Experimental study of the performances of a modified diesel engine operating in homogeneous charge compression ignition (HCCI) combustion mode versus the original diesel combustion mode

Homogeneous charge compression ignition (HCCI) combustion mode provides very low NO_x and soot emissions; however, it has some challenges associated with hydrocarbon (HC) emissions, fuel consumption, difficult control of start of ignition and bad behaviour to high loads. Cooled exhaust gas recirculation (EGR) is a common way to control in-cylinder NO_x production in diesel and HCCI combustion mode. However EGR has different effects on combustion and emissions, which are difficult to distinguish. This work is intended to characterize an engine that has been modified from the base diesel engine (FL1 906 DEUTZ-DITER) to work in HCCI combustion mode. It shows the experimental results for the modified diesel engine in HCCI combustion mode fueled with commercial diesel fuel compared to the diesel engine mode. An experimental installation, in conjunction with systematic tests to determine the optimum crank angle of fuel injection, has been used to measure the evolution of the cylinder pressure and to get an estimate of the heat release rate from a single-zone numerical model. From these the angle of start of combustion has been obtained. The performances and emissions of HC, CO and the huge reduction of NO_x and smoke emissions of the engine are presented. These results have allowed a deeper analysis of the effects of external EGR on the HCCI operation mode, on some engine design parameters and also on NO_x emission reduction.     

Investigation on emission characteristics of alcohol biodiesel blended diesel engine

The present study analyzes the emission pattern of Decanol combined Jatropha biodiesel (JBD100) fueled diesel engine and compared with conventional diesel fuel (D100). Experiments were conducted in a single-cylinder, 4-stroke naturally aspirated diesel engine with an eddy current dynamometer at a constant speed of 1800 rpm. Modified fuel was prepared using a mechanical agitator, in which the Decanol concentration was varied from 10 to 20% to JBD100. The physicochemical properties of Decanol combined biodiesel are within ASTM limits. JBD100 promotes a lower level of carbon monoxide (CO) hydrocarbon (HC), and smoke emissions with notable increases in NO_x and carbon dioxide (CO₂) emissions. An inclusion of 20% Decanol in JBD100 reduces the NO_x, Smoke, CO, and HC emission by 7.4%, 4.4%, 5.7%, and 5.9%, respectively, under full brake power.     

The Influence of Hydrogen Induction on The Characteristics of a CI Engine Fueled with Blend of Camphor Oil and Diesel with Diethyl Ether Additive

This article investigates the effect of hydrogen induction on the characteristics of a CI engine fueled with the blend of camphor oil and diesel, along with diethyl ether (DEE) as an additive. The fuel sample was prepared by mixing 70% camphor oil with 30% diesel (C7D3) on a volume basis and then tested with 4 LPM (C7D3H4), 6 LPM (C7D3H6), and 8 LPM (C7D3H8) of hydrogen induction on the engine intake manifold. DEE was mixed at 10% and 20% with 90% and 80% of C7D3 on a volume basis and evaluated with 8 LPM of hydrogen induction; the resulting mixtures were designated as C7D3H8E10 and C7D3H8E20. The maximum thermal efficiency for C7D3H8E10 is 32.97%, with a minimum BSEC of 10.91 MJ/kgh, CO of 5.22 g/kWh, HC of 0.206 g/kWh, and smoke opacity of 39.6%. Hydrogen induction and increasing the quantity of hydrogen from 4 lpm to 8 lpm in the manifold increases the thermal efficiency to 32.63%. Further, it reduces the BSEC to 11.03 MJ/kgh, CO of 5.65 g/kWh, HC of 0.222 g/kW, and smoke opacity of 46.3%. NO_x emissions were found to increase while increasing the hydrogen induction and with a 10% DEE addition to the C7D3 fuel. Further, raising the DEE from a 10%–20% ratio reduces the thermal efficiency and increases the BSEC, CO, HC, and smoke emissions. Overall, C7D3 in CI engines with 10% more DEE and hydrogen induction up to 8 LPM may be used efficiently.     

