Synthesis of binary Co–Mg–O oxide system and study of its behavior in reduction/oxidation cycling

The nanoscale Co–Mg–O oxide sample (15 wt% in terms of Co₃O₄) was prepared from the corresponding xerogel synthesized by the modified sol-gel method. The hydrolysis of as-prepared Mg(OCH₃)₂ was carried out using the aqueous solution of Co(NO₃)₂ precursor. The CoO_x nanocrystallites of about 10–20 nm in size were shown to be uniformly distributed within the MgO matrix. The reduction of Co–Mg–O in H₂ flow was found to proceed in two separate stages within the temperature ranges of 200–350 °C and 350–600 °C. The prepared binary Co–Mg–O system was demonstrated to possess completely reproducible reduction behavior in the consecutive reduction/reoxidation cycles. The phase composition of the sample exposed to both the reducing and oxidative environment was followed by an in situ X-ray diffraction analysis performed at temperatures of 25, 300, 500 and 700 °C. The determined lattice parameters for MgO (a = 4.219 Å) and Co₃O₄ (a = 8.110 Å) were found to be slightly increased as compared with the values from Powder Diffraction File, so that the formation of joint non-stoichiometric (Mg_1-xCo_x)O and (Co_3-xMg_x)O₄ phases was suggested. The strong chemical interaction of cobalt oxide with MgO matrix was also evidenced by the data of a diffuse reflectance UV–vis spectroscopy.     

Demonstration of a single-stage metal hydride hydrogen compressor composed of BCC V40TiCr alloy

In this study, demonstration of a one-stage metal hydride hydrogen compressor (MH compressor) by using a BCC alloy was performed. It was estimated that V₄₀Ti₂₂Cr₃₈ could compress approximately 1.6 wt% of hydrogen from 1.0 to 10 MPa in 20–140 °C temperature range from equilibrium theory via pressure-composition-isotherm measurements. For demonstration of an actual MH compressor, a kg-scale experimental system was set up; V₄₀Ti₂₂Cr₃₈ (1.4 kg) was introduced into a 1-inch cylindrical vessel with a heat-medium flow tube outside. As a result, 1.0 MPa of hydrogen can be compressed into the hydrogen cylinder at >10 MPa by hydrogen absorption at 10 °C and desorption at 160 °C for 30 min each (1 cycle/h) to achieve a compression rate of 0.23 Nm³/h and indicate the potential of the practical MH compressors by using BCC alloy.     

Turning glycerol surplus into renewable syngas through glycerol steam reforming over a sol-gel Ni–Mo2C-Al2O3 catalyst

In this work, a sol-gel Ni–Mo₂C–Al₂O₃ catalyst is employed for the first time in the glycerol steam reforming for syngas production. Catalyst stability and activity are investigated in the temperature range of 550 °C–700 °C and time on stream up to 30 h. As reaction temperature increases, from 550 °C to 700 °C, H₂ yield boosts from 22% to 60%. The stability test, carried out at milder conditions (600 °C and Gas-Hourly Space-Velocity (GHSV) of 50,000 mL h⁻¹.g_cat⁻¹), shows high catalyst stability, up to 30 h, with final conversion, H₂ yield, and H₂/CO ratio of 95%, 53% and 1.95, respectively. Both virgin and spent catalysts have been characterized by a multitude of techniques, e.g., Atomic-Absorption spectroscopy, Raman spectroscopy, N₂-adsorption-desorption, and Transmission Electron Microscopy (TEM), among others. Regarding the spent catalysts, carbon deposits’ morphology becomes more graphitic as the reaction temperature increases, and the total coke formation is mitigated by increasing reaction temperature and lowering GHSV.     

Novel sonochemical synthesis of Zn2V2O7 nanostructures for electrochemical hydrogen storage

Although utilization of diverse classes of metal oxides as hydrogen storage materials has been reported, but there is still a major need to introduce efficient materials. Herein, mesoporous Zn₂V₂O₇ nanostructures were produced by a new sonochemical method using hydrazine, zinc nitrate, and ammonium vanadate as the starting reagents and then annealed at 700 °C. Prior to annealing, Zn₃V₃O₈ was produced in the presence of ultrasonic waves, whereas in the absence of ultrasonic waves, Zn₂(VO₄)₂ was the major product. In fact, ultrasonic waves interfered with the reaction mechanism and reduced V⁵⁺ to V⁴⁺ and V³⁺. Because of the proper composition and structure of these nanostructures, they were used for electrochemical storage of hydrogen. Storage of over 2899 mAh/g after 20 cycles by flower-like nanostructures revealed their high capability. The results also showed that morphology affects efficiency such that three-dimensional spherical nanostructures had a storage capacity of 2247 mAh/g after 20 cycles.     

