Time- and temperature-dependent migration studies of Irganox 1076 from plastics into foods and food simulants

The study provides an exhaustive set of migration data for octadecyl 3-(3,5-di-tert-butyl-4-hydroxyphenyl)propionate (Irganox 1076) from low-density polyethylene (LDPE) in several food matrices. Irganox 1076 was used as a model migrant because it represents one of the typical substances used as an antioxidant in food packaging polymers. Kinetic (time-dependent) migration studies of Irganox 1076 were performed for selected foodstuffs chosen with different physical-chemical properties and in relation to the actual European food consumption market. The effect of fat content and of the temperature of storage on the migration from plastic packaging was evaluated. The results show that migration increased with fat content and storage temperature. All data obtained from real foods were also compared with data obtained from simulants tested in the same conditions. In all studied cases, the kinetics in simulants were higher than those in foodstuffs. The work provides data valuable for the extension of the validation of migration model developed on simulants to foodstuffs themselves.     

Time‐ and temperature‐dependent migration studies of Irganox 1076 from plastics into foods and food simulants

The study provides an exhaustive set of migration data for octadecyl 3‐(3,5‐di‐tert‐butyl‐4‐hydroxyphenyl)propionate (Irganox 1076) from low‐density polyethylene (LDPE) in several food matrices. Irganox 1076 was used as a model migrant because it represents one of the typical substances used as an antioxidant in food packaging polymers. Kinetic (time‐dependent) migration studies of Irganox 1076 were performed for selected foodstuffs chosen with different physical–chemical properties and in relation to the actual European food consumption market. The effect of fat content and of the temperature of storage on the migration from plastic packaging was evaluated. The results show that migration increased with fat content and storage temperature. All data obtained from real foods were also compared with data obtained from simulants tested in the same conditions. In all studied cases, the kinetics in simulants were higher than those in foodstuffs. The work provides data valuable for the extension of the validation of migration model developed on simulants to foodstuffs themselves.     

Migration of melamine from can coatings cross-linked with melamine-based resins,into food simulants and foods

Resins based on melamine-formaldehyde and related analogues such as methylolated melamine are used to cross-link coatings used inside food cans and on the metal closures of glass jars. Thirteen commercially coated cans and closures representing 80% of the European market were tested using simulants under realistic industrial heat-processing conditions for canned and jarred foods. The food simulants and the retort conditions used were 3% acetic acid for 1?h at 100°C and 10% ethanol for 1?h at 130°C. The highest migration level seen for melamine into simulant was 332?µg?kg^?1. There was no detectable migration of the melamine analogues cyanuric acid (<1?µg?kg^?1) or ammelide (<5?µg?kg^?1) from any sample. Twelve of the thirteen samples released no detectable ammeline (<5?µg?kg^?1) but the coating giving the highest release of melamine did also release ammeline at 8?µg?kg^?1 with the higher of the two process temperatures used. Migration experiments into food simulant and foods themselves were then conducted using two experimental coatings made using amino-based cross-linking resins. Coated metal panels were exposed to the food simulant 10% (v/v) aqueous ethanol and to three foodstuffs under a range of time and temperature conditions both in the laboratory and in a commercial food canning facility using proprietary time and temperature conditions. The highest migration into a food was 152?µg?kg^?1 from the first coating processed for a long time at a moderate sterilisation temperature. The highest migration into simulant was also from this coating at 220?µg?kg^?1 when processed at 134°C for 60?min, dropping to 190?µg?kg^?1 when processed at 123°C for 70?min. Migration from the second coating was quite uniformly two to three times lower under all tests. These migration results were significantly higher than the levels of melamine extractable using 95% ethanol at room temperature. The experiments show that commercial canning and retorting can be mimicked in an acceptable way using laboratory tests with an autoclave or a simple pressure cooker. The results overall show there is hydrolytic degradation of the melamine cross-linked resins to release additional melamine. There is a strong influence of the temperature of heat treatment applied with foods or simulants but only a minor influence of time of heating and only a minor influence, if any, of food/simulant acidity.     

