共查询到16条相似文献,搜索用时 156 毫秒
1.
准光模式变换器是实现高功率回旋管高效输出的重要部件。该文针对140 GHz, TE28,8模回旋振荡管研制,开展以Denisov型辐射器和3个准光镜面构成的准光模式变换器设计与实验研究。利用标量衍射法优化辐射器辐射口径处的场分布,其与理想高斯场之间的矢量相关性为96.2%;基于几何光学和高斯波束匹配方法设计了聚焦镜面与波束整形镜面,采用3维全波分析软件Surf3D获得各个镜面上及输出窗处的场分布,对所设计的镜面系统进行了仿真验证,在输出窗处获得了高斯模式含量为96.67%的输出波束,整个模式变换器的功率转换效率为93.98%。以自行研制的TE28,8模激励器作为准光模式变换器的输入,通过对模式变换器转换性能仿真结果验证,在严格控制加工精度及装配和实验过程的基础上,完成了准光模式变换器转换性能的冷测实验。实验结果表明,设计和实验具有合理的一致性,可以作为准光模式变换器工程应用设计和验证手段。 相似文献
2.
为满足聚变用170 GHz回旋管高功率输出和高效率传输的要求,需将高阶工作模式TE25,10转换为高斯波束;针对这一技术需求,完成了170 GHz、TE25,10模式高效准光模式变换器的设计,准光模式变换器由辐射器和镜面系统组成。基于几何光学和耦合波理论,完成了Denisov型辐射器相关设计;基于矢量衍射定理和相位校正算法,设计了由一个抛物面镜面、一个准椭圆镜面及一个相位校正镜面组成的镜面系统;使用Surf3D软件对辐射器进行了优化和计算,使用三维全波仿真软件FEKO对镜面系统进行了优化和计算,主要对辐射器微扰幅值、位置分布及相位差进行了优化。所设计准光模式变换器系统的能量转换效率约为95.2%,波束在输出窗处的标量高斯含量约为97.6%,矢量高斯含量约为91.8%,达到了回旋管的应用要求。 相似文献
3.
针对170 GHz回旋管研究,设计了一种高效Denisov准光模式变换器,该回旋管工作在 模式。模式变换器由微扰结构的辐射器和镜面系统组成。基于耦合模理论和矢量绕射理论,研究了两级微扰辐射器,优化设计了镜面系统。仿真结果显示, 模式转换为高斯光束,其输出功率转换效率为93.7%。 相似文献
4.
准光辐射器是高功率回旋管准光模式变换器的重要组成部分.采用几何光学理论分析圆波导准光辐射器,根据高斯波束(TEM00模)在辐射器切口处形成的原因,利用耦合波理论设计波纹波导准光辐射器.通过编写程序并进行数值优化完成140 GHz、TE28,8模式回旋管波纹波导准光辐射器的设计,结果表明波纹波导辐射器的总长度仅为205.2 mm,切口长度为47.2 mm,在辐射器螺旋切口Brillouin区内高斯模式标量相关系数大于98%.本文所用的方法也可用于其它频率和模式的回旋管准光辐射器设计. 相似文献
5.
对回旋管内置准光模式变换器进行了理论研究和数值模拟。基于几何光学理论和矢量绕射理论,编制了模拟电磁场行为的分析和优化程序,采用Vlasov辐射器和准光反射器实现了线极化准高斯模HE11。结果表明:在一级反射镜下的转换效率为88.3%,增加反射镜级数会降低转换效率。 相似文献
6.
准光辐射器是高功率回旋管准光模式变换器的重要组成部分.本文首先采用几何光学理论分析圆波导准光辐射器,然后根据高斯波束(TEM00模)在辐射器切口处形成的原因,采用耦合波理论设计波纹波导准光辐射器.通过编写程序并进行数值优化完成140GHz,TE28,8模式回旋管波纹波导准光辐射器的设计,结果表明波纹波导辐射器的总长度仅为205.2mm,切口长度为47.2mm,在辐射器螺旋切口Brillouin区内高斯模式标量相关系数大于98%.本文所用的方法也可用于其它频率和模式的回旋管准光辐射器设计. 相似文献
7.
