Performance analysis for the dynamic virtual path bandwidth control method in ATM networks

Broadband ISDN (integrated services digital network) should provide various kinds of communication services for multimedia traffic, including voice, computer data, still picture and motion video, and an ATM (asynchronous transfer mode) technology is expected to satisfy those demands. In ATM networks, a VP (virtual path) concept is introduced for simplifying the network resource management. However, if the bandwidth of each VP is fixed, it cannot absorb traffic load fluctuation. In this case, it is likely to happen that one VP has no remaining bandwidth while other VPs on the same physical link have free capacities. Another extremity is that a VP is not introduced, and that all VCs along the same physical link share the whole bandwidth of the link. This can achieve an efficient use of the link, but it apparently requires complicated call set-up procedures. In this paper, we propose a new dynamic VP bandwidth control method, in which the bandwidth allocated to each VP is dynamically changed according to traffic fluctuation. More specifically, in the case that multiple VPs are multiplexed on the same link between two nodes, when the utilization of some VP is increased, that VP requests an additional bandwidth. When the traffic load becomes low and the utilization of a VP is decreased, a part of the assigned bandwidth is released. We consider two methods for this purpose; one is the basic method in which the bandwidth increase request is issued after the VP bandwidth is exhausted. The other is the look-ahead method where the bandwidth increase is requested in advance before the bandwidth starvation. An approximate analysis for the above methods is provided, and the validation of its accuracy is assessed by comparing with simulation results. Through numerical examples, we show that our methods can provide performance improvement in terms of call loss probabilities of each VP.     

Resource allocation for broadband networks

The major benefit of a broadband integrated ATM (asynchronous transfer mode) network is flexible and efficient allocation of communications bandwidth for communications services. However, methods are needed for evaluating congestion for integrated traffic. The author suggests evaluating congestion at different levels, namely the packet level, the burst level, and the call level. Congestion is measured by the probabilities of packet blocking, burst blocking, and call blocking. He outlines the methodologies for comparing these blocking probabilities. The author uses the congestion measures for a multilayer bandwidth-allocation algorithm, emulating some function of virtual circuit setup, fast circuit switching, and fast packet switching at these levels. The analysis also sheds insight on traffic engineering issues such as appropriate link load, traffic integration, trunk group and switch sizing, and bandwidth reservation criteria for two bursty services     

Estimation of the cell loss ratio in ATM networks with a fuzzysystem and application to measurement-based call admission control

An important parameter in asynchronous transfer model (ATM)-based network design and management is the cell loss ratio (CLR) in ATM multiplexers. It is a key parameter to many vital functions in the network such as call admission control (CAC), bandwidth allocation, etc. However, the CLR depends usually on many unknown and unpredictable traffic parameters such as input traffic correlations. In this paper, we propose a simple and robust fuzzy-based algorithm to predict the CLR in large-sized systems based on both a small amount of information from small-sized systems, and the asymptotic behavior for very large systems. Unlike the model-based approaches, our approximation avoids the problem of assuming any traffic parameters or arrival process. This algorithm is used with real-time traffic measurement to propose an effective measurement-based call admission control framework for ATM networks     

Architectural design and bandwidth demand analysis for multiparty videoconferencing on SONET/ATM rings

In this paper, we propose a scheme for implementing multiparty videoconferencing service on SONET/ATM rings. We focus on the architectural design and bandwidth demand analysis. Different multicasting methods on SONET/ATM rings are discussed and compared. A new multicast virtual path (VP) called "Multidrop VP" which is particularly suitable for SONET/ATM rings is proposed. An add-drop multiplexer (ADM) structure for rings capable of multidropping is also presented. Several VP assignment schemes are proposed and their bandwidth utilizations are compared.     

