酸性介质中氮杂环类缓蚀剂在碳钢上的吸附行为

合成了一种新型含氮杂环有机物:2-(4-叔丁基-苯甲基硫)-5-(1,2,4-三氮唑)-甲基-(1,3,4-噁二唑)(TBTO),通过交流阻抗、动电位极化、失重实验研究了其在酸性介质中的缓蚀效率,并用扫描电镜方法分析了碳钢表面的腐蚀形貌变化.结果表明:TBTO在0.5mol/L H2SO4中对Q235钢的缓蚀作用高达96.2%,能同时抑制碳钢腐蚀的阴、阳极反应过程;化合物在碳钢表面上的吸附行为服从Langmuir吸附等温式.同时用量子化学中的从头算方法对缓蚀剂的分子结构与缓蚀性能的关系进行了研究.     

新型杂环化合物在1 mol/L HCl中对Q235钢的缓蚀性能研究

通过失重、电化学测试以及量子化学计算方法研究了新型杂环恶二唑化合物5-［(1H - 1,2,4 - 三氮唑 – 1- 基)甲基］-1,3,4 噁二唑 - 2 - 硫醇(TAOT)在1 mol/L HC1中对Q235钢（碳钢）的缓蚀作用.结果表明,TAOT在1 mol/L HC1中对Q235钢的缓蚀作用高达89.1％,能同时抑制碳钢腐蚀的阴、阳极反应过程.碳钢的阻抗值随TAOT浓度增加而增大,其在碳钢表面的吸附符合Langmuir等温式,量子化学计算结果也表明,该化合物物可能是通过巯基提供电子与碳钢表面相互作用来起到缓蚀作用的.     

橙子皮提取物在H3PO4溶液中的缓蚀性能及缓蚀机理研究

目的 推进绿色植物提取物类缓蚀剂的快速发展,选用橙子皮提取物(NOPE)作为磷酸环境中Q235钢的缓蚀剂。方法 通过简单的乙醇、丙酮回流法提取获得NOPE。通过红外光谱(FTIR)和紫外光谱(UV)验证NOPE的主要结构及主要成分在磷酸中的稳定性。采用失重法、动态电位极化法(PDP)、线性极化(LPR)和电化学阻抗谱法(EIS)研究NOPE在0.5 mol/L的H3PO4溶液中对Q235钢的缓蚀性能。通过计算研究温度对热力学参数(Ea、 、 )和吸附性能参数( 、 、 )的影响。结果NOPE明显减缓了0.5 mol/L H3PO4介质中Q235钢的腐蚀速率,属于以抑制阳极金属溶解为主的混合型缓蚀剂。随着NOPE浓度的增大,阳极电流密度减小和活性腐蚀部位被阻断,腐蚀速率降低,缓蚀效率增大。在温度为303 K、NOPE质量浓度为3.0 g/L条件下,对Q235钢缓蚀效率都在90%以上。此外,NOPE的有效成分在Q235钢表面的吸附符合Langmuir等温式,且以物理吸附为主。通过扫描电镜(SEM)、能谱分析(EDS)和接触角的测量证明了NOPE在钢表面的缓蚀作用的存在,降低了Q235钢的酸腐蚀速率。量子化学研究证实,NOPE对碳钢较好的缓蚀和吸附性能是由于橙皮苷和黄酮的官能团。结论 在0.5 mol/L的H3PO4溶液体系中,NOPE对Q235钢具有较好的缓蚀性能,是一种在酸洗领域中有着较好应用前景的绿色缓蚀剂,可以为植物提取类的缓蚀剂的发展提供一定的指导。     

IAA 在硫酸溶液中对碳钢的缓蚀性能研究

目的研究吲哚-3-乙酸(IAA)在H2SO4(0.1 mol/L)溶液中对碳钢(Q235)的缓蚀性能,降低碳钢生产过程对环境的影响。方法采用动电位极化曲线测试、交流阻抗实验、失重实验和扫描电镜实验分析缓蚀剂的缓蚀性能及作用机理。结果 IAA的缓蚀效率随着缓蚀剂浓度的增加而逐渐增大,当IAA浓度增加到4×10-3mol/L时,缓蚀效率最高达到88.85%。温度升高,缓蚀效率降低,说明IAA不宜于高温下使用。IAA是一种混合型缓蚀剂,对阴极反应和阳极反应均有抑制作用,且在缓蚀剂分子吸附过程中,吸附在碳钢表面的水分子和缓蚀剂分子发生竞争吸附作用,能有效阻止H+的穿越,从而抑制腐蚀H+的放电。IAA在碳钢表面的吸附遵循Langmuir吸附等温模型,该吸附自发进行且是物理吸附和化学吸附共同作用。缓蚀剂通过抑制腐蚀反应的活性点,提高活化能垒,防止碳钢溶解腐蚀。IAA在碳钢表面形成保护膜,减轻了腐蚀。结论 IAA是一种以抑制阳极反应为主的混合型缓蚀剂,在0.1 mol/L H2SO4溶液中能够对Q235碳钢起到优异的保护作用。     

