13C‐NMR study on cure‐accelerated phenol‐formaldehyde resins with carbonates

Both liquid‐ and solid‐state carbon‐13–nuclear magnetic resonance (¹³C‐NMR) spectroscopies were used to investigate the cure acceleration effects of three carbonates (propylene carbonate, sodium carbonate, and potassium carbonate) on liquid and cured phenol‐formaldehyde (PF) resins. The liquid‐phase ¹³C‐NMR spectra showed that the cure acceleration mechanism in the propylene carbonate‐added PF resin seemed to be involved in increasing reactivity of the phenol rings, whereas the addition of both sodium carbonate and potassium carbonate into PF resin apparently resulted in the presence of ortho–ortho methylene linkages. Proton spin‐lattice rotating frame relaxation time (T_1ρH) measured by solid‐state ¹³C cross polarization/magic‐angle spinning NMR spectroscopy was smaller for the cure‐accelerated PF resins than that of the control PF resin. The result indicated that the cure‐accelerated PF resins are less rigid than the control PF resin. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 77: 1284–1293, 2000     

13C‐NMR study on cure‐accelerated phenol–formaldehyde resins with carbonates

Both liquid‐ and solid‐state ¹³C‐NMR spectroscopies were employed to investigate the cure‐acceleration effects of three carbonates [propylene carbonate (PC), sodium carbonate (NC), and potassium carbonate (KC)] on liquid and cured phenol–formaldehyde (PF) resins. The liquid‐phase ¹³C‐NMR spectra showed that the cure‐acceleration mechanism in the PC‐added PF resin seemed to be involved in increasing reactivity of the phenol rings, while the addition of both NC and KC into PF resin apparently resulted in the presence of ortho–ortho methylene linkages. Proton spin‐lattice rotating frame relaxation time (T_1ρH) measured by solid‐state ¹³C‐CP/MAS‐NMR spectroscopy was smaller for the cure‐accelerated PF resins than for that of the control PF resin. The result indicated that cure‐accelerated PF resins are less rigid than the control PF resin. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 77: 841–851, 2000     

Influence of accelerated ageing on methacrylate‐based denture resins heterogeneity as viewed by ESR‐spin‐probe method

The electron‐spin‐resonance (ESR) spin‐probe method, was used to study the heterogeneity of denture resins based on poly(methyl methacrylate). Results for three resins processed by microwave energy, conventional curing and cold curing (depending on the curing procedure and exposed to ageing in various environmental conditions) were compared. All three cured resins were stored over the same time (1200 h) in distilled water at ambient temperature and in artificial saliva at 348 K. The temperature‐dependent ESR spectra of a spin probe dispersed in the denture resins are analyzed in terms of line‐shapes and line‐widths. The appearance of two spectral components was taken as an indication of resin heterogeneity. The results reveal that the cold‐cured resin has a lower local density in comparison with microwave and conventionally cured resin. The amount of residual monomer also contributes to the local motion of polymer segments. The change of denture resins exposed to ageing is influenced both by the structure of the original resin and the ageing conditions. Restricted motion of a spin probe incorporated into the acrylic resins exposed to accelerated ageing suggests additional crosslinking of polymer chains. The differences are observed for all the investigated resins, but the highest change is observed with the cold‐cured resin. The ESR results are accompanied by T_g and T_m measurements. Copyright © 2005 Society of Chemical Industry     

Reactivity,chemical structure,and molecular mobility of urea–formaldehyde adhesives synthesized under different conditions using FTIR and solid‐state 13C CP/MAS NMR spectroscopy

This study was conducted to investigate the effects of reaction pH condition and hardener type on the reactivity, chemical structure, and molecular mobility of urea–formaldehyde (UF) resins. Three different reaction pH conditions, such as alkaline (7.5), weak acid (4.5), and strong acid (1.0), were used to synthesize UF resins, which were cured by adding four different hardeners (ammonium chloride, ammonium sulfate, ammonium citrate, and zinc nitrate) to measure gel time as the reactivity. FTIR and ¹³C‐NMR spectroscopies were used to study the chemical structure of the resin prepared under three different reaction pH conditions. The gel time of UF resins decreased with an increase in the amount of ammonium chloride, ammonium sulfate, and ammonium citrate added in the resins, whereas the gel time increased when zinc nitrate was added. Both FTIR and ¹³C‐NMR spectroscopies showed that the strong reaction pH condition produced uronic structures in UF resin, whereas both alkaline and weak‐acid conditions produced quite similar chemical species in the resins. The proton rotating‐frame spin–lattice relaxation time (T_1ρH) decreased with a decrease in the reaction pH of UF resin. This result indicates that the molecular mobility of UF resin increases with a decrease in the reaction pH used during its synthesis. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 2677–2687, 2003     

