Synthesis and characterization of novel optically active poly(imide–urethane)s derived from N,N′‐(pyromellitoyl)‐bis‐(L‐leucine) diisocyanate and aromatic diols

N,N′‐(Pyromellitoyl)‐bis‐(L ‐leucine) diacid was reacted with ethyl chloroformate in the presence of triethylamine followed by reaction with activated sodium azide and gave N,N′‐(pyromellitoyl)‐bis‐(L ‐leucine) diacylazide in high yield. This diacylazide was heated in dry benzene and gave the unstable N,N′‐(pyromellitoyl)‐bis‐(L ‐leucine) diisocyanate ( 5 ) in quantitative yield. Thus, diisocyanate 5 was generated in situ and polycondensation reaction of this monomer with several aromatic diols, such as 4,4′‐dihydroxybiphenyl, 1,4‐hydroquinone, bisphenol A, phenolphthalein and 1,4‐dihydroxyanthraquinone, was performed in dry toluene under refluxing in the presence of 1,4‐diazabicyclo[2.2.2]octane (triethylenediamine) as a catalyst. The polymerization reactions proceeded within 48 h, producing a series of optically active poly(imide–urethane)s with good yield and moderate inherent viscosity in the range 0.18–0.28 dl g^?1. All of the above polymers were fully characterized by infrared spectra, elemental analyses and specific rotation. Some structural characterization and physical properties of these optically active poly(imide–urethane)s are reported Copyright © 2003 Society of Chemical Industry     

Polyurethane foams with the contribution of products of hydroxyalkylation of N,N′‐bis(2‐hydroxyalkyl)oxamides with alkylene carbonates—obtaining and properties

In the reactions of N,N′‐bis(2‐hydroxyethyl)oxamide (BHEOD) with an excess of ethylene carbonate (EC) and N,N′‐bis(2‐hydroxypropyl)oxamide (BHPOD) with an excess of propylene carbonate (PC), the hydroxyethoxy and hydroxypropoxy derivatives of oxamide (OD) were obtained, respectively, distinguished by an increased thermal stability. First time, these derivatives were used as polyol components to obtain foamed polyurethane plastics with the contribution of 4,4′‐diisocyanate diphenylmethane (MDI). The rigid polyurethane foams of a slight water uptake, good stability of dimensions, enhanced thermal stability, and compression strength were obtained. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Microwave‐promoted rapid synthesis of new optically active poly(amide imide)s derived from N,N′‐(pyromellitoyl)‐bis‐L‐isoleucine diacid chloride and aromatic diamines

A pyromellitic dianhydride (benzene‐1,2,4,5‐tetracarboxylic dianhydride) was reacted with L ‐isoleucine in acetic acid, and the resulting imide acid [N,N′‐(pyromellitoyl)‐bis‐L ‐isoleucine] (4) was obtained in a high yield. 4 was converted into N,N′‐(pyromellitoyl)‐bis‐L ‐isoleucine diacid chloride by a reaction with thionyl chloride. The polycondensation reaction of this diacid chloride with several aromatic diamines, including 1,4‐phenylenediamine, 4,4′‐diaminodiphenyl methane, 4,4′‐diaminodiphenylsulfone (4,4′‐sulfonyldianiline), 4,4′‐diaminodiphenylether, 2,4‐diaminotoluene, and 1,3‐phenylenediamine, was developed with two methods. The first method was polymerization under microwave irradiation, and the second method was low‐temperature solution polymerization, with trimethylsilyl chloride used as an activating agent for the diamines. The polymerization reactions proceeded quickly and produced a series of optically active poly(amide imide)s with good yields and moderate inherent viscosities of 0.17–0.25 dL/g. All of the aforementioned polymers were fully characterized by IR, elemental analyses, and specific rotation. Some structural characterization and physical properties of these optically active poly(amide imide)s are reported. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 951–959, 2004     

Forgotten monomers: access to α‐modified N‐vinylpyrrolidone polymers via C‐alkylation

