Improvement of the homogeneity of SBR/NBR blends using polyglycidylmethacrylate‐g‐butadiene rubber

Polyglycidylmethacrylate grafted butadiene rubber (PGMA‐g‐BR) was synthesized by a graft solution copolymerization technique. The PGMA content was determined through titration against HBr. The PGMA‐g‐BR was blended with styrene butadiene rubber/butadiene acrylonitrile rubber (SBR/NBR) blends with different blend ratios. The SBR/NBR (50/50) blend was selected to examine the compatibility of such blends. Compatibility was examined using scanning electron microscopy (SEM), differential scanning calorimetry (DSC), and viscosity measurements. The scanning electron micrographs illustrate the change of morphology of the SBR/NBR rubber blend as a result of the incorporation of PGMA‐g‐BR onto that blend. The T_gs of SBR and NBR in the blend get closer upon incorporation of PGMA‐g‐BR 10 phr, which indicates improvement in blend homogeneity. The intrinsic viscosity (η) versus blend ratio graph shows a straight‐line relationship, indicating some degree of compatibility. Thermal stability of the compatibilized and uncompatibilized rubber blend vulcanizates was investigated by determination of the physicomechanical properties before and after accelerated thermal aging. Of all the vulcanizates with different blend ratios under investigation, the SBR/NBR (25/75) compatibilized blend possessed the best thermal stability. However, the SBR/NBR (75/25) compatibilized blend possessed the best swelling performance in brake fluid. The effect of various combinations of inorganic fillers on the physicomechanical properties of that blend, before and after accelerated thermal aging, was studied in the presence and absence of PGMA‐g‐BR. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 99: 1559–1567, 2006     

Influence of rubber composition on migration behaviors of antiozonants in carbon black‐filled rubber vulcanizates composed of NR,SBR, and BR

Migration behaviors of antiozonants in carbon black‐filled rubber vulcanizates with different rubber compositions of natural rubber (NR), styrene–butadiene rubber (SBR), and butadiene rubber (BR) were studied at constant temperatures of 40–100°C and outdoors. Three single rubber‐based vulcanizates, three biblends, and three triblends were used. N‐Phenyl‐N′‐isopropyl‐p‐phenylenediamine (IPPD) and N‐phenyl‐N′‐(1,3‐dimethylbutyl)‐p‐phenylenediamine (HPPD) were employed as antiozonants. Migration rates of the antiozonants became faster with increasing the temperature. The order of the migration rates in the single rubber‐based vulcanizates was BR > NR > SBR. The migration rates in the vulcanizates containing SBR, on the whole, increased with decreasing the SBR content, while those in the vulcanizates containing BR decreased with decreasing the BR content. Difference in the migration behaviors of the antiozonants depending on the rubber composition was explained both by the intermolecular interactions of the antiozonants with the matrix and by interface formed between dissimilar rubbers in the blends. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 81: 237–242, 2001     

Compatibility studies on some polymer blend systems by electrical and mechanical techniques

Systematic electrical and mechanical studies were carried out on natural rubber (NR) blended with different types of synthetic rubber such as styrene‐butadiene rubber (SBR), polybutadiene rubber (BR), and ethylene‐propylene‐diene monomer (EPDM) as nonpolar rubbers and nitrile‐butadiene rubber (NBR) and chloroprene rubber (CR) as polar rubbers. The NR/SBR, NR/BR, NR/EPDM, NR/NBR, and NR/CR blends were prepared with different ratios (100/0, 75/25, 50/50, 25/75, and 0/100). The permittivity (ε′) and dielectric loss (ε″) of these blends were measured over a wide range of frequencies (100 Hz–100 kHz) and at room temperature (∼ 27°C). The compatibility results obtained from the dielectric measurements were comparable with those obtained from the calculation of the heat of mixing. These results were confirmed by scanning electron microscopy and showed that NR/SBR and NR/BR blends were compatible while NR/EPDM, NR/NBR, and NR/CR blends were incompatible. To overcome the problem of phase separation (incompatibility) between NR and EPDM, NBR, or CR, a third component such as SBR or poly(vinyl chloride) (PVC) was added as a compatibilizing agent to these blends. The experimental data of dielectric and mechanical measurements showed that the addition of either SBR or PVC could improve the compatibility of such blends to some extent. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 79: 60–71, 2001     