Curing of low level melamine‐modified urea‐formaldehyde particleboard binder resins studied with dynamic mechanical analysis (DMA)

Effects of resin formulation, catalyst, and curing temperature were studied for particleboard binder‐type urea‐formaldehyde (UF) and 6 ～ 12% melamine‐modified urea‐melamine‐formaldehyde (UMF) resins using the dynamic mechanical analysis method at 125 ～ 160°C. In general, the UF and UMF resins gelled and, after a relatively long low modulus period, rapidly vitrified. The gel times shortened as the catalyst level and resin mix time increased. The cure slope of the vitrification stage decreased as the catalyst mix time increased, perhaps because of the deleterious effects of polymer advancements incurred before curing. For UMF resins, the higher extent of polymerization effected for UF base resin in resin synthesis increased the cure slope of vitrification. The cure times taken to reach the vitrification were longer for UMF resins than UF resins and increased with increased melamine levels. The thermal stability and rigidity of cured UMF resins were higher than those of UF resins and also higher for resins with higher melamine levels, to indicate the possibility of bonding particleboard with improved bond strength and lower formaldehyde emission. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 97: 377–389, 2005     

Time–temperature–transformation cure diagrams of phenol–formaldehyde and lignin–phenol–formaldehyde novolac resins

In this study, the time–temperature– transformation (TTT) cure diagrams of the curing processes of several novolac resins were determined. Each diagram corresponded to a mixture of commercial phenol–formaldehyde novolac, lignin–phenol–formaldehyde novolac, and methylolated lignin–phenol–formaldehyde novolac resins with hexamethylenetetramine as a curing agent. Thermomechanical analysis and differential scanning calorimetry techniques were applied to study the resin gelation and the kinetics of the curing process to obtain the isoconversional curves. The temperature at which the material gelled and vitrified [the glass‐transition temperature at the gel point (_gelT_g)], the glass‐transition temperature of the uncured material (without crosslinking; T_g0), and the glass‐transition temperature with full crosslinking were also obtained. On the basis of the measured of conversion degree at gelation, the approximate glass‐transition temperature/conversion relationship, and the thermokinetic results of the curing process of the resins, TTT cure diagrams of the novolac samples were constructed. The TTT diagrams showed that the lignin–novolac and methylolated lignin–novolac resins presented lower T_g0 and _gelT_g values than the commercial resin. The TTT diagram is a suitable tool for understanding novolac resin behavior during the isothermal curing process. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

A very simple empirical kinetic model of the acid‐catalyzed cure of urea–formaldehyde resins

The hot pressing operation is the final stage in MDF (medium density fiberboard) manufacture; the fiber mat is compressed and heated up to promote the cure of the resin. The aim of the investigations is to study the curing reactions of UF (Urea–Formaldehyde) resins as commonly used in the production of MDF, and to develop a simplified kinetic model. This investigation has combined Raman spectroscopy to study the reaction cure and ¹³C‐NMR for the quantitative and qualitative characterization of the liquid and still uncured resin. Raman spectroscopy was found very interesting for the study of the resin cure and permitted to obtain kinetic data as the basis for a simple empirical model, considering a homogeneous irreversible reaction of a single kind of methylol group and ureas with rate constants depending on their degree of substitution. Although these results can provide a better understanding of the composition and the cure of an UF resin, several issues remain open, such as the influence of the reversibility of the reactions taking place during the curing process as well as the possible formation of cyclic groups in the resin. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 5977–5987, 2006     

Curing behavior and thermal property of epoxy resin with boron‐containing phenol‐formaldehyde resin

