UV-durable superhydrophobic textiles with UV-shielding properties by coating fibers with ZnO/SiO2 core/shell particles

ZnO/SiO(2) core/shell particles were fabricated by successive coating of multilayer polyelectrolytes and then a SiO(2) shell onto ZnO particles. The as-prepared ZnO/SiO(2) core/shell particles were coated on poly(ethylene terephthalate) (PET) textiles, followed by hydrophobization with hexadecyltrimethoxysilane, to fabricate superhydrophobic surfaces with UV-shielding properties. Transmission electron microscopy and ζ potential analysis were employed to evidence the fabrication of ZnO/SiO(2) core/shell particles. Scanning electron microscopy and thermal gravimetric analysis were conducted to investigate the surface morphologies of the textile and the coating of the fibers. Ultraviolet-visible spectrophotometry and contact angle measurement indicated that the incorporation of ZnO onto fibers imparted UV-blocking properties to the textile surface, while the coating of SiO(2) shell on ZnO prohibited the photocatalytic degradation of hexadecyltrimethoxysilane by ZnO, making the as-treated PET textile surface show stable superhydrophobicity with good UV-shielding properties.     

Passivation of pigment-grade TiO(2) particles by nanothick atomic layer deposited SiO(2) films

Pigment-grade TiO(2) particles were passivated using nanothick insulating films fabricated by atomic layer deposition (ALD). Conformal SiO(2) and Al(2)O(3) layers were coated onto anatase and rutile powders in a fluidized bed reactor. SiO(2) films were deposited using tris-dimethylaminosilane (TDMAS) and H(2)O(2) at 500?°C. Trimethylaluminum and water were used as precursors for Al(2)O(3) ALD at 177?°C. The photocatalytic activity of anatase pigment-grade TiO(2) was decreased by 98% after the deposition of 2?nm SiO(2) films. H(2)SO(4) digest tests were performed to exhibit the pinhole-free nature of the coatings and the TiO(2) digest rate was 40 times faster for uncoated TiO(2) than SiO(2) coated over a 24?h period. Mass spectrometry was used to monitor reaction progress and allowed for dosing time optimization. These results demonstrate that the TDMAS-H(2)O(2) chemistry can deposit high quality, fully dense SiO(2) films on high radius of curvature substrates. Particle ALD is a viable passivation method for pigment-grade TiO(2) particles.     

Effect of surface fluorination of TiO2 particles on photocatalitytic activity of a hybrid multilayer coating obtained by sol-gel method

A multilayer photoactive coating containing surface fluorinated TiO(2) nanoparticles and hybrid matrices by sol gel approach based on renewable chitosan was applied on poly(lactic acid) (PLA) film by a step wise spin-coating method. The upper photoactive layer contains nano-sized functionalized TiO(2) particles dispersed in a siloxane based matrix. For the purpose of improving TiO(2) dispersion at the air interface coating surface, TiO(2) nanoparticles were modified by silane coupling agent 1H,1H,2H,2H-perfluorooctyltriethoxysilane (FTS) with fluoro-organic side chains. An additional hybrid material consisting of chitosan (CS) cross-linked with 3-glycidyloxypropyl trimethoxy silane (GOTMS) was applied as interlayer between the PLA substrate and the upper photoactive coating to increase the adhesion and reciprocal affinity. The multilayer TiO(2)/CS-GOTMS coatings on PLA films showed a thickness of ~4-6 μm and resulted highly transparent. Their structure was exhaustively characterized by SEM, optical microscope, UV-vis spectroscopy and contact angle measurements. The photocatalytic activity of the multilayer coatings were investigated using methyl orange (MeO) as a target pollutant; the results showed that PLA films coated with surface fluorinated particles exhibit higher activity than films with neat particles, because of a better dispersion of TiO(2) particles. The mechanical properties of PLA and films coated with fluorinated particles, irradiated by UV light were also investigated; the results showed that the degradation of PLA substrate was markedly suppressed because of the UV adsorptive action of the multilayer coating.     

