Tribological properties of SiO2 nanoparticle filled–phthalazine ether sulfone/phthalazine ether ketone (50/50 mol %) copolymer composites

SiO₂ nanoparticle filled–poly(phthalazine ether sulfone ketone) (PPESK) composites with various filler volume fractions were made by heating compression molding. The tribological behavior of the PPESK composites was investigated using a block‐on‐ring test rig by sliding PPESK‐based composite blocks against a mild carbon steel ring. The morphologies of the worn composite surfaces, wear debris, and the transferred films formed on the counterpart steel surface were examined with a scanning electron microscope, whereas the chemical state of the Fe element in the transfer film was analyzed with X‐ray photoelectron spectroscopy. In addition, IR spectra were taken to characterize the structure of wear debris and PPESK composites. It was found that SiO₂ nanoparticle filled–PPESK composites exhibit good wear resistance and friction‐reduction behavior. The friction and wear behavior of the composites was improved at a volume fraction between 4.2 and 14.5 vol % of the filler SiO₂. The results based on combined SEM, XPS, and IR techniques indicate that SiO₂ nanoparticle filled–PPESK composite is characterized by slight scuffing in dry sliding against steel and polishing action between composite surface and that of the countpart ring, whereas unfilled PPESK is characterized by severe plastic deformation and adhesion wear. In the former case a thin, but not complete, transfer film was formed on the surface of the counterpart steel, whereas in the latter case, a thick and lumpy transfer film was formed on the counterpart steel surface. This accounts for the different friction and wear behavior of unfilled PPESK and SiO₂ nanoparticle filled–PPESK composites. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 2136–2144, 2002     

Tribological properties of micron silicon carbide filled poly(ether ether ketone)

The composite of poly(ether ether ketone) (PEEK) filled with micron silicon carbide (SiC) with different filler proportions was prepared by compression molding. The friction and wear properties of the composite were investigated at ambient conditions on a block on ring machine by running a plain carbon steel (AISI 1045 steel) ring against the composite block. The morphologies of the worn composite surfaces and the transfer film on the counterpart steel ring were examined with scanning electron microscopy and electron probe microanalysis. The results showed that the friction and wear of PEEK was slightly reduced at a filler proportion of micron SiC of 2.5–5.0 wt %. Abrasive wear was dominant for the PEEK composite; this was especially so at higher filler proportion. Meanwhile, abrasion and transfer to the composite surface of the counterpart steel ring were also observed. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 74: 2611–2615, 1999     

The tribological behavior of micrometer and nanometer TiO2 particle‐filled poly(phthalazine ether sulfone ketone) composites

Micrometer and nanometer TiO₂ particle‐filled poly(phthalazine ether sulfone ketone) (PPESK) composites with various filler volume fractions from 0.5 to 7.5 vol % were prepared by heating compression molding. The friction and wear behaviors of the PPESK composites were evaluated using the block‐on‐ring test rig by sliding PPESK‐based composite blocks against a mild carbon steel ring under dry friction conditions. The wear debris and the worn surfaces of the PPESK composites filled with micrometer and nanometer TiO₂ particles were investigated by using a scanning electron microscope (SEM), while the structures of PPESK composites and wear debris were analyzed with IR spectra. Experimental results show that antiwear properties of the PPESK composites can be improved greatly by filling nanometer TiO₂ particles, and the friction coefficient decreases when the filler volume fraction is below 2.5%, but when the filler volume fraction is above 2.5% the friction coefficient increases gradually with increasing filler volume fraction. In the case of micrometer TiO₂ filler, wear rates increase with increasing filler volume fractions under identical test conditions, and the friction coefficients are less sensitive to the filler volume fraction. It was also found that the wear mechanism of micrometer TiO₂ particle‐filled PPESK is mainly severe adhesion and abrasive wear, while that of nanometer TiO₂ particle‐filled PPESK is mainly slight abrasive wear. In the former case, there are no transfer film formed on the surface of the counterpart steel, and wear debris are in the form of long and large ribbon. While in the latter case, the wear debris was granule and their size was about 10 μm. In case of 1 vol % nanometer TiO₂ particle‐filled PPESK composites, the transfer film was fairly thinner and smoother, and the transfer film provided better coverage on the surface of steel ring, while that of 7.5 vol % was thicker and discrete. These account for the different friction and wear behavior of micrometer and nanometer TiO₂ particle‐filled PPESK composite. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 906–914, 2004     

