Morphology of pyrolyzed polystyrene–isoprene–styrene and polystyrene–butadiene–styrene block copolymers

The surface morphology of thermooxidative‐degraded polystyrene–isoprene–styrene (SIS) and polystyrene–butadiene–styrene (SBS) thermoplastic block copolymers were studied by scanning electron microscopy. Surface changes caused by heating the samples in a pyrolizer for 15 and 30 min were presented in different micrographs. The morphological changes occurring due to the formation of polar groups and their crossing linking during the thermooxidative degradation are discussed. Morphological study of these thermally degraded polymer samples show very good correlation with the thermodegradation results. The rate of thermodegradation is fast in case of SBS compared with SIS block copolymer. ©2005 Wiley Periodicals, Inc. J Appl Polym Sci, 2006     

Morphology of pyrolysed polystyrene–isoprene–styrene and polystyrene–butadiene–styrene block copolymers

The surface morphology of thermooxidative degraded polystyrene–isoprene–styrene (SIS) and polystyrene–butadiene–styrene (SBS) thermoplastic block copolymers was studied by scanning electron microscopy. Surface changes caused by heating the samples in a pyrolyzer for 15 and 30 min were presented in different micrographs. The morphological changes occurring due to the formation of polar groups and their crosslinking during the thermooxidative degradation are discussed. Morphological study of these thermally degraded polymer samples shows very good correlation with the thermodegradation results. The rate of thermodegradation is fast in case of SBS when compared with SIS block copolymer. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 99: 2549–2553, 2006     

Blends of styrene–butadiene–styrene triblock copolymer and isotactic polypropylene: morphology and thermomechanical properties

A set of blends of styrene–butadiene–styrene triblock copolymer (SBS) and isotactic polypropylene (i‐PP) in a composition range 0–100 % polypropylene by weight was prepared in a twin screw extruder. The morphology of the blends has been studied by transmission electron microscopy. The blends present phase separation. Dynamic mechanical measurements show an improvement of the mechanical properties of SBS when i‐PP is the dispersed phase. This reinforcing effect can be observed even at high temperatures when i‐PP is in the rubbery state. The mechanical properties of the blends have been interpreted using Takayanagi's block model. The melting and crystallization behaviour of the i‐PP in the blends has been studied by differential scanning calorimetry. The fractionated crystallization phenomenon has been observed in the blends where i‐PP forms the dispersed phase. The results are consistent with the morphology shown by the blends, in particular, with its phase inversion, which occurs at a composition near to 50% i‐PP. © 2000 Society of Chemical Industry     

Grafting of N‐carbamyl maleamic acid onto a styrene–butadiene–styrene copolymer

A styrene–butadiene–styrene block copolymer (SBS) was functionalized with N‐carbamyl maleamic acid (NCMA) using two peroxide initiators with the aim of grafting polar groups onto the molecular chains of the polymer. The influence of the concentration of benzoyl peroxide (BPO) and 2,5‐dimethyl, 2,5‐diterbuthylperoxihexane (DBPH) was studied. The concentration of peroxy groups ranged between 0.75 and 6 × 10^?4 mol % while the concentration of NCMA was constant at 1 wt %. The reaction temperature was chosen according to the type of peroxide employed, being 140°C for BPO and 190°C for DBPH. FTIR spectra confirmed that NCMA was grafted onto the SBS macromolecules. It was found that the highest grafting level was achieved at a concentration of peroxy groups of about 3 × 10^?4 mol %. Contact angle measurements were used to characterize the surface of the SBS and modified polymers. The contact angle of water drops decreased with the amount of NCMA grafted from 95°, the one corresponding to the SBS, to about 73°. T‐peel strength of polymer/polyurethane adhesive/polymer joints made with the modified polymers was larger than those prepared with the original SBS. The peel strength of SBS modified with 1.5 and 3 × 10^?4 mol % of peroxy groups from BPO were five times larger than that of the original SBS. The materials modified using BPO showed peel strengths higher than the ones obtained with DBPH. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 4468–4477, 2006     

