Carbon fiber‐reinforced gelatin composites. II. Swelling behavior

Carbon fiber‐reinforced gelatin composites have been prepared in our laboratory to obtain a novel biomaterial of improved mechanical properties. The swelling behavior (swelling rate, swelling kinetics, maximum solvent uptake, etc.) for both continuous carbon fiber‐reinforced gelatin composite (C_L/Gel) and short carbon fiber‐reinforced gelatin composite (C_S/Gel) are investigated. Experimental data show that the swelling process of the original gelatin and gelatin matrixes in both composites follows a second‐order kinetics. The swelling of the gelatin matrixes in both composites proceeds slower than that of the pristine gelatin, and depends on fiber form and fiber volume fraction (Vf). Results indicate that the presence of carbon fibers suppresses the swelling of the gelatin matrixes in both composites. It is found that the gelatin matrix in C_S/Gel possesses a smaller swelling rate and maximum solvent uptake than that in C_L/Gel. A mechanism governing these phenomena is discussed in this article. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 75: 994–998, 2000     

Hybrid effect on mechanical properties of M40‐T300 carbon fiber reinforced Bisphenol A Dicyanate ester composites

Interply and intraply hybrid composites based on Bisphenol A Dicyanate ester (BADCy), high strength carbon fibers T300, and high modulus carbon fibers M40 were prepared by monofilament dip‐winding and press molding technique. The tensile, flexural, interlaminar shear properties and SEM analysis of the hybrid composites with different fiber content and fiber arrangement were investigated. The results indicated that the mechanical properties of intraply hybrid composites were mainly determined by fiber volume contents. When the ratio of fiber volume content was close to 1:1, the intraply hybrid composites possessed lowest tensile and flexural strength. The mechanical properties of interply hybrid composite mainly depended on the fiber arrangement, instead of the fiber volume contents. The hybrid composites using T300 fiber layout as outside layer possessed high flexural strength and low flexural modulus, which was close to that of T300/BADCy composites. The hybrid composites ([(M40)_x/(T300)_y]_S) using M40 fiber layout as outside layer and T300 fibers in the mid‐plane had high flexural modulus and interlaminar shear strength. POLYM. COMPOS., 2010. © 2010 Society of Plastics Engineers     

Comparison of mechanical performance and fracture behavior of gelatin composites reinforced with carbon fibers of different fiber architectures

Gelatin‐based composites reinforced, respectively, with continuous carbon fibers, short carbon fibers, plain woven carbon fibers, and carbon fiber felt were investigated. Tensile and shear strengths, and their changes with fiber volume fraction (V_f) of these four composites were compared. It was demonstrated that at all fiber levels, the composite containing continuous carbon fibers showed the largest strength, while the composite reinforced with carbon fiber felt exhibited the lowest strength of the four composites. The above results were analyzed by comparing the fracture surfaces of the four composites. SEM confirmed the great differences in fracture surfaces for composites of different fiber architectures. The presence of a large number of pores in the C_F/Gel composite was responsible for its lowest strength, and cracks within fiber tows caused the lower strength of the C_W/Gel composite when compared to its C_L/Gel counterpart. It was suggested that fiber architecture exerted a great effect on composite performance and the effect was dependent on the nature of the matrix material.     

Pultruded fiber-reinforced poly(methyl methacrylate) composites. II. Static and dynamic mechanical properties,environmental effect,and postformability

This paper presents a novel process developed to manufacture poly(methyl methacrylate) (PMMA) pultruded composite. The mechanical, thermal, and dynamic mechanical properties, environmental effect, postformability of various fiber (glass, carbon, and Kevlar 49 aramid fiber) reinforced pultruded PMMA composites have been studied. Results show mechanical properties (i.e., tensile strength, specific tensile strength, tensile modulus, and specific flexural strength) and thermal properties (HDT) increase with fiber content. Kevlar fiber/PMMA composites possess the highest specific tensile strength and HDT, carbon fiber/PMMA composites show the highest tensile strength and tensile modulus, and glass fiber/PMMA composites show the highest specific flexural strength. Pultruded glass-fiber-reinforced PMMA composites exhibit good weather resistance. These composite materials can be postformed by thermoforming under pressure, and mechanical properties of postformed products can be improved. The dynamic shear storage and loss modulus (G′, G″) of pultruded glass-fiber-reinforced PMMA composites increased with decreasing pulling rate, and their shear storage moduli are higher than those of pultruded Nylon 6 and polyester composites.     