Influences of trans‐polyoctylene rubber on the physical properties and phase morphology of natural rubber/acrylonitrile–butadiene rubber blends

The influence of trans‐polyoctylene rubber (TOR) on the mechanical properties, glass‐transition behavior, and phase morphology of natural rubber (NR)/acrylonitrile–butadiene rubber (NBR) blends was investigated. With an increased TOR level, hardness, tensile modulus, and resilience increased, whereas tensile strength and elongation at break tremendously decreased. According to differential scanning calorimetry and dynamic mechanical analysis, there were two distinct glass‐transition temperatures for a 50/50 NR/NBR blend, indicating the strongly incompatible nature of the blend. When the TOR level was increased, the glass transition of NBR was strongly suppressed. NBR droplets of a few micrometers were uniformly dispersed in the continuous NR phases in the NR/NBR blends. When TOR was added to a 50/50 NR/NBR blend, TOR tended to be located in the NR phase and in some cases was positioned at the interfaces between the NBR and NR phases. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 125–134, 2002     

Compatibilization of SBR/NBR blends using chemically modified styrene‐co‐butadiene rubber Part 2. Effect of compatibilizer loading

The present work focuses on the compatibization of styrene‐co‐butadiene rubber (SBR)/acrylonitrile‐co‐butadiene rubber (NBR) blends with dichlorocarbene modified styrene‐co‐butadiene rubber (DCSBR) as a function of concentration of compatibilizer and composition of the blend. FTIR studies, differential scanning calorimetry and dynamic mechanical analysis reveal molecular level miscibility in the blends in the presence of compatibilizer. The formation of interfacial bonding is assessed by analysis of swelling behaviour, cure characteristics, stress–strain data and mechanical properties. These studies show that the compatibilizing action of DCSBR becomes more prominent as the proportion of NBR in the blend increases. The resistance of the vulcanizate towards thermal and oil ageing improved with compatibilization. The change in technological properties is correlated with the crosslink density of the blends assessed from swelling and stress–strain data. © 2001 Society of Chemical Industry     

Silica‐modified SBR/BR blends

The purpose of this article is that the silica‐modified SBR/BR blend replaces natural rubber (NR) in some application fields. The styrene‐butadiene rubber (SBR) and cis‐butadiene rubber (BR) blend was modified, in which silica filler was treated with the r‐Aminopropyltriethoxysilane (KH‐550) as a coupling agent, to improve mechanical and thermal properties, and compatibilities. The optimum formula and cure condition were determined by testing the properties of SBR/BR blend. The properties of NR and the silica‐modified SBR/BR blend were compared. The results show that the optimum formulawas 80/20 SBR/BR, 2.5 phr dicumyl peroxide (DCP), 45 phr silica and 2.5 mL KH‐550. The best cure condition was at 150°C for 25 min under 10 MPa. The mechanical and thermal properties of SBR/BR blend were obviously modified, in which the silica filler treated with KH‐550. The compatibility of SBR/BR blend with DCP was better than those with benzoyl peroxide (BPO) and DCP/BPO. The crosslinking bonds between modified silica and rubbers were proved by Fourier transform infrared analysis, and the compatibility of SBR and BR was proved by polarized light microscopy (PLM) analysis. The silica‐modified SBR/BR blend can substitute for NR in the specific application fields. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011.     