Alkylation of N‐vinylpyrrolidone using lithium diisopropylamide and bis(2‐bromoethyl) ether was carried out to obtain 3‐(2‐(2‐bromoethoxy)ethyl)‐1‐vinyl‐2‐pyrrolidone ( 2 ). The derivative 2 represents a versatile starting molecule for further modification via nucleophilic displacement yielding, for example, the bicyclic 2‐vinyl‐8‐oxa‐2‐azaspiro[4.5]decan‐1‐one ( 4 ) or the ammonium salt 3‐diethoxy‐N,N′‐((dimethylbenzyl)ammonium bromide)‐1‐vinyl‐2‐pyrrolidone ( 10 ). Via free radical polymerization of 4 and 10 , the corresponding homopolymers were obtained. Copolymerization of 4 and 10 with N,N′‐diethylacrylamide yielded water‐soluble materials. The thermosensitive solubility of copolymers poly[(2‐vinyl‐8‐oxa‐2‐azaspiro[4.5]decan‐1‐one)‐co‐(N,N′‐diethylacrylamide)] and poly[(3‐diethoxy‐N,N′‐((dimethylbenzyl)ammonium bromide)‐1‐vinyl‐2‐pyrrolidone)‐co‐(N‐vinylpyrrolidone)] in water was investigated. © 2015 Society of Chemical Industry     

Highly trans‐1,4‐specific polymerization of 1,3‐butadiene catalyzed by [2,6‐bis{(4S)‐ (−)‐isopropyl‐2‐oxazolin‐2‐yl}pyridine] chromium complex activated with modified methylaluminoxane

Chromium complexes with N,N,N‐tridentate ligands, LCrCl₃ (L = 2,6‐bis{(4S)‐(?)‐isopropyl‐2‐oxazolin‐2‐yl}pyridine ( 1 ), 2,2′:6′,2″‐terpyridine ( 2 ), and 4,4′,4″‐tri‐tert‐butyl‐2,2′:6′,2″‐terpyridine ( 3 )), were prepared. The structures of 1 and 2 were determined by X‐ray crystallography. Upon activation with modified methylaluminoxane (MMAO), 1 catalyzed the polymerization of 1,3‐butadiene, while 2 and 3 was inactive. The obtained poly(1,3‐butadiene) obtained with 1 ‐MMAO was found to have completely trans‐1,4 structure. The 1 ‐MMAO system also showed catalytic activity for the polymerization of isoprene to give polyisoprene with trans‐1,4 (68%) and cis‐1,4 (32%) structure. Copyright © 2011 Society of Chemical Industry     

Modification of bismaleimide resin by poly(ethylene phthalate‐co‐ethylene terephthalate), poly(ethylene phthalate‐co‐ethylene 4,4′‐biphenyl dicarboxylate), and poly(ethylene phthalate‐co‐ethylene 2,6‐naphthalene dicarboxylate)

Aromatic polyesters were prepared and used to improve the brittleness of bismaleimide resin, composed of 4,4′‐bismaleimidodiphenyl methane and o,o′‐diallyl bisphenol A (Matrimid 5292 A/B resin). The aromatic polyesters included PEPT [poly(ethylene phthalate‐co‐ethylene terephthalate)], with 50 mol % of terephthalate, PEPB [poly(ethylene phthalate‐co‐ethylene 4,4′‐biphenyl dicarboxylate)], with 50 mol % of 4,4′‐biphenyl dicarboxylate, and PEPN [poly(ethylene phthalate‐co‐ethylene 2,6‐naphthalene dicarboxylate)], with 50 mol % 2,6‐naphthalene dicarboxylate unit. The polyesters were effective modifiers for improving the brittleness of the bismaleimide resin. For example, inclusion of 15 wt % PEPT (MW = 9300) led to a 75% increase in fracture toughness, with retention in flexural properties and a slight loss of the glass‐transition temperature, compared with the mechanical and thermal properties of the unmodified cured bismaleimide resin. Microstructures of the modified resins were examined by scanning electron microscopy and dynamic viscoelastic analysis. The toughening mechanism was assessed as it related to the morphological and dynamic viscoelastic behaviors of the modified bismaleimide resin system. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 81: 2352–2367, 2001     