Pultruded fiber reinforced thermoplastic poly(methyl methacrylate) composites. Part II: Mechanical and thermal properties

A novel process has been developed to manufacture poly(methyl methacrylate) (PMMA) pultruded parts. The mechanical and dynamic mechanical properties, environmental effects, postformability of pultruded composites and properties of various fiber (glass, carbon and Kevlar 49 aramid fiber) reinforced PMMA composites have been studied. Results show that the mechanical and thermal properties (i.e. tensile strength, flexural strength and modulus, impact strength and HDT) increase with fiber content. Kevlar fiber/PMMA composites possess the highest impact strength and HDT, while carbon fiber/PMMA composites show the highest tensile strength, tensile and flexural modulus, and glass fiber/PMMA composites show the highest flexural strength. Experimental tensile strengths of all composites except carbon fiber/PMMA composites follow the rule of mixtures. The deviation of carbon fiber/PMMA composite is due to the fiber breakage during processing. Pultruded glass fiber reinforced PMMA composites exhibit good weather resistance. They can be postformed by thermoforming, and mechanical properties can be improved by postforming. The dynamic shear storage modulus (G′) of pultruded glass fiber reinforced PMMA composites increased with decreasing pulling rate, and G′ was higher than that of pultruded Nylon 6 and polyester composites.     

Three‐dimensionally braided carbon fiber–epoxy composites,a new type of materials for osteosynthesis devices. II. Influence of fiber surface treatment

Interfacial adhesion between carbon fiber and epoxy resin plays an important role in determining performance of carbon–epoxy composites. The objective of this research is to determine the effect of fiber surface treatment (oxidization in air) on the mechanical properties (flexural strength and modulus, shear and impact strengths) of three‐dimensionally (3D) braided carbon‐fiber‐reinforced epoxy (C_3D/EP) composites. Carbon fibers were air‐treated under various conditions to improve fiber–matrix adhesion. It is found that excessive oxidation will cause formation of micropits. These micropits are preferably formed in crevices of fiber surfaces. The micropits formed on fiber surfaces produce strengthened fiber–matrix bond, but cause great loss of fiber strength and is probably harmful to the overall performance of the corresponding composites. A trade‐off between the fiber–matrix bond and fiber strength loss should be considered. The effectiveness of fiber surface treatment on performance improvement of the C_3D/EP composites was compared with that of the unidirectional carbon fiber–epoxy composites. In addition, the effects of fiber volume fraction (V_f) and braiding angle on relative performance improvements were determined. Results reveal obvious effects of V_f and braiding angle. A mechanism was proposed to explain the experimental phenomena. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 1040–1046, 2002     

Influence of interfacial interactions on the properties of PVC/cellulosic fiber composites

The surface properties at the interface between thermoplastic and cellulosic fibers strongly influence the mechanical properties of plastic/cellulosic fiber composites. This paper examines the role of surface acid-base properties of plasticized PVC and cellulosic fibers on the mechanical properties of the composites. The acid-base surface characteristics of cellulosic fibers were modified by treating the fibers with γ-aminopropyltriethoxysilane (A-1100), dichlorodiethylsilane, phthalic anhydride, and maleated polypropylene. The empirical acid (K_A) and base (K_D) characteristics (i.e., electron donor/acceptor abilities) of untreated and treated fibers, as well as plasticized PVC, were determined using inverse gas chromatography (IGC) technique. These parameters were used to yield information on the acid-base pair interactions that were correlated with the tensile and notched Izod impact properties of the composites. Acid-base pair interactions have been found to be a valuable parameter in the design of surface modification strategies intended to optimize the tensile strength of the composites. By tailoring the acid-base characteristics of cellulosic fibers and plasticized PVC, a composite with equal tensile strength and greater modulus than unfilled PVC was developed. However, the acid-base factors did not correlate with tensile modulus, the elongation at break, and the notched Izod impact property of PVC/newsprint fiber composites. Aminosilane has been observed to be a suitable adhesion promoter for PVC/wood composites improving significantly the tensile strength of the composites. Other treatments (dichlorodiethylsilane, phtalic anhydride, and maleated polypropylene) were found to be ineffective, giving similar strength compared to the composites with untreated cellulosic fibers. FTIR spectroscopy results suggested that aminosilane was effective because treated cellulosic fibers can react with PVC to form chemical bonds. The resulting bond between PVC and cellulosic fibers accounts for the effectiveness of aminosilane, when compared with other coupling agents.     