A strategy of mid-temperature natural gas based chemical looping reforming for hydrogen production

Steam methane reforming (SMR) needs the reaction heat at a temperature above 800 °C provided by the combustion of natural gas and suffers from adverse environmental impact and the hydrogen separated from other chemicals needs extra energy penalty. In order to avoid the expensive cost and high power consumption caused by capturing CO₂ after combustion in SMR, natural gas Chemical Looping Reforming (CLR) is proposed, where the chemical looping combustion of metal oxides replaced the direct combustion of NG to convert natural gas to hydrogen and carbon dioxide. Although CO₂ can be separated with less energy penalty when combustion, CLR still require higher temperature heat for the hydrogen production and cause the poor sintering of oxygen carriers (OC). Here, we report a high-rate hydrogen production and low-energy penalty of strategy by natural gas chemical-looping process with both metallic oxide reduction and metal oxidation coupled with steam. Fe₃O₄ is employed as an oxygen carrier. Different from the common chemical looping reforming, the double side reactions of both the reduction and oxidization enable to provide the hydrogen in the range of 500–600 °C under the atmospheric pressure. Furthermore, the CO₂ is absorbed and captured with reduction reaction simultaneously.Through the thermodynamic analysis and irreversibility analysis of hydrogen production by natural gas via chemical looping reforming at atmospheric pressure, we provide a possibility of hydrogen production from methane at moderate temperature. The reported results in this paper should be viewed as optimistic due to several idealized assumptions: Considering that the chemical looping reaction is carried out at the equilibrium temperature of 500 °C, and complete CO₂ capture can be achieved. It is assumed that the unreacted methane and hydrogen are completely separated by physical adsorption. This paper may have the potential of saving the natural gas consumption required to produce 1 m³ H₂ and reducing the cost of hydrogen production.     

Effect of ZrO2 on the performance of Co–CeO2 catalysts for hydrogen production from waste-derived synthesis gas using high-temperature water gas shift reaction

In this study, highly active and stable CeO₂, ZrO₂, and Zr_(1-x)Ce_(x)O₂-supported Co catalysts were prepared using the co-precipitation method for the high-temperature water gas shift reaction to produce hydrogen from waste-derived synthesis gas. The physicochemical properties of the catalysts were investigated by carrying out Brunauer-Emmet-Teller, X-ray diffraction, CO-chemisorption, Raman spectroscopy, transmission electron microscopy, X-ray photoelectron spectroscopy, and H₂-temperature-programmed reduction measurements. With an increase in the ZrO₂ content, the surface area and reducibility of the catalysts increased, while the interaction between Co and the support and the dispersion of Co deteriorated. The Co–Zr_0.4Ce_0·6O₂ and Co–Zr_0.6Ce_0·4O₂ catalysts showed higher oxygen storage capacity than that of the others because of the distortion of the CeO₂ structure due to the substitution of Ce⁴⁺ by Zr⁴⁺. The Co–Zr_0.6Ce_0·4O₂ catalyst with high reducibility and oxygen storage capacity exhibited the best catalytic performance and stability among all the catalysts investigated in this study.     

Nickel-loaded red mud catalyst for steam gasification of bamboo sawdust to produce hydrogen-rich syngas

Ni/red mud (RM) catalysts were prepared by wet impregnation and used in the catalytic steam gasification of bamboo sawdust (BS) to produce hydrogen-rich syngas. The system was optimized in terms of the amount of added nickel (10%), reaction temperature (800 °C), and catalyst placement (separately behind the BS). The maximum H₂ yield was 17.3% higher than that using pure RM catalyst and 43.8% higher than that of BS gasification alone, and the H₂/CO ratio in the syngas reached 7.82. This Ni/RM catalyst also retained good activity after six cycles in a double-stage fixed bed reactor. Analysis using X-ray fluorescence, X-ray diffraction, scanning electron microscopy-energy dispersive spectroscopy, and other methods revealed that the interaction of Ni, Fe, and Mg in Ni/RM produced bimetallic compounds containing active sites, such as NiFe₂O₄, MgNiO₂, and NiO. This explains the good catalytic performance in the tar conversion during the gasification process.     