Investigation into the migration potential of coating materials from cookware products

Twenty-six non-stick-coated cookware samples were purchased, covering a variety of products, coating/metal types and food contact applications. The polymer coatings were identified to be polyethersulphone, polytetrafluoroethylene (PTFE), bisphenol A/epichlorohydrin and one coating for which no good match was obtained with infra-red library spectra. All of the products intended for stove-top use had a polymer coating containing PTFE. The coatings were analysed as purchased and after heating at 250°C for 30 min to simulate actual conditions of use. Total solvent extractables were measured and the overall migration was determined into simulants. None of the products exceeded an overall migration limit of 10 mg dm^-2. Coating materials were analysed by headspace gas chromatography-mass spectrometry (GC-MS), by liquid extraction followed by GC-MS and by liquid extraction followed by liquid chromatography-mass spectroscopy with a particle-beam interface. Benzene was detected in two samples, at 1.4 and 2.4 µg dm^-2. These levels in the coatings are too low to give any detectable migration into foods. There was no detectable release of perfluorochemicals. Several other substances were identified and the worst-case migration was calculated. The origin of many of the substances detected was considered to be by pick-up from the printed packaging materials in which the cookware was sold. Potential consumer exposure was calculated. None of the substances identified had the potential to exceed their tolerable daily intake (TDI) value. To confirm these worst-case calculations, the migration of certain phthalates and of bisphenol A was measured into food simulants. Migration levels were very low.     

Evaluating the migration of ingredients from active packaging and development of dedicated methods: a study of two iron-based oxygen absorbers

The behaviour of two commercial oxygen-scavenging products with respect to migration of active ingredients into foodstuffs was investigated. Migrants were identified, and by using appropriate analytical methods, migration was determined in a variety of liquid, solid or gelled food simulants and foods. Simulants were chosen to cover a range of water activities and viscosities. Foods and the gelled food simulant agar were packed with and without vacuum, and with the oxygen scavenger in various locations relative to the packed food. The main migrants, as identified by X-ray fluorescence spectrometry, infrared spectroscopy and scanning electron microscopy with energy-dispersive spectrometry were Na + and Cl - in non-acidic aqueous simulants, and Na + , Cl - and Fe 2+ in 3% acetic acid. Migration into aqueous simulants exceeded the current European Union limit for total migration from plastic materials (assumed to be currently applicable to these systems) and was probably excessive by any reasonable standard. However, neither oxygen scavenger appeared to release significant quantities of migrants into solid foods when the scavenger was properly located in the package and the packing process does not favour the contents becoming wet by water released from the food.     

纳米塑料复合食品包装中的纳米成分及其迁移研究进展

在塑料食品包装中加入纳米材料可以实现很好的机械性、气体阻隔性或抗菌性等优良性能。然而在与食品 接触的过程中这些纳米材料也有可能迁移到食品中,从而对消费者的健康产生威胁,甚至对市场及消费者信心造成 负面影响。对纳米材料进行迁移研究是对其进行风险评估的重要一环,已经得到国内外学者的广泛关注。本文综述 了纳米塑料复合包装的种类、在食品包装中应用较多的纳米材料及其作用,并详细分析了食品包装中纳米材料向食 品或食品模拟物迁移的研究。结果表明：食品包装中纳米材料向食品或食品模拟释放的量较小,但到目前为止,关 于它们是否会以纳米形态释放出来仍然没有达成统一意见。另外,微波处理、塑料助剂的添加可以影响纳米材料的 释放。     

发泡餐盒中苯乙烯单体和低聚物的测定及迁移风险评估

目的建立聚苯乙烯发泡餐盒中苯乙烯单体和低聚物的检测方法,并对其向食品的迁移进行风险评估。方法采用二氯甲烷溶解-甲醇沉淀法提取餐盒中的苯乙烯单体和低聚物,采用气相色谱-质谱联用法测定目标物向水、酒精和脂肪食品模拟物的迁移量,通过比较各物质的估计日摄入量和毒理学安全阈值评估迁移风险。结果苯乙烯单体和低聚物在0.02~1.00 μg/mL范围内线性良好（R均大于0.99）,在餐盒及食品模拟物中的加标回收率为80.5%~101.2%,相对标准偏差为1.6%~10.5%;在5%显著性水平下各物质向脂肪食品模拟物的迁移量明显大于向水和酒精食品模拟物的迁移量 ,扩散系数为1.3×10-15~1.4×10-9 cm2/s,迁移活化能为33.5~53.3 kJ/mol;目标分析物的估计日摄入量均未超过毒理学关注阈值。结论该方法简单、可靠, 可用于测定发泡餐盒中苯乙烯单体和低聚物的含量。聚苯乙烯发泡餐盒不适合在高温条件下盛放脂肪食品。     