Influence of rubber composition on change of crosslink density of rubber vulcanizates with EV cure system by thermal aging

Variation of the crosslink density of a rubber vulcanizate depending on the rubber composition after the thermal aging was studied with single rubber, biblend, and triblend vulcanizates of natural rubber (NR), butadiene rubber (BR), and styrene‐butadiene rubber (SBR). The efficient vulcanization (EV) system was employed to minimize the influence of free sulfur in the vulcanizate on the change of the crosslink density. Thermal aging was performed at 40, 60, and 80°C for 20 days with 5‐day intervals. The crosslink densities of the vulcanizates after the thermal aging increase. For the single rubber vulcanizates, variation of the crosslink density by the thermal aging has the order: SBR > BR > NR. For the biblend vulcanizates, variations of the crosslink densities of the NR/SBR and SBR/BR blends are larger than that of NR/BR blend. Variation of the crosslink density of the vulcanizate increases by increasing the SBR content in the vulcanizate. Variation of the crosslink density of the rubber vulcanizate depending on the rubber composition was explained by miscibility of the blends, combination reaction of the pendent groups, and mobility of the pendent group. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 75: 1378–1384, 2000     

Effects of the interaction of hardness,resilience, and fatigue properties on the abrasion properties of rubber blends

The establishment of prediction model for abrasion properties of vulcanizates, based on their simple physio‐mechanical properties, is a hot research field in tribology. The hardness (H), resilience (R), and dynamic fatigue fracture parameters (m) of rubber vulcanizates were combined together in this article, named as hardness–resilience product (H^mR), and its relationships with the abrasion loss for various vulcanizates [natural rubber (NR), styrene–butadiene rubber (SBR), butadiene rubber (BR), and their blends] was investigated by using Akron and DIN abrader. The results showed that, for NR/SBR blends with different SBR content, compared with log(H⁴R), the abrasion loss had much better linear relationship with log(H^mR) for both Akron and DIN abrasion. This good linear relationship, for both Akron and DIN abrasion, also appeared in the SBR/BR blends with different BR content. Furthermore, for both blending systems (NR/SBR and SBR/BR), when all the data above were put together, the abrasion loss also had good linear relationships with its log(H^mR) no matter for Akron or DIN abrasion, which indicated that this linear relationship had some universality. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 130: 1212‐1219, 2013     

Effect of silanized silica nanofiller on tack and green strength of selected filled rubbers

BACKGROUND: Tack and green strength of filled and gum (unfilled) natural rubber (NR), poly(styrene‐co‐butadiene) rubber (SBR), polybutadiene rubber (BR) and (SBR‐BR) blend with different loadings of reinforcement agent, silanized silica nanofiller (Coupsil 8113), were studied and the results compared and discussed. RESULTS: It was found that silica was fully dispersed in rubber matrix after 13 min of mixing. In addition, with some exceptions for NR and (SBR‐BR) blend, filler loading decreased the tack strength of the studied filled rubbers. Green strength and Mooney viscosity increased with filler loading for all studied filled rubbers but with different rates and amounts. The optimum filler loadings for NR and (SBR‐BR) filled blend were 30 and 10 phr, respectively. Tacks of NR filled rubbers were much higher than those of synthetic filled rubbers. CONCLUSION: It was concluded that filler loading alters substantially the tack and green strength of the rubbers under investigation. Copyright © 2009 Society of Chemical Industry     

Morphology and dynamic mechanical properties of natural rubber/nitrile rubber blends containing trans‐polyoctylene rubber as a compatibilizer

