高活性Pt／TiO2纳米管的制备及其光催化性能

采用电化学阳极氧化法和浸渍一提拉法成功制备了高度有序的Pt改性TiO2纳米管（Pt／TNT）阵列电极,并运用场发射扫描电子显微镜（FESEM）、X射线衍射（XRD）、x射线光电子能谱分析（XPS）、紫外可见漫反射光谱（UV—VisDRS）等手段对其进行表征,考察了其光电化学性质,并研究了该电极光电催化降解甲基橙染料废水的催化性能及其稳定性．结果表明,Pt的均匀负载成功地将TNT阵列电极的光响应范围拓宽到可见光区域,光电流密度达到负载前TNT阵列电极的18倍;Pt／TNT阵列电极对甲基橙的降解符合拟一级动力学,其反应速率常数为TNT阵列电极的3倍,这主要归结于Pt与TiO：间的肖特基势垒和纳米管阵列结构带来的较大比表面积、有效的光生电子和空穴的分离与传输和宽的光响应范围．     

TiO2/CdSe纳晶复合薄膜电极的光电性能研究

研究了TiO2/CdSe纳晶复合薄膜电极的瞬态光电流、光电流作用谱、光吸收特性,结果表明TiO2/CdSe纳晶复合薄膜电极阻止了CdSe上光生电子和空穴的复合,从而提高了阳极光电流的响应,获得了较高增幅的稳态光电流.     

透明纳米TiO2薄膜的制备及其紫外光电特性研究

采用溶胶-凝胶法于ITO导电玻璃和石英玻璃基底上制备了均匀透明的TiO2多孔纳米薄膜.XRD和AFM测试结果表明,构成薄膜的TiO2粒子为锐钛矿相,粒径约为50nm.紫外-可见(UV-vis)吸收光谱显示,制得的TiO2薄膜对紫外光表现出很强的吸收特性.借助标准三电极体系进行的光电化学测试结果表明,在紫外光照射下,制得的薄膜电极可产生稳定的阳极光生电流,且电流大小显著依赖于照射光的波长(λ),λ=320nm的光产生的光电流最大.另外,薄膜电极中的光电流大小与电极电位(U)有关.高于0.6V的电位可有效抑制光生电子向电解液的注入,并增大光生电子向导电基底的扩散速度,从而提高阳极光电流的大小.实验结果表明,纳米TiO2薄膜在紫外光传感器的制备方面具有较好的应用潜力.     

TiO2/SnO2复合薄膜的低温制备及其光催化性能

采用溶胶-凝胶法合成了TiO2溶胶和SnO2溶胶，使用浸渍提拉法在低温下制备出底层为金红石型SnO2，表层为锐钛矿型TiO2的复合膜．考察了不同SnO2薄膜层数对TiO2／SnO2复合膜光催化活性的影响，并对其光催化活性提高的机理进行了探讨．结果表明，SnO2层的加入能有效提高TiO2薄膜的光催化活性，随着SnO2薄膜层数的增加，光催化活性先增大后减小，但始终高于单一的TiO2薄膜．这是由于SnO2的导带电位低于TiO2的导带电位，SnO2的价带电位高于TiO2的价带电位，紫外光照下，TiO2中产生的光生电子注入到SnO2层，SnO2中空穴注入到TiO2层，有效抑制了薄膜内电子-空穴对的复合，增加了复合薄膜表面空穴的浓度，因而光催化活性得到了显著的提高．     

不同方法制备的TiO2薄膜电极光电性能比较

用Doctor-Blade和Dip-Coating方法制备了粒子膜和溶胶-粒子膜两类TiO2纳米晶薄膜电极,利用BAS—100B电化学工作站和IM-6e交流阻抗仪研究了两种电极的光电化学性能．由光电流和交流阻抗谱（EIS）的测试结果发现,由于引入溶胶,增加了TiO2纳米粒子与基底的附着力,改善了TiO2纳米粒子与基底以及TiO2纳米粒子之间的电性接触,使得溶胶-粒子膜电极的电荷转移电阻远远小于粒子膜电极,提高了溶胶-粒子膜电极的光电流．     

NiCr_2O_4/TiO_2薄膜光阳极的制备及性能研究

采用柠檬酸法制备了尖晶石型NiCr2O4纳米晶,然后掺合到P25(degussa TiO2)中,制备成NiCr2O4/TiO2薄膜光阳极,并组装成染料敏化太阳电池(DSSC),对其光电性能进行表征。研究发现NiCr2O4/TiO2形成界面势,NiCr2O4的扩散形成电势分布,促使光生电子和空穴向相反方向迁移。当NiCr2O4含量为1%(质量分数)时,与纯TiO2薄膜光阳极相比,光电转化效率(η)提高了30.8%,电池单色光转化率(IPCE)提高了13%(500nm)。     

ZnO—TiO2染料敏化太阳能电池的制备和性能

采用低温水溶液法制备ZnO纳米花,将其与TiO2纳米颗粒以不同的质量比混合制备成复合浆料,采用刮涂法涂敷在掺氟的SnOz透明导电玻璃（FTO）上制备ZnO纳米花-TiO2纳米颗粒复合薄膜光阳极,与Pt对电极和电解质组装成染料敏化太阳能电池（DSSC）。通过光伏性能和电化学阻抗谱测试分析,研究ZnO纳米花与TiO2纳米颗...     