Physico-chemical properties of ethanol–diesel blend fuel and its effect on performance and emissions of diesel engines

The effects of different ethanol–diesel blended fuels on the performance and emissions of diesel engines have been evaluated experimentally and compared in this paper. The purpose of this project is to find the optimum percentage of ethanol that gives simultaneously better performance and lower emissions. The experiments were conducted on a water-cooled single-cylinder Direct Injection (DI) diesel engine using 0% (neat diesel fuel), 5% (E5–D), 10% (E10–D), 15% (E15–D), and 20% (E20–D) ethanol–diesel blended fuels. With the same rated power for different blended fuels and pure diesel fuel, the engine performance parameters (including power, torque, fuel consumption, and exhaust temperature) and exhaust emissions [Bosch smoke number, CO, NO_x, total hydrocarbon (THC)] were measured. The results indicate that: the brake specific fuel consumption and brake thermal efficiency increased with an increase of ethanol contents in the blended fuel at overall operating conditions; smoke emissions decreased with ethanol–diesel blended fuel, especially with E10–D and E15–D. CO and NO_x emissions reduced for ethanol–diesel blends, but THC increased significantly when compared to neat diesel fuel.     

Investigation on combustion and emission characteristics of hydrogen-enriched dual-fuel engine operated under waste frying oil biodiesel

Using nonedible waste frying oil (WFO) as biodiesel and hydrogen in the mix composition may partly replace significant quantities of diesel fuel and help reduce fossil fuel reliance. The combination of diesel fuel, waste-fired biodiesel, and hydrogen gas can improve the performance, combustion, and emissions of single-fuel and dual-fuel diesel engines. This may lead to a novel alternative fuel mix pattern and modification for diesel engines, which is the research gap. Although there has been some research on waste-fired biodiesel and hydrogen gas-powered dual-fuel engines with the goal of partly replacing fossil fuels to a larger degree, there has been very little progress in this area. As a result, the current research effort focuses on using diesel fuel (100%, 30%, and 60%), waste-fired biodiesel (at 100%, 70%, and 40%), and hydrogen gas as fuel sources (5 and 10 liters per minute [LPM]). According to the current experiment, it was perceived in both dual-fuel and single-fuel modes. Under duel-fuel mode, the engine results for WFOB70D30 + H10 fuel blend had higher 4.2% (brake thermal efficiency [BTE]), 19.72% (oxides of nitrogen [NO_x]), and 9.09% (ignition delay [ID]) with a minimal range of (in-cylinder pressure, MFB, volumetric efficiency and heat release rate [HRR]) and a dropped rate of 4.34% (brake-specific energy consumption [BSEC]), 33.33% (carbon monoxide [CO]), 39.28% (hydrocarbons [HC]), 9.43% (smoke), and 6.97% (combustion duration [CD]) related to diesel fuel at peak load. However, single-fuel powered diesel engines provide minimal performance for the WFOB40D60 fuel blend with (11.32% lower BTE and 2.04% higher BSEC) and minimal rate of combustion (lower cylinder pressure, 2.12% minimal CD, 14.72% higher ID, minimal HRR combustion, volumetric efficiency, and MFB). Emitted fewer emissions (9.09% less CO, 4.87% less HC, 0.92% higher NO_x, and 1.69% more smoke) than diesel fuel at peak load. Therefore, it was concluded that adding 10 LPM of hydrogen gas to the biodiesel under a dual-fuel condition leads to better combustion, better performance, and less pollution than the single-fuel mode of operation.     

A new diesel oxygenate additive and its effects on engine combustion and emissions

2-methoxyethyl acetate (MEA) can be used to decrease exhaust smoke as a new oxygenated additive of diesel. Several fuel blends which containing 10%, 15% and 20% MEA were prepared. The effects of MEA on engine’s power, fuel economy, emissions and combustion characteristics were studied on a single cylinder DI diesel engine. Under the same speed and load conditions, the maximum cylinder pressure decreases when fueled with the blends, while the ignition delays and the combustion duration becomes shorter. The engine emissions of smoke, HC and CO are reduced when MEA is added in diesel. However, MEA has a little effect on NO_x emissions. When fueled with MEA15, the coefficient of light absorption of smoke opacimeter decreases about 50% with expense of 5% power, and the engine’s thermal efficiency increases about 2%.     