Synthesis and characterization of new optically active poly(amide‐imide‐urethane) thermoplastic elastomers,derived from 4,4′‐(hexafluoroisopropylidene)‐N,N′‐bis(phthaloyl‐L‐leucine‐p‐aminobenzoic acid) and PEG‐MDI

A new class of optically active poly(amide‐imide‐urethane) was synthesized via two‐step reactions. In the first step, 4,4′‐methylene‐bis(4‐phenylisocyanate) (MDI) reacts with several poly(ethylene glycols) (PEGs) such as PEG‐400, PEG‐600, PEG‐2000, PEG‐4000, and PEG‐6000 to produce the soft segment parts. On the other hand, 4,4′‐(hexafluoroisopropylidene)‐N,N′‐bis(phthaloyl‐L ‐leucine‐p‐amidobenzoic acid) (2) was prepared from the reaction of 4,4′‐(hexafluoroisopropylidene)‐N,N′‐bis(phthaloyl‐L ‐leucine) diacid chloride with p‐aminobenzoic acid to produce hard segment part. The chain extension of the above soft segment with the amide‐imide 2 is the second step to give a homologue series of poly(amide‐imide‐urethanes). The resulting polymers with moderate inherent viscosity of 0.29–1.38 dL/g are optically active and thermally stable. All of the above polymers were fully characterized by IR spectroscopy, elemental analyses, and specific rotation. Some structural characterization and physical properties of this new optically active poly(amide‐imide‐urethanes) are reported. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 2288–2294, 2004     

Synthesis and characterization of novel poly(amide imide)s based on bis(p‐amidobenzoic acid)‐n‐trimellitylimido‐L‐leucine

N‐Trimellitylimido‐L ‐leucine was reacted with thionyl chloride, and N‐trimellitylimido‐L ‐leucine diacid chloride was obtained in a quantitative yield. The reaction of this diacid chloride with p‐aminobenzoic acid was performed in dry tetrahydrofuran, and bis(p‐amidobenzoic acid)‐N‐trimellitylimido‐L ‐leucine (5) was obtained as a novel optically active aromatic imide–amide diacid monomer in a high yield. The direct polycondensation reaction of the monomer imide–amide diacid 5 with 4,4′‐diaminodiphenylsulfone, 4,4′‐diaminodiphenylether, 1,4‐phenylenediamine, 1,3‐phenylenediamine, 2,4‐diaminotoluene, and benzidine (4,4′‐diaminobiphenyl) was carried out in a medium consisting of triphenyl phosphite, N‐methyl‐2‐pyrolidone, pyridine, and calcium chloride. The resulting novel poly(amide imide)s (PAIs), with inherent viscosities of 0.22–0.52 dL g^?1, were obtained in high yields, were optically active, and had moderate thermal stability. All of the compounds were fully characterized with IR spectroscopy, elemental analyses, and specific rotation. Some structural characterization and physical properties of these new optically active PAIs are reported. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 84: 35–43, 2002; DOI 10.1002/app.10181     

Copper‐based reverse ATRP process for the controlled radical polymerization of methyl methacrylate

A series of copper‐based reverse atom transfer radical polymerizations (ATRP) were carried out for methyl methacrylate (MMA) at same conditions (in xylene, at 80°C) using N,N,N′,N′‐teramethylethylendiamine (TMEDA), N,N,N′,N′,N′‐pentamethyldiethylentriamine (PMDETA), 2‐2′‐bipyridine, and 4,4′‐Di(5‐nonyl)‐2,2′‐bipyridine as ligand, respectively. 2,2′‐azobis(isobutyronitrile) (AIBN) was used as initiator. In CuBr₂/bpy system, the polymerization is uncontrolled, because of the poor solubility of CuBr₂/bpy complex in organic phase. But in other three systems, the polymerizations represent controlled. Especially in CuBr₂/dNbpy system, the number‐average molecular weight increases linearly with monomer conversion from 4280 up to 14,700. During the whole polymerization, the polydispersities are quite low (in the range 1.07–1.10). The different results obtained from the four systems are due to the differences of ligands. From the point of molecular structure of ligands, it is very important to analyze deeply the two relations between (1) ligand and complex and (2) complex and polymerization. The different results obtained were discussed based on the steric effect and valence bond theory. The results can help us deep to understand the mechanism of ATRP. The presence of the bromine atoms as end groups of the poly(methyl methacrylate) (PMMA) obtained was determined by ¹H‐NMR spectroscopy. PMMA obtained could be used as macroinitiator to process chain‐extension reaction or block copolymerization reaction via a conventional ATRP process. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Microwave‐assisted polycondensation of 4,4′‐(hexafluoroisopropylidene)‐N,N′‐bis(phthaloyl‐L‐leucine) diacid chloride with aromatic diols