The use of trans‐polyoctylene rubber (TOR) as a compatibilizer for blends of natural rubber (NR) and acrylonitrile‐butadiene rubber (NBR) was investigated using atomic force microscopy (AFM) and dynamic mechanical analysis (DMA). The NR/NBR blends containing varying proportions of TOR were prepared in an internal mixer. AFM micrographs of NR/NBR blend at 50/50 (w/w) composition showed heterogeneous phase morphology with NR as a matrix and NBR as a dispersed phase. Inclusion of TOR in the NR/NBR blend altered the phase morphology by reducing the size of the NBR phase. DMA of NR/NBR/TOR showed reduction in tan δ peak height of NBR and an increase in storage modulus E′ in the rubbery region for the NR/NBR blends. A comparison of the E′ obtained from experimental data with that from theoretical models was made to deduce the location of TOR in the blend. Based on the fittings of calculated and experimental values of E′, it was inferred that TOR was incorporated into the NR phase at lower proportion as well as at the interfacial region at higher proportion. The Cole–Cole plot illustrated the compatibilizing effect of TOR. Copyright © 2004 Society of Chemical Industry     

Styrene–butadiene rubber/natural rubber blends: Morphology,transport behavior,and dynamic mechanical and mechanical properties

Blends of styrene–butadiene rubber (SBR) and natural rubber (NR) were prepared and their morphology, transport behavior, and dynamic mechanical and mechanical properties were studied. The transport behavior of SBR/NR blends was examined in an atmosphere of n‐alkanes in the temperature range of 25–60°C. Transport parameters such as diffusivity, sorptivity, and permeability were estimated. Network characterization was done using phantom and affine models. The effect of the blend ratio on the dynamic mechanical properties of SBR/NR blends was investigated at different temperatures. The storage modulus of the blend decreased with increase of the temperature. Attempts were made to correlate the properties with the morphology of the blend. To understand the stability of the membranes, mechanical testing was carried out for unswollen, swollen, and deswollen samples. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 78: 1280–1303, 2000     

Effect of fillers on morphological properties in NR/SBR blends for OTR tyres

Abstract

The blends of styrene butadiene rubber (SBR) and natural rubber (NR) are prepared using a two-roll mixing mill in the presence of different types of carbon blacks as reinforcing filler. The effects of fillers on cure characteristics and thermal, dynamic–mechanical, morphological properties of the blends are studied. The ISAF N231 type of carbon black shows a significant effect on tensile, tear and modulus properties by reacting at the interface between SBR/NR matrixes. The dynamic characteristics and storage modulus of SBR/NR with SAF N110 and SRF N774 types of carbon black show distinct characteristics in respect to all other blends in this system. The thermal stability of the rubber vulcanizates containing SAF N110 and SRF N774 types of carbon blacks is higher than other blend types. With the increasing percentage of SBR to NR, the thermal stability of the blend is increased. However, the heat buildup of the blends increases with the increase in SBR percentage.     

Fractal analysis of worn surfaces of ZnO whisker/natural rubber‐styrene butadiene rubber‐butyl rubber composites

The wear resistance of zinc oxide whisker (ZnOw)/natural rubber‐styrene butadiene rubber‐butyl rubber (NR‐SBR‐BR) composites showed that a tetra‐needle like ZnOw, which is treated by a coupling agent, improved the wear resistance of the rubber composites. The topography of the worn surfaces of the ZnOw/NR‐SBR‐BR composites was fractal, and the fractal dimension and abrasion loss decreased synchronously as the ZnOw content increased in the composites. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 667–670, 2003     

Static deformation of low structure HAF black‐loaded (SBR+NR) rubber blend

The stress‐strain behavior of different concentrations of low‐structure high abrasion furnace black (HAF‐LS, N326)‐loaded rubber blend of styrene butadiene rubber and natural rubber (SBR+NR) of equal parts was measured. Moduli of elasticity and the n‐measure of such blends were calculated using different approaches. An anomaly, of modulus of elasticity, found at 50 phr may be attributed to carbon black reinforcement and to an early crystallization of stretched natural rubber (NR) in the blend. These assumptions are confirmed through the measurement of the swelling factor as a function of time of swelling in kerosene.     