Design of ATM Networks with Multiple Traffic Classes

In this paper, we propose a new heuristic design algorithm for the virtual path (VP)-based ATM network with multiple traffic classes, in which QoS constraints associated with traffic class are taken into account. The minimum bandwidth of VP required to carry given amount of traffic is obtained by utilizing an equivalent bandwidth concept, and the route of each VP is placed so that the network cost is minimized while the QoS requirement is fulfilled. To evaluate our design algorithm, we consider two kinds of traffic: voice traffic as low speed service and still picture traffic as high speed service. Through numerical examples, we demonstrate that our design method can achieve an efficient use of network resources, which results in providing a cost-effective VP-based ATM network.     

Design and analysis of a bandwidth management framework forATM-based broadband ISDN

When designing and configuring an ATM-based B-ISDN, it remains difficult to guarantee the quality of service (QoS) for different service classes, while still allowing enough statistical sharing of bandwidth so that the network is efficiently utilized. These two goals are often conflicting. Guaranteeing QoS requires traffic isolation, as well as allocation of enough network resources (e.g., buffer space and bandwidth) to each call. However, statistical bandwidth sharing means the network resources should be occupied on demand, leading to less traffic isolation and minimal resource allocation. The authors address this problem by proposing and evaluating a network-wide bandwidth management framework in which an appropriate compromise between the two conflicting goals is achieved. Specifically, the bandwidth management framework consists of a network model and a network-wide bandwidth allocation and sharing strategy. Implementation issues related to the framework are discussed. For real-time applications the authors obtain maximum queuing delay and queue length, which are important in buffer design and VP (virtual path) routing     

企业级视频会议服务质量保证机制的研究

针对企业网络的情况,提出了一种企业级视频会议系统的服务质量保证机制。该机制根据视频会议的传输模式,将视频会议的保障转化成对一组具有时间尺度数据流的保障,通过对网络中优先级带宽的管理来为数据流提供预约带宽,在网络的边缘对每个优先级数据流进行认证、标记和整形,在网络核心使用区分服务保障视频流的优先转发,以实现预约带宽的合法使用。实验结果表明该机制能够在网络拥塞的情况下为媒体流提供所需的带宽,能有效地保证视频会议的服务质量。     

企业级视频会议动态时间槽多播带宽提前预留算法

为了保证视频会议的服务质量和提高企业网络资源利用率,研究了企业级视频会议系统带宽提前预留问题。在企业级网络中经常出现同时在线会议数量多达数百个量级的情况,而且任意两个会议成员之间都有可能视频通信。为会议提前预留带宽将导致未来可用带宽随时间而呈细粒度变化,特别是同时出现大量会议请求时,时间开销和带宽使用将大幅度增长。为解决此问题,提出了动态时间槽多播带宽提前预留算法。该算法综合考虑了IETF XCON工作小组提出的两种不同会议场景。仿真结果表明,相比其他算法,该算法能够有效地给大数据会议申请预留带宽,解决时间开销瓶颈问题。     

基于有线电视网和IP网的视频会议系统设计与实现

设计并实现了一种结合有线电视网和IP网的视频会议系统.该系统以会议服务器为中心单元,协调各会场间的数据流和控制流传递,利用双向IP网,实现会议服务器和各会场间的会议控制等交互操作,以及上传各会场的音视频至会议服务器.它基于多播协议,利用有线电视网稳定可靠的高速下行带宽,将上载的音视频高质量地传送至各会场.     

A heuristic approach of bandwidth management for video sources in ATM networks

One of the most important properties in the ATM network is that the resource of the network, including buffer and bandwidth, can be flexibly managed according to different demands of various applications. The network bandwidth can be effectively allocated and utilized if the data volume of the arrival traffic can be predicted precisely. In this paper, we study the bandwidth management schemes for variable bit rate (VBR) pre‐coded MPEG video sources. The proposed bandwidth allocation method, which predicts the bandwidth by the frame correlation, demonstrates a quite good performance when comparing with a previous scheme, especially for the video scenes with the combination of intraframes and interframes. Bandwidth allocation of a multiplexer connected to several video sources is also studied by using heuristic information. The experimental results show that the proposed method is much better than that of the fixed bandwidth allocation and is suitable for the application of MPEG video services. Copyright © 2000 John Wiley & Sons, Ltd.     

