共查询到16条相似文献,搜索用时 171 毫秒
1.
2.
太阳热反射涂料对太阳辐射具有较高反射率,将其涂覆于建筑围栏结构,可以降低空调负荷或改善室内热舒适环境。研究了不同围栏结构材料对太阳热反射涂料节能效果的影响。 相似文献
3.
4.
5.
6.
7.
8.
太阳热反射涂料的现状及发展 总被引:10,自引:2,他引:8
太阳热反射涂料的热反射率与所用的基料、颜填料的折光指数及粒径等有密不可分的关系,简单叙述了新型填料的性质及特点,概述了太阳热反射涂料的现状及其发展方向。 相似文献
9.
10.
11.
建筑反射隔热保温涂料的研制 总被引:1,自引:1,他引:1
介绍了以有机硅改性丙烯酸乳液为基料,不透明聚合物、空心微珠和红外辐射功能颜填料制备建筑反射隔热保温涂料的工艺技术,研究了几种功能颜填料及涂料体系的PVC值对涂料隔热保温性能的影响,乳液T_g值及阻燃剂对涂料耐沾污性和阻燃性能的影响。 相似文献
12.
13.
复合型反射隔热涂料的制备与性能研究 总被引:1,自引:1,他引:0
采用红外高反射率的空心玻璃珠(BLZ)和彩色空心陶瓷珠(TCZ)制备得到复合型建筑反射隔热涂料,研究了功能性填料、乳液、颜填料及颜填料粒径配比对涂料隔热效果及耐沾污性能的影响。试验结果表明,成膜物质种类的差异对涂料隔热性能的影响较小,当纯丙乳液含量为40%时,隔热温差为14.6℃;二氧化钛能有效提高涂层反射隔热性能,采用20%的二氧化钛添加量能使隔热温差达到15℃左右;填料含量为12%时,具有良好的隔热增强效果,隔热温差为14.6℃;当m(BLZ)/m(TCZ)=1:1时,涂层隔热温差为16.5℃;耐沾污测试表明,当采用纯丙乳液,钛白、硅藻土和滑石粉比例为5:1:1,m(BLZ)/m(TCZ)=2:1时,具有良好的耐沾污性能。 相似文献
14.
聚酯粉末涂料配方组成与性能研究 总被引:2,自引:0,他引:2
研究了不同厂家出产的聚酯树脂,不同固化剂及其不同用量,不同助剂、颜料品种和填料品种对聚酯粉末涂料及其涂膜性能的影响。结果表明,使用不同厂家生产的聚酯树脂所得的粉末涂料的胶化时间和熔融流动性不同;粉末的性能与固化体系有关;固化剂的用量对涂膜性能有较大的影响;流平剂的质量分数以不超过1.5%为宜;配方的设计应按用户要求,选择适宜的颜、填料品种及其用量。 相似文献
15.
针对石墨烯/水纳米流体的分散不稳定问题,采用化学方法制备了不含表面活性剂的改性石墨烯/水两亲性纳米流体,研究了以改性石墨烯/水两亲性纳米流体为工质的太阳重力热管在不同加热功率、安装角度和浓度下的热性能。结果表明,与去离子水相比,两亲性纳米流体可以降低热管的启动温度。在实验加热功率范围内,当加热功率相对较小时,两亲性纳米流体热管的热阻明显低于去离子水;随着加热功率的增加,热阻差异可以忽略。当安装角度相对较小时,其对蒸发段传热能力影响较大。当加热功率为20 W,纳米流体质量分数从0.1%增加到0.6%时,蒸发段传热系数下降了54.7%;当加热功率为40 W,纳米流体质量分数从0.1%增加到0.6%时,蒸发段传热系数下降了48.9%。 相似文献
16.
Modified graphene/deionized water (DW) based amphiphilic nanofluid (A-nanofluid) without surfactant was prepared through chemical method. The thermal performance of solar gravity heat pipe (SGHP) with A-nanofluid was investigated under different heating powers, incline angles and concentrations. It was found that A-nanofluid can reduce the start-up temperature of the SGHP compared with DW. Within the measured range of heating power, the thermal resistance of the SGHP filled with A-nanofluid is obviously lower than that with DW when the heating power is relatively small. However, the difference of thermal resistance of the SGHP filled with A-nanofluid and DW is almost negligible with the increase of heating power. The incline angle has great influence on the heat transfer capacity of the evaporation section when the incline angle is relatively small. When the heating power is 20 W and the nanofluid concentration (mass ratio) increases from 0.1% to 0.6%, the heat transfer coefficient of the evaporation section decreases by 54.7%; when the heating power is 40 W, the nanofluid concentration (mass ratio) increases from 0.1% to 0.6%, the heat transfer coefficient of the evaporation section decreases by 48.9%. 相似文献