Compatibilization of styrene–butadiene–styrene block copolymer in polypropylene/polystyrene blends by analysis of phase morphology

Effect of compatibilization of styrene–butadiene–styrene (SBS) block copolymer in polypropylene/polystyrene (PP/PS) blends was studied by means of small angle X‐ray scattering (SAXS) and scanning electron microscope (SEM). According to SAXS, a certain amount of SBS was located at the interface in all the analyzed samples, forming the relatively thicker interface layer penetrating into homopolymers, and the thickness of the interface layer was quantified in terms of Porod light scattering theory. The incorporation of SBS into PP/PS blends resulted in a decrease in domain size following an emulsification curve as well as an uniform size distribution, and consequently, a fine dispersion of PP domains in the PS matrix. This effect was more pronounced when the concentration of SBS was higher. A critical concentration of SBS of 15% above which the interface layer approaches to saturation and domain size attains a steady‐state was observed. Further, the morphology fluctuation of unetched fracture surface of umcompatibilized and compatibilized blends was analyzed using an integral constant Q based on Debye‐Bueche light scattering theories. Variation of Q as a function of the concentration of SBS showed that, due to the penetrating interface layer, adhesion between phases was improved, making it possible for applied stress to transfer between phases and leading to more uniform stress distribution when blends were broken; accordingly, a more complicated morphology fluctuation of fracture surface appeared. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103:365–370, 2007     

Thermoreversible gelation of a polystyrene–poly(ethylene/butylene)–polystyrene triblock copolymer in n‐octane/4‐methyl‐2‐pentanone solutions

The thermoreversible gelation of a triblock copolymer polystyrene‐block‐poly(ethylene/butylene)‐block‐polystyrene in n‐octane and two solvent mixtures of n‐octane and 4‐methyl‐2‐pentanone with a high n‐octane content has been studied. n‐Octane and 4‐methyl‐2‐pentanone are selective solvents for the middle poly(ethylene/butylene) block and the end polystyrene blocks, respectively. The influence of the solvent composition on the sol–gel transition and the mechanical properties of the gels was studied. The gel formation temperature increased with the copolymer concentration and the n‐octane content in the solvent system. The mechanical properties of the different gels were studied through oscillatory shear measurements. The concentration dependence of the elastic storage modulus showed an exponent close to that expected for gels in good solvents (2.25) that possess a structure similar to those of chemical networks. © 2002 Society of Chemical Industry     

Grafting of N,N′‐methylenebisacrylamide onto cellulose using Co(III)‐acetylacetonate complex in aqueous medium

The grafting of N,N′‐methylenebisacrylamide (N,N′‐MBA) onto cellulose is carried out using the cobaltacetylacetonate complex (Co(acac)₃) under nitrogen atmosphere at 40°C. The rate of graft copolymerization has been studied as a function of [N,N′‐MBA], [Co(acac)₃], and temperature. The activation energy of grafting is found to be 156.0 k J mol⁻¹ within the temperature range of 30–60°C. The effect of perchloric acid, methanol, and surfactants on graft yield has also been studied and results are suitably explained. The higher efficiency of the metal chelate in initiation of graft copolymerization has been assumed due to the coordination of the π electrons of the N,N′‐MBA with the metal chelate, which facilitated the formation of the radicals through homolytic cleavage of metal–oxygen bond of the cobalt acetylacetonate complex. On the basis of the results, a suitable kinetic scheme for graft copolymerization is presented and rate expression is derived. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 76: 906–912, 2000     

Viscoelastic relaxation of styrene–butadiene–styrene block copolymers with different topological structures