Study of low emission homogeneous charge compression ignition (HCCI) engine using combined internal and external exhaust gas recirculation (EGR)

This paper focuses on the effects of internal and cooled external exhaust gas recirculation (EGR) on the combustion and emission performance of diesel fuel homogeneous charge compression ignition (HCCI). The use of fuel injection before the top center (TC) of an exhaust stroke and the negative valve overlap (NVO) to form the homogeneous mixture achieves low NO_x and smoke emissions HCCI. Internal and external EGR are combined to control the combustion. Internal exhaust gas recirculation (IEGR) benefits to form a homogeneous mixture and reduces smoke emission further, but lower the high load limits of HCCI. Cooled external EGR can delay the start of combustion (SOC) effectively, which is very useful for high cetane fuel (diesel) HCCI because these fuels can easily self-ignited, making the SOC earlier. External EGR can avoid the knock combustion of HCCI at high load, which means it can expand the high load limit. HCCI maintains low smoke emission at various EGR rates and various loads compared with a conventional diesel engine because there are no fuel-rich volumes in the cylinder.     

Effects of Fischer-Tropsch diesel fuel on combustion and emissions of direct injection diesel engine

Effects of Fischer-Tropsch (F-T) diesel fuel on the combustion and emission characteristics of a single-cylinder direct injection diesel engine under different fuel delivery advance angles were investigated. The experimental results show that F-T diesel fuel exhibits shorter ignition delay, lower peak values of premixed burning rate, lower combustion pressure and pressure rise rate, and higher peak value of diffusion burning rate than conventional diesel fuel when the engine remains unmodified. In addition, the unmodified engine with F-T diesel fuel has lower brake specific fuel consumption and higher effective thermal efficiency, and presents lower HC, CO, NO _x and smoke emissions than conventional diesel fuel. When fuel delivery advance angle is retarded by 3 crank angle degrees, the combustion duration is obviously shortened; the peak values of premixed burning rate, the combustion pressure and pressure rise rate are further reduced; and the peak value of diffusion burning rate is further increased for F-T diesel fuel operation. Moreover, the retardation of fuel delivery advance angle results in a further significant reduction in NO _x emissions with no penalty on specific fuel consumption and with much less penalty on HC, CO and smoke emissions. __________ Translated from Chinese Internal Combustion Engine Engineering, 2007, 28(2): 19–23 [译自: 内燃机工程]     

Application of exhaust gas fuel reforming in diesel and homogeneous charge compression ignition (HCCI) engines fuelled with biofuels

This paper documents the application of exhaust gas fuel reforming of two alternative fuels, biodiesel and bioethanol, in internal combustion engines. The exhaust gas fuel reforming process is a method of on-board production of hydrogen-rich gas by catalytic reaction of fuel and engine exhaust gas. The benefits of exhaust gas fuel reforming have been demonstrated by adding simulated reformed gas to a diesel engine fuelled by a mixture of 50% ultra low sulphur diesel (ULSD) and 50% rapeseed methyl ester (RME) as well as to a homogeneous charge compression ignition (HCCI) engine fuelled by bioethanol. In the case of the biodiesel fuelled engine, a reduction of NO_x emissions was achieved without considerable smoke increase. In the case of the bioethanol fuelled HCCI engine, the engine tolerance to exhaust gas recirculation (EGR) was extended and hence the typically high pressure rise rates of HCCI engines, associated with intense combustion noise, were reduced.     

Optimization of port injection of n-decanol in a PCCI engine using response surface methodology

This work aims to define the optimum n-decanol fraction in the inlet port and the corresponding engine load for the better emissions and performance characteristics of a partially premixed charged compression ignition (PCCI) engine by response surface methodology (RSM). The numerical model based on multi-linear regression was established using experimental data. For this, the influence of various proportions of n-decanol through intake port including 10%, 20%, 30%, and 40% were experimentally investigated besides the primary injection of neem oil biodiesel in the volumetric ratio of 80% diesel and 20% neem biodiesel, namely NB20. The optimization using RSM is exploited to capitalize the brake thermal efficiency (BTE) and diminish the emissions including oxides of nitrogen (NO_x), carbon monoxide (CO) emission, smoke opacity, and hydrocarbon (HC) emission. The n-decanol fraction in the port injection of 31.43% and the engine load in terms of brake power of 2.950 kW were found to be optimum parameters with the maximum desirability of 0.752. The optimal responses for brake-specific fuel consumption (BSFC), BTE, CO, HC, smoke, and NO_x under these operating conditions were found to be 0.305 kg/kWh, 28.8%, 0.145%, 19.61%, 54.85 ppm, and 837.7 ppm, respectively. Likewise, the correlation coefficient R² values for BSFC, BTE, CO, HC, smoke and NO_x have been found to be 99.85%, 99.95%, 93.58%, 90.32%, 99.97%, and 99.93%, respectively. According to the study's findings, the RSM is a realistic method for calculating and enhancing a diesel engine's emission and performance values operating in PCCI mode and using n-decanol and NB20 as fuels.     

