Mechanical properties of poly(vinyl chloride) blends and corresponding graft copolymers

The mechanical properties of the poly (vinyl chloride) (PVC) and poly (glycidyl methacrylate) [poly (GMA)] blend system and the PVC and poly (hydroxyethyl methacrylate) [poly (HEMA)] blend system and their crosslinked films were investigated. At the same time, the mechanical properties for the corresponding graft copolymers such as PVC-g-GMA, PVC-g-HEMA, and their crosslinked films were also investigated in this study. The results showed that the tensile strengths for PVC–poly (GMA) blend systems were higher than those for PVC-g-GMA graft copolymer, and the tensile strengths for PVC-g-HEMA were higher than those for PVC-poly (HEMA) blend systems. However, the mechanical properties for the PVC–poly (GMA) blend system were not affected by the crosslinking of the blend system, but those for PVC-poly (HEMA) and their graft copolymers decreased with an increase of the equivalent ratio ([NCO]/[OH]) of the crosslinker. Finally, the surface hydrophilicity of the PVC-g-HEMA graft copolymer and PVC-poly (HEMA) blends were also assessed through measuring the contact angle. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 67: 307–319, 1998     

Properties of interpenetrating polymer network hydrogels composed of poly(vinyl alcohol) and poly(N‐isopropylacrylamide)

Interpenetrating polymer network (IPN) hydrogels based on poly(vinyl alcohol) and poly(N‐isopropylacrylamide) were prepared by the sequential‐IPN method. The IPN hydrogels were analyzed for sorption behavior of water at 35°C and at a relative humidity of 95% using a dynamic vapor sorption system, and water diffusion coefficients were calculated. Differential scanning calorimetry was used for the quantitative determination of the amounts of freezing and nonfreezing water. Free water contents in the IPN hydrogel of IPN1, IPN2, and IPN3 were 45.8, 37.9 and 33.1% in pure water, respectively. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 2041–2045, 2003     

Thermoresponsive sodium alginate‐g‐poly(N‐isopropylacrylamide) copolymers III. Solution properties

Stimuli‐responsive biocompatible and biodegradable materials can be obtained by combining polysaccharides with polymers exhibiting lower critical solution temperature (LCST) phase behavior, such as poly(N‐isopropylacrylamide) (PNIPAAm). The behavior of aqueous solutions of sodium alginate (NaAl) grafted with PNIPAAm (NaAl‐g‐PNIPAAm) copolymers as a function of composition and temperature is presented. The products obtained exhibit a remarkable thermothickening behavior in aqueous solutions if the degree of grafting, the concentration, and the temperature are higher than some critical values. The sol–gel‐phase transition temperatures have been determined. It was found that at temperatures below LCST the systems behave like a solution, whereas at temperatures above LCST, the solutions behave like a stiff gel, because of PNIPAAm segregation. This behavior is reversible and could find applications in tissue engineering and drug delivery systems. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Thermoresponsive behaviour in aqueous solution of poly(maleic acid‐alt‐vinyl acetate) grafted with poly(N‐isopropylacrylamide)

The synthesis of a thermoresponsive graft copolymer consisting of a maleic acid/vinyl acetate alternating copolymer backbone (MAc‐alt‐VA) and poly(N‐isopropylacrylamide) (PNIPAM) side chains is reported. Turbidimetric measurements in dilute aqueous solutions showed that no macroscopic phase separation takes place when the temperature is raised above the lower critical solution temperature (LCST) of PNIPAM, even at pH = 2. Moreover, in semi‐dilute aqueous solutions, a pronounced thermally induced viscosity increase (thermothickening) was observed. This thermoresponsive behaviour has been attributed to the interconnection of the hydrophilic MAc‐alt‐VA graft copolymer backbones by means of the hydrophobic PNIPAM side chain aggregates formed as the temperature increases above the LCST of this polymer. Copyright © 2004 Society of Chemical Industry     

Thermoresponsive poly(ϵ‐caprolactone)‐graft‐poly(N‐isopropylacrylamide) graft copolymers prepared by a combination of ring‐opening polymerization and sequential azide–alkyne click chemistry