苯胺四聚体聚乙二醇嵌段共聚物在盐酸介质中对Q235钢的缓蚀性能

目的研究苯胺四聚体PEG两亲性嵌段共聚物(PEG-TA)对Q235钢在1 mol/L HCl介质中的缓蚀性能。方法采用静态失重测试、电化学测试、腐蚀表面形貌分析研究了自制的PEG-TA在1 mol/L HCl介质中对Q235钢的缓蚀性能,并探讨了其在Q235钢表面的吸附行为。结果红外和紫外表征表明,氨基封端苯胺四聚体和聚乙二醇为原料成功合成了两亲性嵌段共聚物PEG-TA。极化曲线研究表明,PEG-TA的加入明显可以抑制Q235钢在1 mol/L HCl介质中的腐蚀,且随着PEG-TA浓度的增加,缓蚀效果越好,在25℃的实验温度范围内,质量浓度为30 mg/L时,PEG-TA的缓蚀效率可以达到93.97%,属于阴极抑制为主的混合型缓蚀剂。电化学阻抗图谱研究表明,随着PEG-TA浓度的增加,Q235钢表面腐蚀反应的电荷转移电阻和膜电阻逐渐增大,钢表面缓蚀剂的含量和覆盖率增加,腐蚀抑制性增强。PEG-TA缓蚀剂分子在Q235钢表面的吸附遵循Langmuir等温模型,并且属于物理和化学混合吸附。SEM研究证明,在1 mol/L HCl中,PEG-TA可有效地抑制碳钢的腐蚀。结论 PEG-TA在1 mol/L HCl中有效提高了Q235钢的耐蚀性,是一种高效环保的缓蚀剂。     

Q235钢表面纳米化的电化学腐蚀行为

采用表面机械研磨技术(SMAT)使Q235钢实现了表面纳米化,随后分析及比较了Q235钢经不同弹丸直径处理后在0.05 mol/L H2SO4+0.05 mol/L Na2SO4介质中的腐蚀行为。结果表明,除了Q235钢用10 mm弹丸直径处理的SMAT试样腐蚀电流密度变大,耐腐蚀性能下降之外,用其他弹丸直径处理的SMAT试样耐腐蚀性能均有所提高。     

三唑化合物在0.5 mol/L硫酸中对Q235钢的缓蚀作用

合成了一种新型三氮唑化合物:1-苯次乙亚氨基-2-巯基-5-[1-(1,3,4-三氮唑)亚甲基]-1,3,4-三氮唑(PMT),并通过失重试验、动电位极化、电化学阻抗谱及扫描电镜方法研究了其在0.5mol/L硫酸溶液中对Q235碳钢的缓蚀作用。结果表明,该三唑化合物在硫酸中对Q235碳钢有较好的缓蚀效果,是混合型缓蚀剂。     

L-苯丙氨酸对Q235钢在硫酸中的缓蚀作用

采用电化学方法,研究了L-苯丙氨酸对Q235钢在0.5mol/L H2SO4溶液中的缓蚀作用及缓蚀机理,分析了其缓蚀剂类型。结果表明:L-苯丙氨酸的缓蚀效率随浓度的增加而增大,而且随着温度的升高,Q235钢表面单个活性位点上吸附的缓蚀剂分子数量增加,缓蚀效率也增大;L-苯丙氨酸属于混合抑制型缓蚀剂,作用机理为几何覆盖效应,其在Q235钢表面的吸附为单分子吸附,且吸附规律符合El-Awady动力学模型。     

食用香料1,4-二硫-2,5-二醇环保型缓蚀剂对X70钢在0.5mol/L H2SO4溶液中的缓蚀性能研究

使用实验和理论计算方法研究了食用香料 1,4-二硫-2,5-二醇(DDD)对X70管线钢在0.5 mol/L硫酸溶液中的缓蚀性能.结果表明,DDD能够有效的抑制X70钢在H2SO4介质中的腐蚀,在温度为298 K时,DDD的缓蚀效率可以达到93.6％;随着温度的升高,DDD依然能够展现出良好的缓蚀性能.腐蚀微观形貌观察...     