TiO2种子层对Bi 3.15 Nd 0.85 Ti 3 O 12铁电薄膜的结晶取向和铁电性能的影响

用sol—gel法分别制备了直接沉积在Pt／Ti／SiO2／Si衬底上和加入了TiO2种子层的Bi3．15Nd0．85Ti3O12（BNT）铁电薄膜，研究了种子层对BNT薄膜结构和电学性能的影响．XRD结果表明直接沉积在Pt／Ti／SiO2／Si衬底上的BNT薄膜具有（117）和（001）的混合取向，而加入TiO2种子层之后薄膜的最强峰为（200）取向；FE-SEM显示具有TiO2种子层的BNT薄膜，其表面主要是由具有非C轴取向的晶粒组成且更为致密；直接沉积的BNT薄膜和具有TiO2种子层的BNT薄膜的剩余极化Pr值分别为26和43．6μC／cm^2，矫顽场强＆分别为91和80．5kV／cm；疲劳测试表明两种薄膜均具有良好的抗疲劳特性，TiO2种子层的引入并没有降低BNT薄膜的疲劳特性；两种薄膜的漏电流密度均在10^-6-10^-5A／cm^2之间．     

染料敏化太阳能电池阻挡层的制备及其性能研究

采用电子束蒸发法在光阳极导电玻璃基底上制备了一层致密的TiO2薄膜,并在氧氛围下进行不同温度的退火处理。以此TiO2薄膜为阻挡层来阻止电解质溶液中I3-与导电玻璃基底上光生电子的复合。分别利用X射线衍射（XRD）和X射线光电子能谱（XPS）对此薄膜的结构和成分进行表征。制备不同厚度的TiO2阻挡层薄膜并研究其对电池光电性能的影响。实验结果表明,阻挡层的引入有效地抑制了暗反应的发生,提高了染料敏化太阳能电池（DSSC）的开路电压、短路电流和光电转换效率,比未引入阻挡层的DSSC的光电转换效率提高了31.5%。     

Zn掺杂TiO2薄膜紫外探测器及其光电性能研究

采用射频磁控溅射的方法制备Zn掺杂TiO2薄膜,用XRD、SEM和UV-Vis分别表征TiO2薄膜的晶体结构、表面形貌及其紫外-可见光吸收谱.并用此材料制备Au/TiO2/An结构MSM光电导型薄膜紫外光探测器,研究其光电特性.实验结果表明,Zn掺杂TiO2紫外探测器在250 nm、5 V偏压紫外光照下光电流约为500μA,其响应度为100 A/W,平均暗电流约为0.5μA;由于ZnO/TiO2复合薄膜之间的费米能级不同而形成的内建电场作用,减少了产生的光生电子与空穴的复合,得到较强的光电流.且其光响应的上升迟豫时间约为22 s,下降响应时间约为80 s;响应时间较长是由于广泛分布于薄膜中的缺陷而造成的.结果表明Zn掺杂TiO2可作为一种良好的紫外探测材料.     

Insertion of triangulated surfaces into a meccano tetrahedral discretization by means of mesh refinement and optimization procedures

In this paper, we present a new method for inserting several triangulated surfaces into an existing tetrahedral mesh generated by the meccano method. The result is a conformal mesh where each inserted surface is approximated by a set of faces of the final tetrahedral mesh. First, the tetrahedral mesh is refined around the inserted surfaces to capture their geometric features. Second, each immersed surface is approximated by a set of faces from the tetrahedral mesh. Third, following a novel approach, the nodes of the approximated surfaces are mapped to the corresponding immersed surface. Fourth, we untangle and smooth the mesh by optimizing a regularized shape distortion measure for tetrahedral elements in which we move all the nodes of the mesh, restricting the movement of the edge and surface nodes along the corresponding entity they belong to. The refining process allows approximating the immersed surface for any initial meccano tetrahedral mesh. Moreover, the proposed projection method avoids computational expensive geometric projections. Finally, the applied simultaneous untangling and smoothing process delivers a high‐quality mesh and ensures that the immersed surfaces are interpolated. Several examples are presented to assess the properties of the proposed method.     