An investigation of the friction and wear behaviors of micrometer copper particle‐ and nanometer copper particle‐filled polyoxymethylene composites

Micrometer and nanometer copper particle‐filled polyoxymethylene composites (coded as POM‐micro Cu and POM‐nano Cu, respectively) were prepared by compression molding. The compression strength and tensile strength of the composites were evaluated with a DY35 universal materials tester. An RFT‐III reciprocating friction and wear tester was used to examine the tribological properties of the composites. The elemental compositions in the transfer films and the chemical states of the elements in the composite‐worn surfaces were analyzed with electron probe microanalysis and X‐ray photoelectron spectroscopy, while the surface morphologies were observed with scanning electron microscopy. It was found that Cu( CH₂ O )_n was produced in sliding of a POM‐nano Cu pin against an AISI 1045 steel block and Cu₂O was produced in sliding of a POM‐micro Cu pin against the same counterface. POM‐micro Cu exhibited higher copper concentration in the transfer film compared with POM‐nano Cu, and the transfer film of the former was thick and patchy compared with that of the latter. It was also found that micrometer and nanometer copper particles as fillers in POM exhibit a distinctive size effect in modifying the wear mechanisms of the composites. In other words, the wear mechanism of POM‐micro Cu is mainly scuffing and adhesion, while that of POM‐nano Cu is mainly plastic deformation. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 77: 2404–2410, 2000     

Study on microhardness,dynamic mechanical,and tribological properties of PEEK/Al2O3 composites

The wear and friction properties of poly (ether‐ether‐ketone) (PEEK) reinforced with 0–33 vol % (60 wt %) micron size Al₂O₃ composites were evaluated at a sliding speed of 1.0 m/s and nominal pressure from 0.5 to 1.25 MPa under dry sliding conditions using a pin‐on‐disk wear tester. The wear resistance of the pure PEEK is 10‐fold higher than that of mild steel under the similar test condition. It is improved to 18‐fold as compared with mild steel at 3.5 vol % Al₂O₃ content. The improvement in wear properties may be attributed to the thin, tenacious, and coherent transfer film formed between the steel countersurface and composite pin. However, the wear resistance of PEEK containing above 3.5 vol % Al₂O₃ was deteriorated, despite their higher hardness and stiffness as compared with that of composites containing lower Al₂O₃ content. This is attributed to the formation of thick and noncoherent transfer film, which does not prevent the wear of the composites from hard asperities of countersurface. Moreover, hard Al₂O₃ particles present in transfer film act as third body wear mechanism. The coefficient of friction of the composites is higher than that of pure PEEK. SEM and optical microscopy have shown that wear of pure PEEK occurs by the mechanism of adhesion mainly whereas of PEEK composites by microploughing and abrasion. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Effect of nanometer SiC filler on the tribological behavior of PEEK under distilled water lubrication

The composites of polyetheretherketone (PEEK) filled with nanometer SiC of different proportions were prepared by compression molding. The tribological behaviors of the composites under lubrication of distilled water were investigated and compared with that under dry sliding, on an M‐200 friction and wear test rig, by running a plain carbon steel (AISI 1045 steel) ring against the composite block. The worn surfaces of nanometer SiC filled‐PEEK and the transfer film were observed by means of scanning electron microscopy (SEM) and electron probe microanalysis (EPMA). As the results, nanometer SiC as the filler greatly improves the wear resistance of PEEK under dry sliding and distilled water lubrication, though the composites show different dependence of wear resistance on the filler content. Nanometer SiC‐filled PEEK showed signs of slight scuffing under distilled water lubrication, while a thin, uniform, and tenacious transfer film was formed on the surface of the counterpart steel ring. On the contrary, unfilled PEEK under lubrication of water showed signs of severe plowing and erosion, while the worn surface of the counterpart ring was very rough, and a discontinuous PEEK transfer film was formed. Thus, the different friction and wear behaviors of unfilled PEEK and nanometer SiC‐filled PEEK can be attributed to the different characteristics of the corresponding transfer films. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 78: 609–614, 2000     

