Casting solvent effect on crystallization behavior of poly(vinyl acetate)/poly(ethylene oxide) blends: DSC study

Poly(vinyl acetate) (PVAc)/poly(ethylene oxide) (PEO) blends were prepared by casting from either benzene or chloroform. The solvent effects on the crystallization behavior and thermodynamic properties of the blends were studied by the differential scanning calorimeter (DSC). Two grades of PEO with different molecular weights (PEO200 with M_w = 200,000 g/mol and PEO2 with M_n = 2000 g/mol) were used in this work. The thermal analysis revealed that the blends cast from either benzene or chloroform were miscible in the molten state. The crystallization of PEO in the benzene-cast blends was more easily suppressed than it was in the chloroform-cast blends. Furthermore, the benzene-cast blends showed a greater negative value of Flory-Huggins interaction parameter than those cast from chloroform in the PVAc/PEO200 poly-blend system. It was supposed that the benzene-cast blends had more homogeneous morphology. © 1997 John Wiley & Sons, Inc. J Appl Polym Sci 64: 411–421, 1997     

Miscible blends of poly(4‐vinyl phenol)/poly (trimethylene terephthalate)

A new miscible blend of all compositions comprising poly(4‐vinyl phenol) (PVPh) and poly(trimethylene terephthalate) (PTT) was discovered and reported. The blends exhibit a single composition‐dependent glass transition and homogeneous phase morphology, with no lower critical solution temperature (LCST) behavior upon heating to high temperatures. Interactions and spherulite growth kinetics in the blends were also investigated. The Flory–Huggins interaction parameter (χ₁₂) and interaction energy density (B) obtained from analysis of melting point depression are negative (χ₁₂ = ?0.74 and B = ?32.49 J cm^?3), proving that the PVPh/PTT blends are miscible over a wide temperature range from ambient up to high temperatures in the melt state. FTIR studies showed evidence of hydrogen‐bonding interactions between the two polymers. The miscibility of PVPh with PTT also resulted in a reduction in spherulite growth rate of PTT in the miscible blend. The Lauritzen–Hoffman model was used to analyze the spherulite growth kinetics, which showed a lower fold‐surface free energy (σ_e) of the blends than that of the neat PTT. The decrease in the fold‐surface free energy has been attributed to disruption of the PTT lamellae exerted by PVPh in an intimately interacted miscible state. Copyright © 2004 Society of Chemical Industry     

Studies on dielectric relaxation and ac conductivity of cellulose acetate hydrogen phthalate–poly (vinyl pyrrolidone) blend

The dielectric constant, dielectric loss, and ac conductivity of polyblends of cellulose acetate hydrogen phthalate (CAP) and poly (vinyl pyrrolidone) (PVP) of different compositions were measured in the temperature range of 300–430 K and in the frequency range of 50 Hz–100 kHz. In the blends, the dielectric constant as well as the dielectric loss as a function of the temperature display a single peak corresponding to the glass transition temperature (T_g) in the region between the T_g values of the pure polymers. The T_g values observed agree well with those values obtained from DSC. Dielectric studies show that CAP forms a miscible blend with PVP. Ac conductivity values were calculated from the dielectric data and the conduction mechanism is discussed. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 1702–1708, 2002     

Blended graft copolymer of carboxymethyl cellulose and poly(vinyl alcohol) with banana fiber

Conducting hydrogel copolymer was prepared by graft copolymerization of carboxymethyl cellulose (CMC) and boric acid onto poly(vinyl alcohol) (PVA). The dielectric properties of CMC‐g‐PVA/prehydrolyzed banana blend have been investigated as a function of frequency, with special reference to pure prehydrolyzed banana. Also, the static bending for the blend was determined and no abrupt failure was observed. The dielectric properties measured were dielectric constant (ε′), dissipation factor (tan δ), and loss factor (ε″). At high frequencies, a transition in the relaxation behavior was observed, whereby the dielectric constant, loss tangent, and loss factor decreased with frequency. Experimental ε′ values of the blend are greater than those of prehydrolyzed banana. The dielectric behavior depends greatly on the nature of the present group, the crystallinity of the system, and the degree of hydrogen bonding between the different chains. The variation of the dielectric properties was correlated with blend morphology and also to the possibility for interfacial polarization that arises because of the differences in conductivities of the two phases. It was found from the infrared spectra that the incorporation of CMC‐g‐PVA copolymer decreases the crystallinity of the blend and also decreases the degree of hydrogen bonding, which results in a high dielectric constant. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 1842–1848, 2006     