Novel, nanoporous silica and titania layers fabricated by magnetron sputtering

Composite asymmetric membranes are fabricated through the deposition of submicrometer thick (100 nm) silica (SiO(2)) and titania (TiO(2)) films onto flat nanoporous silica and zirconia substrates by magnetron sputtering. The deposition conditions for both coating types were systematically altered to determine their influence on the deposited coating morphology and thickness. Ideal He/N(2) gas selectivity was measured for all of the membranes. The TiO(2) coatings, when deposited onto a ZrO(2) support layer with a pore size of 3 nm, formed a long columnar grain structure with average column diameter of 38 nm. A similar columnar structure was observed for TiO(2) coatings deposited onto a SiO(2) support layer with a pore size of 1 nm. Under the same conditions, SiO(2) coatings, deposited onto the same SiO(2) supports, formed a closely packed spherical grain structure whereas, when deposited onto ZrO(2) supports, the SiO(2) coatings formed an open grain structure. The average SiO(2) grain diameter was 36 nm in both cases. This preliminary investigation was aimed at studying the effect of sputtering parameters on the density and morphology of the deposited coatings. For the depositions carried out, the coating material was found to be very dense. However, the presence of grain boundaries resulted in poor ideal He/N(2) separation efficiencies.     

New intelligent multifunctional SiO2/VO2 composite films with enhanced infrared light regulation performance,solar modulation capability,and superhydrophobicity

Abstract

Highly transparent, energy-saving, and superhydrophobic nanostructured SiO₂/VO₂ composite films have been fabricated using a sol–gel method. These composite films are composed of an underlying infrared (IR)-regulating VO₂ layer and a top protective layer that consists of SiO₂ nanoparticles. Experimental results showed that the composite structure could enhance the IR light regulation performance, solar modulation capability, and hydrophobicity of the pristine VO₂ layer. The transmittance of the composite films in visible region (T_lum) was higher than 60%, which was sufficient to meet the requirements of glass lighting. Compared with pristine VO₂ films and tungsten-doped VO₂ film, the near IR control capability of the composite films was enhanced by 13.9% and 22.1%, respectively, whereas their solar modulation capability was enhanced by 10.9% and 22.9%, respectively. The water contact angles of the SiO₂/VO₂ composite films were over 150°, indicating superhydrophobicity. The transparent superhydrophobic surface exhibited a high stability toward illumination as all the films retained their initial superhydrophobicity even after exposure to 365 nm light with an intensity of 160 mW^.cm^?2 for 10 h. In addition, the films possessed anti-oxidation and anti-acid properties. These characteristics are highly advantageous for intelligent windows or solar cell applications, given that they can provide surfaces with anti-fogging, rainproofing, and self-cleaning effects. Our technique offers a simple and low-cost solution to the development of stable and visible light transparent superhydrophobic surfaces for industrial applications.     

SiO2-TiO2自清洁防反光薄膜的制备与表征

采用溶胶-凝胶浸渍-提拉法,通过改变镀膜顺序和镀膜速率制备了TiO2/SiO2(ST)和SiO2/TiO2(TS)型的一系列SiO2改性TiO2双层薄膜.薄膜的形貌、光透性、光催化活性、亲水性等分别用场发射扫描电镜(FESEM)、分光光度计、光降解甲基橙等表征方法进行了分析.结果表明:SiO2膜层因其低反射指数,在ST...     

Facile preparation and property analyses of L-CNC/SiO2-based composite superhydrophobic coating

In recent years, superhydrophobic coatings have received extensive attention due to their functions of waterproof, antifouling, self-cleaning, etc. However, wide applications of superhydrophobic coatings are still affected by their disadvantages of complex preparation, low mechanical properties, and poor ultraviolet (UV) resistance. In this study, cellulose nanocrystal containing a small amount of lignin (L-CNC)/SiO₂ composite particles were used as the main material, polydimethylsiloxane (PDMS) as the adhesive and perfluorooctyltrichlorosilane (FOTS) as the modifier to prepare superhydrophobic coatings by a one-step spray method. The resulted coating showed excellent superhydrophobicity (water contact angle (WCA) of 161° and slide angle (SA) of 7°) and high abrasion resistance (capable of withstanding 50 abrasion cycles under the load of 50 g). Moreover, it still maintained good superhydrophobicity after 5 h of exposure to the UV light (1000 W), displaying its good UV resistance. This study provides theoretical and technical reference for the simple preparation of organic‒inorganic composite superhydrophobic coatings with high abrasion resistance and good UV resistance, which is beneficial to improving the practicability and broadening the application scope of superhydrophobic coatings.     