A new facile and rapid polycondensation reaction of 4,4′‐(hexafluoroisopropylidene)‐N,N′‐bis(phthaloyl‐L ‐leucine) diacid chloride (1) with several aromatic diols such as phenol phthalein (2a), bis phenol‐A (2b), 4,4′‐hydroquinone (2c), 1,4‐dihydroxyanthraquinone (2d), 1,8‐dihydroxyanthraquinone (2e), 1,5‐dihydroxy naphthalene (2f), dihydroxy biphenyl (2g), and 2,4‐dihydroxyacetophenone (2h) was performed by using a domestic microwave oven in the presence of a small amount of a polar organic medium such as o‐cresol. The polymerization reactions proceeded rapidly, compared with the conventional solution polycondensation, and was completed within 10 min, producing a series of optically active poly(ester‐imide)s with quantitative yield and high inherent viscosity of 0.50–1.12 dL/g. All of the above polymers were fully characterized by IR, elemental analyses, and specific rotation. Some structural characterization and physical properties of this optically active poly(ester‐imide)s are reported. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 77: 3003–3009, 2000     

Effect of type of substitution in 4,4′‐bis‐(diaminodiphenyl) methane hardener on cure kinetics,mechanical, and flame retardant properties of tetrafunctional epoxy resins

The nature of the substituent in 4,4′‐bis‐(diaminodiphenyl) methane (DDM) hardener on the cure kinetics, mechanical, and flame retardant properties of N,N,N′,N′‐tetraglycidyl diaminodiphenyl methane (TGDDM) resin is investigated in comparison with unsubstituted DDM and widely used 4,4′‐bis‐(diaminodiphenyl) sulfone hardeners. Dynamic differential scanning calorimetry (DSC) and cure rheology studies showed that the substitution decreased the reactivity of the amine. An electron‐withdrawing chlorine substituent was found to be more effective than an electron‐releasing methyl group in reducing the amine reactivity. Substituted and unsubstituted DDM hardeners showed two peaks in their DSC thermograms that were due to steric hindrance in the former and deficiency of amine in the latter. Substitution showed its effect on the mechanical properties and glass‐transition temperature. The flexural modulus was increased; however, the Izod impact and glass‐transition temperature were decreased in substituted amine systems. The limiting oxygen index results showed higher flame retardancy in the chlorine substituted hardener system compared to other hardener systems that were studied. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 480–491, 2006     

Polymeric decontaminant: N,N‐dichloro poly(styrene‐co‐divinyl benzene) sulfonamide—synthesis,characterization and efficacy against simulant of sulfur mustard

N,N‐Dichloro poly(styrene‐co‐divinylbenzene) sulfonamide (1) reacts with 2‐chloro ethyl phenyl sulfide (2), a simulant of sulfur mustard (SM), at room temperature, yielding corresponding nontoxic sulfones and sulfoxides in aqueous as well as aprotic medium. The decontamination reaction was monitored by gas chromatography, and products were identified by gas chromatography–mass spectrometry. N,N‐dichloro poly(styrene‐co‐divinylbenzene) sulfonamide was synthesized by three steps from a commercial starting material sulfonate cation‐exchange resin and characterized by FTIR, and TGA, and compressive strength by universal testing machine. The positive chlorine content of this polymer was checked by standard iodometry titration. The synthesized positive chlorine compound is observed to be a promising against a simulant of SM, chiefly in the situation where use of aqueous medium is precluded. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

N,N′‐Pentamethylenethiuram disulfide‐ and N,N′‐pentamethylenethiuram hexasulfide‐accelerated sulfur vulcanization. I. Interaction of curatives in the absence of rubber