The viscoelastic relaxation of linear styrene–butadiene–styrene triblock copolymer (l‐SBS) and star styrene–butadiene–styrene triblock copolymer (s‐SBS) with four arms were investigated with differential scanning calorimetry and dynamic rheological measurements. Three characteristic viscoelastic responses of l‐SBS and s‐SBS in the plot of the loss tangent (tan δ) and temperature at different frequencies (ω's), which corresponded to the relaxation of the polybutadiene (PB) block (peak I), the glass transition of the polystyrene (PS) phase (peak II), and the mutual diffusion between the PB blocks and PS blocks (peak III), respectively, were observed in the experimental range. Although ω was 0.1 rad/s, a noticeable peak III was gained for both l‐SBS and s‐SBS. The dynamic storage modulus (G′) of l‐SBS showed two distinct types of behavior, depending on the temperature. At temperature (T) < T₂ (where T₂ is the temperature corresponding to peak II), G′ of l‐SBS displayed a very weak ω dependency. In contrast, at T > T₂, G′ decayed much more rapidly. However, G′ of s‐SBS displayed a very weak ω dependency at both T < T₂ and T > T₂. Only near T₂ did s‐SBS decay with ω a little sharply. These indicated, in contrast to l‐SBS, that s‐SBS still exhibited more elasticity even at T > T₂ because of its crosslinking point between the PB blocks (the star structure). In the lower ω range, l‐SBS exhibited a stronger peak III than s‐SBS despite the same styrene content for l‐SBS and s‐SBS. The high tan δ value of peak III for l‐SBS was considered to be related to the internal friction among the PB blocks or the whole l‐SBS chain, not the PS blocks. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Mechanical and piezo‐resistive properties of styrene–butadiene–styrene copolymer covalently modified with graphene/styrene–butadiene–styrene composites

As novel piezoelectric materials, carbon‐reinforced polymer composites exhibit excellent piezoelectric properties and flexibility. In this study, we used a styrene–butadiene–styrene triblock copolymer covalently grafted with graphene (SBS‐g‐RGO) to prepare SBS‐g‐RGO/styrene–butadiene–styrene (SBS) composites to enhance the organic solubility of graphene sheets and its dispersion in composites. Once exfoliated from natural graphite, graphene oxide was chemically modified with 1,6‐hexanediamine to functionalize with amino groups (GO–NH₂), and this was followed by reduction with hydrazine [amine‐functionalized graphene oxide (RGO–NH₂)]. SBS‐g‐RGO was finally obtained by the reaction of RGO–NH₂ and maleic anhydride grafted SBS. After that, X‐ray diffraction, X‐ray photoelectron spectroscopy, Raman spectroscopy, scanning electron microscopy, transmission electron microscopy, thermogravimetric analysis, and other methods were applied to characterize SBS‐g‐RGO. The results indicate that the SBS molecules were grafted onto the graphene sheets by covalent bonds, and SBS‐g‐RGO was dispersed well. In addition, the mechanical and electrical conductivity properties of the SBS‐g‐RGO/SBS composites showed significant improvements because of the excellent interfacial interactions and homogeneous dispersion of SBS‐g‐RGO in SBS. Moreover, the composites exhibited remarkable piezo resistivity under vertical compression and great repeatability after 10 compression cycles; thus, the composites have the potential to be applied in sensor production. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46568.     

Influence of the extrusion process on the morphology and micromechanical behavior of polystyrene‐block‐(polystyrene‐co‐butadiene)‐block‐polystyrene star block copolymer/homopolystyrene blends

The influence of the extrusion process on the morphology and micromechanical behavior of an asymmetric polystyrene‐block‐(polystyrene‐co‐butadiene)‐block‐polystyrene (SBS) star block copolymer and its blends with general‐purpose homopolystyrene (hPS) was studied with films prepared with a single‐screw extruder. The techniques used were transmission electron microscopy and uniaxial tensile testing. Unlike the pure SBS block copolymer possessing a gyroid‐like morphology, whose deformation was found to be insensitive to the processing conditions, the mechanical properties of the blends strongly depended on the extrusion temperature as well as the apparent shear rate. The deformation micromechanism was primarily dictated by the blend morphology. The yielding and cavitation of the nanostructures were the principal deformation mechanism for the blends having a droplet‐like microphase‐separated morphology, whereas cavitation dominated for the blends containing macrophase‐separated layers of polystyrene. The mechanical properties of the blends were further examined with respect to the influence of the temperature and shear rate on the phase behavior of the blends. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2007     

