三相多室气升式环流反应器气含率的研究

在1个4流道的三相多室气升式环流反应器中,以空气-水-K树脂为体系,采用压差法测量气含率,考察了上升室气体表观速率、固体装载量对上升室与下降室气含率的影响.结果表明:上升室的气含率随着该室气体表观速率增加而增加,而随着另一上升室气体表观速率增加而略有降低;下降室的气含率随着该室气体表观速率增加呈现3种变化趋势,而随着另...     

Simulation and experimentation on the gas holdup characteristics of a novel oscillating airlift loop reactor

BACKGROUND: The classical airlift loop reactor (ALR) has been widely used in petrochemical, biochemical, energy and environmental processes due to such advantages as simple structure, without motional mechanism, easy sealing and low energy consumption. A novel ALR has been designed using forced periodic reversible ventilation, termed an airlift reversible loop reactor (ARLR). RESULTS: Using computational fluid dynamics (CFD) simulation and experimental validation, the mass transfer characteristics of the ARLR were studied. The simulation results predicted the experimental data well, especially at low ventilation capacity. The oscillation period had significant effects on gas holdup and the mass transfer coefficient of the ARLR. When ventilation capacity was increased from 0.22 to 3.49 vvm, compared with central airlift and annular airlift reactors, ARLR increased the mass transfer coefficient by 9–31% and 10–58%, respectively, according to simulation results, and by 11–25% and 14–58%, respectively, according to experimental data. CONCLUSION: The results showed that the ARLR could significantly enhance gas holdup and mass transfer coefficient compared with traditional central airlift and annular airlift reactors. Results indicated that the optimum oscillation period decreased with increase of ventilation capacity. ARLR has the potential for application in aerobic fermentation. © 2012 Society of Chemical Industry     

多室环流反应器气含率的三维数值模拟与分析

在常温常压条件下,以空气为气相、水为液相,对多室气升式环流反应器内气液两相流动状态进行了数值模拟,采用Euler两相流模型模拟了不同表观气速条件下各室气含率的分布情况。数值模拟计算结果表明,上升室气含率随表观气速的增大近似呈线性增长;各上升室气含率受自身表观气速的影响较大,而受另外一上升室表观气速的影响较小。     

两级气液内环流反应器内气含率和循环液速

基于多釜串联可以有效减小返混的原理,通过引入特殊设计的级间构件构建了一种新型的两级内环流反应器。实验研究了级间构件形式、表观气速、表观液速和气液分离器对每一级内气含率和循环液速的影响。实验结果表明,表观气速对反应器二级(上一级)中上升管与下降管气含率之差和循环液速影响较大,而对一级(下一级)的影响较小;各级内上升管和下降管的气含率均随表观液速的增大而减小,但影响程度较小。基于推动力和阻力平衡建立了预测反应器中每一级的气含率和循环液速的流体力学模型,模型预测值与实验结果吻合较好。     

旋流气升式环流反应器的局部气、固含率研究

新开发的有机玻璃制成的旋流气升式环流反应器高为2m、内径75mm,内部的导流筒(材料为PVC)高1.5m、内径30mm、壁厚1mm且装有10组扇形翅片。以空气-水为两相物系、空气-水-K树脂为三相物系,常温常压下,利用直接取样法和压差法测量了上升区局部的气含率、固含率,研究了不同底部间隙、不同固体装填体积分数下表观气速和轴向高度对上升区气含率、固含率的影响规律。结果表明:在均匀鼓泡流时上升区气含率随着表观气速的增大而增大,随着固体装载量的增加而下降;在非均匀鼓泡流时,三相物系的气含率高于两相物系的气含率。随着上升区轴向高度的增大,上升区局部气含率变化不大;底部间隙越大,气含率越小。在轴向高度较低时上升区固含率随着轴向高度的增大而减小,轴向高度较高时上升区固含率基本保持不变。     

气升式内环流反应器内局部气含率径向分布

The local gas holdup profiles in an internal-loop airlift reactor were studied experimentally by using dual electrical conductivity probe under different conditions,including superficial velocity,surface tension and liquid viscosity.The results showed that the radial gas holdup profile has a parabolic shape,which was consistent with the empirical model of Luo.Local gas holdup distribution parameters were obviously influenced by flow regime and almost remained unchanged in the same flow regime.In the gas distributor region,the profiles were steeper in the homogenous flow regime than in the heterogeneous flow regime.However,in the stable region,there was an inverse change trend in two flow regimes.The increase of surface tension,superficial velocity and liquid viscosity made the profile of local gas holdup steeper in two flow regimes.     