本文设计了一种用于W 波段边廊模回旋振荡管的三反射镜准光模式变换器。该模式变换器由一个Vlasov 型螺旋
切口辐射器和三面聚焦反射镜构成,可以将回旋管输出的高阶模式高效地转换为准高斯模式。根据矢量绕射理论和物理
光学法编写了模拟仿真程序,并对辐射器和反射镜的空间辐射场进行了计算、优化和分析。计算结果表明:输出波束中
高斯基模的标量相关系数为97.9%,矢量相关系数为95.9%,转换效率达到了81.5%。 相似文献
8.
准光模式变换器是大功率输出回旋管的关键部件.采用高转换效率的准光模式变换器可以横向输出电磁波,增大收集极的尺寸,提高回旋管的输出功率,提高整管效率.该文设计的回旋管内置准光模式变换器由Denisov辐射器天线和四个反射镜组成,输入频率为94GHz,模式为TE6,2模.采用耦合波理论分析和优化了Denisov辐射器内的场分布,并根据矢量绕射理论编制数值模拟程序计算了各个反射镜上的场分布,其输出功率转换效率达97.2%.利用三维全波仿真软件feko6.0进行对比分析,最后加工所设计的结构并内置于回旋振荡管进行热测实验,结果表明其输出场分布与理论计算结果基本一致. 相似文献
9.
成功实现高转换效率的140 GHz TE22,6准光模式变换器原型设计。基于周期微扰原理设计Denisov辐射器,实现低边缘绕射的初级出射波束。针对三镜面光路系统,采用全矢物理光学积分作为主要计算手段,围绕主极化场分量进行三级相位修正面迭代优化,实现高出射高斯纯度的模式场转换,其中一级镜的修正有效改善了辐射器出射的不理想性。基于全矢数值仿真确认,相比原二次曲面原型设计,相位修正后的变换器系统的出射高斯纯度从92.7%提高到99.6%,结合98.8%以上的功率传递效率,实现了性能优越的高阶回旋管准光模式变换器原型设计。 相似文献
10.
准光模式转换器是高功率毫米波回旋管的重要组成部份,能够实现电磁波与电子注的分离、隔离波的反射,并实现回旋管的高斯波束输出。基于耦合波理论,分析设计出用于频率140 GHz、TE22.6模式回旋管的Denisov辐射器;基于几何光学理论,设计出准光反射镜面系统,并采用Feko软件进行优化。计算结果表明,所设计的准光模式转换器系统的转换效率约为97.3%,波束的高斯含量约为93.3%,达到了回旋管的应用需求。 相似文献
11.
Michael P. Perkins Rong Cao Jeffrey M. Neilson Ronald J. Vernon 《Journal of Infrared, Millimeter and Terahertz Waves》2007,28(3):207-218
A four-mirror internal quasi-optical mode converter designed for a CPI gyrotron is discussed. Many improved methods were used in designing the mode converter. The launcher was designed and analyzed using the TOL and Surf3d codes developed by CCR. Mirrors 1 and 2 were designed using analytic surfaces to shape the general wavefront curvature of the beam radiated from the launcher. Mirrors 3 and 4 were iteratively designed using improved techniques that produced smooth mirror surfaces. Good agreement was found between theory and low-power cold-test measurements. The fraction of power coupled between the target Gaussian beam and the output of mirror 4, inferred from measurements, was 0.990. The stray radiation from the internal quasi-optical mode converter, inferred from measurements, was only 1.9% of the total power radiated from the launcher. This resulted in a high overall system efficiency of 97.0%, which is greater than previous designs. 相似文献
12.
Thumm M. Yang X. Arnold A. Dammertz G. Michel G. Pretterebner J. Wagner D. 《Electron Devices, IEEE Transactions on》2005,52(5):818-824
A highly efficient quasi-optical mode converter system with several novel features has been designed and tested at Forschungszentrum Karlsruhe (FZK). The converter consists of a dimpled-wall waveguide launcher, one quasi-elliptical mirror and two toroidal mirrors. The coupled-mode theory has been used to analyze the operation of the prebunching waveguide launcher; the radiated fields from the cut of the launcher have been calculated by the scalar diffraction integral. Simulation results show that the advanced dimpled-wall launcher generates a well-focused Gaussian radiation pattern with low diffraction losses. In this case, toroidal mirrors are sufficient to obtain a desired output beam pattern. An efficiency of more than 98% has been achieved to convert the rotating TE/sub 28,8/ cavity mode at 140 GHz into a fundamental Gaussian beam. Experimental measurements show close agreement with theoretical predictions. 相似文献
13.