Modeling and call admission control algorithm of variable bit ratevideo in ATM networks

The authors propose a new method for the modeling and call admission control (CAC) of variable bit rate video source, which come to the front of ATM networks as hot issues nowadays. First, the modeling of video source is accomplished using the three-state Markov chains including the effects of scene change at which the bit rate of video source is abruptly increased. Also, using two AR models, they improve the defects which an AR model has in modeling a video source. In addition, they represent the analytical model of a video source so that a network manager can acquire the information which is very important in managing the entire networks. CAC is accomplished using the previously defined analytical model. A routing manager calculates the cell loss probability of a chosen VP where a new call is connected so that the routing manager decides whether this new call is accepted or not. This calculation is accomplished through the GB/D/1-S queuing system. Using BIA (bandwidth increasing algorithm), they check whether the calls rejected by the routing manager could be accepted if possible. Finally, the applicable procedures to suitable allocate bandwidth to each VP on a link are presented in detail     

Multi-hour, multi-traffic class network design for virtualpath-based dynamically reconfigurable wide-area ATM networks

The virtual path (VP) concept has been gaining attention in terms of effective deployment of asynchronous transfer mode (ATM) networks in recent years. In a recent paper, we outlined a framework and models for network design and management of dynamically reconfigurable ATM networks based on the virtual path concept from a network planning and management perspective. Our approach has been based on statistical multiplexing of traffic within a traffic class by using a virtual path for the class and deterministic multiplexing of different virtual paths, and on providing dynamic bandwidth and reconfigurability through virtual path concept depending on traffic load during the course of the day. In this paper, we discuss in detail, a multi-hour, multi-traffic class network (capacity) design model for providing specified quality-of-service in such dynamically reconfigurable networks. This is done based on the observation that statistical multiplexing of virtual circuits for a traffic class in a virtual path, and the deterministic multiplexing of different virtual paths leads to decoupling of the network dimensioning problem into the bandwidth estimation problem and the combined virtual path routing and capacity design problem. We discuss how bandwidth estimation can be done, then how the design problem can be solved by a decomposition algorithm by looking at the dual problem and using subgradient optimization. We provide computational results for realistic network traffic data to show the effectiveness of our approach. We show for the test problems considered, our approach does between 6% to 20% better than a local shortest-path heuristic. We also show that considering network dynamism through variation of traffic during the course of a day by doing dynamic bandwidth and virtual path reconfiguration can save between 10% and 14% in network design costs compared to a static network based on maximum busy hour traffic     

The extended connection‐dependent threshold model for call‐level performance analysis of multi‐rate loss systems under the bandwidth reservation policy

Firstly, we reviewed two extensions of the Erlang multi‐rate loss model, whereby we can assess the call‐level QoS of telecom networks supporting elastic traffic: (i) the extended Erlang multi‐rate loss model, where random arriving calls of certain bandwidth requirements at call setup can tolerate bandwidth compression while in service; and (ii) the connection‐dependent threshold model, where arriving calls may have several contingency bandwidth requirements, whereas in‐service calls cannot tolerate bandwidth compression. Secondly, we proposed a new model, the extended connection‐dependent threshold model. Calls may have alternative bandwidth requirements at call setup and can tolerate bandwidth compression while in service. We proposed a recurrent formula for the efficient calculation of link occupancy distribution and consequently call blocking probabilities, link utilization, and throughput per service class. Furthermore, in the proposed model, we incorporated the bandwidth reservation policy, whereby we can (i) equalize the call blocking probabilities of different service classes, (ii) guarantee specific QoS per service class, and (iii) implement different maximum bandwidth compression/expansion rate per service class so that the network supports both elastic and stream traffic. The accuracy of the new model is verified by simulation. Moreover, the proposed model performs better than the existing models. Finally, we generalize the proposed model by incorporating service classes with either random or quasi‐random arrivals. Copyright © 2011 John Wiley & Sons, Ltd.     