Miscibility of biodegradable aliphatic polyester and poly(vinyl acetate) blends

We report miscibility behavior for synthetic biodegradable aliphatic polyester (BDP) and poly(vinyl acetate) (PVAc) blends by investigating their thermal, rheological, and mechanical properties. Two separate glass transition temperature peaks for the BDP/PVAc blends proved that these blend systems are immiscible. From the rheological measurement, the shear viscosity as a function of shear rate is observed to increase with increasing PVAc content in BDP/PVAc blends, since PVAc has a relatively high molecular weight compared to BDP. Moreover, BDP blends with 10 wt % PVAc have excellent mechanical properties. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 77: 1348–1352, 2000     

Fourier transform infrared spectroscopic studies of the poly(styrene-co-acrylonitrile) and poly (vinyl chloride-co-vinyl acetate) blends

The Fourier transform infrared (FTIR) spectroscopic studies of the poly-(styrene-co-acrylonitrile) (SAN) and poly(vinyl chloride-co-vinyl acetate) (VYHH) blends produced by different blending techniques, viz., solution blending, melt-blending, and also the co-precipitation methods of blending, were performed. In the case of miscible blend systems, substantial band shiftings took place, whereas immiscible blend systems showed slight or no band shifting. The miscible blends showed a substantial residual spectrum which was absent in the case of the immiscible system when a similar subtraction process was carried out. © 1997 John Wiley & Sons, Inc. J Appl Polym Sci 63: 991–1000, 1997     

Studies on miscibility of blends of poly (ethylene acrylic acid) and ethylene‐co‐vinyl acetate by melt rheology

Rheological behavior of blends of poly (ethylene‐acrylic acid) (EAA) and ethylene vinyl acetate (EVA) copolymer have been carried out at various temperatures, namely, 100, 110, and 120°C, and different shear rates from 61.33 to 613.30 s^?1 using a Monsanto Processability Tester. The melt viscosity of the blends shows synergism during processing. The activation energy of the blends is in the range 20.7–44.6 kJ/mol. Highest activation energy was observed for the blends containing 40–60% of EVA by weight. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 98: 1947–1954, 2005     

Effect of ester group bulkiness of polyacrylates on miscibility with poly(vinyl acetate)

BACKGROUND: The miscibility of poly(vinyl acetate) (PVAc) with a series of polyacrylates, namely poly(methyl acrylate) (PMA), poly(ethyl acrylate) (PEA) and poly(butyl acrylate) (PBA), with ester chains of varying bulkiness was studied from both qualitative and quantitative points of view. RESULTS: The evidence from thermal (differential scanning calorimetry) and Fourier transform infrared analyses demonstrates that the miscibility of PVAc with the polyacrylates is rapidly reduced on increasing the bulkiness of their ester chains. Miscibility is quantitatively discussed in the framework of the corresponding states theory applying the approximate Patterson form. For this reason the characteristic values of volume, temperature and pressure were preliminarily evaluated both experimentally, through dilatometric measurements, and by calculations. At the same time, calorimetric measurements allowed the evaluation of the enthalpies of mixing of the components. CONCLUSION: The conclusions reached with this approach are that polar interactions are active among the repeat units of the blend components, but the intensities of these forces are progressively reduced by the shielding of the apolar groups of the polyacrylates. The steric hindrance of the hydrocarbon groups shields the interactions of the polar groups of PVAc with the COOR moieties of the acrylates, so that the miscibility progressively decreases from PMA to PEA to PBA. Copyright © 2009 Society of Chemical Industry     