气固环流反应器的研究进展

气固环流反应器是将气液环流理论与稠密气固流态化理论进行合理移植、耦合而形成的一种新型气固流化床反应器。对近年来国内外学者在该领域的研究进行了回顾,参考了内循环流化床的一些研究结果,对操作条件、几何结构对气固环流反应器内两相流体力学行为的影响规律进行了总结和分析,并对进一步的研究进行了展望。     

强制液体外循环气升式内环流反应器的流体力学特性

在有机玻璃制成的主体反应器(φ0.286 m×3.0 m)内,采用空气-水的气液两相体系考察了不同表观气速下带有中心下料管和环管式气体分布器的环流反应器内局部气含率和内环气泡上升速度的流体力学特性。结果表明：气含率均随表观气速的增大而增大;从外环流入内环的气泡数量比较少;在相同条件下外环的气含率远远低于内环的气含率;新型气体分布器的采用和液体外循环的引入可以增大床层气含率并使其分布趋于均匀,从而增大了内环中气液两相的接触面积和湍动强度,使传递过程得到强化。在此基础上采用商业软件ANSYS CFX10.0对该反应器进行了数值模拟研究,模拟结果与实验数据基本吻合,说明了基于实验验证的Euler-Euler法可以用于该反应器开发和放大研究。     

高长径比三相内环流反应器中相含率的分布研究

在长径比为22的三相内环流反应器中,常温常压下,以空气-水-石英砂为物系,根据无因次准数建立了气含率、固含率的预测模型,考察了在不同粒径下上升区气含率、下降区气含率和上升区固含率、下降区固含率随表观气速的变化规律和不同固体体积分数下轴向固含率的分布情况。结果表明：不同粒径下上升区和下降区气含率均随表观气速的增大而增大;当粒径（ds）≤0．3mm时,上升区固含率随表观气速的增加呈平缓趋势,下降区固含率随表观气速的增加而增加,当0．3mm〈d。≤1．2mm时,上升区固含率随表观气速的增加而呈先下降后增加的趋势,下降区固含率随表观气速的增加而下降;不同固体体积分数下的固体颗粒的固含率随着轴向高度的增大而变化平缓,能够均匀的分布在反应器中;气含率和固含率的计算值和实验值吻合较好,其平均相对误差分别为6．32％、4．56％。     

高长径比三相内环流反应器中细颗粒相含率和循环液速的分布研究

在高径比为22的三相内环流反应器中,在常温常压下以空气-水-石英砂为物系,研究了在不同粒径下上升区固含率、下降区固含率和上升区循环液速随表观气速的变化规律和不同粒径下轴向固含率的分布情况,以及在固体体积分数不同的条件下,平均气含率和上升区气含率随表观气速的变化情况。结果表明:当粒径(ds)≤0.3 mm时,上升区固含率随表观气速的增加呈平缓变化趋势,下降区固含率随表观气速的增加而增加;当0.3 mm相似文献   

Hydrodynamics of a novel multi-stage external loop airlift reactor

In the present investigation a novel multi-stage external loop airlift reactor with hydro-dynamically induced continuous bubble generation, breakup and regeneration has been proposed. The system has been designed to operate with relatively large sized bubbles, so that interfacial circulation can be induced in the liquid-bubble interfaces and faster transfer of components can take place by turbulent diffusion through the interface of the bubbles and also due to the physical rupture and reformation of the bubbles. The system was also designed to operate in three stages operating in series so that in each stage completely deaerated liquid could be brought in contact with freshly generated bubbles. Detailed studies on the gas holdup and liquid circulation velocity have been carried out with respect to various values of superficial gas as well as liquid velocities. The gas holdup of the proposed multi-stage system is 45% higher than the single stage system, which results in better mass transfer characteristics. Empirical correlations describing the performance of the proposed reactor have been presented in this paper.     