The curing reaction of bisphenol‐A epoxy resin (BPAER) with boron‐containing phenol–formaldehyde resin (BPFR) was studied by isothermal and dynamic differential scanning calorimetry (DSC). The kinetic reaction mechanism in the isothermal reaction of BPAER‐BPFR was shown to follow autocatalytic kinetics. The activation energy in the dynamic cure reaction was derived. The influence of the composition of BPAER and BPFR on the reaction was evaluated. In addition, the glass transition temperatures (T_gs) were measured for the BPAER‐BPFR samples cured partially at isothermal temperatures. With the curing conditions varying, different glass transition behaviors were observed. By monitoring the variation in these T_gs, the curing process and the thermal property of BPAER–BPFR are clearly illustrated. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 76: 1054–1061, 2000     

Decreasing the formaldehyde emission in urea‐formaldehyde using modified starch by strongly acid process

The incorporation of the modified starch (MS) in urea‐formaldehyde resins at different stage of the synthesis was studied in this article. The synthesized resins were characterized by Fourier transform infrared spectroscopy, indicating that the ester bond can be introduced into the UF structure after the addition of MS. The curing reactions were examined with differential scanning calorimetry and it reveals that curing temperature of UF resin are slightly shifted to higher temperatures. To study the bonding strength and formaldehyde emission of the bonded plywood, the addition method and amount of MS are systematically investigated. The performance of the UF resins is remarkably improved by the addition of MS around 15% (weight percentage of the total resin) in the second stage. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40202.     

Syntheses and properties of low‐level melamine‐modified urea–melamine–formaldehyde resins

Syntheses of urea–melamine–formaldehyde (UMF) resins were studied using 2–12% melamine levels and UF base resins that were preadvanced to various different extents. The melamine reaction was carried out at pH 6.3 with F/(U + M) mole ratio of 2.1 until a target viscosity of V was reached (Gardener–Holdt) and then the second urea added at pH 8.0 to give a final F/(U + M) mole ratio of 1.15. Analyses with ¹³C‐NMR and viscosity measurements showed that MF components react fast and the UF components very slowly in the melamine reaction. Therefore, as the extent of preadvancement of UF base resin was decreased, the reaction time to reach the target viscosity became longer and the MF resin components showed high degrees of polymerization. The overpolymerization of MF components resulted in increasingly more opaque resins, with viscosity remaining stable for more than a month. As the preadvancement of UF base resin was increased, the extent of advancement of MF components decreased, to give clearer resins, with viscosity slowly increasing at room temperature. Overall, preadvancing the UF base resin components to an appropriate extent was found to be a key to synthesizing various low‐level melamine‐modified UMF resins. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 2559–2569, 2004     

Modification of a two‐component system by introducing an epoxy‐reactive diluent: Construction of a time–temperature–transformation (TTT) diagram

Curing reactions of a three‐component system consisting of an epoxy resin diglycidyl ether of bisphenol A (DGEBA n = 0), 1,2‐diaminecyclohexane as curing agent, and vinylcyclohexene dioxide as a reactive diluent were studied to calculate a time–temperature–transformation isothermal cure diagram for this system. Differential scanning calorimetry (DSC) was used to calculate the vitrification times. DSC data show a one‐to‐one relationship between T_g and fractional conversion α, independent of cure temperature. As a consequence, T_g can be used as a measure of conversion. The activation energy for the polymerization overall reaction was calculated from the gel times obtained using the solubility test (58.5 ± 1.3 kJ/mol). This value was similar to the results obtained for other similar epoxy systems. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 1190–1198, 2004     

Addition‐cure‐type phenolic resin based on alder‐ene reaction: Synthesis and laminate composite properties