Dynamic bandwidth allocation and buffer dimensioning under equal segment scheme to support video‐on‐demand services

This paper focuses on the optimization of network bandwidth allocation and buffer dimensioning to transport pre‐stored MPEG video data from source to playback destination across ATM networks. This is one of the most important issues in the support of video‐on‐demand (VoD) service. This paper provides a novel scheme in the dynamic allocation of bandwidth to segments of video using ABR mode. The dynamic bandwidth allocation is based on a new concept, called playback tunnel which is obtained from the traffic characteristics of the pre‐stored MPEG video trace to determine the optimum of transmission bandwidth as well as the buffer capacity to ensure that the playback buffer neither underflows nor overflows. The proposed scheme is tested with real‐life MPEG video traces. The obtained results have shown its significant performance improvement in terms of the capacity of playback buffer, the start‐up playback delay, the size of video segment and the network multiplexing gain. Copyright © 2001 John Wiley & Sons, Ltd.     

Simulation study on ATM multiplexing of MPEG video sources

In this paper we study the performance of ATM multiplexing of homogeneous MPEG video sources. A source scheduling method is developed to improve the performance of ATM multiplexer for MPEG video sources. Simulation results show that the level of burstiness for the aggregated MPEG traffic is reduced and the network performance is enhanced. Based on the rationale of the source scheduling method, a simple but efficient bandwidth allocation algorithm is also derived for connection admission of MPEG video in an ATM multiplexer. Copyright © 2001 John Wiley & Sons, Ltd.     

Virtual path control for ATM networks with call level quality ofservice guarantees

The configuration of virtual path (VP) connection services is expected to play an important role in the operation of large-scale asynchronous transfer mode (ATM) networks. A major research challenge is to understand the fundamental tradeoff between the network call throughput and the processing load on the signaling system and to provide an algorithm for VP capacity allocation that achieves an optimal network operating point while guaranteeing quality of service (QoS) at the call level and satisfies a priori bounds on the processing load of the call processors. We present a taxonomy of previous approaches to the problem and identify their strengths and weaknesses. Based on these observations, we provide an algorithm for the VP capacity allocation problem that satisfies nodal constraints on the call processing load and blocking constraints for each source-destination (SD) pair. The algorithm maximizes the network revenue under the above set of constraints and is parameterized by the number of traffic classes in the network, the method of presentation of networking resources, the admission control policy used in every link and VP, and the network routing scheme. Finally, we apply the algorithm to three sample networks and study several of its performance characteristics. In one case, we applied the calculated VP distribution to the Xunet ATM testbed and verified experimentally the predicted performance     

Adaptive bandwidth management in ATM networks

A framework for adaptive bandwidth management in ATM based networks is proposed. It is based on a layered approach which includes bandwidth allocation to virtual networks. The central concept of this approach is adaptive estimation of the effective bandwidth required, by connections carried in the network. To achieve reliable results the estimation process takes into account both the traffic source declarations and the connection superposition process measurements on the network links. This is done in an optimization framework provided by estimation theory. A study, based on a linear two-state Kalman filter, shows that the proposed approach provides good adaptation to undeclared changes in traffic parameters and that the network performance is significantly improved when compared to the effective bandwidth allocation based solely on the source parameters declarations. These features allow more relaxed source parameter declarations and at the same time permit less stringent source policing. Thus the two bottlenecks influencing bandwidth management in ATM networks can be significantly widened.     

Medium-term centralized virtual-path bandwidth control based ontraffic measurements

The paper presents a centralized virtual path bandwidth (VPB) control scheme for ATM networks which satisfies mainly three specifications: a) optimality during a medium-term control interval, b) fast time response so as to absorb the medium-term traffic fluctuations, and c) easy implementation. The paper mainly points at the impact of direct, on-line traffic measurements on bandwidth control. The control objective is to rearrange the installed bandwidth of the virtual paths according to the offered traffic so as to minimize the maximum call blocking probability of the whole network. Network simulation shows that a sophisticated VPB controller which relies on simple measurements of the offered traffic can substantially improve the performance of an ATM network. The necessary bandwidth rearrangement time is also examined by simulation