An improved design for quasi-optical mode conversion of whispering gallery mode gyrotron radiation 总被引:1,自引:0,他引:1
A. W. Möbius J. A. Casey K. E. Kreischer A. Li R. J. Temkin 《Journal of Infrared, Millimeter and Terahertz Waves》1992,13(8):1033-1063
Results are reported of a theoretical and experimental investigation of a quasi-optical mode converter for the transformation of whispering gallery mode gyrotron output into a linearly polarized Gaussian like beam. The mode converter consists of a helically cut waveguide launcher, similar to that originally proposed by Vlasovet al, followed by a focusing mirror. Theoretical results using aperture field methods indicate that the length of the waveguide launcher is of critical importance in providing a confined radiation pattern. Experimental results on the radiation pattern were obtained for several launcher lengths using a 0.6 MW, 149 GHz pulsed gyrotron operating in the TE16,2 mode. Radiation pattern results for the optimum launcher length agree well with theoretical calculations using the Stratton-Chu aperture radiation theory for unperturbed waveguide modes. A mirror focusing in the azimuthal direction was designed by a geometrical optics approach to focus the radiation coming from the launcher. Good focusing with 91.4% efficiency (power in the focused beam divided by gyrotron power) was found experimentally using the combined launcher and mirror with the pulsed gyrotron. These results indicate that quasi-optical antennas are useful for transforming high order, high frequency gyrotron modes into directed beams in free space. 相似文献
14.
采用几何光学模型研究并设计了一个由Vlasov矩形开口辐射器和两级曲面反射器组成的太赫兹回旋管准光模式变换器。利用几何光学理论对Vlasov型准光模式变换器进行了初步设计,采用矢量绕射理论对准光模式变换器进行了详细的分析并编写相应程序,最后结合具体设计参数,得到工作模式在模式变换器中的变换过程。模拟结果表明,太赫兹回旋管中的TE0.6模式在输出窗处被转换为能量集中的准Gauss波束,其效率为89.0%。 相似文献
15.
X. Yang O. Drumm A. Arnold E. Borie G. Dammertz K. Koppenburg B. Piosczyk D. Wagner M. Thumm 《Journal of Infrared, Millimeter and Terahertz Waves》2003,24(10):1599-1608
The quasi-optical mode converter for a frequency step-tunable gyrotron which consists of a dimpled-wall antenna (Denisov-type launcher) and a beam-forming mirror system has been optimized for 9 modes from TE17,6 at 105 GHz to TE23,8 at 143 GHz. The first mirror is a large quasi-elliptical focusing one; the second and third are phase-correcting mirrors with a non-quadratic shape of the surface. The results of calculations show that for these modes the Denisov-type launcher has a well-focused beam with low diffraction losses, and the radiation pattern presents an almost identical field shape for all modes considered. A multi-mode optimization of the phase-correcting mirrors with two different methods has been tested. The simulations show that the phase-correcting mirrors can be used for broadband operation in the frequency range from 105 GHz up to 143 GHz in the various design modes. This quasi-optical mode converter can achieve efficiencies of 94%-98% for converting the rotating high-order cylindrical cavity modes into the usable fundamental Gaussian mode. 相似文献
16.
A quasi-optical mode converter with a bifocal mirror 总被引:1,自引:0,他引:1
This paper presents the design procedure of a quasi-optical mode converter to transform any kind of TEmn mode into a Gaussian wave beam and experimental results obtained in the particular case of the TE64 mode at 110 GHz. The quasi-optical system consists of a helical-cut launcher and a bifocal mirror, which is designed, using the techniques of geometric optics, to focus the radiation of the launcher into a Gaussian focal spot. Such a system was fabricated and tested for the transformation of the TE64 mode. The experimental results showed that about 80% of the power incident in the focal plane is focused into a small Gaussian-like spot of less than 20 mm diameter, while 97% of the power is contained into the main TE64 lobe 相似文献