透明超疏水玻璃表面的制备及性能研究

目的研究透明超疏水玻璃的制备及性能。方法以纳米二氧化硅和无水乙醇为原料制成半透明乳液,然后将乳液喷涂在玻璃表面,再通过接触角测试、透光率测试仪等手段对玻璃表面的性能进行研究。结果在玻璃基材表面构建了与水滴接触角高达158°±2°,滚动角低至1°的透明超疏水表面。当喷涂液中纳米二氧化硅的质量分数为1.5%时,获得的超疏水玻璃表面具有优异的防水性、抗污易清洁性和透明性。结论在玻璃基底上制备透明超疏水表面可以大大提高玻璃表面的防水、防污性,并使玻璃表面更易于清洁,有利于减少玻璃包装材料清洗时的用水量和洗涤剂用量,从而增强玻璃包装材料的生态环保效应。     

铝合金表面超疏水涂层的火焰喷雾热解法制备及其耐蚀性能

采用火焰喷雾热解与表面修饰相结合的方法在铝合金表面制备了具有一定耐蚀性能的超疏水表面。以六甲基二硅氧烷溶液为前驱液,通过火焰喷雾热解方法,首先在铝合金表面沉积SiO2纳米颗粒构建粗糙结构,再以氟硅烷溶液进行表面修饰,获得了具有154.9°静态接触角,滚动角<2°的超疏水表面。通过电化学测试,对比了构筑超疏水表面前后的铝合金样品的耐蚀性能。结果表明沉积层与低表面能物质协同作用,通过对腐蚀性离子的有效隔离,提高了铝合金基体的耐蚀性能。     

含TiO2/(RSiO1.5)8复合物涂层的光活性与抗老化性能

通过Sol-Gel法,以(RSiO1.5)8作为载体,将纳米TiO2分散到(RSiO1.5)8网络里制得TiO2/(RSiO1.5)8纳米复合光活性粒子,并将其分散到醇酸树脂中制成含TiO2/(RSiO1.5)8的有机涂层。实验结果表明,TiO2/(RSiO1.5)8复合粒子比纯TiO2粒子拥有更强的光催化性能,含TiO2/(RSiO1.5)8复合物的有机涂层比只含有TiO2的有机涂层具有更好的抗老化性能。     

Stability,UV shielding properties,and light conversion behavior of Eu(BMDM)3@polysiloxane nanoparticles in water and polyurethane films

Bifunctional Eu(BMDM)₃@polysiloxane nanoparticles were prepared through reprecipitation–encapsulation methods using 1-(4-tert-butylphenyl)-3-(4-methoxyphenyl)-1,3-propanedione (BMDM) ligand and octyltrimethoxysilane (OTS) precursor and embedded into waterborne polyurethane (PU) coatings to fabricate transparent optical composite films. The photostability and thermostability of the nanoparticles in water and their ability to block UV and convert light when embedded in PU films were investigated. In comparison with the control Eu(BMDM)₃ nanoparticles, the Eu(BMDM)₃@polysiloxane nanoparticles, especially those prepared at a Eu(BMDM)₃/OTS mole ratio of 1:2, exhibited far superior stability under storage conditions, UV irradiation, and heating. They also showed excellent UV-shielding and highly efficient light conversion properties because of the protective polysiloxane.     