High performance PEEK/AlN micro‐ and nanocomposites for tribological applications

The tribological properties of poly(ether–ether–ketone) (PEEK)/aluminum nitride (AlN) composites reinforced with micro‐ and nano‐AlN particles were evaluated under dry sliding conditions. The wear resistance of pure PEEK is 10‐fold higher than mild steel. It was further improved by 2‐fold at 20 wt % micro‐AlN and by more than 4‐fold at 30 wt % nano‐AlN composite compared with pure PEEK. The improvement in wear resistance was attributed to a thin and coherent transfer film. However, it was deteriorated on further increasing micro‐AlN. The coefficient of friction of the composites was increased. Scanning electron microscopy and optical microscopy of worn surfaces and transfer films have been explained in detail. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Tribological behavior of poly(ether ether ketone) composites filled with potassium titanate whiskers sliding in different media

The friction and wear properties of poly (ether ether ketone) (PEEK) composites filled with potassium titanate whiskers (PTWs) under alkali, water, and dry conditions were investigated. The wear mechanisms in different lubrication situations were studied on the basis of examinations of the worn and counterpart surfaces with scanning electron microscopy and optical microscopy. The results showed that PTWs could obviously increase the wear resistance and reduce the friction coefficient of the PEEK composites under dry sliding conditions. Only when the PTW content was greater than 35 wt % did the wear resistance and friction coefficient deteriorate. Sliding in water caused increases in the wear rate and friction coefficient of the PEEK composites, and the PTW‐filled PEEK composites showed the highest friction coefficient and wear rate under this lubrication condition. On the contrary, sliding in an alkaline solution, the PTW‐filled PEEK composites showed the lowest friction coefficient and almost the same level of wear resistance as that found under the dry condition. Furrows and abrasive wear were the main mechanisms for the PTW‐filled PEEK composites sliding in water. The transfer onto the counterpart rings was significantly hindered with sliding under water and alkali conditions. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Tribological characteristics of nanometer Si3N4 filled poly(ether ether ketone) under distilled water lubrication

Nanometer Si₃N₄ filled poly(ether ether ketone) (PEEK) composite blocks with different filler proportions were prepared by compression molding. Their friction and wear properties under distilled water lubrication, as well as under ambient dry conditions, were investigated on a block on ring machine by running a plain carbon steel (AISI 1045 steel) ring against the PEEK composite block. The worn surfaces of nanometer Si₃N₄ filled PEEK and the transfer film were observed by scanning electron microscopy (SEM) and electron probe microanalysis (EPMA). The results showed that distilled water could reduce the friction coefficient of nanometer Si₃N₄ filled PEEK but with the sacrifice of a large reduction in wear resistance. The SEM and EPMA pictures of the worn surfaces indicated that the wear mechanisms of nanometer Si₃N₄ filled PEEK under distilled water lubrication and ambient dry rubbing conditions were different. Under water lubrication, the dominant wear mechanism of the filled PEEK was severe abrasive wear with surface fracture. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 79: 1394–1400, 2001     