底部间隙对多室环流反应器流动特性的影响

在空气-水-石英砂三相多室气升式环流反应器(MALR)中,调节底部转角连接处间隙高度分别为18,28,38mm,在表观气速1.2～4.2cm/s范围内,实验研究了底部阻力系数、相含率、循环液速随反应器底部间隙的变化规律。结果表明,随着底部间隙的增大,底部转角处的局部阻力系数减小,循环液速增大,流体夹带进入下降室的气泡和固体颗粒均增多,下降室的气含率和固含率均增大。     

气升式发酵罐生产核酸酶P_1发酵过程的动力学

利用15L外循环气升式反应器,初步研究了桔青霉分批式液体深层发酵生产核酸酶P1的发酵动力学过程。Logistic模型可以较好地反映菌体的生长动力学规律,Luedeking-Piret则比较好地描述了发酵过程中的核酸酶P1的活力与菌体生长的关系,并利用此模型可以判断桔青霉发酵生产核酸酶P1的过程中,核酸酶P1的产出与菌体的生长是属于部分耦联的,其发酵过程属于部分耦联型发酵。     

气升式外环流反应器流体力学参数的轴径向分布

在气升式外环流反应器（Φ 0.09 m×1.8 m）内,利用压差法和双探针电导探头技术考察了不同表观气速下空气-水两相体系中气含率及气泡参数随轴径向位置的变化规律,测得了平均及局部气含率、气泡尺寸及分布、气泡上升速度、气泡频率以及气液相界面积,并从气液流场特征及气泡间相互作用等方面对实验结果作出分析。基于实验数据拟合出局部气含率随表观气速和轴径向位置的关联式。     

固体颗粒对三相气升式环流反应器流动特性的影响

将液相视为连续相,气相和固相视为分散相,同时考虑各相之间的相互作用,结合气液固三相流体的动力学理论,建立气液固三相环流反应器三流体湍流流动的Eulerian模型.采用计算模拟软件Fluent对三相环流反应器的流动状况进行模拟,考察表观气速、固含率、颗粒大小对反应器的气含率以及液体流动速度的影响.模拟结果较好地解释了气升式环流反应器内的三相流体行为,模型与实验结果较好地吻合,表明了模型的可行性.     

Circulation liquid velocity,gas holdup and volumetric oxygen transfer coefficient in external-loop airlift reactors

The effects of the horizontal connection length (0.1 ± L_e ± 0.5 m), the cross-sectional area ratio of downcomer-to-riser (0.11 ± A_d/A_r± 0.53), and the superficial gas velocity on gas phase holdups in the riser and downcomer were studied. The circulation liquid velocity, the mixing performance and the volumetric mass transfer coefficient in the external-loop airlift reactors were also measured. The horizontal connection length and A_d/A_r were major parameters which strongly affected the performance of external-loop airlift reactors. Useful correlations in the external-loop airlift reactors were obtained for gas holdups, the volumetric mass transfer coefficient, the circulation liquid velocity, and the mixing time.     

Gas holdup,bubble size distribution,and mass transfer in an airlift reactor with ceramic membrane and perforated plate distributor

The airlift reactor is one of the most commonly used gas–liquid two-phase reactors in chemical and biological processes. The objective of this study is to generate different-sized bubbles in an internal loop airlift reactor and characterize the behaviours of the bubbly flows. The bubble size, gas holdup, liquid circulation velocity, and the volumetric mass transfer coefficient of gas–liquid two-phase co-current flow in an internal loop airlift reactor equipped with a ceramic membrane module (CMM) and a perforated-plate distributor (PPD) are measured. Experimental results show that CMM can generate small bubbles with Sauter mean diameter d₃₂ less than 2.5 mm. As the liquid inlet velocity increases, the bubble size decreases and the gas holdup increases. In contrast, PPD can generate large bubbles with 4 mm < d₃₂ < 10 mm. The bubble size and liquid circulation velocity increase as the superficial gas velocity increases. Multiscale bubbles with 0.5 mm < d₃₂ < 10 mm can be generated by the CMM and PPD together. The volumetric mass transfer coefficient k_La of the multiscale bubbles is 0.033–0.062 s⁻¹, while that of small bubbles is 0.011–0.057 s⁻¹. Under the same flow rate of oxygen, the k_La of the multiscale bubbles increases by up to 160% in comparison to that of the small bubbles. Finally, empirical correlations for k_La are obtained.     

CFD在气升式环流反应器结构优化上的应用

利用CFD软件ANSYS 14.0及欧拉-欧拉多相流模型,模拟不同高径比、环隙比下气升式环流反应器的气液两相流动,得到反应器内循环液速和气含率等参数的详细分布。对比模拟结果表明,高径比为7,环隙比1时,反应器具有最优流化状态。CFD在气升式环流反应器的结构优化具有明显的指导意义。