Bioinspired Superhydrophobic Highly Transmissive Films for Optical Applications

Inspired by the transparent hair layer on water plants Salvinia and Pistia, superhydrophobic flexible thin films, applicable as transparent coatings for optoelectronic devices, are introduced. Thin polymeric nanofur films are fabricated using a highly scalable hot pulling technique, in which heated sandblasted steel plates are used to create a dense layer of nano‐ and microhairs surrounding microcavities on a polymer surface. The superhydrophobic nanofur surface exhibits water contact angles of 166 ± 6°, sliding angles below 6°, and is self‐cleaning against various contaminants. Additionally, subjecting thin nanofur to argon plasma reverses its surface wettability to hydrophilic and underwater superoleophobic. Thin nanofur films are transparent and demonstrate reflection values of less than 4% for wavelengths ranging from 300 to 800 nm when attached to a polymer substrate. Moreover, used as translucent self‐standing film, the nanofur exhibits transmission values above 85% and high forward scattering. The potential of thin nanofur films for extracting substrate modes from organic light emitting diodes is tested and a relative increase of the luminous efficacy of above 10% is observed. Finally, thin nanofur is optically coupled to a multicrystalline silicon solar cell, resulting in a relative gain of 5.8% in photogenerated current compared to a bare photovoltaic device.     

透明食品包装材料防紫外性能的检测与评价

对21种透明食品包装材料进行了透射光谱分析,获得了透射光谱。将紫外线透射比评价模型引入到了透明包装材料防紫外线性能的评价中,并对该评价体系进行了验证。结果表明,该评价体系能直观、可靠地评价透明包装材料防紫外线的性能。     

All-nanoparticle thin-film coatings

All-nanoparticle thin-film coatings that exhibit antireflection, antifogging (superhydrophilicity), and self-cleaning properties have been prepared via layer-by-layer deposition of TiO(2) and SiO(2) nanoparticles. The porosity and chemical composition of the coatings were determined using a simple method that is based on ellipsometry and does not require any assumptions about the refractive indices of the constituent nanoparticles. The presence of nanopores in the TiO(2)/SiO(2) nanoparticle coatings results in superhydrophilicity as well as antireflection properties. The superhydrophilicity of contaminated coatings could also be readily recovered and retained after ultraviolet irradiation.     

Antibioadhesive Superhydrophobic Syringe Needles Inspired by Mussels and Lotus Leafs

Fouling of surfaces due to bioadhesion is one of the hurdles in terms of their practical applications. Inspired by mussel and lotus leaf, antibioadhesive superhydrophobic syringe needles are fabricated by sequential bonding of polydopamine, Ag nanoparticles, and 1H,1H,2H,2H‐perfluorodecanethiol (PFDT). The morphology and surface chemical composition of the needles are characterized. The wetting properties and antibioadhesive properties of the needles are evaluated by contact angle (CA) and sliding angle (SA) of water and various aqueous solutions, and their residues on the needles after repeatedly used for liquid handling. The superhydrophobic needles show a rough surface with a layer of PFDT, which endow them with very high CA and low SA for water and various aqueous solutions. In addition, the aqueous solutions are in the Cassie–Baxter state on the surface of the superhydrophobic needles. Thus, the adhesion force between the superhydrophobic needles and aqueous solutions is very low. This endues the needles with excellent antibioadhesive properties and can be repeatedly used for withdrawing and dispensing various aqueous solutions. Moreover, the superhydrophobic needles can be used for the transport of aqueous solutions at high accuracy. The antibioadhesive superhydrophobic needles may find applications in various fields such as liquids transport and inkjet printing devices.     