Tribological properties of PTFE‐filled PMIA

The polytetrafluoroethylene‐filled (PTFE) poly(m‐phenylene isophalamide) (PMIA) composite blocks are prepared by compression molding. The friction and wear of PTFE‐filled PMIA are investigated on a block‐on‐ring machine by running the PMIA composite block against plain carbon steel (AISI 1045 steel ring). The worn surface of PMIA composite and the steel counterface are examined by using electron probe microanalysis (EPMA). It is found that PTFE‐filled PMIA exhibited considerably lower friction coefficient and wear rate than pure PMIA. Furthermore, the lowest wear rate is obtained when the composite contains 20 vol % PTFE. EPMA investigations show that there are some debris that could restrain the wear of the PMIA composites oriented along the sliding track and embedded in the surface of PMIA composite. A kind of stripe transfer film that contains abundant F element should be the main reason for the improvement of the tribological properties of PTFE‐filled PMIA composites. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 74: 747–751, 1999     

The tribological properties of SiC whisker-reinforced polyetheretherketone

SiC whisker-reinforced polyetheretherketone (PEEK) composites with different filler proportions were made into block specimens by compression molding. The friction and wear properties of the composites were investigated on a block-on-ring machine by running a plain carbon steel (AISI 1045 steel) ring against the composite block under ambient conditions. The morphologies of the wear traces and wear debris were observed by scanning electron microscopy (SEM). It was found that SiC whisker-reinforced PEEK exhibited considerably lower friction coefficient compared with pure PEEK, while SiC whisker as a filler at a content of 1.25 to 2.5 wt % was very effective in reducing the wear rate of PEEK. Especially, the lowest wear rate was obtained with the composite containing 1.25 wt % SiC whisker. The SEM pictures of the wear traces indicated that PEEK composites undertook abrasive wear that was enhanced with increasing SiC whisker content, while for the frictional couple of carbon steel ring/composite block (reinforced with 1.25 wt % filler), a thin, uniform, and tenacious transfer film was formed on the ring surface. It was also supposed that the differences in the content of SiC whisker as filler could cause the differences in the wear mechanisms of SiC whisker-reinforced PEEK composites. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 69: 2341–2347, 1998     

Tribological behaviors of polytetrafluoroethylene composites under dry sliding and seawater lubrication

The composites of polytetrafluoroethylene (PTFE) filled with expanded graphite (EG), poly(p‐oxybenzoyl) (POB), and basalt fiber (BF) were prepared by heating compression and sintering molding. The tribological behavior of PTFE composites was investigated with a pin‐on‐disk tester under dry conditions and seawater lubrication. The worn surface of PTFE composites and the transfer film on the counterface were observed with a scanning electron microscope. The results indicated that the incorporation of EG and POB improved the hardness of PTFE composites, and addition of BF led to greater load‐carrying capacity. Compared to pure PTFE, the coefficients of friction of PTFE composites slightly increased, but the wear rates were significantly reduced (the wear rate of composite with 3% EG being only 10.38% of pure PTFE). In addition, all the composites exhibited a lower coefficient of friction (decreases of about 0.03–0.07) but more serious wear under seawater lubrication than under dry sliding. The wear mechanism changed from serious abrasive wear of pure PTFE to slight adhesion wear of PTFE composites under both conditions. A transfer film was obviously found on the counterface in seawater, but it was not observed under dry conditions. Among all the materials tested, the PTFE‐based composite containing 20% POB (mass fraction), 2% EG, and 3% BF exhibited the best comprehensive performance. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 130: 2523–2531, 2013     

Functionalization of multi‐walled carbon nanotubes and their effect on the tribological properties of poly(ether ether ketone) composites

A series of copolymers containing conjugated fluorene groups as a compatibilizer to improve the dispersion of multi‐walled carbon nanotubes (MWCNTs) were prepared and used to improve the wear resistance of poly(ether ether ketone)/graphite (PEEK/GP) composites. The solubility of MWCNTs had a maximum at a concentration ratio of 2:1 polymer:MWCNTs. Transmission electron microscopy indicated that polymer ? MWCNT interactions were capable of partially debundling the nanotubes in chloroform, with individual nanotubes or small bundles clearly observed. The tribological properties of PEEK composites incorporating the modified MWCNTs were investigated using a pin‐on‐disc apparatus and a block‐on‐ring apparatus. The PEEK composites had a lower frictional coefficient under the block‐on‐ring testing condition, but a lower wear rate was achieved in the pin‐on‐disc test. © 2017 Society of Chemical Industry     