改性咪唑啉缓蚀剂抗H2S/CO2腐蚀性能研究

本文在合成1-(2-氨乙基)-2-十五烷基咪唑啉(A)的基础上,利用硫代氨基脲对其进行改性,制备了一种1-(2-氨基-硫脲乙基)-2-十五烷基咪唑啉(B)新型缓蚀剂。通过失重法和电化学方法研究了A、B两种缓蚀剂在H2S、CO2共存条件下对Q235钢的缓蚀性能,探讨了其在Q235钢表面的吸附行为。结果显示,改性后的缓蚀剂B具有更优的抗H2S、CO2腐蚀的缓蚀性能,最高缓蚀效率在92%以上。两者在Q235钢表面均是单分子层吸附,属于以化学吸附为主的混合吸附。最后采用量子化学方法对两种缓蚀剂的缓蚀机理进行了分析。     

Effects of Post-weld Heat Treatment on Microstructure,Mechanical Properties and the Role of Weld Reinforcement in 2219 Aluminum Alloy TIG-Welded Joints

In as-welded state, each region of 2219 aluminum alloy TIG-welded joint shows diff erent microstructure and microhardness due to the diff erent welding heat cycles and the resulting evolution of second phases. After the post-weld heat treatment, both the amount and the size of the eutectic structure or θ phases decreased. Correspondingly, both the Cu content in α-Al matrix and the microhardness increased to a similar level in each region of the joint, and the tensile strength of the entire joint was greatly improved. Post-weld heat treatment played the role of solid solution strengthening and aging strengthening. After the post-weld heat treatment, the weld performance became similar to other regions, but weld reinforcements lost their reinforcing eff ect on the weld and their existence was more of an adverse eff ect. The joint without weld reinforcements after the post-weld heat treatment had the optimal tensile properties, and the specimens randomly crack in the weld zone.     

The First Phase of the SRIF Industrialized Base in ＂West Area＂ Has Been Put into Operation

After nearly two years＇ tense construction, the first phase of industrialized base of Shenyang Research Institute of Foundry （SRIF）, located at the Tiexi Casting and Forging Industrial Park in the west of Tiexi District, has now been completed and formally put into operation.     

Thermodynamics Study on the Decomposition of Chromite with KOH

Institute of Process Engineering, Chinese Academy of Sciences, China, has proposed a method for oxidative leaching of chromite with potassium hydroxide. Understanding the mechanism of chromite decomposition, especially in the potassium hydroxide fusion, is important for the optimization of the operating parameters of the oxidative leaching process. A traditional thermodynamic method is proposed and the thermal decomposition and the reaction decomposition during the oxidative leaching of chromite with KOH and oxygen is discussed, which suggests that chromite is mainly destroyed by reactions with KOH and oxygen. Meanwhile, equilibrium of the main reactions of the above process was calculated at different temperatures and oxygen partial pressures. The stable zones of productions, namely, K2CrO4 and Fe2O3, increase with the decrease of temperature, which indicates that higher temperature is not beneficial to thermodynamic reactions. In addition, a comparison of the general alkali methods is carried out, and it is concluded that the KOH leaching process is thermodynamically superior to the conventional chromate production process.     

Influence of Heat Treatment on Damping Behaviour of the Magnesium Wrought Alloy AZ61

The effect of isochronal heat treatments for 1h on variation of damping, hardness and microstructural change of the magnesium wrought alloy AZ61 was investigated. Damping and hardness behaviour could be attributed to the evolution of precipitation process. The influence of precipitation on damping behaviour was explained in the framework of the dislocation string model of Granato and Lücke.     

Effect of Rare Earth Doping on Impedance,Modulus and Conductivity Properties of Multiferroic Composites:0.5(BiLa_xFe_(1-x)O_3)–0.5(PbTiO_3)

The Lanthanum-doped bismuth ferrite–lead titanate compositions of 0.5(Bi LaxFe1-xO3)–0.5(Pb Ti O3)(x = 0.05,0.10,0.15,0.20)(BLxF1-x-PT) were prepared by mixed oxide method.Structural characterization was performed by X-ray diffraction and shows a tetragonal structure at room temperature.The lattice parameter c/a ratio decreases with increasing of La(x = 0.05–0.20) concentration of the composites.The effect of charge carrier/ion hopping mechanism,conductivity,relaxation process and impedance parameters was studied using an impedance analyzer in a wide frequency range(102–106Hz) at different temperatures.The nature of Nyquist plot confirms the presence of bulk effects only,and non-Debye type of relaxation processes occurs in the composites.The electrical modulus exhibits an important role of the hopping mechanism in the electrical transport process of the materials.The ac conductivity and dc conductivity of the materials were studied,and the activation energy found to be 0.81,0.77,0.76 and 0.74 e V for all compositions of x = 0.05–0.20 at different temperatures(200–300 °C).     