N,N′‐pentamethylenethiuram disulfide (CPTD), CPTD/sulfur, and N,N′‐pentamethylenethiuram hexasulfide (CPTP6) were heated in a DSC at a programmed heating rate and isothermally at 140°C. Residual reactants and reaction products were analyzed by HPLC at various temperatures or reaction times. CPTD rapidly formed N,N′‐pentamethylenethiuram monosulfide (CPTM) and N,N′‐pentamethylenethiuram polysulfides (CPTP) of different sulfur rank, CPTP of higher sulfur rank forming sequentially, as reported earlier for tetramethylthiuram disulfide (TMTD). As with TMTD, the high concentration of the accelerator monosulfide that develops is attributed to an exchange between CPTD and sulfenyl radicals, produced on homolysis of CPTD. However, a different mechanism for CPTP formation to that suggested for TMTD is proposed. It is suggested that disulfenyl radicals, resulting from CPTM formation, exchange with CPTD and/or CPTP already formed, to give CPTP of higher sulfur rank. CPTD/sulfur and CPTP6 very rapidly form a similar product spectrum with CPTP of sulfur rank 1–14 being detectable. Unlike with TMTD/sulfur, polysulfides of high sulfur rank did not form sequentially when sulfur was present, CPTP of all sulfur rank being detected after 30 s. It is proposed that sulfur adds directly to thiuram sulfenyl radicals. Recombination with sulfenyl radicals, which would be the most plentiful in the system, would result in highly sulfurated unstable CPTP. CPTP of higher sulfur rank are less stable than are disulfides as persulfenyl radicals are stabilized by cyclization, and the rapid random dissociation of the highly sulfurated CPTP, followed by the rapid random recombination of the radicals, would result in the observed product spectrum. CPTP is thermally less stable than is TMTD and at 140°C decomposed rapidly to N,N′‐pentamethylenethiourea (CPTU), sulfur, and CS₂. At 120°C, little degradation was observed. The zinc complex, zinc bis(pentamethylenedithiocarbamate), did not form at vulcanization temperatures, although limited formation was observed above 170°C. ZnO inhibits degradation of CPTD to CPTU. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 77: 2718–2731, 2000     

Tertiary‐amine‐free,non‐planar,sulfone‐containing,tetrafunctional epoxy and its application as a high temperature matrix

Non‐amine‐derived tetrafunctional epoxies have several advantages over the amine‐derived N,N,N′,N′‐tetraglycidyl‐4,4′‐diaminodiphenyl methane (TGDDM) in high temperature applications. Although two non‐amine‐derived tetrafunctional epoxies were developed in our laboratory, further improvements in toughness using less loading amount is still desirable. Thus, a tertiary‐amine‐free, non‐planar and triphenylmethane‐containing tetrafunctional epoxy (STFE) with a sulfone spacer was synthesized. When it was mixed with diglycidyl ether of bisphenol A (DGEBA) and cured with 4,4′‐diaminodiphenylsulfone (DDS), both thermal and mechanical performances outperformed TGDDM. Moreover, STFE modified system shows the highest toughness (35.7 kJ m^–2) among three amine‐free and triphenylmethane‐containing epoxies at merely 5 wt% loading. Molecular simulation and thermomechanical analysis results suggest that the improved mechanical properties could be related to the geometry of the molecule and larger free volume. Despite a marginal drop in T_g, the thermal degradation temperature is better than that of TGDDM/DDS. In addition, the moisture resistance of STFE/DGEBA/DDS is much better than that of TGDDM/DDS. Thus, STFE modified DGEBA could be a potential replacement for TGDDM in some high temperature applications. © 2020 Society of Chemical Industry     

Synthesis of novel optically active poly(ester‐imide)s with benzophenone linkages by microwave‐assisted polycondensation