PVDF/SiO2/PDMS涂层超疏水纺织品性能

目的 针对普通纺织品材料防水性和防污性较差的问题,制备具有自清洁功能的超疏水涂层纺织品,并研究其性能.方法 以涤纶织物为基材,通过非溶剂诱导相分离法,使用聚偏氟乙烯和疏水纳米二氧化硅复合液在纺织品表面构筑微纳粗糙结构,采用聚二甲基硅氧烷对其进行疏水化处理,获得自清洁超疏水涂层纺织品.采用扫描电子显微镜、X射线能量散射光谱和视频光学接触角测量仪等对其结构和性能进行表征,并通过机械摩擦、洗涤、酸/碱/盐溶液浸渍和紫外光照等方法对其表面超疏水稳定性进行考察.结果 当聚偏氟乙烯质量分数为2％,疏水纳米二氧化硅质量分数为0.4％,聚二甲基硅氧烷质量分数为1％时,制备的纺织品的表面接触角可达(162.2°±0.8°),滚动角达(2.0°±0.4°),具有优异的超疏水自清洁效应;经72 h酸/碱/盐溶液浸渍、196 h紫外光照、2500次摩擦和120次家庭水洗后,其表面接触角仍大于150°,表现出优异的超疏水稳定性.结论 采用简便的非溶剂相分离法制备的涂层纺织品具有优异的自清洁性能,并且其超疏水性能具有机械耐久性和化学稳定性,有望应用于纺织材料包装领域.     

热处理温度对TiO2/SiO2复合气凝胶光催化性能的影响

采用溶胶–凝胶法在常压下经不同温度热处理制备了TiO2/SiO2复合气凝胶光催化剂,利用XRD、TGA和BET等手段对其微观结构进行表征,以甲基橙溶液光催化降解实验评价其光催化性能,研究了热处理温度对TiO2/SiO2复合气凝胶的微观结构及光催化性能影响规律.结果表明:随着热处理温度升高,TiO2/SiO2复合气凝胶中锐钛矿结晶度升高,晶粒尺寸增大,比表面积减小,使TiO2/SiO2复合气凝胶对甲基橙溶液的光催化降解活性呈现先升后降的变化趋势.当热处理温度为700℃左右,紫外光照20 min TiO2/SiO2复合气凝胶对甲基橙溶液的降解率达到95.4%.     

Corrosion Resistance of Plasma Sprayed Ceramic CompositeCoatings on Q235 Substrate

The corrosion resistance of SiO2/Al2O3, TiO2/Al2O3 and (SiO2+TiO2)/Al2O3 ceramic composite coatings on Q235 substrate fabricated by means of plasma spraying was investigated. The results show that Al2O3+13 wt pct TiO2 ceramic coating has the highest density, the lowest connected porosity and the best corrosion resistance. The corrosion mechanism of Q235 with ceramic coating has also been studied.     

Nanocomposite of Cu-TiO2-SiO2 with high photoactive performance for degradation of rhodamine B dye in aqueous wastewater

The nanocomposite of Cu-TiO2-SiO2 photocatalyst have been prepared by a sol-gel method, which is used for the degradation of Rhodamine B (RB) as a probe that is notorious organic compound present in dyes wastewater. Morphological and structural characteristics of the Cu-TiO2-SiO2 nanocomposite were studied with low temperature N2 adsorption (BET), X-ray diffraction (XRD), scanning electron microscopy (SEM) and UV-vis diffuse reflectance spectroscopy (DRS). The Fourier transformed infrared spectroscopy (FT-IR) analysis shows the enhanced chemical bonding of O-Ti and O-Ti-O after the composition of Cu and SiO2 species into TiO2. It is found that the Cu-TiO2-SiO2 nanocomposite exhibits much higher photocatalytic activity under both UV light and visible light irradiation as compared with that over commercial titania (Degussa P25) toward the dyes wastewater containing RB. The photodegradation rate of RB (5 mg/L) can reach above 95.0% under sunlight after 3 h. The addition of SiO2 not only inhibites the crystal growth and anatase-to-rutile transformation of TiO2 nanocatalyst, but also enhances the adsorption of organic compounds. Cu-doping extends the light response to the visible region. Synergetic effects between Cu-SiO2 and TiO2 have been investigated, which provides a good way and material in the degradation field of dyes wastewater.     

Corrosion Resistance of Plasma Sprayed Ceramic Composite Coatings on Q235 Substrate

The corrosion resistance of SiO2/A12O3, TiO2/Al2O3 and (SiO2+TiO2)/Al2O3 ceramic composite coatings on Q235 substrate fabricated by means of plasma spraying was investigated. The results show that A12O3+13 wt pct TiO2 ceramic coating has the highest density, the lowest connected porosity and the best corrosion resistance. The corrosion mechanism of Q235 with ceramic coating has also been studied.