Experimental investigation of the influence of the compounding process and the composite composition on the mechanical properties of a short flax fiber–reinforced polypropylene composite

Polypropylene (PP) composites containing 20 wt% short flax fibers are prepared, and the process parameters such as throughput, rotational speed, and screw configuration are varied during melt compounding with a corotating intermeshing twin‐screw extruder. The investigations reveal that low rotational speeds, high throughputs, and moderate shear energy inputs by the screw configuration led to an optimum set of mechanical properties. To investigate the influence of different composite compositions on the mechanical properties, composites with fiber contents between 0 and 40 wt% and maleic anhydride‐grafted PP (PP‐g‐MA) contents between 0 and 7 wt% are prepared. Increasing fiber contents enhance the Young's modulus and decrease the elongation at break and the notched impact strength. The tensile strength is barely affected. The addition of PP‐g‐MA increases the tensile strength as well as the elongation at break, whereas the Young's modulus is not influenced. Thus, PP‐g‐MA enhances the adhesion between PP and flax fibers significantly. POLYM. COMPOS., 36:2282–2290, 2015. © 2014 Society of Plastics Engineers     

Study on effects of short glass fiber reinforcement on the mechanical and thermal properties of PC/ABS composites

This article mainly investigated the length distributions of the alkali‐free short glass fibers in specimens and their effect on the mechanical and thermal properties of the composites. The results show that the initial length, addition level and feed way of the fibers have obvious effects on the length distributions of fibers in specimens, and thereby the mechanical and thermal properties of the composites. The main‐direction feed way has an intense shear action on the fibers in specimens. With the increase of the fiber content, the reinforcing effect of fibers on the tensile strength, flexural strength and flexural modulus of the composites is increased, while the impact strength is decreased first and then tends to be stable, and the strength factor (F) of the tensile strength to weld line is significantly reduced. The longer the fiber lengths in specimens are, the more obvious the reinforcing and toughening effects are. To some extent, with the increase of the fiber content, the storage modulus (E′) and loss modulus (E′′) of the specimens are increased, but the loss factor (Tan δ) is reduced. The effect of the fiber initial lengths on the heat‐degradation of composites is smaller than that of the fiber content. Meanwhile, adding fibers can improve the thermal stability of the composites, and this law is also confirmed by the heat deflection temperature (HDT) test. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40697.     

Preparation and properties of carbon fiber/ hydroxyapatite‐poly(methyl methacrylate) biocomposites

An in situ polymerization with a later solution co‐mixing approach was used in the preparation of polymethyl methacrylate (PMMA) matrix composites using hydroxyapatite (HA) nanoparticles and short carbon fibers(C_(f)) as reinforcing materials. The microstructures and fracture surface morphologies of the prepared C_(f)/HA‐PMMA composite were characterized using XRD, FTIR, SEM, EDS, and FESEM analyses. The mechanical properties of the composites were tested by a universal testing machine. Results show that the surface of nitric acid‐oxidized carbon fibers and lecithin‐treated HA contain new functional groups. Uniform dispersion of short fibers and HA nanoparticles in PMMA matrix is successfully achieved and the mechanical properties of the composites are obviously improved. The flexural strength, flexural modulus, and Young's modulus of the composites reach the maximum value 128.12 MPa, 1.150 GPa, and 4.572 GPa when carbon fiber and HA mass fraction arrive to 4% and 8%, respectively. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

A study of the mechanical properties of randomly oriented short banana and sisal hybrid fiber reinforced polyester composites

The mechanical performance of short randomly oriented banana and sisal hybrid fiber reinforced polyester composites was investigated with reference to the relative volume fraction of the two fibers at a constant total fiber loading of 0.40 volume fraction (V_f), keeping banana as the skin material and sisal as the core material. A positive hybrid effect is observed in the flexural strength and flexural modulus of the hybrid composites. The tensile strength of the composites showed a positive hybrid effect when the relative volume fraction of the two fibers was varied, and maximum tensile strength was found to be in the hybrid composite having a ratio of banana and sisal 4 : 1. The impact strength of the composites was increased with increasing volume fraction of sisal. However, a negative hybrid effect is observed when the impact strength of the composites is considered. Keeping the relative volume fraction of the two fibers constant, that is, banana : sisal = 0.32 : 0.08 (i.e., 4 : 1), the fiber loading was optimized and different layering patterns were investigated. The impact strength of the composites was increased with fiber loading. Tensile and flexural properties were found to be better at 0.40 V_f. In the case of different layering patterns, the highest flexural strength was observed for the bilayer composites. Compared to other composites, the tensile properties were slightly higher for the composite having banana as the skin material and sisal as the core material. Scanning electron micrographs of the tensile and impact fracture surfaces of the hybrid composites having volume fraction 0.20 and 0.40 V_f were studied. The experimental tensile strength and tensile modulus of hybrid composites were compared with those of theoretical predictions. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 96: 1699–1709, 2005     