Migration of trimellitic acid from epoxy anhydride can coatings into foods

The migration of trimellitic acid and its esters from epoxy anhydride coatings was determined in simulants as well as in canned foods. The most appropriate simulant was a combination of EC simulants B and C: 2% acetic acid/10% ethanol in water. The average migration into food was 900 μg kg^-1. This far exceeds the 50 μg kg^-1 for which the safety of trimellitic acid and its anhydride is ensured and the Swiss legal limit (QM(T) of 5 mg kg^-1 coating). Furthermore, much trimellitic acid migrated as (unidentified) esters, i.e. toxicological testing of free trimellitic acid is inadequate for the material that in reality migrates.     

食品和药品接触材料聚丙烯中添加剂及 物质迁移的液相色谱分析

聚丙烯(PP)塑料被广泛用在食品及药品的包装上,PP中有害物质的迁移现已成为食品及药品安全隐患的重要组成部分,当食品与包装材料直接接触时,残留在PP包装材料里的抗氧剂及分解产物可以迁移到食品中污染食品。由于食品的多样性,因此常用几种食品模拟液来代替食品在实验室各种控制条件下进行迁移试验,因为迁移到模拟液里的添加剂浓度非常小,其浓度的测定常使用灵敏度较高的高效液相色谱法。迁移受到很多因素的影响,比如:接触的时间温度、接触的方式、包装材料的类型、迁移物的性质等。本文综述了聚丙烯包装材料有害物质迁移的研究现状,为我国食品包装行业标准化体系的建立提供一定的理论依据。     

Comparison of the migration of melamine from melamine–formaldehyde plastics (‘melaware’) into various food simulants and foods themselves

A variety of melaware articles were tested for the migration of melamine into the food simulant 3% w/v acetic acid as a benchmark, and into other food simulants, beverages and foods for comparison. The results indicate that the acidity of the food simulant plays a role in promoting migration, but not by as much as might have been anticipated, since 3% acetic acid gave migration values about double those obtained using water under the same time and temperature test conditions. In contrast, migration into the fatty food simulant olive oil was not detectable and at least 20-fold lower than with the aqueous food simulants. This was expected given the solubility properties of melamine and the characteristics of the melaware plastic. Migration levels into hot acidic beverages (apple juice, tomato juice, red-fruit tea and black coffee) were rather similar to the acetic acid simulant when the same time and temperature test conditions are used, e.g. 2?h at 70°C. However, migration levels into foods that were placed hot into melaware articles and then allowed to cool on standing were much lower (6–14 times lower) than if pre-heated food was placed into the articles and then maintained (artificially) at that high temperature in the same way that a controlled time–temperature test using simulants would be conducted. This very strong influence of time and especially temperature was manifest in the effects seen of microwave heating of food or beverage in the melaware articles. Here, despite the short duration of hot contact, migration levels were similar to simulants used for longer periods, e.g. 70°C for 2?h. This is rationalized in terms of the peak temperature achieved on microwave heating, which may exceed 70°C, counterbalancing the shorter time period held hot. There was also evidence that when using melaware utensils in boiling liquids, as for stovetop use of spatulas, the boiling action of circulating food/simulant can have an additional effect in promoting surface erosion, increasing the plastic decomposition and so elevating the melamine release.     

Comparison of the migration of melamine from melamine-formaldehyde plastics ('melaware') into various food simulants and foods themselves

A variety of melaware articles were tested for the migration of melamine into the food simulant 3% w/v acetic acid as a benchmark, and into other food simulants, beverages and foods for comparison. The results indicate that the acidity of the food simulant plays a role in promoting migration, but not by as much as might have been anticipated, since 3% acetic acid gave migration values about double those obtained using water under the same time and temperature test conditions. In contrast, migration into the fatty food simulant olive oil was not detectable and at least 20-fold lower than with the aqueous food simulants. This was expected given the solubility properties of melamine and the characteristics of the melaware plastic. Migration levels into hot acidic beverages (apple juice, tomato juice, red-fruit tea and black coffee) were rather similar to the acetic acid simulant when the same time and temperature test conditions are used, e.g. 2 h at 70°C. However, migration levels into foods that were placed hot into melaware articles and then allowed to cool on standing were much lower (6-14 times lower) than if pre-heated food was placed into the articles and then maintained (artificially) at that high temperature in the same way that a controlled time-temperature test using simulants would be conducted. This very strong influence of time and especially temperature was manifest in the effects seen of microwave heating of food or beverage in the melaware articles. Here, despite the short duration of hot contact, migration levels were similar to simulants used for longer periods, e.g. 70°C for 2 h. This is rationalized in terms of the peak temperature achieved on microwave heating, which may exceed 70°C, counterbalancing the shorter time period held hot. There was also evidence that when using melaware utensils in boiling liquids, as for stovetop use of spatulas, the boiling action of circulating food/simulant can have an additional effect in promoting surface erosion, increasing the plastic decomposition and so elevating the melamine release.     