Homogeneous Styrene Butadiene/Acrylonitrile Butadiene Rubber Blends

The graft copolymerization of acrylonitrile (AN) onto butadiene rubber (BR) was carried out in toluene at 80°C, using dibenzoyl-peroxide (BPO) as initiator. The synthesized poly acrylonitrile-grafted-butadiene rubber (AN-g-BR) was characterized by N% elemental analysis and Fourier-transform infrared (FT-IR) spectroscopy. Styrene butadiene rubber/acrylonitrile butadiene rubber (SBR/NBR) blends were prepared with different blend ratios in presence and absence of AN-g-BR, where the homogeneity of such blends were examined with intrinsic viscosity (η) measurements, differential scanning calorimetry (DSC), and scanning electron microscopy (SEM). The scanning electron micrographs illustrate disappearance of the macro-scale phase separation of SBR/NBR rubber blend as a result of the incorporation of AN-g-BR into that blend. Viscosity measurements confirm homogeneity of that blend. Differential Scanning Calorimetry traces exhibit shifts in glass transition temperatures (T _g's) of SBR and NBR in their blend, indicating some degree of homogeneity. Physico-mechanical properties of the rubber blend vulcanizates with different blend ratios, in presence and absence of AN-g-BR, were investigated before and after accelerated thermal aging. The SBR/NBR (25/75) homogeneous blend possessed the best physico-mechanical properties after thermal aging, together with the best swelling behavior in motor oil. The physico-mechanical properties of SBR/NBR (25/75) filled blend with different types of inorganic fillers during thermal aging were studied.     

Kinetics of the phase selective localization of silica in rubber blends

The Fourier transformed infrared (FTIR) spectroscopy on the rubber‐filler gel has been used as a tool for the quantitative characterization of the phase selective silica localization in styrene butadiene rubber (SBR)/natural rubber (NR) blends. The so‐called rubber‐layer L was introduced to describe the selective wetting behavior of the rubber phases to the filler. SBR/NR blends filled with silica were the focus of the experimental investigation. NR shows a higher wetting rate than SBR. Silane addition does not affect the wetting of NR but slowdowns the wetting of SBR. With increasing chamber temperature the value of the rubber‐layer L of all mixtures increases owing to the different thermal activated rubber‐filler bonding processes. Using the wetting concept the kinetics of silica localization in the phases of heterogeneous rubber blends was characterized. Because of the higher wetting rate of the NR component, in the first stage of mixing of NR/SBR blends more silica is found in the NR phase than in the SBR phase. In the next stage, silica is transferred from the NR phase to the SBR phase until the loosely bonded components of NR rubber‐layer are fully replaced by SBR molecules. POLYM. COMPOS., 31:1701–1711, 2010. © 2010 Society of Plastics Engineers.     

Evaluation of curing and physical properties of NR/SBR blends using radiation-grafting copolymer

The curing characterizations of natural rubber (NR) and styrene butadiene rubber (SBR) lattices and their blends with and without NR-g-MA and SBR-g-MA were studied by using oscillating disc rheometer methods. The minimum value for torque decreases with increasing NR in the blends and with the incorporation ofNR-g-MA and SBR-g-MA. The value of maximum torque increases with increasing of SBR in the blend and with the presence of (NR-g-MA and SBR-g-MA) is decreased. The mechanical properties of the samples were studied. The tensile strengths increased steadily with an increase of NR content in the blend. Thermal characteristics of these latex blends were studied by thermogravimetric analysis. Thermal degradation of these individual lattices and their blends were investigated with special reference to blend ratio and vulcanization techniques. As the SBR content in the blends increased their thermal stability was also found to increase. POLYM. COMPOS., 2009. © 2009 Society of Plastics Engineers     

Phase equilibria in SBR/polybutadiene elastomer blends: Application of Flory–Huggins theory