A maleimide‐functional phenolic resin was reactively blended with an allyl‐functional novolac in varying proportions. The two polymers were coreacted by an addition mechanism through Alder‐ene and Wagner–Jauregg reactions to form a crosslinked network system. The cure characterization was done by differential scanning calorimetry and dynamic mechanical analysis. The system underwent a multistep curing process over a temperature range of 110–270°C. Although the cure profiles were independent of the composition, the presence of maleimide led to a reduced isothermal gel time of the blend. Increasing the allylphenol content decreased the crosslinking in the cured matrix, leading to enhanced toughness and improved resin‐dominant mechanical properties of the resultant silica laminate composites. Changing the reinforcement from silica to glass resulted in further amelioration of the resin‐reinforcement interaction, but the resin‐dominant properties of the composite remained unaltered. Increasing the maleimide content resulted in enhanced thermal stability. Integrating both the reactive groups in a single polymer and its curing led to enhanced thermal stability and T_g, but to decreased mechanical properties of the laminate composites. This can be attributed to a brittle matrix resulting from enhanced crosslinking facilitated by interaction of the reactive groups located on the polymer of an identical backbone structure. The cured polymers showed a T_g in the range of 170–190°C. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 80: 737–749, 2001     

Relationship between curing activation energy and free formaldehyde content in urea-formaldehyde resins

This study investigated the effect on the curing behavior, activation energy (E _a) of the curing reaction, crystalline structure, crosslinking, and free formaldehyde content of the addition of the following scavengers in urea-formaldehyde (UF) resins: medium density fiber board flour, rice husk flour, silica powder, and tannin powder. The scavenger content was 3 and 7?wt% of the UF resin solid content. The curing behavior of UF resins was monitored by differential scanning calorimetry, thermogravimetric analysis, and X-ray crystallography. The curing E _a was correlated to the free formaldehyde content of the scavenger containing UF resins. The thermal stability of the UF resins increased but the curing E _a decreased with increasing scavenger content. After curing, the crystallinity of the UF resins decreased in the presence of scavengers. The unreacted free formaldehyde content was reduced in the tannin powder containing UF resins. The degree of crosslinking affects the formaldehyde emission from wood panels bonded with UF resin. This is especially true for wood panels in service for long periods of time and exposed to high humidity conditions. Once the free formaldehyde which influences considerably the emission has disappeared, the presence of the –CH₂– groups then becomes important. Hence, an increased resin crosslinking indicates a higher concentration of –CH₂– groups present, which may hydrolyze and emit formaldehyde slowly over time.     

New thermosetting resin from poly(p‐vinylphenol) based benzoxazine and epoxy resin

Poly(p‐vinylphenol) (VP) based benzoxazine was prepared from VP, formaline, and aniline. The curing behavior of the benzoxazine with the epoxy resin and the properties of the cured resin were investigated. Consequently, the curing reaction did not proceed at low temperatures, but it proceeded rapidly at higher temperatures without a curing accelerator. The reaction induction time or cure time of the molten mixture from VP based benzoxazine and epoxy resin was found to decrease, compared with those from conventional bisphenol A based benzoxazine and epoxy resin. The curing reaction rate of VP based benzoxazine and epoxy resin increased more than that of conventional bisphenol A based benzoxazine and epoxy resin. The properties of the cured resin from neat resins and from reinforced resins with fused silica were evaluated. The cured resins from VP based benzoxazine and epoxy resin showed good heat resistance, mechanical properties, electrical insulation, and water resistance compared to the cured resin from VP and epoxy resin using imidazole as the catalyst. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 79: 555–565, 2001     

Kinetics and thermal characterization of epoxy‐amine systems

The curing behavior of epoxy resins was analyzed based on a simple kinetic model. We simulated the curing kinetics and found that it fits the experimental data well for both diglycidylether of bisphenol A–4,4′‐methylene dianiline and diglycidylether of bisphenol A–carboxyl‐terminated butadiene acrylonitrile–4,4′‐methylene dianiline systems. The kinetic results showed the curing of epoxy resins involves different reactive process and reaction stages, and the value of activation energy is dependent on the degree of conversion. By analyzing the effect of vitrification, at low curing temperature, we found the curing reaction at the later stage was practically diffusion‐controlled for unmodified resin, and the rubber component did not markedly decrease T_g at the early stage of reaction as would be expected. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 71: 2401–2408, 1999     

Curing kinetics of a “green” thiol‐containing resin: Oligo(ethylene‐2‐mercaptosuccinate)