推进特性试验下生物乳化柴油对柴油机性能的影响

在柴油机上进行柴油、三种生物乳化柴油(E10、E15和E20)和生物柴油的推进特性试验,就其燃烧特性、动力性、经济性及常规排放特性进行对比。试验结果显示:高转速时,生物乳化柴油的缸内燃烧压力和放热率略低于柴油,缸内燃烧温度有所降低;动力性相比柴油略有下降,仅E10的燃油消耗率比柴油低,B100最高;烟度和NOx排放均有显著降低,且随水和丁醇掺混比例增加而降低; CO和HC排放与柴油基本无差别,整体增加不多。表明:生物乳化柴油作为替代燃料能保证柴油机运行的稳定性,可同时降低柴油机的烟度和NOx排放,具有良好的环境效益和经济效益。     

Influence of advanced injection timing on the performance and emissions of CI engine fueled with ethanol‐blended diesel fuel

Ethanol has been considered as an alternative fuel for diesel engines. On the other hand, injection timing is a major parameter that sensitively affects the engine performance and emissions. Therefore, in this study, the influence of advanced injection timing on the engine performance and exhaust emissions of a single cylinder, naturally aspirated, four stroke, direct injection diesel engine has been experimentally investigated when using ethanol‐blended diesel fuel from 0 to 15% with an increment of 5%. The original injection timing of the engine is 27° crank angle (CA) before top dead center (BTDC). The tests were conducted at three different injection timings (27, 30 and 33° CA BTDC) for 30 Nm constant load at 1800 rpm. The experimental results showed that brake‐specific energy consumption (BSEC), brake‐specific fuel consumption (BSFC), NO_x and CO₂ emissions increased as brake‐thermal efficiency (BTE), smoke, CO and HC emissions decreased with increasing amount of ethanol in the fuel mixture. Comparing the results with those of original injection timing, NO_x emissions increased and smoke, HC and CO emissions decreased for all test fuels at the advanced injection timings. For BSEC, BSFC and BTE, advanced injection timings gave negative results for all test conditions. Copyright © 2008 John Wiley & Sons, Ltd.     

Engine performance and emissions of a diesel engine operating on diesel-RME (rapeseed methyl ester) blends with EGR (exhaust gas recirculation)

The effects of biodiesel (rapeseed methyl ester, RME) and different diesel/RME blends on the diesel engine NO_x emissions, smoke, fuel consumption, engine efficiency, cylinder pressure and net heat release rate are analysed and presented. The combustion of RME as pure fuel or blended with diesel in an unmodified engine results in advanced combustion, reduced ignition delay and increased heat release rate in the initial uncontrolled premixed combustion phase. The increased in-cylinder pressure and temperature lead to increased NO_x emissions while the more advanced combustion assists in the reduction of smoke compared to pure diesel combustion. The lower calorific value of RME results in increased fuel consumption but the engine thermal efficiency is not affected significantly. When similar percentages (% by volume) of exhaust gas recirculation (EGR) are used in the cases of diesel and RME, NO_x emissions are reduced to similar values, but the smoke emissions are significantly lower in the case of RME. The retardation of the injection timing in the case of pure RME and 50/50 (by volume) blend with diesel results in further reduction of NO_x at a cost of small increases of smoke and fuel consumption.     