Blends of anionically-polymerized polybutadiene (BR) and styrene–butadiene copolymer (SBR) must be treated as mixtures of terpolymers and tetrapolymers, due to the presence of three different BR isomers: cis-1,4, trans-1,4, and vinyl-1,2. Moreover, in the absence of specific interactions or chemical reactions that strongly influence miscibility, structural characteristics of the component polymers, such as BR isomer content, SBR styrene content, monomer sequence distribution, molecular weight, and molecular weight distribution, are expected to have an increased role in determining the blend miscibility characteristics. Small angle neutron scattering (SANS) studies of SBR/BR blends have resulted in the computation of the monomer–monomer segmental interaction energetics via a Flory–Huggins treatment. This allows quantitative prediction of miscibility behavior as a function of polymer structure. We have used the Flory–Huggins chi parameters, describing the styrene/cis-1,4, styrene/trans-1,4, and cis-1,4/trans-1,4 segmental interactions, to identify certain blend combinations expected to exhibit phase transitions in an experimentally accessible temperature range. The appropriate polymers were synthesized, solution blended, and the blends analyzed via optical microscopy and thermal analysis. Our results show that the blend behavior, observed experimentally, is consistent with the calculated cloud point curves. © 1994 John Wiley & Sons, Inc.     

Influence of compatibilizers on mechanical properties,crystallization, and morphology of polypropylene/scrap rubber dust blends

Polypropylene blends containing a dispersed phase of scrap rubber dusts obtained from sport shoes manufacture; midsole (M, vulcanized EVA foam) and outsole (O, vulcanized rubber blend of NR, SBR, and BR) were studied. The influence of various compatibilizers on the mechanical properties of these blends were investigated. Significant development of impact strength was attained by using 6 and 10 phr of styrene–ethylene–butylene–styrene (SEBS) and maleic anhydride‐grafted styrene–ethylene–butylene–styrene (SEBS‐g‐MA) as compatibilizers for both compounds filled with midsole and outsole dusts. The tensile strength of each compound was slightly decreased when the compatibilizer loading increased, whereas the elongation at break was significantly increased. The enhancements of the impact strength and the elongation at break are believed to arise from reduction of interfacial tension between two phases of the rubber and the PP, which results in some reduction of the particle size of the fillers. Scanning electron microscopy (SEM) confirmed the evidence of the reduction of scrap rubber dust into small rubber particle sizes in the compound, and also showed the occurrence of some fibrils. Optical microscopy (crossed polars) observations suggested that the addition of the rubber dust resulted in a less regular spherulite texture and less sharp spherulite boundaries. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 148–159, 2002     

Segmental mobility in the vicinity of Tg in PS/SBR blends: Nanodomain size prediction of the dispersed phase

The blends of polystyrene (PS) and styrene‐butadiene rubber (SBR) are melt‐blended at different ratios to form physical thermoplastic elastomers. This polymeric blend is expected to behave more or less similar to chemically synthesized block copolymers such as styrene‐butadiene block copolymers (SBS). In this study, mechanical and the thermomechanical properties of this blend are investigated and compared to those of SBS copolymer. As far as morphology is considered, the blend shows a two‐phase morphology with an interface, which shows very weak interactions. According to the observed morphology and the domain size of dispersed phase the blends are of good integrity. The mechanical properties of the blends confirm the integrity of the blend and effective interface stress transfer. The tensile and Izod impact properties of the blends shows improvements upon increase in SBR content of the blend. As SBR content augments the elongation at break increases, whereas tensile dissipated energy and impact resistance go through a maximum. Therefore, blend with SBR‐content in 60–75% range can be considered as preferred one. In a wide range of concentration a phase inversion was observed and T_g‐depression was detected also for the SBR phase. This T_g‐depression was correlated to the changes in dynamics of segments (segmental mobility) near the surfaces. Using the proposed relationships between T_g‐depression and the thickness of the thin films, it was tried to calculate domain size of SBR inclusions in PS matrix. A rough correlation between SBR domain sizes in SEM images and calculated thicknesses using T_g‐depression in thin films was found. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013