Simulation and optimization of hydrogen production by steam reforming of natural gas for refining and petrochemical demands in Lebanon

Steam reforming of natural gas produces the majority of the world's hydrogen (H₂) and it is considered as a cost-effective method from a product yield and energy consumption point of view. In this work, we present a simulation and an optimization study of an industrial natural gas steam reforming process by using Aspen HYSYS and MATLAB software. All the parameters were optimized to successfully run a complete process including the hydrogen production zone units (reformer reactor, high temperature gas shift reactor HTS and low temperature gas shift reactor LTS) and the purification zone units (absorber and methanator). Optimum production of hydrogen (87,404 MT/year) was obtained by fixing the temperatures in the reformer and the gas shift reactors (HTS & LTS) at 900 °C, 500 °C and 200 °C respectively while maintaining a pressure of 7 atm, and a steam to carbon ratio (S/C) of 4. Moreover, ~99% of the undesired CO₂ and CO gases were removed in the purification zone and a reduction of energy consumption of 77.5% was reached in the heating and cooling units of the process.     

Supercritical water gasification mechanism of polymer-containing oily sludge

In the offshore petroleum industry, polymer-containing oily sludge (PCOS) hinders oil extraction and causes tremendous hazards to the marine ecological environment. In this paper, an effective pretreatment method is proposed to break the adhesive structure of PCOS, and the experiments of supercritical water gasification are carried out under the influencing factors including residence time (5–30 min) and temperature (400–750 °C) in batch reactors. The increase of time and temperature all show great promoting effects on gas production. Polycyclic aromatic hydrocarbons, including naphthalene and phenanthrene, are considered as the main obstacles for a complete gasification. Carbon gasification efficiency (CE) reaches maximum of 95.82% at 750 °C, 23 MPa for 30 min, while naphthalene makes up 70% of the organic compounds in residual liquid products. The highest hydrogen yield of 19.79 (mol H₂/kg of PCOS) is observed in 750 °C for 25 min. A simplified reaction pathway is presented to describe the gaseous products (H₂, CO, CO₂, CH₄). Two intermediates are defined for describing the reaction process bases on the exhaustive study on organic matters in residual liquid products. The results show that the calculated data and the experimental data have a high degree of fit and tar formation reaction is finished within 10 min.     

Effect of introducing manganese as additive on microstructure,hydrogen storage properties and rate limiting step of Ti–Cr alloy

TiCr₂ with adding different amount of Mn (0, 2, 4 and 8 wt.%) alloys have been investigated. All alloys have C14-type main phase (gray color in SEM) and Ti minor phase (dark gray color in SEM). Rietveld fitting results proved that the lattice parameter a and cell volume of C14-type phase decreased with increasing Mn content. The first hydrogenation measurement manifest that all alloys have best activation properties and could be activated without any prior heat treatment and hydrogen exposure. However, introducing Mn led to the decrease of the first hydrogen absorption rate of TiCr₂ alloy, which may be due to the decrease of cell volume of C14-type main phase. The first hydrogenation properties at low temperature and effect of air exposure of the alloy were discussed. The results showed that the maximum hydrogen absorption capacity at 0 °C was obviously higher than that at room temperature. In addition, TiCr₂ alloy doped with minor amounts of Mn after long-time air exposure showed better hydrogenation performance. This may be due to the Mn additive acting as a deoxidizer. Finally, the first hydrogenation kinetic mechanisms of all alloys at different temperature were also studied by using the rate limiting step.     