Quantitative Analysis of the Crystallographic Orientation Relationship Between the Martensite and Austenite in Quenching–Partitioning–Tempering Steels

The orientation relationships(ORs)between the martensite and the retained austenite in low-and medium-carbon steels after quenching–partitioning–tempering process were studied in this work.The ORs in the studied steels are identified by selected-area electron diffraction(SAED)as either K–S or N–W ORs.Meanwhile,the ORs were also studied based on numerical fitting of electron backscatter diffraction data method suggested by Miyamoto.The simulated K–S and N–W ORs in the low-index directions generally do not well coincide with the experimental pole figure,which may be attributed to both the orientation spread from the ideal variant orientations and high symmetry of the low-index directions.However,the simulated results coincide well with experimental pole figures in the high-index directions{123}_(bcc).A modified method with simplicity based on Miyamoto’s work was proposed.The results indicate that the ORs determined by modified method are similar to those determined by Miyamoto’method,that is,the OR is near K–S OR for the low-carbon Q–P–T steel,and with the increase of carbon content,the OR is closer to N–W OR in medium-carbon Q–P–T steel.     

Growth Kinetics of Single Inclusion Particle in Molten Melts

On the basis of the single-particle framework, a new theory on inclusion growth in metallurgical melts is developed to study the kinetics of inclusion growth on account of reaction and collision. The studies show that the early growth of inclusion depends on reaction growth and Brawnian motion collision, and where the former is decisive, the late growth depends on turbulence collision and Stokes＇ collision, and where the former is dominant; collision growth is very quick during the smelting process, lessened in the refining process, but nearly negligible in the continuous casting process.     

Theoretical Analysis for the Motion and Temperature of Melt Droplets in Spray Degassing Process

The motion of melt droplets in spray degassing process was analyzed theoretically. The height of the treatment tank in spray degassing process could be determined by the results of theoretical calculation of motion of melt droplets. To know whether the melt droplets would solidify during spraying process, the balance temperature of melt droplets was also theoretically analyzed. Then proof experiments for theoretical results about temperature of melt droplets were carried. In comparison, the experimental results were nearly similar to the calculation results.     

Using Finite Element and Contour Method to Evaluate Residual Stress in Thick Ti-6Al-4V Alloy Welded by Electron Beam Welding

This work was to reveal the residual stress profile in electron beam welded Ti-6Al-4V alloy plates(50 mm thick) by using finite element and contour measurement methods.A three-dimensional finite element model of 50-mmthick titanium component was proposed,in which a column–cone combined heat source model was used to simulate the temperature field and a thermo-elastic–plastic model to analyze residual stress in a weld joint based on ABAQUS software.Considering the uncertainty of welding simulation,the computation was calibrated by experimental data of contour measurement method.Both test and simulated results show that residual stresses on the surface and inside the weld zone are significantly different and present a narrow and large gradient feature in the weld joint.The peak tensile stress exceeds the yield strength of base materials inside weld,which are distinctly different from residual stress of the thin Ti-6Al-4V alloy plates presented in references before.     

Microstructures and Tensile Properties of Ultrafine-Grained Ni–(1–3.5) wt% SiC_(NP) Composites Prepared by a Powder Metallurgy Route

Silicon carbide nanoparticle-reinforced nickel-based composites(Ni–Si CNP),with a Si CNPcontent ranged from1 to 3.5 wt%,were prepared using mechanical alloying and spark plasma sintering.In addition,unreinforced pure nickel samples were also prepared for comparative purposes.To characterize the microstructural properties of both the unreinforced pure nickel and the Ni–Si CNPcomposites transmission electron microscopy(TEM) was used,while their mechanical behavior was investigated using the Vickers pyramid method for hardness measurements and a universal tensile testing machine for tensile tests.TEM results showed an array of dislocation lines decorated in the sintered pure nickel sample,whereas,for the Ni–Si CNPcomposites,the presence of nano-dispersed Si CNPand twinning crystals was observed.These homogeneously distributed Si CNPwere found located either within the matrix,between twins or on grain boundaries.For the Ni–Si CNPcomposites,coerced coarsening of the Si CNPassembly occurred with increasing Si CNPcontent.Furthermore,the grain sizes of the Ni–Si CNPcomposites were much finer than that of the unreinforced pure nickel,which was considered to be due to the composite ball milling process.In all cases,the Ni–Si CNPcomposites showed higher strengths and hardness values than the unreinforced pure nickel,likely due to a combination of dispersion strengthening(Orowan effects) and particle strengthening(Hall–Petch effects).For the Ni–Si CNPcomposites,the strength increased initially and then decreased as a function of Si CNPcontent,whereas their elongation percentages decreased linearly.Compared to all materials tested,the Ni–Si CNPcomposite containing 1.5% Si C was found more superior considering both their strength and plastic properties.