Alternative fatty food simulants for migration testing of polymeric food contact materials.

The amounts of substances migrating from plastics into foodstuffs with high fat contents are in most cases higher than in foodstuffs with water contents. This increase in migration commonly is due to the higher solubility of the migrating organic compounds in fat compared to water. The increase in migration is not necessarily due to an increase in the substance's diffusion coefficient due to interactions between the fat and the plastic as is often assumed. Ethanol is a good simulant for fatty foods because it has little interaction with many plastics, e.g. polyolefins, migrants are readily soluble in it, and because it is easy to work with analytically. The utilizable limits of ethanol and ethanol/water mixtures as food simulants are developed from the physical background of diffusion. The use of ethanol and ethanol/water mixtures is supported by published experimental migration results.     

筷子涂层中重金属元素的暴露研究

目的研究筷子涂层中12种重金属元素(锌、铜、镍、镉、铅、汞、铬、钼、硒、砷、钡、锑)在体液模拟物和食品模拟物中的暴露。方法以胃液模拟物、唾液模拟物作为体液模拟物,以4%乙酸(V/V)、水、95%乙醇(V/V)作为食品模拟物,利用电感耦合等离子体质谱(inductively coupled plasma mass spectrometry,ICP-MS)法测定筷子涂层中12种重金属元素的溶出量和迁移量。结果对20批次筷子涂层中12种重金属元素的含量进行测试发现10种重金属元素(锌、铜、镍、镉、铅、铬、钼、硒、砷、钡)有检出,其中铅元素含量高达347660.8mg/kg。对检出的重金属元素进一步分析其在体液模拟物中的溶出量和食品模拟物中的迁移量,发现高含量的元素能通过体液模拟物溶出和食品模拟物迁移。结论筷子涂层中重金属元素可能通过3种途径暴露至人体,分别是胃液溶出、唾液溶出、食品中迁移,且涂层涂覆的位置可对重金属元素的暴露途径产生影响;胃液模拟物中溶出量是唾液模拟物中溶出量的10倍以上;4%乙酸(V/V)食品模拟物中的迁移量最多可高于水和95%乙醇(V/V)食品模拟物中的迁移量近1000倍,且随着迁移次数的增加迁移量逐渐降低。     

SiOx layer as functional barrier in polyethylene terephthalate (PET) bottles against potential contaminants from post-consumer recycled PET

The barrier effect of a silicon oxide (SiOx) coating on the inner surface of PET bottles, in terms of the ability to reduce the migration of post-consumer compounds from the PET bottle wall into food simulants (3% acetic acid and 10% ethanol), was investigated. The barrier effect was examined by artificially introducing model substances (surrogates) into the PET bottle wall to represent a worst-case scenario. Test bottles with three different spiking levels up to approximately 1000 mg kg(-1) per surrogate were blown and coated on the inner surface. The SiOx-coated bottles and the non-coated reference bottles were filled with food simulants. From the specific migration of the surrogates with different bottles wall concentrations, the maximum surrogate concentrations in the bottle wall corresponding to migration of 10 microg l(-1) were determined. It was shown that the SiOx coating layer is an efficient barrier to post-consumer compounds. The maximum bottle wall concentrations of the surrogates corresponding to migration of 10 microg l(-1) were in the range of 200 mg kg(-1) for toluene and approximately 900 mg kg(-1) for benzophenone. Consequently, the SiOx coating allows use of conventionally recycled post-consumer PET flakes (without a super-clean recycling process) for packaging aqueous and low alcoholic foodstuffs (under cold-fill conditions) and protects food from migration of unwanted contaminants from post-consumer PET.     