Effect of physical activation/surface functional groups on wettability and electrochemical performance of carbon/activated carbon aerogels based electrode materials for electrochemical capacitors

Polymeric carbon/activated carbon aerogels were synthesized through sol-gel polycondensation reaction followed by the carbonization at 800 °C under Argon (Ar) atmosphere and subsequent physical activation under CO₂ environment at different temperatures with different degrees of burn-off. Significant increase in BET specific surface area (SSA) from 537 to 1775 m²g⁻¹ and pore volume from 0.24 to 0.94 cm³g⁻¹ was observed after physical activation while the pore size remained constant (around 2 nm). Morphological characterization of the carbon and activated carbons was conducted using X-ray diffraction (XRD) and Raman spectroscopy. Fourier-transform infrared spectroscopy (FTIR) and X-ray photoelectron spectroscopy (XPS) were used to investigate the effect of thermal treatment (surface cleaning) on the chemical composition of carbon samples.Cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS) were used to analyse the capacitive and resistive behaviour of non-activated/activated/and surface cleaned activated carbons employed as electroactive material in a two electrode symmetrical electrochemical capacitor (EC) cell with 6 M KOH solution used as the electrolyte.CV measurements showed improved specific capacitance (SC) of 197 Fg⁻¹ for activated carbon as compared to the SC of 136 Fg⁻¹ when non-activated carbon was used as electroactive material at a scan rate of 5 mVs⁻¹. Reduction in SC from 197 Fg⁻¹ to 163 Fg⁻¹ was witnessed after surface cleaning at elevated temperatures due to the reduction of surface oxygen function groups.The result of EIS measurements showed low internal resistance for all carbon samples indicating that the polymeric carbons possess a highly conductive three dimensional crosslinked structure. Because of their preferred properties such as controlled porosity, exceptionally high specific surface area, high conductivity and desirable capacitive behaviour, these materials have shown potential to be adopted as electrode materials in electrochemical capacitors.     

Detonation propagation characteristics of H2/O2/AR in multi-angle bifurcation tubes

The propagation characteristics of the detonation wave in the bifurcated tube with the angular variation range of 30°–90° are simulated with 25% AR as dilution gas for H₂/O₂ mixture fuel at chemical equivalence ratio using the solver DCRFoam built on the OpenFOAM platform. The diffraction and reflection phenomena of detonation waves passing through bifurcation tubes with different angles are studied and analyzed. The results show that the distance from regular reflection to Mach reflection increases with the increase of the bifurcation angle so that after one reflection, the detonation forms three reflection forms with the angle of the different bifurcation tubes. After the first reflection, the detonation waves are more likely to induce the formation of transverse waves in the low-angle bifurcation tube. The lowest collision pressure after the detonation collides with the upper wall to form a secondary reflection occurs in the bifurcation tube between 50° and 60°.     

Assessment of ammonia as energy carrier in the use with reversible solid oxide cells

Ammonia represents one of the most promising potential solutions as energy vector and hydrogen carrier, having a higher potential to transport energy than hydrogen itself in a pressurized form. Furthermore, solid oxide fuel cells (SOFCs) can directly be fed with ammonia, thus allowing for immediate electrical power and heat generation. This paper deals with the analysis of the dynamic behavior of commercial SOFCs when fueled with ammonia. Several measurements at different temperatures have been performed and performances are compared with hydrogen and a stoichiometrically equivalent mixture of H₂ and N₂ (3:1 M ratio). Higher temperature led to smaller drops in voltage for both fuels, thus providing higher efficiencies. Ammonia resulted slightly more performant (48% at 760 °C) than hydrogen (45% at 760 °C), in short stack tests. Moreover, different ammonia-to-air ratios have been investigated and the stack area-specific resistance has been studied in detail by comparing numerical modeling predictions and experimental values.     

Preparation and improvement of nickel catalyst supported ordered mesoporous spherical silica for thermocatalytic decomposition of methane

The thermocatalytic alteration of CH₄ into highly pure hydrogen and filaments of carbon was investigated on a series of Ni-catalysts with various contents (25, 40, 55, and 70 wt%) supported mesoporous spherical SiO₂. The silica with ordered structure and high specific surface area (1136 m²/g) was synthesized using the Stöber technique with TEOS as a silica precursor and CTAB as the template in a simple synthesis system of aqueous-phase. This technique led to the preparation of mesoporous spherical silica. The prepared samples were characterized using BET, TPR, XRD, TPO, and SEM analyses. The prepared catalysts with different nickel loading showed the BET surface area ranging from 225.0 to 725.7 m²/g. These results indicated that an increase in nickel content decreases the surface area and leads to a subsequent collapse of a pore structure. SEM analysis confirmed a spherical nanostructure of catalysts and revealed that with the increase in loading of Ni, the particle size enlarged, because of the agglomeration of the particles. The results implied that the high methane conversion of 54% obtained over the 55 wt% Ni/SiO₂ at 575 °C and this sample had higher stability at lower reaction temperature than the other prepared catalysts, slowly deactivation was observed for this catalyst at a period of 300 min of time on stream.     