A new simple and rapid polycondensation reaction of 4,4′‐carbonyl‐bis(phthaloyl‐L ‐alanine)diacid chloride [N,N ′‐(4,4′‐carbonyldiphthaloyl)]bisalanine diacid chloride with several diphenols, such as bisphenol‐A, phenolphthalein, 1,8‐dihydroxyanthraquinone, 4,4′‐dihydroxybiphenyl, 1,5‐dihydroxynaphthalene and hydroquinone, in the presence of a small amount of a polar organic medium such as o‐cresol was performed using a domestic microwave oven. The polycondensation reaction proceeded rapidly and was almost complete within 12 min to give a series of poly(ester‐imide)s with inherent viscosities of about 0.35–0.58 dl g⁻¹. The resulting poly(ester‐imide)s were obtained in high yield and are optically active and thermally stable. All the above compounds have been fully characterized by IR spectroscopy, elemental analysis, inherent viscosity (η_inh), solubility test and specific rotation. Thermal properties of the poly(ester‐imide)s have been investigated using thermal gravimetric analysis (TGA). © 2000 Society of Chemical Industry     

Synthesis and properties of poly(amide–imide)s based on N,N′‐bis(4‐carboxyphenyl)‐4,4′‐oxydiphthalimide,p‐aminobenzoic acid and various aromatic diamines

A new diimide–diacid monomer, N,N′‐bis(4‐carboxyphenyl)‐4,4′‐oxydiphthalimide (I), was prepared by azeotropic condensation of 4,4′‐oxydiphthalic anhydride (ODPA) and p‐aminobenzoic acid (p‐ABA) at a 1:2 molar ratio in a polar solvent mixed with toluene. A series of poly(amide–imide)s (PAI, III_a–m) was synthesized from the diimide–diacid I (or I′, diacid chloride of I) and various aromatic diamines by direct polycondensation (or low temperature polycondensation) using triphenyl phosphite and pyridine as condensing agents. It was found that only III_k–m having a meta‐structure at two terminals of the diamine could afford good quality, creasable films by solution‐casting; other PAIs III using diamine with para‐linkage at terminals were insoluble and crystalline; though III_g–i contained the soluble group of the diamine moieties, their solvent‐cast films were brittle. In order to improve their to solubility and film quality, copoly(amide–imide)s (Co‐PAIs) based on I and mixtures of p‐ABA and aromatic diamines were synthesized. When on equimolar of p‐ABA (m = 1) was mixed, most of Co‐PAIs IV had improved solubility and high inherent viscosities in the range 0.9–1.5 dl g^?1; however, their films were still brittle. With m = 3, series V was obtained, and all members exhibited high toughness. The solubility, film‐forming ability, crystallinity, and thermal properties of the resultant poly(amide–imide)s were investigated. © 2002 Society of Chemical Industry     

Cure kinetics of multifunctional epoxies with 2,2′‐dichloro‐4,4′‐diaminodiphenylmethane as hardener

The curing behavior of the epoxy resin N,N,N′,N′‐tetraglycidyldiaminodiphenyl methane (TGDDM) with triglycidyl p‐aminophenol as a reactive diluent was investigated using 2,2′‐dichloro‐4,4′‐diaminodiphenylmethane (DCDDM) as the curing agent. The effect of the curing agent on the kinetics of curing, shelf‐life, and thermal stability in comparison with a TGDDM‐diaminodiphenylsulfone (DDS) system was studied. The results showed a lesser activation energy at the lower level of conversion with a broader cure exotherm for the epoxy‐DCDDM system in comparison with the epoxy‐DDS system, although the overall activation energy for the two systems was comparable. TGA studies showed more stability in the epoxy‐DCDDM system than in the epoxy‐DDS system. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 77: 2097–2103, 2000     

Lower critical solution temperatures of thermo‐responsive poly(N‐isopropylacrylamide) copolymers with racemate or single enantiomer groups