Characterization of wear surfaces in dry sliding of steel and alumina on hydrogenated and hydrogen-free carbon films

Hydrogenated amorphous carbon coatings were deposited by r.f. plasma and hydrogen-free carbon films in pulsed arc discharge on stainless steel substrates. The coatings were characterized and evaluated in tribological tests. Pin-on-disc tests were used over a wide range of test parameters: normal load, 5–40 N; sliding velocity, 0.1–3.0 m s⁻¹. The wear of both coatings was of the same order of magnitude (0.7 × 10⁻³−5.1 × 10⁻³ mm³). However, the wear of the counterface was one order of magnitude higher for the hydrogenfree carbon coatings. Increasing the normal load generally caused an increase in coating wear and in most cases also an increase in counterface wear. When the steel pin was sliding against the hydrogenated carbon coating with a high sliding velocity and load, a rather thick tribofilm was formed on the pin wear surface, lowering the coefficient of friction and reducing the pin wear. The tribofilm formed on the alumina pin sliding against the hydrogenated carbon film also seemed to reduce the friction coefficient but could not prevent the pin wear. A tribofilm was also formed on the pin wear surface when the hydrogen-free carbon coating was sliding against the steel and alumina pins, but the layer was not able to protect the pins. The tribofilm did, however, lower the coefficient of friction, which was rather insensitive to the different test parameters used. According to secondary ion mass spectroscopy analyses, material transfer of the pin was detected on the disc (coated) wear surfaces. The tribofilms formed on the pin wear surfaces consisted of pin material, hydrogen, oxygen, and carbon.     

Study on wear and friction behavior of graphite flake‐filled PTFE composites

The wear rate and coefficient of friction for graphite flake (GF)‐filled polytetrafluoroethylene (PTFE) composites were evaluated on a pin‐on‐disk wear tester under dry conditions. Scanning electron microscopy showed significant reduction in the abrasive wear of the composites. The wear rates of 5 and 10 wt % GF composites were reduced by more than 22 and 245 times, respectively, at sliding speed of 1 m/s. With increasing sliding distance from 1 to 8 km, the wear rate of pure PTFE decreased by 1.4 times whereas that of composites, it decreased up to three times. The significant decreased in wear rate and coefficient of friction might be attributed to the formation of a thin and tenacious transfer film on the counter‐surface. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Friction and wear behavior of graphite fiber-reinforced composites

Friction and wear behavior of continuous graphite fiber composites was studied for different fiber orientations against the sliding direction. The effect of fiber orientation on friction and wear of the composite and on deformation of the counterface was investigated experimentally. A pin on disk type testing machine was built and employed to generate friction and wear data. A graphite fiber composite plate was produced by the bleeder ply molding in an autoclave and machined into rectangular pin specimens with specific fiber orientations, i.e., normal, transverse, and longitudinal directions. Three different wear conditions were employed for two different periods of time, 24 and 48 hours. The wear track of the worn specimens and the metal counterface was examined and a scanning electron microscope (SEM) to observe the damaged fibers on the sliding surface of the specimen and wear film generation on the counterface. A wear mechanism of the continuous graphite fiber composite during sliding wear is proposed based on the experimental results.     