Steam reforming of acetic acid for hydrogenproduction: Catalytic performances of Ni and Co supported on Ce0·75Zr0·25O2 catalysts

The catalytic steam reforming of acetic acid over both Ni/ and Co/Ce_0·75Zr_0·25O₂ (CZO) catalysts in the temperature range of 450–650 °C and steam-to-carbon molar ratios of 3–9 was studied. It was found that the complete acetic acid conversion was achieved for all the conditions investigated. Nevertheless, the C–C bond cleavage conversion was attained less than the acetic acid conversion at a given condition due to carbon deposition on the catalyst. However, hydrogen yield was obtained in the same trend as C–C bond cleavage conversion as well. The results revealed that the CZO as an active support prefers to promote the ketonization reaction to the C-C bond cleavage reaction at a lower temperature, and vice versa at a higher temperature. The Ni/CZO catalyst exhibits higher C–C bond cleavage conversion than the Co/CZO catalyst particularly at 650 °C whereas the Co/CZO catalyst is more active for ketonization reaction at low temperatures. However, as an increase in reaction temperature, the Co/CZO catalyst promotes ketonization reaction more pronouncedly toward aldol-condensation reaction thus giving rise to the carbon deposition. The results deduced from the effect of space velocity on the activity and product distribution suggested that the steam reforming of acetic acid over Ni/CZO catalyst is dominated by decomposition of acetic acid, while that of Co/CZO catalyst by ketonization reaction.     

System optimization for effective hydrogen production via anaerobic digestion and biogas steam reforming

To construct a system for the effective hydrogen production from food waste, the conditions of anaerobic digestion and biogas reforming have been investigated and optimized. The type of agitator and reactor shape affect the performance of anaerobic digestion reactors. Reactors with a cubical shape and hydrofoil agitator exhibit high performance due to the enhanced axial flow and turbulence as confirmed by simulation of computational fluid dynamics. The stability of an optimized anaerobic digestion reactor has been tested for 60 days. As a result, 84 L of biogas is produced from 1 kg of food waste. Reaction conditions, such as reaction temperature and steam/methane ratio, affect the biogas steam reforming reaction. The reactant conversions, product yields, and hydrogen production are influenced by reaction conditions. The optimized reaction conditions include a reaction temperature of 700 °C and H₂O/CH₄ ratio of 1.0. Under these conditions, hydrogen can be produced via steam reforming of biogas generated from a two-stage anaerobic digestion reactor for 25 h without significant deactivation and fluctuation.     

HRT control as a strategy to enhance continuous hydrogen production from sugarcane juice under mesophilic and thermophilic conditions in AFBRs

The objective of this study was to evaluate the effects of hydraulic retention time (HRT) (8–1 h) on H₂ production from sugarcane juice (5000 mg COD L⁻¹) in mesophilic (30 °C, AFBR-30) and thermophilic (55 °C, AFBR-55) anaerobic fluidized bed reactors (AFBRs). At HRTs of 8 and 1 h in AFBR-30, the H₂ production rates were 60 and 116 mL H₂ h⁻¹ L⁻¹, the hydrogen yields were 0.60 and 0.10 mol H₂ mol⁻¹ hexose, and the highest bacterial diversities were 2.47 and 2.34, respectively. In AFBR-55, the decrease in the HRT from 8 to 1 h increased the hydrogen production rate to 501 mL H₂ h⁻¹ L⁻¹ at the HRT of 1 h. The maximum hydrogen yield of 1.52 mol H₂ mol⁻¹ hexose was observed at the HRT of 2 h and was associated with the lowest bacterial diversity (0.92) and highest bacterial dominance (0.52).     