Characterization of end‐functionalized styrene–butadiene–styrene copolymers and their application in modified asphalt

End amino, carboxylic acid, and hydroxyl functionalized styrene–butadiene–styrene (SBS) triblock copolymers were prepared with 1,5‐diazabicyclo[3.1.0]hexane, carbon dioxide, and epoxy ethane as capping agents, respectively. The effects of the end polar groups on the morphology and dynamic mechanical properties were investigated. Transmission electron microscopy images suggested that the group at the end of the polystyrene (PS) segment made the morphology of the PS domains disordered and incompact. Dynamic mechanical results showed that the storage and loss modulus increased after SBS was end‐functionalized. End amino and carboxylic acid groups improved the compatibility and storage stability of SBS‐modified asphalt. However, the effect of the end‐hydroxyl group on the improvement of the storage stability of SBS‐modified asphalt was not obvious. The differential scanning calorimetry analysis of SBS‐modified asphalt further showed that the compatibility and storage stability of SBS‐modified asphalt were improved by the attachment of amino or carboxylic acid groups through the anionic polymerization method. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 8–16, 2007     

Investigation of morphology formation in SBS block copolymer/homopolystyrene blends

Polymer blends comprising a polystyrene‐block‐polybutadiene‐block‐polystyrene (SBS) block copolymer and atactic homopolystyrene (hPS) were investigated using injection molded and solution cast samples. The morphology of the materials was studied by means of transmission electron microscopy (TEM) and scanning force microscopy (SFM). Dynamic mechanical analysis (DMA) was used to characterize the phase behavior and the morphology formation of the block copolymer as well as of the SBS/hPS blends. The glass transition temperatures seem to strongly depend on the homogeneity of the corresponding phases. A distinct difference was found between the morphologies of the blends prepared by different methods. While the SBS block copolymer always shows a lamellar morphology in injection molded or as‐cast samples, the injection molded blends show a disturbance in the morphology consisting of alternating layers. In contrast, in the case of as‐cast samples, added hPS forms polystyrene domains dispersed in a matrix of the pure block copolymer. Regarding the change in the glass transition temperature, in the effective volume and in the interfacial volume obtained from DMA curves, the morphology formation of the injection molded samples (pure SBS block copolymer and the corresponding blends) was investigated. Two different structural models for the blends are proposed. Polym. Eng. Sci. 44:1534–1542, 2004. © 2004 Society of Plastics Engineers.     

Blends of SBS triblock copolymer with poly(2,6‐dimethyl‐1,4‐phenylene oxide)/polystyrene mixture

Blends of styrene–butadiene–styrene (SBS) or styrene–ethylene/1‐butene–styrene (SEBS) triblock copolymers with a commercial mixture of polystyrene (PS) and poly(2,6‐dimethyl‐1,4‐phenylene oxide) (PPO) were prepared in the melt at different temperatures according to the chemical kind of the copolymer. Although solution‐cast SBS/PPO and SBS/PS blends were already known in the literature, a general and systematic study of the miscibility of the PS/PPO blend with a styrene‐based triblock copolymer in the melt was still missing. The thermal and mechanical behavior of SBS/(PPO/PS) blends was investigated by means of DSC and dynamic thermomechanical analysis (DMTA). The results were then compared to analogous SEBS/(PPO/PS) blends, for which the presence of a saturated olefinic block allowed processing at higher temperatures (220°C instead of 180°C). All the blends were further characterized by SEM and TGA to tentatively relate the observed properties with the blends' morphology and degradation temperature. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 2698–2705, 2003     

Morphology and rheological behavior of maltene–polymer blends. I. Effect of partial hydrogenation of poly(styrene‐block‐butadiene‐block‐styrene‐block)‐type copolymers