Tribological behavior of Kevlar fabric composites filled with nanoparticles

The friction and wear characteristics of ZnO‐ or montmorillonite‐nanoparticle‐filled Kevlar fabric composites with different filler proportions when sliding against stainless steel pins under dry friction conditions were studied, with unfilled Kevlar fabric composites used as references. The worn surface and transfer film of Kevlar fabric composites were then examined with a scanning electron microscope. It was found that ZnO and montmorillonite as fillers could improve the tribological behavior of the Kevlar fabric composites with various applied loads, and the best antiwear property was obtained with the composites containing 5 wt % ZnO or montmorillonite. This indicated that these nanoparticles could prevent the destruction of Kevlar fabric composites during the friction process. The transfer film established by these nanoparticles during the sliding wear of the composites against their metallic counterpart made contributions to reducing the friction coefficient and wear rate of the Kevlar fabric composites measured in the test. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Mechanical properties and sliding wear behavior of potassium titanate whiskers‐reinforced poly(ether ether ketone) composites under water‐lubricated condition

Polyetheretherketone (PEEK) composites reinforced with potassium titanate whiskers (PTW) were compounded using a twin‐screw extruder followed by injection molding. The effects of PTW on the mechanical properties, crystallization performances and wear behaviors of PEEK under water lubrication have been investigated. It was denoted that the yield strength, Young's modulus, and microhardness of the composites increased with increasing whisker content, but the elongation at break and the impact strength showed decreasing trend. It was revealed that the inclusion of PTW could effectively reduce the friction coefficient and enhance the wear resistance of the PEEK. The DSC tests showed that the crystallinity of the composite slightly decreased with the addition of PTW, which might imply that the crystallinity of PEEK was not the dominant factor that influenced the wear properties of the composites. The enhancement on the wear resistance was attributed to the reinforced effect of PTW on PEEK. The wear mechanism changed from fatigue wear into mild abrasive wear when the PTW was added into PEEK. The lowest wear rate 9.3 × 10^?8 mm³/Nm was achieved at 10 wt % PTW content. However, excessive whiskers would cause severe abrasive wear to the composite. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Improvement of the tribological behavior of ultra‐high‐molecular‐weight polyethylene by incorporation of poly (phenyl p‐hydroxyzoate)

Ultra‐high‐molecular‐weight polyethylene/poly (phenyl p‐hydroxyzoate) composites (coded as UHMWPE/PPHZ) were prepared by compression molding. The effects of the poly (phenyl p‐hydroxyzoate) on the tribological properties of the UHMWPE/PPHZ composites were investigated, based on the evaluations of the tribological properties of the composites with various compositions and the examinations of the worn steel surfaces and composites structures by means of scanning electron microscopy and transmission electron microscopy. It was found that the incorporation of the PPHZ led to a significant decrease in the wear rate of the composites. The composites with the volume fraction of the PPHZ particulates within 45% ～ 75% showed the best wear resistance. The friction coefficient of the UHMWPE/PPHZ composites decreased with increasing load and sliding velocity, while the wear rates increased with increasing load. This was attributed to the enhanced softening and plastic deformation of the composites at elevated load or sliding velocity. The UHMWPE/PPHZ composites of different compositions had differences in the microstructures and the transfer film characteristics on the counterpart steel surface as well. This accounted for their different friction and wear behaviors. The transfer film of the UHMWPE/PPHZ composites appeared to be thinner and more coherent, which was largely responsible for their better wear resistance of t composite than the UHMWPE matrix. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 96: 2336–2343, 2005     

Friction and wear behavior of basalt‐fabric‐reinforced/solid‐lubricant‐filled phenolic composites

To improve the tribological properties of basalt‐fabric‐reinforced phenolic composites, solid lubricants of MoS₂ and graphite were incorporated, and the tribological properties of the resulting basalt‐fabric composites were investigated on a model ring‐on‐block test rig under dry sliding conditions. The effects of the filler content, load, and sliding time on the tribological behavior of the basalt‐fabric composites were systematically examined. The morphologies of the worn surfaces and transfer films formed on the counterpart steel rings were analyzed by means of scanning electron microscopy. The experimental results reveal that the incorporation of MoS₂ significantly decreased the friction coefficient, whereas the inclusion of graphite improved the wear resistance remarkably. The results also indicate that the filled basalt‐fabric composites seemed to be more suitable for friction materials serving under higher loads. The transfer films formed on the counterpart surfaces during the friction process made contributions to the reduction of the friction coefficient and wear rate of the basalt‐fabric composites. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010