A straightforward strategy is described to synthesize poly(?‐caprolactone)‐graft‐poly(N‐isopropylacrylamide) (PCL‐g‐PNIPAAm) amphiphilic graft copolymers consisting of potentially biodegradable polyester backbones and thermoresponsive grafting chains. PCL with pendent chlorides was prepared by ring‐opening polymerization, followed by conversion of the pendent chlorides to azides. Alkyne‐terminated PNIPAAm was synthesized by atom transfer radial polymerization. Then, the alkyne end‐functionalized PNIPAAm was grafted onto the PCL backbone by a copper‐catalyzed azide–alkyne cycloaddition. PCL‐g‐PNIPAAm graft copolymers self‐assembled into spherical micelles comprised of PCL cores and PNIPAAm coronas. The critical micelle concentrations of the graft copolymers were in the range 7.8–18.2 mg L^?1, depending on copolymer composition. Mean hydrodynamic diameters of micelles were in the range 65–135 nm, which increased as the length of grafting chains grew. PCL‐g‐PNIPAAm micelles were thermosensitive and aggregated upon heating. © 2014 Society of Chemical Industry     

Thermal characteristics of interpenetrating polymer networks composed of poly(vinyl alcohol) and poly(N‐isopropylacrylamide)

Interpenetrating polymer networks (IPNs) composed of poly(vinyl alcohol) (PVA) and poly(N‐isopropylacrylamide) (PNIPAAm) were prepared by the sequential‐IPN method. The thermal characterization of the IPNs was investigated using differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), and dielectric analysis (DEA). Depression of the melting temperature (T_m) of the PVA segment in IPNs was observed with increasing PNIPAAm content using DSC. DEA was employed to ascertain the glass‐transition temperature (T_g) of IPNs. From the result of DEA, IPNs exhibited two T_g values, indicating the presence of phase separation in the IPNs. The thermal decomposition of IPNs was investigated using TGA and appeared at near 200°C. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 881–885, 2003     

Thermal degradation behavior of poly(vinyl chloride) in presence of poly(N‐acryloyl‐N′‐cyanoacetohydrazide)

The thermal degradation behavior of poly (vinyl chloride), PVC, in presence of poly(N‐acryloyl‐N′‐cyanoacetohydrazide), PACAH, has been studied using continuous potentiometric determination of the evolved HCl gas from the degradation process from one hand and by measuring the extent of discoloration of the degraded samples from the other. The efficiency of blending PACAH with dibasic lead carbonate, DBLC, conventional thermal stabilizer has also been investigated. A probable radical mechanism for the effect of PACAH on the thermal stabilization of PVC has been proposed. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Poly(N‐isopropylacrylamide‐co‐hydroxyethyl methacrylate) graft copolymers and their application as carriers for drug delivery system

Poly(N‐isopropylacrylamide‐co‐hydroxyethyl methacrylate) [P(NIPAM‐co‐HEMA)] copolymer was synthesized by controlled radical polymerization from respective N‐isopropylacrylamide (NIPAM) and hydroxyethyl methacrylate (HEMA) monomers with a predetermined ratio. To prepare the thermosensitive and biodegradable nanoparticles, new thermosensitive graft copolymer, poly(L ‐lactide)‐graft‐poly(N‐isoporylacrylamide‐co‐hydroxyethyl methacrylate) [PLLA‐g‐P(NIPAM‐co‐HEMA)], with the lower critical solution temperature (LCST) near the normal body temperature, was synthesized by ring opening polymerization of L ‐lactide in the presence of P(NIPAM‐co‐HEMA). The amphiphilic property of the graft copolymers was formed by the grafting of the PLLA hydrophobic chains onto the PNIPAM based hydrophilic backbone. Therefore, the graft copolymers can self‐assemble into uniformly spherical micelles ò about 150–240 nm in diameter as observed by the field emission scanning electron microscope and dynamic light scattering. Dexamethasone can be loaded into these nanostructures during dialysis with a relative high loading capacity and its in vitro release depends on temperature. Above the LCST, most of the drugs were released from the drug‐loaded micelles, whereas a large amount of drugs still remains in the micelles after 48 h below the LCST. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Thermosensitive fibres of lyocell/poly(N‐isopropylacrylamide): multiparametric analysis for studying the graft copolymerization