BACKGROUND: Thermo‐responsive copolymers with racemate or single enantiomer groups are attracting increasing attention due to their fascinating functional properties and potential applications. However, there is a lack of systematic information about the lower critical solution temperature (LCST) of poly(N‐isopropylacrylamide)‐based thermo‐responsive chiral recognition systems. In this study, a series of thermo‐responsive chiral recognition copolymers, poly[(N‐isopropylacrylamide)‐co‐(N‐(S)‐sec‐butylacrylamide)] (PN‐S‐B) and poly[(N‐isopropylacrylamide)‐co‐(N‐(R,S)‐sec‐butylacrylamide)] (PN‐R,S‐B), with different molar compositions, were prepared. The effects of heating and cooling processes, optical activity and amount of chiral recognition groups in the copolymers on the LCSTs of the prepared copolymers were systematically studied. RESULTS: LCST hysteresis phenomena are found in the phase transition processes of PN‐S‐B and PN‐R,S‐B copolymers in a heating and cooling cycle. The LCSTs of PN‐S‐B and PN‐R,S‐B during the heating process are higher than those during the cooling process. With similar molar ratios of N‐isopropylacrylamide groups in the copolymers, the LCST of the copolymer containing a single enantiomer (PN‐S‐B) is lower than that of the copolymer containing racemate (PN‐R,S‐B) due to the steric structural difference. The LCSTs of PN‐R,S‐B copolymers are in inverse proportion to the molar contents of the hydrophobic R,S‐B moieties in these copolymers. CONCLUSION: The results provide valuable guidance for designing and fabricating thermo‐responsive chiral recognition systems with desired LCSTs. Copyright © 2008 Society of Chemical Industry     

Synthesis and characterization of soluble poly(amide‐imide)s bearing triethylamine sulfonate groups as gas dehumidification membrane material

A series of soluble poly(amide‐imide)s (PAIs) bearing triethylammonium sulfonate groups were synthesized directly using trimellitic anhydride chloride (TMAC) polycondensation with sulfonated diamine such as 2,2′‐benzidinedisulfonic acid (BDSA), 4,4′‐diaminodiphenyl ether‐2,2′‐disulfonic acid (ODADS), and nonsulfonated diamine 4,4‐diaminodiphenyl methane in the presence of triethylamine. The resulting copolymers exhibited high molecular weights (high inherent viscosity), and a combination of desirable properties such as good solubility in dipolar aprotic solvents, film‐forming capability, and good mechanical properties. Wide‐angle X‐ray diffraction revealed that the polymers were amorphous. These copolymers showed high permeability coefficients of water vapor because of the presence of the hydrophilic triethylammonium sulfonate groups. The water vapor permeability coefficients (P_w) and permselectivity coefficients of water vapor to nitrogen and methane [α(H₂O/N₂) and α(H₂O/CH₄)] of the films increased with increasing the amount of the triethylammonium sulfonated groups. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Microwave assisted novel synthetic route for polyfluorenes containing triphenylamine and solubilizing alkyl moiety for blue emitting diodes

A series of blue electroluminescent polyfluorenes (PFs) containing triphenylamine and various alkyl moieties were synthesized using an Ni(0) mediated C?C Yamamoto coupling reaction assisted by microwaves. The synthesized PFs were characterized by various spectroscopic techniques. Their absorption and photoluminescence properties were investigated in solvent and found to possess characteristic electronic absorption and emission spectra. These PFs were found to emit in the blue region (407?415 nm) with high quantum yield in the range 0.41?0.73. Cyclic voltammetry studies of the PFs revealed that the compounds were stable under redox conditions with highest occupied molecular orbital (HOMO) and lowest unoccupied molecular orbital in the range 5.24–5.29 eV and 1.98?2.01 eV, respectively. The E_HOMO for the PFs was similar to the most widely used hole transporting materials N,N′‐Di(1‐naphthyl)‐N,N′‐diphenyl‐(1,1′‐biphenyl)‐4,4′‐diamine (NPD), N,N′‐Bis(3‐methylphenyl)‐N,N′‐diphenylbenzidine (TPD) and N²,N²,N²′,N²′,N⁷,N⁷,N⁷′,N⁷′‐octakis(4‐methoxyphenyl)‐9,9′‐spirobi[9H‐ fluorene]‐2,2′,7,7′‐tetramine, Spiro‐OMeTAD (spiro‐OMe‐TAD). The thermal stability observed for the PFs accounts for their use under ambient conditions. The electrochemical studies of the fabricated polymer light emitting diodes suggest that the PFs have potential to be used as hole transporting and blue electroluminescent materials for optoelectronic devices. © 2017 Society of Chemical Industry