Effect of different types of fuels tested in a gasoline engine on engine performance and emissions

In this study, three different fuels named G100 (pure gasoline), E20 (volume 20% ethanol and 80% gasoline blend) and ES20 (20% sodium borohydride added ethanol solution and 80% gasoline) were used to test in a gasoline engine. First of all, G100 fuel, E20 and ES20 blended fuels, respectively, were tested in a gasoline engine and the effects of fuels on engine performance and exhaust emissions were investigated experimentally. Experiments were carried out at full load and at five different engine speeds ranging from 1400 to 3000 rpm, and engine performance and exhaust emission values were determined for each test fuel. When the test results of the engine operated with E20 and ES20 blended fuels are compared with the test results of the engine operated with gasoline; engine torque of E20 blended fuel increased by 1.87% compared to pure gasoline, while engine torque of ES20 blended fuel decreased by 1.64%. However, the engine power of E20 and ES20 blended fuels decreased by 2.02% and 5.10%, respectively, compared to the power of pure gasoline engine, while their specific fuel consumption increased by 5.02% and 6.57%, respectively, compared to pure gasoline fueled engine. On the other hand, CO and HC emissions of the engine operated with E20 and ES20 blended fuels decreased compared to the pure gasoline engine, while CO₂ and NO_x emissions increased.     

Effect of exhaust gas recirculation on diesel engine nitrogen oxide reduction operating with jojoba methyl ester

Jojoba methyl ester (JME) has been used as a renewable fuel in numerous studies evaluating its potential use in diesel engines. These studies showed that this fuel is good gas oil substitute but an increase in the nitrogenous oxides emissions was observed at all operating conditions. The aim of this study mainly was to quantify the efficiency of exhaust gas recirculation (EGR) when using JME fuel in a fully instrumented, two-cylinder, naturally aspirated, four-stroke direct injection diesel engine. The tests were carried out in three sections. Firstly, the measured performance and exhaust emissions of the diesel engine operating with diesel fuel and JME at various speeds under full load are determined and compared. Secondly, tests were performed at constant speed with two loads to investigate the EGR effect on engine performance and exhaust emissions including nitrogenous oxides (NO_x), carbon monoxide (CO), unburned hydrocarbons (HC) and exhaust gas temperatures. Thirdly, the effect of cooled EGR with high ratio at full load on engine performance and emissions was examined. The results showed that EGR is an effective technique for reducing NO_x emissions with JME fuel especially in light-duty diesel engines. With the application of the EGR method, the CO and HC concentration in the engine-out emissions increased. For all operating conditions, a better trade-off between HC, CO and NO_x emissions can be attained within a limited EGR rate of 5–15% with very little economy penalty.     

Influence of pentanol and dimethyl ether blending with diesel on the combustion performance and emission characteristics in a compression ignition engine under low temperature combustion mode

Dimethyl ether (DME) and n-pentanol can be derived from non-food based biomass feedstock without unsettling food supplies and thus attract increasing attention as promising alternative fuels, yet some of their unique fuel properties different from diesel may significantly affect engine operation and thus limit their direct usage in diesel engines. In this study, the influence of n-pentanol, DME and diesel blends on the combustion performance and emission characteristics of a diesel engine under low-temperature combustion (LTC) mode was evaluated at various engine loads (0.2–0.8 MPa BMEP) and two Exhaust Gas Recirculation (EGR) levels (15% and 30%). Three test blends were prepared by adding different proportions of DME and n-pentanol in baseline diesel and termed as D85DM15, D65P35, and D60DM20P20 respectively. The results showed that particulate matter (PM) mass and size-resolved PM number concentration were lower for D85DM15 and D65P35 and the least for D60DM20P20 compared with neat diesel. D60DM20P20 turned out to generate the lowest NO_x emissions among the test blends at high engine load, and it further reduced by approximately 56% and 32% at low and medium loads respectively. It was found that the combination of medium EGR (15%) level and D60DM20P20 blend could generate the lowest NO_x and PM emissions among the tested oxygenated blends with a slight decrease in engine performance. THC and CO emissions were higher for oxygenated blends than baseline diesel and the addition of EGR further exacerbated these gaseous emissions. This study demonstrated a great potential of n-pentanol, DME and diesel (D60DM20P20) blend in compression ignition engines with optimum combustion and emission characteristics under low temperature combustion mode, yet long term durability and commercial viability have not been considered.     