The thermosensitive properties of the hydrogel poly(N‐isopropylacrylamide) (pNIPAAm) together with the good mechanical properties of lyocell fibres make a combination of the two to be thought of as a smart textile. In the present study the optimal values of various parameters that control the grafting process of pNIPAAm onto lyocell fibres were determined considering the influence of the interaction between them. The copolymerization of pNIPAAm hydrogel onto lyocell fibres was performed in aqueous acidic medium using cerium(IV) as initiator. An experimental design was planned in order to study the effect of the interactions between some variables that affect the kinetics of the graft copolymerization: the cerium(IV) initiator concentration, the N‐isopropylacrylamide (NIPAAm) monomer concentration and the liquor fibre‐to‐bath ratio. The results show that the interaction between the concentrations of NIPAAm and the initiator significantly affects the degree of grafting (DG), the optimum values being 1250 and 12.25 mmol L^?1, respectively. In contrast, the liquor ratio parameter shows no significant interaction with the other two variables studied, meaning that it acts independently but showing a proportional relationship with respect to the DG obtained. In addition, the presence of pNIPAAm in the copolymer obtained was confirmed by Fourier transform infrared spectral analysis. Moreover, the water sorption capacity, depending on the temperature, of the lyocell/pNIPAAm copolymer was studied, with an increase being observed when the DG is higher than 60% and also increasing with the temperature.© 2012 Society of Chemical Industry     

Poly(N‐isopropylacrylamide)‐grafted silica as a support of platinum colloids: Preparation method,characterization, and catalytic properties in hydrogenation

We investigated the composition, properties, and utility of a novel hybrid material of poly(N‐isopropylacrylamide)‐grafted silica. The modified silica was prepared in two steps: (1) grafting silane layers of active precursors, such as initiator, transfer agent or comonomer onto the silica surface by solution deposition and (2) radical polymerization of N‐isopropylacrylamide (NIPAAm) on the grafted silane layers. Thermogravimetric analysis (TGA), elemental analysis (EA), FTIR spectroscopy, and TEM were used to characterize the layer composition, structure, and chemistry, respectively. Well‐dispersed platinum colloids have been prepared on the PNIPAAm‐grafted silica via the reduction of PtCl by ethanol. The immobilized Pt colloids were found to be active and stable heterogeneous catalysts for the hydrogenation of ally alcohol in ethanol. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 77: 2678–2684, 2000     

Binary blends based on poly(N‐isopropylacrylamide): Miscibility studies with PVA,PVP, and PAA

Blends of poly(vinyl alcohol) (PVA), poly(acrylic acid), (PAA), and poly(vinyl pyrrolidone) (PVP), with poly(N‐isopropylacrylamide) (PNIPAM), were prepared by casting from aqueous solutions. Mechanical properties of PNIPAM/PVA blends were analyzed by stress–strain tests. Differential scanning calorimetry (DSC) and scanning electron microscopy (SEM) were employed to analyze the miscibility between the polymeric pairs. The results revealed that PNIPAM is not miscible with PVA and PVP in the whole range of composition. On the other hand, PNIPAM interacts strongly with PAA forming interpolymer complex due to the formation of cooperative hydrogen bonds. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 743–748, 2004     

Preparation of chlorinated poly(vinyl chloride)‐g‐poly(N‐vinyl‐2‐pyrrolidinone) membranes and their water permeation properties

Chlorinated poly(vinyl chloride) (CPVC) membranes for microfiltration processes were prepared with the combined process of a solvent evaporation technique and the water‐vapor induced‐phase‐inversion method. CPVC membranes with a mean pore size of 0.7 μm were very hydrophobic. These membranes were subjected to surface modification by ultraviolet (UV)‐assisted graft polymerization with N‐vinyl‐2‐pyrrolidinone (NVP) to increase their surface wettability and decrease their adsorptive fouling. The grafting yields of the modified membranes were controlled by alteration of UV irradiation time and NVP monomer concentration. The changes in chemical structure between the CPVC membrane and the CPVC‐g‐poly(N‐vinyl‐2‐pyrrolidinone) membrane and the variation of the topologies of the modified PVC membranes were characterized by Fourier transform infrared spectroscopy, gel permeation chromatography, and field emission scanning electron microscopy. According to the results, the graft yield of the modified CPVC membrane reached a maximum at 5 min of UV exposure time and 20 vol % NVP concentration. The filtration behavior of these membranes was investigated with deionized water by a crossflow filtration measurement. The surface hydrophilicity and roughness were easily changed by the grafting of NVP on the surface of the CPVC membrane through a simultaneous irradiation grafting method by UV irradiation. To confirm the effect of grafting for filtration, we compared the unmodified and modified CPVC membranes with respect to their deionized water permeation by using crossflow filtration methods. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 3188–3195, 2003     

Thermal characterizations of semi‐interpenetrating polymer networks composed of poly(ethylene oxide) and poly(N‐isopropylacrylamide)