Hydrofluoroolefin-based mixed refrigerant for enhanced performance of hydrogen liquefaction process

Hydrogen has the highest gravimetric energy density of all fuels; however, it has a low volumetric energy density, unfavorable for storage and transportation. Hydrogen is usually liquefied to meet the bulk transportation needs. The exothermic interconversion of its spin isomers is an additional activity to an already energy-intensive process. The most significant temperature drop occurs in the precooling cycle (between ?150 °C and up to ?180 °C) and consumes more than 50% of the required energy. To reduce the energy consumption and improve the exergy efficiency of the hydrogen liquefaction process, a new high-boiling component, Hydrofluoroolefin (HFO-1234yf), is added to the precooled mixed refrigerant. As a result, the specific energy consumption of precooling cycle reduces by 41.8%, from 10.15 kWh/kg_LH2 to 5.90 kWh/kg_LH2, for the overall process. The exergy efficiency of the proposed case increases by 43.7%; however, the total equipment cost is also the highest. The inflated cost is primarily due to the added ortho-to-para hydrogen conversion reactor, boosting the para-hydrogen concentration. From the perspective of bulk storage and transportation of liquid hydrogen, the simplicity of design and low energy consumption build a convincing case for considering the commercialization of the process.     

Effect of B-site Al substitution on hydrogen production of La0.4Sr0.6Mn1-xAlx (x=0.4, 0.5 and 0.6) perovskite oxides

Thermochemical water splitting using perovskite oxides as redox materials is one of the important way to use solar energy to produce green hydrogen. Thus, it is hence important to discover new materials that can be used for this purpose. In this regard, we focused on Al-substituted La_0.4Sr_0.6Mn_1-xAl_xO₃ (x = 0.4, 0.5 and 0.6) perovskite oxides, namely as La_0.4Sr_0.6Mn_0.6Al_0.4 (LSMA4664), La_0.4Sr_0.6Mn_0.5Al_0.5 (LSMA4655), and La_0.4Sr_0.6Mn_0.4Al_0.6 (LSMA4646) which have been successfully synthesized. Herein, synthesized LSMA4664, LSMA4655, and LSMA4646 were subjected to three consecutive thermochemical cycles in order to determine their oxygen capacity, hydrogen capacity, re-oxidation capability and structural stability following three cycles. Thermochemical cycles were carried out at 1400 °C for reduction and 800 °C for the oxidation reaction. LSMA4646 exhibited the highest O₂ production capacity with 275 μmol/g among the other perovskites employed in the study. Moreover, LSMA4646 has also the highest H₂ production, 144 μmol/g, with 90% of re-oxidation capability by the end of three thermochemical water splitting cycles. On the other hand, LSMA4664 has the lowest H₂ production and only kept approximately one-third of its hydrogen production capacity by the end of cycles. Thus, the current study provides insight that the increase in the Al-substitution enhances both oxygen and hydrogen production capacity. Besides, increasing the Al amount increases the structural stability during the redox reactions, the re-oxidation capability was also increased from 38% to 89% after thermochemical cycles.     

The role of oxygen vacancies in the CO2 methanation employing Ni/ZrO2 doped with Ca

The Ni/ZrO₂ catalyst doped with Ca and Ni/ZrO₂ were employed in the CO₂ methanation, a reaction which will possibly be used for storing intermittent energy in the future. The catalysts were characterized by X-ray photoelectron spectroscopy (XPS, reduction in situ), X-ray diffraction (XRD, reduction in situ and Rietveld refinement), electron paramagnetic resonance (EPR), temperature-programmed surface reaction, cyclohexane dehydrogenation model reaction, temperature-programmed desorption of CO₂ and chemical analysis. The catalytic behavior of these catalysts in the CO₂ methanation was analyzed employing a conventional catalytic test. Adding Ca to Ni/ZrO₂, the metallic surface area did not change whereas the CO₂ consumption rate almost tripled. The XRD, XPS and EPR analyses showed that Ca⁺² but also some Ni²⁺ are on the ZrO₂ surface lattice of the Ni/CaZrO₂ catalyst. These cations form pairs which are composed of oxygen vacancies and coordinatively unsaturated sites (cus). By increasing the number of these pairs, the CO₂ methanation rate increases. Moreover, the number of active sites of the CO₂ methanation rate limiting step (CO and/or formate species decomposition, rls) is enhanced as well, showing that the rls occurs on the vacancies-cus sites pairs.