Because of the importance of the maltene–polymer interaction for the better performance of polymer‐modified asphalts, this article reports the effects of the molecular characteristics of two commercial poly(styrene‐block‐butadiene‐block‐styrene‐block) (SBS) polymers and their partially hydrogenated derivatives [poly{styrene‐block[(butadiene)_1?x–(ethylene‐co‐butylene)_x]‐block‐styrene‐block} (SBEBS)] on the morphology and rheological behavior of maltene–polymer blends (MPBs) with polymer concentrations of 3 and 10% (w/w). Each SBEBS and its parent SBS had the same molecular weight and polystyrene block size, but they differed from each other in the composition of the elastomeric block, which exhibited the semicrystalline characteristics of SBEBS. Maltenes were obtained from Ac‐20 asphalt (Pemex, Salamanca, Mexico), and the blends were prepared by a hot‐mixing procedure. Fluorescence microscopy images indicated that all the blends were heterogeneous, with polymer‐rich and maltene‐rich phases. The rheological behavior of the blends was determined from oscillatory shear flow data. An analysis of the storage modulus, loss modulus, complex modulus, and phase angle as a function of the oscillatory frequency at various temperatures allowed us to conclude that the maltenes behaved as pseudohomogeneous viscoelastic materials that could dissipate stress without presenting structural changes; moreover, all the MPBs were more viscoelastic than the neat maltenes, and this depended on both the characteristics and amount of the polymer. The MPBs prepared with SBEBS were more viscoelastic and possessed higher elasticity than those prepared with SBS. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Nitroxide‐mediated ‘living’ free radical synthesis of novel rod–coil diblock copolymers with polystyrene and mesogen‐jacketed liquid‐crystal polymer segments

The synthesis of rod–coil diblock copolymers with narrow polydispersity was achieved for the first time by TEMPO‐mediated ‘living’ free radical polymerization of styrene and 2,5‐bis[(4‐methoxyphenyl)oxycarbonyl]styrene. The block architecture of the two diblock copolymers thus prepared, MPCS‐block‐St (5400/2400) and MPCS‐block‐St (10 800/8700), was confirmed by GPC, ¹H and ¹³C NMR and DSC studies. The liquid‐crystalline behaviour of the copolymers was studied by DSC and polarized optical microscope. It was observed that both copolymers showed two distinct glass transitions, corresponding to polystyrene and poly(‐2,5‐bis[(4‐methoxyphenyl)oxycarbonyl]styrene). Above the glass transition temperature of rigid block, liquid‐crystalline phase was formed. The clearing point of the phase is higher than the polymer decomposition temperature. © 2000 Society of Chemical Industry     

Controlled synthesis of low‐molecular‐weight polyethylene waxes by titanium–biphenolate–ethylaluminum sesquichloride based catalyst systems

Soluble complexes of titanium(IV) bearing sterically hindered biphenols, such as biphenol, 1,1′‐methylene di‐2‐naphthol, 2,2′‐methylene bis(4‐chlorophenol), 2,2′‐methylene bis(6‐tert‐butyl‐4‐ethyl phenol), and 2,2′ ethylidene bis(4,6‐di‐tert‐butyl phenol), were prepared and characterized. These catalyst precursors, formulated as [Ti(O∧O)X₂], were active in the polymerization of ethylene at high temperatures in combination with ethylaluminum sesquichloride as a cocatalyst. The ultra‐low‐molecular‐weight polyethylenes (PEs) were linear and crystalline and displayed narrow polydispersities. The catalytic polymerization leading to PE waxes in this reaction exhibited unique properties that have potential applications in surface coatings and adhesive formulations. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104: 1531–1539, 2007     

Formation of SBS thermoplastic block copolymer using hexamethyleneimine alkenyl lithium (N‐Li) initiator