Poly(N‐isopropylacrylamide) (PNIPAAm)/poly(ethylene oxide) (PEO) semi‐interpenetrating polymer networks (semi‐IPNs) synthesized by radical polymerization of N‐isopropylacrylamide (NIPAAm) in the presence of PEO. The thermal characterizations of the semi‐IPNs were investigated by differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), and dielectric analysis (DEA). The melting temperature (T_m) of semi‐IPNs appeared at around 60°C using DSC. DEA was employed to ascertain the glass transition temperature (T_g) and determine the activation energy (E_a) of semi‐IPNs. From the results of DEA, semi‐IPNs exhibited one T_g indicating the presence of phase separation in the semi‐IPN, and T_gs of semi‐IPNs were observed with increasing PNIPAAm content. The thermal decomposition of semi‐IPNa was investigated using TGA and appeared at around 370°C. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 3922–3927, 2003     

Network parameters and volume phase transition behavior of poly(N‐isopropylacrylamide) hydrogels

Thermosensitive hydrogels were prepared by free radical polymerization in aqueous solution from N‐isopropylacrylamide (NIPA) monomer and N,N‐methylenebis(acrylamide) (MBAAm) crosslinker. The swelling equilibrium of the hydrogels in deionized water was investigated as a function of temperature and MBAAm content. The results indicated that the swelling behavior and temperature sensitivity of the hydrogels were affected by the amount of MBAAm content. The average molecular mass between crosslinks and polymer–solvent interaction parameter (χ) of the hydrogels were determined from equilibrium swelling values. The swelling variations were explained according to swelling theory based on the hydrogel chemical structure. The swelling equilibrium of the hydrogels was also investigated as a function of temperature in aqueous solutions of the anionic surfactant sodium dodecyl sulfate (SDS) and the cationic surfactant dodecyltrimethylammonium bromide (DTAB). In deionized water, the hydrogels showed a discontinuous volume phase transition at 32°C. In SDS and DTAB solutions, the equilibrium swelling ratio and the volume phase transition temperature (lower critical solution temperature) of the hydrogels increased, which is ascribed to the conversion of nonionic PNIPA hydrogel into polyelectrolyte hydrogels because of binding of surfactant molecules through the hydrophobic interaction. Additionally, the amount of free SDS and DTAB ions was measured at different temperatures by a conductometric method; it was found that the electric conductivity of the PNIPA–surfactant systems depended strongly on both the type and concentration of surfactant solutions. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 1756–1762, 2006     

Microwave‐assisted preparation of temperature sensitive poly(N‐isopropylacrylamide) hydrogels in poly(ethylene oxide)‐600

In this article, a series of poly(N‐isopropylacrylamide) (PNIPAM)‐based hydrogels were prepared under microwave irradiation using poly(ethylene oxide)‐600 (PEO‐600) as reaction medium and microwave‐absorbing agent as well as pore‐forming agent. All of the temperature measurements, gel fractions, and FTIR analyses proved that the PNIPAM hydrogels were successfully synthesized. Within 1 min, the PNIPAM hydrogel with a 98% yield was obtained under microwave irradiation. The PNIPAM hydrogels thus prepared exhibited controllable properties such as pore size, equilibrium swelling ratios, and swelling/deswelling rates when changing the feed weight ratios of monomer (N‐isopropylacrylamide, NIPAM) to PEO‐600. These properties are well adapted to the different requirements for their potential application in many fields such as biomedicine. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102:4177–4184, 2006     

梳型接枝PVC的制备

研究了聚氯乙烯与肉豆蔻酸钠的接枝反应,并制备梳形接枝PVC。利用FT-IR、1H-NMR对梳型接枝PVC的结构进行表征,并探讨反应条件对接枝率的影响。结果表明,梳形侧链成功接枝到PVC上,且在反应温度70℃、反应时间9h、单体用量50%时,接枝率最高。     

Preparation and characterization of thermosensitive poly(N‐isopropylacrylamide)/poly(ethylene oxide) semi‐interpenetrating polymer networks