This work focuses on examining the curing process of neat oligo(ethylene‐2‐mercaptosuccinate) using differential scanning calorimetry (DSC), rheology, and Fourier transform infrared (FTIR) spectroscopy. The thiol‐containing resin offers much promise as a bioabsorbable polymer in medical field and as a reusable thermoset in sustainable applications. Although curing between thiol groups has been investigated in solutions, studies of neat materials without solvent are rare. Here, the evolution of glass transition temperature (T_g), complex shear modulus (G*), gelation, and chemical structure are monitored as a function of isothermal curing time and temperature. Both T_g and G* increase with curing, indicating the formation of polymer networks. The conversion of the cure is determined from the DiBenedetto equation and is found to follow a second‐order plus second‐order autocatalytic reaction model. Importantly, the intensity of the S–H bond absorption decreases with the extent of curing, which confirms the curing mechanism, i.e., disulfide formation between the thiol groups. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43205.     

Cure kinetics of aqueous phenol–formaldehyde resins used for oriented strandboard manufacturing: Analytical technique

The cure kinetics of commercial phenol–formaldehyde (PF), used as oriented strandboard face and core resins, were studied using isothermal and dynamic differential scanning calorimetry (DSC). The cure of the face resin completely followed an nth‐order reaction mechanism. The reaction order was nearly 1 with activation energy of 79.29 kJ mol^?1. The core resin showed a more complicated cure mechanism, including both nth‐order and autocatalytic reactions. The nth‐order part, with reaction order of 2.38, began at lower temperatures, but the reaction rate of the autocatalytic part increased much faster with increase in curing temperature. The total reaction order for the autocatalytic part was about 5. Cure kinetic models, for both face and core resins, were developed. It is shown that the models fitted experimental data well, and that the isothermal DSC was much more reliable than the dynamic DSC in studying the cure kinetics. Furthermore, the relationships among cure reaction conversion (curing degree), cure temperature, and cure time were predicted for both resin systems. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 1642–1650, 2006     

Catalytic effect of 2,2′‐diallyl bisphenol A on thermal curing of cyanate esters

Cyanate esters are a class of thermal resistant polymers widely used as thermal resistant and electrical insulating materials for electric devices and structural composite applications. In this article, the effect of 2,2′‐diallyl bisphenol A (DBA) on catalyzing the thermal curing of cyanate ester resins was studied. The curing behavior, thermal resistance, and thermal mechanical properties of these DBA catalyzed cyanate ester resins were characterized. The results show that DBA is especially suitable for catalyzing the polymerization of the novolac cyanate ester resin (HF‐5), as it acts as both the curing catalyst through depressing the exothermic peak temperature (T_exo) by nearly 100°C and the toughening agent of the novolac cyanate ester resin by slightly reducing the elastic modulus at the glassy state. The thermogravimetric analysis and dynamic mechanical thermal analysis show that the 5 wt % DBA‐catalyzed novolac cyanate ester resin exhibits good thermal resistance with T_d⁵ of 410°C and the char yield at 900°C of 58% and can retain its mechanical strength up to 250°C. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 1775–1786, 2006     

Curing characteristics of urea–formaldehyde resin in the presence of various amounts of wood extracts and catalysts

The characteristics of urea–formaldehyde (UF) resin curing in the presence of wood extracts and a catalyst [ammonium chloride (NH₄Cl)] were investigated by differential scanning calorimetry (DSC). The effects of extracts from 16 wood species on resin curing behaviors were evaluated. A model developed in this study, T_p = 53.296 exp(?9.72C) + 93.104, could be used to predict the resin curing rate in terms of the DSC peak temperature (T_p) as influenced by the NH₄Cl content (C). The results indicated that the curing rate of UF resin increased as the catalyst content increased and reached a maximum when the catalyst content ranged from 0.5 to 1.0% (solid basis over liquid UF resin weight). Further increases in the catalyst content had no effect on the resin curing rate. The curing rates of UF resin in the presence of wood extracts increased with decreased pH values or increased base buffer capacities. It was also discovered that the activation energy could not fully explain the resin curing behavior when some species of wood extracts were present, and therefore, the pre‐exponential factor had to be taken into account. The concept of the equivalent catalyst content (ECC) of wood extracts to the NH₄Cl content was introduced in this study; ECCs ranged from 0.0022 to 0.0331% among the 16 wood species. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008