Migration of epoxidised soybean oil from PVC gaskets of commercial lids: simulation of migration under various conditions and screening of food products from Czech markets

Previous studies have shown that a large number of polyvinylchloride (PVC) lid gaskets exceed the existing migration limits for epoxidised soybean oil (ESBO) and correct prediction of ESBO release into food therefore appears to be a difficult issue. ESBO migration from PVC gaskets of metal closures into food simulants and food products from the Czech market is evaluated during a survey in 2009 and subsequently one in 2012 to assess progress in lid manufacturing and official testing conditions. ESBO migration from lids into various food simulants was studied at various temperatures (25, 40 and 60°C) during storage times up to 12 months. ESBO released into food simulants or food products was transmethylated, derivatised and analysed by GC-MS. The levels of ESBO migration in foodstuffs in 2012 exceeded the specific migration limit (SML) in fewer products in comparison with the previous survey. However, most of the products were analysed at a time far from the expiry date and exceedance of the SML at the end of the product shelf life is not therefore excluded. More severe test conditions (60°C for 10 days) for specific migration given by the current European Union legislation (Regulation (EU) No. 10/2011) still seem to be insufficient for the simulation of ESBO migration during long-term storage.     

蜜胺餐具中三聚氰胺单体的迁移规律研究

结合蜜胺餐具的实际使用情况,选用合适的食品模拟物进行迁移实验,采用LC-MS/MS法测定三聚氰胺迁移量,研究蜜胺餐具中三聚氰胺单体的迁移规律。重点考察了食品模拟物种类、接触时间、接触温度、乙酸浓度、乙醇浓度、重复使用和微波加热等迁移条件下蜜胺餐具中三聚氰胺迁移量的变化情况。结果表明酸性食品和牛奶中的三聚氰胺迁移风险较高,且需控制蜜胺餐具的使用温度、盛放时间、重复使用次数及微波加热功率和时间以降低密胺餐具中三聚氰胺迁移风险。     

塑料食品包装材料中有毒有害化学残留物及分析方法

食品包装材料中有毒有害化学物质的迁移是引起食品污染的重要途径之一。本文主要根据近年来发表的有关食品包装材料、卫生检测领域的相关文献为基础,针对塑料食品包装材料中的单体、低聚体、添加剂和污染物等几类有毒有害化学物质的组成、毒性、卫生限量标准及主要检测方法进行了分析,为相关食品包装企业的质量控制技术人员和科研工作者提供参考。     

Linear and cyclic oligomers in polybutylene terephthalate for food contact materials

Polybutylene terephthalate (PBT) is a polyester (PES) gaining more importance on the food contact material (FCM) market. However, little is known about the potential migration of PBT oligomers which are formed during polymer production. In this work, PBT pellets and a slotted spoon manufactured from this material by injection moulding were analysed on extractable oligomers and their migration potential into hydrophilic foods. Overall 27 oligomers (cycles and linears) could be identified in different extracts by HPLC-DAD/ESI-MS data, but without confirmation by reference substances. The oligomers were quantified by HPLC-DAD using bis(2-hydroxyethyl) terephthalate (BHET) as external standard and the total amount of oligomers isolated by reprecipitation from the pellets and the spoon were 0.69 and 0.71%, respectively. While cyclic oligomers made up for approximately 90% of the extractable oligomers, linear oligomers proved to be more relevant for migration into aqueous foodstuffs. Furthermore, it was shown that hydrolysis of oligomers can take place in water at elevated temperatures. Consequently, the qualitative and quantitative composition of PBT oligomers in aqueous foods from FCMs does not only depend on migration but also on hydrolysis. Migration testing of the PBT spoon under repeat use conditions with water at 100°C for 2 h resulted in 0.29 mg item^?1 of linear oligomers and 0.05 mg item^?1 of the cyclic PBT dimer in the third migrate.     

Migration of substances from food packaging materials to foods

The employment of novel food packaging materials has increased the number of occurring hazards due to the migration from packaging material to the packaged food. Although polymers have mainly monopolized the interest of migration testing and experimentation, recent studies have revealed that migration also occurs from "traditional" materials generally considered to be safe, such as paper, carton, wood, ceramic, and metal. The regulations and the directives of the EU tend to become stricter in this respect. The emphasis is on reaching a consensus in terms of food simulants and testing conditions for migration studies. Furthermore, the list of hazardous monomers, oligomers, and additives continues to augment in order to ensure that the consumer safety is in current agreement with the HACCP, which is continuously gaining ground.