Temperature‐sensitive poly(N‐isopropylacrylamide) hydrogels were successfully synthesized by using poly(ethylene oxide) as the interpenetrating agent. The newly prepared semi‐interpenetrating polymer network (semi‐IPN) hydrogels exhibited much better properties as temperature‐sensitive polymers than they did in the past. Characterizations of the IPN hydrogels were investigated using a swelling experiment, FTIR spectroscopy, and differential scanning calorimetry (DSC). Semi‐IPN hydrogels exhibited a relatively high temperature dependent swelling ratio in the range of 23–28 at room temperature. DSC was used for the determination of the lower critical solution temperature of the semi‐IPN hydrogel. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 3032–3036, 2003     

Preparation and properties of temperature‐sensitive soy protein/poly(N‐isopropylacrylamide) interpenetrating polymer network hydrogels

Temperature‐sensitive interpenetrating polymer network (IPN) hydrogels based on soy protein and poly(N‐isopropylacrylamide) were successfully prepared. The structure and properties were systematically characterized using Fourier transform infrared spectroscopy, scanning electron microscopy, differential scanning calorimetry and thermogravimetric analysis, and the swelling and deswelling behavior was also investigated. It was found that the hydrogels had good miscibility, thermal stability and temperature sensitivity, and the lower critical solution temperature was ca 32 °C. Changing the content of soy protein or crosslinker could be used to control the swelling behavior, water retention and network structure of the IPN hydrogels. The results show that the novel IPN hydrogels may be of potential interest in drug delivery systems. Copyright © 2011 Society of Chemical Industry     

Temperature‐responsive characteristics of poly(N‐isopropylacrylamide) hydrogels with macroporous structure

Macroporous poly(N‐isopropylacrylamide) (PNIPA) hydrogels were synthesized by free‐radical crosslinking polymerization in aqueous solution from N‐isopropylacrylamide monomer and N,N‐methylenebis (acrylamide) crosslinker using poly(ethylene glycol) (PEG) with three different number‐average molecular weights of 300, 600 and 1000 g mol^?1 as the pore‐forming agent. The influence of the molecular weight and amount of PEG pore‐forming agent on the swelling ratio and network parameters such as polymer–solvent interaction parameter (χ) and crosslinking density (ν_E) of the hydrogels is reported and discussed. Scanning electron micrographs reveal that the macroporous network structure of the hydrogels can be adjusted by applying different molecular weights and compositions of PEG during polymerization. At a temperature below the volume phase transition temperature, the macroporous hydrogels absorbed larger amounts of water compared to that of conventional PNIPA hydrogels, and showed higher equilibrated swelling ratios in aqueous medium. Particularly, the unique macroporous structure provides numerous water channels for water diffusion in or out of the matrix and, therefore, an improved response rate to external temperature changes during the swelling and deswelling process. These macroporous PNIPA hydrogels may be useful for potential applications in controlled release of macromolecular active agents. Copyright © 2006 Society of Chemical Industry     

Rheological behavior and thermal properties of poly(butyl acrylate‐co‐2‐ethylhexyl acrylate)‐grafted vinyl chloride resin

The rheological behavior and thermal properties of a poly(butyl acrylate‐co‐2‐ethylhexyl acrylate) [P(BA‐EHA)]‐grafted vinyl chloride (VC) composite resin [P(BA‐EHA)/poly(vinyl chloride) (PVC)] and its materials were investigated. The rheological behavior, thermal stability, and Vicat softening temperature (VST) of P(BA‐EHA)/PVC were measured with capillary rheometry, thermal analysis, and VST testing, respectively. The effects of the P(BA‐EHA) content and the polymerization temperature of grafted VC on the rheological behavior of the composite resin were examined. The weight loss of the composite resin and its extracted remainder via heating were analyzed. The influence of the content and crosslinking degree of P(BA‐EHA) and the polymerization temperature of the grafted VC on VST of the materials was determined. The results indicated the pseudoplastic‐flow nature of the composite resin. The flow property of the modified PVC resin was improved because of the incorporation of the acrylate polymer. The molecular weight of PVC greatly influenced the flow behavior and VST of the composite resin and its materials. The flowability of the composite resin markedly increased, and the VST of its materials decreased as the polymerization temperature of the grafted VC increased. The initial degradation temperature of the composite resin increased as the P(BA‐EHA) content increased. The VST of the samples was enhanced a little as the content of the crosslinking agent increased in P(BA‐EHA). As expected, the composite resin, with good impact resistance, had better heating stability and flowability than pure PVC, whereas the VST of the material decreased little with increasing P(BA‐EHA) content. Therefore, P(BA‐EHA)/PVC resins prepared by seeded emulsion polymerization have excellent potential for widespread applications. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 95: 419–426, 2005