Emission characteristics of a turbocharged diesel engine fueled with gas-to-liquids

Emission characteristics of a turbocharged, intercooled, heavy-duty diesel engine operating on neat gas-to-liquids (GTL) and blends of GTL with conventional diesel were investigated and a comparison was made with those of diesel fuel. The results show that nitrogen oxides (NO _x ), smoke, and particulate matter (PM) emissions can be decreased when operating on GTL and diesel-GTL blends. Engine emissions decrease with an increase of GTL fraction in the blends. Compared with diesel fuel, an engine operating on GTL can reduce NO _x , PM, carbon monoxide (CO), and hydrocarbon (HC) by 23.7%, 27.6%, 16.6% and 12.9% in ECE R49 13-mode procedure, respectively. Engine speed and load have great influences on emissions when operating on diesel-GTL blends and diesel fuel in the turbocharged diesel engine. The study indicates that GTL is a promising alternative fuel for diesel engines to reduce emissions. Translated from Transactions of CSICE, 2006, 24(6): 489–493 [译自: 内燃机学报]     

柴油甲醇组合燃烧对机车柴油机排放性能的影响

对一台应用于机车的中速大型柴油机,按照柴油/甲醇组合燃烧(DMCC)的要求,进行了相应的改造,以探究DMCC燃烧模式对其排放性能的影响。结果表明:在800 r/min@9 600 N·m工况下,掺烧甲醇后,NO_x比排放大幅降低,但过分提高甲醇替代率,则NO_x比排放会有所升高;CO₂比排放、燃料费用随甲醇替代率的升高而降低;当量油耗则先随甲醇的替代率提高而升高,随后降低;HC比排放随甲醇替代率提高有所升高。相比于原机,在800 r/min、9 600 N·m、-4° ATDC、35.9%替代率工况, NO_x比排放仅为3.15 g/(kW·h),最大降幅达到56.5%;DMCC模式,640 r/min@6 850 N·m工况下,随着供油提前角的推迟,NO_x、HC比排放降低,排气温度逐渐升高;中等替代率下最低油耗对应的供油提前角推迟,高替代率下供油提前角提前。     

Study of methane enrichment in a biogas fuelled HCCI engine

Biogas has been a promising alternative fuel for IC engines. However, its CO₂ content reduces calorific value and ignitability. The CO₂ fraction of raw biogas can be separated out by various techniques, which are collectively called methane enrichment. The present study explores the effect of methane enrichment on the output parameters of a Homogeneous Charge Compression Ignition (HCCI) engine. A single cylinder CI engine is altered for this purpose. Biogas (CH₄ + CO₂) is supplied along with air. Diethyl Ether (DEE) is used as the secondary fuel to initiate auto-ignition. The effects of injecting DEE at the inlet port and upstream in the intake manifold are also compared. Performance, emission and combustion characteristics such as brake thermal efficiency, equivalence ratio, HC, CO, CO₂, NO_x and smoke emissions, start and duration of combustion, in-cylinder pressure and maximum heat release rate are compared for operation with raw biogas (50% methane) and methane enriched biogas (100% methane) for various biogas flow rates and engine torques. Results show that methane enrichment enhances brake thermal efficiency by up to 2% compared to raw biogas. Methane enrichment advances and speeds up combustion. HC, CO and CO₂ emissions, maximum cylinder pressure and maximum heat release rate are also improved with methane enrichment. Ultra-low NO_x and smoke emissions can be obtained using raw biogas as well as methane enriched biogas. Low biogas flow rates provide better brake thermal efficiency and HC emissions. Manifold injection of DEE enhances brake thermal efficiency by up to 2% compared to port injection by virtue of greater mixture homogeneity.     

Study on emissions reduction of DMCC engine with oxidation catalyst

A new combustion model diesel/methanol compound combustion (DMCC) is presented, in which methanol is injected into manifold and ignited by certain amount of diesel fuel. The results showed that DMCC remarkably decreased the emission of NO_x and the smoke, but increased the emission of HC, CO and PM. However, HC, CO and NO_x were dramatically decreased with a catalytic converter, and PM was also decreased compared with that of diesel engine. The testing results illustrated that, combined with oxidation catalyst converter, DMCC could improve engine emissions. __________ Translated from Transactions of CSICE, 2006, 24(5): 402–407 [译自: 内燃机学报]