary fuel improves the peak pressure to about 16% in comparison with that of landfill gas alone.     

Effect of hythane enrichment on performance,emission and combustion characteristics of an ci engine

Although compression ignition engines have high torque output and thermal efficiency, they emit lots of NO_x and smoke emissions. Moreover, total number and percentage of compression ignition engine powered vehicles in road vehicles have been increasing recent years which is called as dieselisation in EEA term reports. Dieselisation is really hazardous for human life and environment. Therefore, some governments in Europe take action to forbid using diesel engine powered vehicles in city centers. Hydrogen and methane mixture which is named as hythane can be an alternative to restrict this negative situation. For this reason, 90% methane and 10% hydrogen gas mixture was used as additional fuel in diesel engine. According to obtained results, smoke emission was decreased 95.44% at the rate of 50% gaseous fuel at 2100 rpm engine speed. However, increase of THC, CO and NO_x emissions with hythane addition weren't prevented. Using hythane in conventional diesel engines as dual operation mode will be solution to diminish dieselisation problem in near feature.     

Analysis of ignition delay by taking Di-tertiary-butyl peroxide as an additive in a dual fuel diesel engine using hydrogen as a secondary fuel

Ignition delay (ID) is one of the important parameters that make influenced on the combustion process inside the cylinder. This ignition delay affects not only the performances but also the noise and emissions of the engine. In this regards the experiments were conducted on single cylinder 4–stroke compression ignition research diesel engine, power 3.50 kW at constant speed 1500 rpm Kirloskar model TV1 with base fuel as diesel and hydrogen as secondary fuel with and without Di-tertiary-butyl-peroxide (DTBP). Experiments were conducted to measure the ignition delay of the dual fuel diesel (DFD) engine at different load conditions and substitution of diesel by hydrogen with or without DTBP and then it was compared with predicted ID given by Hardenberg-Hase equation and modified Hardenberg-Hase equation.The experimental values of ignition delay were compared with theoretical ignition delay which was predicted on the basis of Hardenberg-Hase equation by considering mean cylinder temperature, pressure, activation energy and cetane number and variations are found in between 6.60% and 21.22%. While, the Hardenberg-Hase equation was modified (by considering variation in activation energy) for DFD engine working on diesel as primary fuel and hydrogen as secondary fuel shows variations 1.20%–11.96%. Furthermore, with DTBP it gives variation up to 18.01%. It was found that ID decreases with increase in percentage of DTBP and hydrogen in air-fuel mixture. This might be due to the cetane improver nature of DTBP, pre-ignition reaction rate and energy release rate of hydrogen fuel. The polytropic index get increased by addition of (Di-tert butyl peroxide) DTBP. Similarly, 5% Di tertiary butyl peroxide reduces Ignition delay.     

Parametric studies for improving the performance of a Jatropha oil-fuelled compression ignition engine

A single cylinder, constant speed, direct injection diesel engine was operated on neat Jatropha oil. Injection timing, injector opening pressure, injection rate and air swirl level were changed to study their influence on performance, emissions and combustion. Results have been compared with neat diesel operation. The injection timing was varied by changing the position of the fuel injection pump with respect to the cam and injection rate was varied by changing the diameter of the plunger of the fuel injection pump. A properly oriented masked inlet valve was employed to enhance the air swirl level. Advancing the injection timing from the base diesel value and increasing the injector opening pressure increase the brake thermal efficiency and reduce HC and smoke emissions significantly. Enhancing the swirl has only a small effect on emissions. The ignition delay with Jatropha oil is always higher than that of diesel under similar conditions. Improved premixed heat release rates were observed with Jatropha oil when the injector opening pressure is enhanced. When the injection timing is retarded with enhanced injection rate, a significant improvement in performance and emissions was noticed. In this case emissions with Jatropha oil are even lower than diesel. At full output, the HC emission level is 532 ppm with Jatropha oil as against 798 ppm with diesel. NO level and smoke with Jatropha oil are, respectively 1162.5 ppm and 2 BSU while they are 1760 ppm and 2.7 BSU with diesel.     

Combustion analysis of preheated crude sunflower oil in an IDI diesel engine

In this study, preheated crude sunflower oil (PCSO) was tested for combustion and emission properties against petroleum based diesel fuel (PBDF) in a naturally aspirated, indirect injection (IDI) engine. The cylinder gas pressure and heat release curves for PCSO at 75 °C were similar to those of PBDF. The ignition delays for the PCSO were longer and the start of injection timing was earlier than for PBDF. The difference in the average brake torque was a decrease of 1.36% for PCSO though this was statistically insignificant. The brake specific fuel consumption increased by almost 5% more or less in proportion to the difference in calorific value, so that the 1.06% increase in thermal efficiency was again statistically insignificant.The emission test results showed that the decreases in CO₂ emissions and smoke opacity 2.05% and 4.66%, respectively; however, this was not statistically significant, though in line with the apparent increase in thermal efficiency. There was a significant 34% improvement in the emissions of unburnt hydrocarbons. Carbon monoxide increased by 1.77% again the result was not statistically significant given the small number of repeat tests.The use of PCSO does not have any negative effects on the engine performance and emissions in short duration engine testing.     

Effect of fuel injection timing and injection pressure on performance in a hydrogen direct injection engine

The in-cylinder hydrogen fuel injection method (diesel engine) induces air during the intake stroke and injects hydrogen gas directly into the cylinder during the compression stroke. Fundamentally, because hydrogen gas does not exist in the intake pipe, backfire, which is the most significant challenge to increasing the torque of the hydrogen port fuel injection engine, does not occur. In this study, using the gasoline fuel injector of a gasoline direct-injection engine for passenger vehicles, hydrogen fuel was injected at high pressures of 5 MPa and 7 MPa into the cylinder, and the effects of the fuel injection timing, including the injection pressure on the output performance and efficiency of the engine, were investigated. Strategies for maximizing engine output performance were analyzed.The fuel injection timing was retarded from before top dead center (BTDC) 350 crank angle degrees (CAD) toward top dead center (TDC). The minimum increase in the best torque ignition timing improved, and the efficiency and excess air ratio increased, resulting in an increase in torque and decrease in NO_x emissions. However, the retardation of the fuel injection timing is limited by an increase in the in-cylinder pressure. By increasing the fuel injection pressure, the torque performance can be improved by further retarding the fuel injection timing or increasing the fuel injection period. The maximum torque of 142.7 Nm is achieved when burning under rich conditions at the stoichiometric air-fuel ratio.