Preparation and characterization of chitosan/poly(vinyl alcohol) blend fibers

Chitosan and poly(vinyl alcohol) blend fibers were prepared by spinning their solution through a viscose‐type spinneret at 25°C into a coagulating bath containing aqueous NaOH and ethanol. The influence of coagulation solution composition on the spinning performance was discussed, and the intermolecular interactions of blend fibers were studied by infrared analysis (IR), X‐ray diffraction (XRD), and scanning electron micrograph (SEM) and by measurements of mechanical properties and water‐retention properties. The results demonstrated that the water‐retention properties and mechanical properties of the blend fibers increase due to the presence of PVA in the chitosan substract, and the mechanical strength of the blends is also related to PVA content and the degree of deacetylation of chitosan. The best mechanical strength values of the blend fibers, 1.82 cN/d (dry state) and 0.81 cN/d (wet state), were obtained when PVA content was 20 wt % and the degree of deacetylation of chitosan was 90.2%. The strength of the blend fibers, especially wet tenacity could be improved further by crosslinking with glutaraldehyde. The water‐retention values (WRV) of the blend fibers were between 170 and 241%, obviously higher than pure chitosan fiber (120%). The structure analysis indicated that there are strong interaction and good miscibility between chitosan and poly(vinyl alcohol) molecular resulted from intermolecular hydrogen bonds. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 80: 2558–2565, 2001     

Studies of polyester/chlorinated poly(vinyl chloride) blends

Chlorinated poly(vinyl chloride) (CPVC) was solution blended with poly(caprolactone) (PCL), poly(hexamethylene sebacate) (PHMS), poly(α-methyl-α-n-propyl-β-propiolactone) (PMPPL), poly(valerolactone) (PVL), poly(ethylene adipate), poly(ethylene succinate) and poly(β-propiolactone). From calorimetric glass transition temperature (T_g) measurements, it is concluded that CPVC is miscible with polyesters having a CH₂/COO ratio larger than three (PCL, PHMS, PMPPL and PVL). The Gordon-Taylor k parameter was also calculated and found equal to 1.0 and 0.56 for PCL/CPVC and PHMS/CPVC blends, respectively. From these values, it is concluded that CPVC gives a stronger interaction with polyesters than poly(vinyl chloride) due to its larger chlorine content.     

Miscible blends of poly(butyl methacrylate) densely grafted on fumed silica with poly(vinyl chloride)

Poly(butyl methacrylate) (PBMA) densely grafted on a fumed silica particle consisting of primary particles with an average diameter of 14 nm, has been synthesized by surface-initiated atom transfer radical polymerization (SI-ATRP). In these syntheses, a newly designed initiator, p-(bromomethyl)benzyl 2-bromoisobutylate was used for the immobilization of the initiator moiety on the silica particle to give the densely grafted PBMA. Thus synthesized nanocomposites have exhibited unusual miscibility with poly(vinyl chloride) (PVC) through differential scanning calorimetry (DSC). The derivative DSC peaks for the composite/PVC blends were significantly different from those for the conventional PBMA/PVC blends. This interesting finding is due to a wide gradient of the PVC concentration on a microscopic scale, resulting from the densely grafted PBMA chains; the PBMA component is enriched near the surface of the fumed silica, while the PVC component is enriched far from the surface. This gradient miscible state is strongly supported by dynamic mechanical analysis. Furthermore, a synergistic effect on storage modulus was seen in the nanocomposite/PVC blends.     