Effect of fiber type on mechanical properties of short carbon fiber reinforced B4C composites

In order to enhance the mechanical properties of B₄C without density increase, the short carbon fibers M40, M55J and T700 reinforced B₄C ceramic composites were fabricated by hot-pressing process. The addition of the carbon fibers accelerates the densification of the B₄C, decreases their densities, and improves their strength and toughness. The enhancement effects of the three kinds of carbon fibers were studied by investigating the density, Vickers hardness and the mechanical properties such as flexural strength, flexural modulus and fracture toughness of the composites. The fiber type has a great influence on the mechanical properties and enhancement of the short carbon fiber reinforced B₄C composites. The flexible carbon fiber with high strength and low modulus such as T700 is appropriate to reinforce the B₄C matrix ceramic composites.     

Hybrid carbon-glass fiber vinyl ester resin composites

Hybrid carbon-glass fiber composites of novolak epoxy-based vinyl ester resins have been investigated. The chemical resistance, the thermo-oxidative stability and the mechanical properties such as tensile strength and tensile modulus, as well as flexural strength and flexural modulus, interlaminar shear strength (ILSS) and impact strength have also been estimated. The combination of glass and carbon fibers in the hybrid turns out to be an excellent mix. These composites have good tensile and flexural properties as well as the good chemical resistance of the carbon fibers and the high impact strength of the glass fibers and also the thermo-oxidative stability of highly aromatic vinyl ester resins based on novolak epoxy.     

The properties of dry-spun carbon nanotube fibers and their interfacial shear strength in an epoxy composite

Continuous fibers composed of carbon nanotubes have been adopted as reinforcements for polymeric composites. This paper presents several fundamental studies relevant to the mechanical behavior of CNT fibers, including fiber tensile behavior; in situ SEM observation of fiber deformation mechanisms; and fiber modulus, ultimate strength and fracture strain measurements. A modified Weibull strength distribution model that takes into account the flaw density variation with fiber diameter has been adopted for the statistical strength analysis. The interfacial shear strength between the carbon nanotube fiber and the epoxy matrix has been measured using fragmentation tests of single-fiber composites.     

Biopolyamide hybrid composites for high performance applications

This study focuses on the performance characteristics of wood/short carbon fiber hybrid biopolyamide11 (PA11) composites. The composites were produced by melt‐compounding of the fibers with the polyamide via extrusion and injection molding. The results showed that mechanical properties, such as tensile and flexural strength and modulus of the wood fiber composites were significantly higher than the PA11 and hybridization with carbon fiber further enhanced the performance properties, as well as the thermal resistance of the composites. Compared to wood fiber composites (30% wood fiber), hybridization with carbon fiber (10% wood fiber and 20% carbon fiber) increased the tensile and flexural modulus by 168% and 142%, respectively. Izod impact strength of the hybrid composites exhibited a good improvement compared to wood fiber composites. Thermal properties and resistance to water absorption of the composites were improved by hybridization with carbon fiber. In overall, the study indicated that the developed hybrid composites are promising candidates for high performance applications, where high stiffness and thermal resistance are required. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43595.     

Enhancement of the mechanical properties and interfacial interaction of a novel chitin‐fiber‐reinforced poly(ϵ‐caprolactone) composite by irradiation treatment

The effects of the fiber reinforcement of a novel bioabsorbable chitin‐fiber‐reinforced poly(?‐caprolactone) (PCL) composite were improved by irradiation treatment. The tensile strength and tensile modulus of the treated specimens were enhanced with respect to those of the untreated specimens. An increase in the fiber content (C_f) resulted in an increase in this enhancement tendency until C_f was 45%. A further increase in C_f increased the tensile modulus but decreased the strength. The flexural strength and flexural modulus were increased for the irradiation‐treated specimens in the same way as the tensile test. The microstructure of the tensile fracture showed an improvement in interfacial bonding for the irradiated specimens. The glass‐transition temperature (T_g) of the composite increased with an increase in C_f for the irradiation‐treated specimens, but there was no change in T_g for the untreated specimens with various values of C_f. This indicated that, for the composites with irradiation treatment, the fiber intensively affected the molecular segmental motion of PCL and thereby enhanced the interfacial interaction between the matrices and fibers. The same slope of the storage modulus (G′) versus the loss modulus (G″) for the irradiated specimens suggested an increase in the compatibility of the composite in comparison with the decrease in the slope with increasing C_f for the untreated specimens. All this demonstrated that there was some interfacial reaction between the fiber and matrix that resulted in the presence of an interfacial phase and improved the mechanical properties of the materials. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 84: 486–492, 2002; DOI 10.1002/app.10149     