Styrene and butadiene block copolymers (SBS) end functionalized with amino group at the initiating chain ends were synthesized using hexamethyleneimine alkenyl lithium (N‐Li) as initiator, tetrahydrofuran (THF) as polar modifier, and cyclohexane as solvent. By attaching a few number of butadiene molecules to N‐lithium hexamethyleneimine, a new N‐Li initiator that can effectively initiate the polymerization of SBS was obtained. ¹H NMR spectrums of the N‐Li initiator terminated by ethanol, end functionalized polystyrene, and SBS block copolymer proved the structure of N‐Li and its ability to initiate the polymerization of styrene and SBS block copolymer. Kinetics studies suggested that the polymerization rate of styrene in the first block reached the maximum when the ratio of THF/Li was increased to 5, while further increase of the ratio of THF/Li could not improve the polymerization rate. The molecular weight distribution (MWD) of SBS initiated by N‐Li varied with the ratio of THF/Li. The vinyl content of polybutadiene block increased by improving the ratio of THF/Li, while the content of cis‐1,4 and trans‐1,4 structures decreased. The vinyl content of end functionalized SBS was somewhat higher than that of SBS initiated by classical n‐butyllithium when other condition was the same. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 81–88, 2006     

PP—SBS共混物光氧化降解的研究

和橡胶类树脂进行共混是聚丙烯(PP)改性的重要途径之一,共混有橡胶组分的PP改性树脂在其力学性能获得改进的同时,其老化性能必然也有一定的变化,我们用红外光谱方法研究了聚丙烯和苯乙烯-丁二烯星型嵌段共聚物的共混物(PP-SBS)的光氧化降解行为。 图1是SBS膜在光氧化过程中红外光谱的变化。当膜在光老化箱(光源为高压汞灯)中经过2.5小时光照后,红外光谱已发生了明显的变化,910cm~(-1)(—C=C端基)和967cm~(-1)     

Styrene–butadiene–styrene/montmorillonite nanocomposites synthesized by anionic polymerization

We successfully synthesized an exfoliated styrene–butadiene–styrene triblock copolymer (SBS)/montmorillonite nanocomposite by anionic polymerization. Gel permeation chromatography showed that the introduction of organophilic montmorillonite (OMMT) resulted in a small high‐molecular‐weight fraction of SBS in the composites, leading to a slight increase in the weight‐average and number‐average molecular weights as well as the polydispersity index. The results from ¹H‐NMR revealed that the introduction of OMMT almost did not affect the microstructure of the copolymer when the OMMT concentration was lower than 4 wt %. Transmission electron microscopy and X‐ray diffraction showed a completely exfoliated nanocomposite, in which both polystyrene and polybutadiene blocks entered the OMMT galleries, leading to the dispersion of OMMT layers on a nanoscale. The exfoliated nanocomposite exhibited higher thermal stability, glass‐transition temperature, elongation at break, and storage modulus than pure SBS. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci, 2006     

Synthesis and characterization of Pst‐b‐PDMS‐b‐PSt copolymers by atom transfer radical polymerization

Polystyrene‐b‐poly(dimethylsiloxane)‐b‐polystyrene (Pst‐b‐PDMS‐b‐PSt) triblock copolymers were synthesized by atom transfer radical polymerization (ATRP). Commercially available difunctional PDMS containing vinylsilyl terminal species was reacted with hydrogen bromide, resulting in the PDMS macroinitiators for the ATRP of styrene (St). The latter procedure was carried out at 130°C in a phenyl ether solution with CuCl and 4, 4′‐di (5‐nonyl)‐2,2′‐bipyridine (dNbpy) as the catalyzing system. By using this technique, triblock copolymers consisting of a PDMS center block and polystyrene terminal blocks were synthesized. The polymerization was controllable; ATRP of St from those macroinitiators showed linear increases in M_n with conversion. The block copolymers were characterized with IR and ¹H‐NMR. The effects of molecular weight of macroinitiators, macroinitiator concentration, catalyst concentration, and temperature on the polymerization were also investigated. Thermodynamic data and activation parameters for the ATRP are reported. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 3764–3770, 2004