Miscible blends of styrene–cinnamic acid copolymers with poly(ethyl methacrylate)

Differential scanning calorimetry and inverse gas chromatography have been used to investigate the miscibility behaviour of blends of poly(ethyl methacrylate) (PEMA) with styrene–cinnamic acid statistical copolymers PSCA5, PSCA8, PSCA23 having compositions of, respectively, 5, 8 and 23 mol% of cinnamic acid. Several probes with different chemical nature and polarity have been used to determine the polymer–solute and polymer–polymer interaction parameters. DSC and CPGI measurements indicate that poly(ethyl methacrylate) is miscible with each poly[(styrene)‐co‐(cinnamic acid)] copolymer as established from the observation of a single composition‐dependent glass transition temperature. This deduction is corroborated by the IGC data; comparison of the experimental retention volume of the blend with the algebraic average retention volumes of the pure components, together with negative values of the apparent polymer–polymer interaction parameter, establish the miscibility of the studied systems. Furthermore, the polymer–polymer interaction parameters are found to show marked probe dependence; this is discussed in terms of the Δχ effect. As indicated by the variation of the glass transition temperature with blend composition, the application of the Kwei and the Schneider approaches to the calorimetric results suggests the occurrence of strong specific interactions within the blends; the strength of these intermolecular interactions increases with the cinnamic acid content in the PSCA copolymer. © 2001 Society of Chemical Industry     

Mapping phases of poly(vinyl alcohol) and poly(vinyl acetate) blends by FTIR microspectroscopy and optical fluorescence microscopy

Fluorescence optical microscopy (FOM) of poly(vinyl alcohol) (PVA) and poly(vinyl acetate) (PVAc) blends in compositions 9/1, 1/1, and 1/9 (w/w) show that these blends present phase separation in the solid state. Each domain of the solid samples was identified by FOM as PVA-richer domains by green fluorescence of fluorescein and PVAc-richer domains by the blue fluorescence of anthracene. The dimensions, shapes, and distributions of these domains were dependent on the initial composition of the polymeric mixtures in the solution. Specific interactions between both homopolymers were studied using FTIR microspectroscopy, which allowed us to obtain spectra for both PVA-richer and PVAc-richer domains. These spectra demonstrated that partial miscibility could occur only for blends with a higher PVAc content and, in these cases, we observed interchain hydrogen-bonded carbonyl groups. Fluorescence microscopy of blends with this partial miscibility exhibited small interconnected domains produced by coalescence of droplets during the polymer phase separation process. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 69: 645–655, 1998     

Miscibility and thermal behavior of poly(vinyl chloride)/feather keratin blends

Various poly(vinyl chloride) (PVC)/feather keratin (FK) blends were prepared via a solution blending method in the presence of N,N‐dimethylformamide as a solvent. The miscibility of the blends was studied with different analytical methods, such as dilute solution viscometry, differential scanning calorimetry, refractometry, and atomic force microscopy. According to the results obtained from these techniques, it was concluded that the PVC/FK blend was miscible in all the studied compositions. Specific interactions between carbonyl groups of the FK structure and hydrogen from the chlorine‐containing carbon of the PVC were found to be responsible for the observed miscibility on the basis of Fourier transform infrared spectroscopy. Furthermore, increasing the FK content in the blends resulted in their miscibility enhancement. The thermal stability of the samples, as an important characteristic of biobased polymer blends, was finally examined in terms of their FK weight percentage and application temperature. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Miscible blends of poly(vinyl phenyl ketone hydrogenated) and poly(styrene-co-4-vinylpyridine)

Miscibility behavior over a wide composition range was detected for polymer blends of poly(vinyl phenyl ketone hydrogenated) (PVPhKH) with poly(styrene-co-4-vinylpyridine) (PS-co-4VPy). Differential scanning calorimetry (DSC) and thermo mechanical analysis (TMA) reveal that each composition has only one glass transition temperature. The variation of the glass transition temperature with composition for PVPhKH/PS-co-4VPy miscible blends follows the Gordon-Taylor equation. FTIR analysis of this binary system indicates the existence of hydrogen bonding between pyridine ring of PS-co-4VPy and hydroxyl groups insert into PVPhKH. This specific interaction has a decisive influence in the phase behavior of PVPhKH/PS-co-4VPy blends.     