Investigation of mechanical properties of alumina nanoparticle‐loaded hybrid glass/carbon‐fiber‐reinforced epoxy composites

This research work investigates the tensile strength and elastic modulus of the alumina nanoparticles, glass fiber, and carbon fiber reinforced epoxy composites. The first type composites were made by adding 1–5 wt % (in the interval of 1%) of alumina to the epoxy matrix, whereas the second and third categories of composites were made by adding 1–5 wt % short glass, carbon fibers to the matrix. A fourth type of composite has also been synthesized by incorporating both alumina particles (2 wt %) and fibers to the epoxy. Results showed that the longitudinal modulus has significantly improved because of the filler additions. Both tensile strength and modulus are further better for hybrid composites consisting both alumina particles and glass fibers or carbon fibers. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 39749.     

Polyethylene‐Palygorskite nanocomposite prepared via in situ coordinated polymerization

A polyethylene/palygorskite nano‐composite (IPC composite) was prepared via an in‐situ coordinated polymerization method, using TiCl₄ supported on palygorskite fibers as catalyst and alkyl aluminum as co‐catalyst. These composites were compared with those prepared by melt blending (MBC composites). It was found that in the IPC composites, nano‐size fibers of palygorskite were uniformly dispersed in the polyethylene matrix. In contrast, in the MBC composites, the palygorskite was dispersed as large clusters of fibers. Regarding the mechanical properties of the IPCs, the tensile modulus increased and the elongation at break decreased with increasing fiber content, while the tensile strength passed through a maximum. The tensile strength and elongation at break were much smaller for the MBC composites. The final degree of crystallinity of the IPC composites decreased with increasing palygorskite content. Regarding the kinetics of crystallization, the ratio between the degree of crystallinity at a given time and the final one was a universal function of time. It was found that large amouns of gel were present in the IPC composites and much smaller amountes in the MBC composites.     

Influence of complexing treatment and epoxy resin coating on the properties of aramid fiber reinforced natural rubber

In this work, natural rubber/aramid fiber (NR/AF) composites were prepared with master batch method. AF was modified by using epoxy resin (EP) and accelerator 2‐ethyl‐4‐methylimidazole (2E4MZ) through surface coating on the basis of the complexing treatment with CaCl₂ solution. Hydroxyl‐terminated liquid isoprene rubber (LIR) was regarded as a compatibilizer between EP and NR. It is found that the crystallinity on AF surface is decreased by complexing reaction with CaCl₂ solution. Swelling and mechanical properties of the vulcanized composites, such as swelling degree, tensile and tear strength, tensile modulus at 300% elongation, are measured, and the tensile fracture morphology and dynamic mechanical analysis of the composites are investigated. The results show that the mechanical properties of composites with modified fibers are improved obviously and interfacial adhesion between matrix and the fiber is enhanced, especially for the AF coated with EP and imidazole. The best comprehensive mechanical properties of the composites are obtained with using CaCl₂‐EP/2E4MZ system when the ratio of m(EP)/m(AF) is 3%. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42122.     

Mechanical and thermal characterization of native brazilian coir fiber

Coir fiber native to the Brazilian northeast coast has been characterized by mechanical, thermal, and microscopy techniques. The tensile strength, initial modulus, and elongation at break were evaluated for untreated and alkaline‐treated fibers. The results showed an enhancement of mechanical properties after 48‐h soaking in 5 wt % NaOH. The thermal stability slightly decreased after this alkaline treatment. A thermal event was observed between 28 and 38°C. The heat capacity, C_p, as a function of temperature curves between −70 and 150°C, were obtained for the untreated and alkaline‐treated coir fibers. The morphologies of the coir‐fiber surfaces and cross sections were observed by scanning electron microscopy. The properties and the morphologies were discussed, comparing the native Brazilian coir fiber with the more extensively studied native Indian coir fiber. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 76: 1197–1206, 2000