Miscible blends containing bacterial poly(3‐hydroxyvalerate) and poly(p‐vinyl phenol)

The miscibility of poly(3‐hydroxyvalerate) (PHV)/poly(p‐vinyl phenol) (PVPh) blends has been studied by differential scanning calorimetry (DSC) and Fourier transform infrared (FTIR) spectroscopy. The blends are miscible as shown by the existence of a single glass transition temperature (T_g) and a depression of the equilibrium melting temperature of PHV in each blend. The interaction parameter was found to be −1.2 based on the analysis of melting point depression data using the Nishi–Wang equation. Hydrogen‐bonding interactions exist between the carbonyl groups of PHV and the hydroxyl groups of PVPh as evidenced by FTIR spectra. The crystallization of PHV is significantly hindered by the addition of PVPh. The addition of 50 wt % PVPh can totally prevent PHV from cold crystallization. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 74: 383–388, 1999     

Effect of bisphenol A on the miscibility,phase morphology,and specific interaction in immiscible biodegradable poly(ε‐caprolactone)/poly(L‐lactide) blends

We have investigated the enhancement in miscibility, upon addition of bisphenol A (BPA) of immiscible binary biodegradable blends of poly(ε‐caprolactone) (PCL) and poly(L ‐lactide) (PLLA). That BPA is miscible with both PCL and PLLA was proven by the single value of T_g observed by differential scanning calorimetry (DSC) analyses over the entire range of compositions. At various compositions and temperatures, Fourier transform infrared spectroscopy confirmed that intermolecular hydrogen bonding existed between the hydroxyl group of BPA and the carbonyl groups of PCL and PLLA. The addition of BPA enhances the miscibility of the immiscible PCL/PLLA binary blend and transforms it into a miscible blend at room temperature when a sufficient quantity of the BPA is present. In addition, optical microscopy (OM) measurements of the phase morphologies of ternary BPA/PCL/PLLA blends at different temperatures indicated an upper critical solution temperature (UCST) phase diagram, since the ΔK effect became smaller at higher temperature (200°C) than at room temperature. An analysis of infrared spectra recorded at different temperatures correlated well with the OM analyses. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 1146–1161, 2006     

Rheological studies of the poly(styrene-co-acrylonitrile) and poly(vinyl chloride-co-vinyl acetate) blends

The rheological studies of the poly(vinyl chloride-co-vinyl acetate) and poly(styrene-co-vinyl acetate) and poly(styrene-co-acrylonitrile) blends were performed by a Brabender Rheotron at three different temperatures and also at different shear rates. Flow curves of the blends at different temperatures were drawn. The flow behavior index and, also, zero-shear viscosity of the blends at different temperatures were determined. From the flow curves, it has been found that as shear stress increases, melt viscosity decreases at all temperatures, indicating that pseudoplastic behavior and experimental values lies above the line of the log-additivity value and below the line of the additivity rule of mixture. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 69: 2577–2583, 1998     

Miscibility and mechanical properties of poly(styrene-co-4-vinylpyridine) and poly(butyl acrylate-co-acrylic acid) ionomer blends

The miscibility of polystyrene with poly(butyl acrylate) is very poor. Ionic interactions have been utilized recently as miscibility enhancers. In this paper, dynamic mechanical studies indicate that ion pair–ion pair interactions can be utilized to achieve miscibility in blends of polystyrene and poly(butyl acrylate). The styrenes contain 0–15mol% quaternary ammonium salt of 4-vinylpyridine, while the butyl acrylates contain 0–15mol% potassium acrylate groups. The miscibility increases with increase of ion content. When the ion content exceeds 11mol%, the polymers can be completely miscible. The mechanical properties of the ionomers and their blends were also studied. The results indicate that the tensile strength of ionomer blends is higher than that of corresponding poly(butyl acrylate-co-potassium acrylate)s (PBA-AA-K). The elongation at break of ionomer blends is higher than that of the corresponding poly(styrene-co-N-methyl-4-vinylpyridinium iodide) (PS-4VP-Q). © 1998 SCI.