Certification Institutions Expected to Update and Transfer Information on Present Standards

Standards are the basis for production enterprises to organize production, ex-factory inspection, trade (delivery) and technical exchanges, product certification, quality arbitration and supervision.……     

Flow calorimeter for enthalpy increment measurements on condensed gases

A flow calorimeter for enthalpy increment measurements on condensed gases is presented. A better knowledge of the properties of the liquefied natural gas is needed, and therefore a liquid loop has been designed for our flow calorimeter. The fluid loop in the calorimeter is designed in order to avoid the two-phase region, since two phases would give compositional disturbances in the measurements. The avoidance of the two-phase region is made possible by increasing the pressure of the test fluid after the measurement section, then heating the fluid at super-critical pressure past the critical point. Finally, the fluid is throttled to the low-pressure gas state at the inlet condition of the compressor that circulates the fluid. To perform the pressure increase, a new cryogenic pump has been designed. To evaluate the new equipment, measurements were taken on liquid ethane over the temperature range 146–256 K at pressure between 0.9 and 5.1 MPa.     

Refrigerators Enter a New Era of Health Preservation Frestech initiates the establishment of China's first standard for household sterilization refrigerators

On November 30, 2007, the China Association for Standardization (CAS) held a press conference at Beijing Diaoyutai State Guest House. Leaders from the China Household Electric Appliance Research Institute, the China Household Electric Appliance Association, and the China Consumers' Association attended and made speeches.……     

Optimum-Simulation von Ernteprozessen

Zusammenfassung Bei der Gestaltung von Ernteprozessen — beispielsweise des Prozesses Mähdrusch, Körnertransport und -abnahme — als transportverbundene Fließarbeitsverfahren mit mindestens zwei verschiedenen Arbeitsmitteln gibt es einen großen Optimierungsspielraum. Solche Prozesse sind mehrstufige Bedienungsprozesse mit gemischter Anordnung der Bedienungseinrichtungen. Außerdem besitzen sie stark ausgeprägte räumliche Aspekte. Es wird vor allem gezeigt, welche Merkmale solcher Prozesse in Simulationsmodellen abgebildet sein müssen, welche Zielgrößen in Abhängigkeit von welchen Einflußgrößen unter Berücksichtigung welcher Prozeßbedingungen ermittelt werden sollten und wie der Bewertungsprozeß zur Ermittlung der gewünschten Informationen gestaltet werden muß.     

A study of centrifugal cast high boron high speed steel

In the present study a high‐boron high speed steel (HSS) roll material was designed. Many expensive alloy elements have been substituted by cheap boron alloy, and high‐boron high speed steel roll has been manufactured by centrifugal casting method. The microstructures, mechanical properties and wear resistance of centrifugal casting high‐boron high speed steel roll have been investigated by optical microscopy (OM), scanning electron microscopy (SEM), and X‐ray diffraction (XRD) analysis, hardness test, impact test and wear test. The results indicated that the solidification microstructures of high‐boron high speed steel roll consisted of M₂(B,C), (W,Mo)₂(B,C), M₃(B,C), M₂₃(B,C)₆ type borocarbides and martensite, a small amount of retained austenite. Borocarbides were continuously distributed over the grain boundary. After quenching from 1050 °C, local broken network appeared in partial borocarbides, and fine secondary borocarbide precipitated from the matrix. After tempering from 525 °C, the amount of precipitated borocarbide increased significantly. After heat treatment, the hardness of high‐boron high speed steel roll excelled 60 HRC, and its impact toughness excelled 8.0 J/cm². The single groove steel rolling amount of high‐boron high speed steel rolls increases by 500% than that of bainite cast iron roll, when the rolls are used in K₁ mill housing of bar mill.     

Thixotropy of Systems with Shear Thinning and Plastic Flow Behavior

The definition of the thixotropy is a decrease in viscosity with time in shear and a subsequent recovery of viscosity after the shear deformation is removed.We ...     

Effect of Oxide Assisted Metal Nanoparticles on Microstructure and Morphology of Gallium oxide Nanowires

Several researches have been reported about the characteristic of β-Ga2O3 nanowires which was synthesized on nickel oxide particle. But indeed, recent researches about synthesis of β-Ga2O3 nanowires on oxide-assisted transition metal are limited to nickel or cobalt oxide catalyst. In this work, Gallium oxide (β-Ga2O3 ) nanowires were synthesized by a simple thermal evaporation method from gallium powder in the range of 700 - 1000℃ using the iron, nickel, copper, cobalt and zinc oxide as a catalyst, respectively. The β-Ga2O3 nanowires with single crystalline without defects were successfully synthesized at the reaction temperature of 850, 900 and 950℃ in all the catalysts. But optimum experimental condition in synthesis of nanowires varied with the kind of catalyst. As increasing synthesis temperature,the morphology of gallium oxide nanowires changed from nanowires to nanorods, and its diameter increased. From these results, we could be proposed that the growth mechanism of β-Ga2O3 nanowires was changed with synthesis temperature of nanowires. Microstructure and morphology of Synthesized nanowire was characterized by HR-TEM, FE-SEM, EDX and XRD.     

Brainstorming for ISO Strategy 2016-2020

正Responding to ISO’s appeal for survey for the to-be-developed ISO Strategy Plan for 2016-2020,SAC hosted a special workshop over the needs and comments of various fi elds on June 8 in Beijing.The workshop was attended by ISO President-elect and Ansteel General Manager Zhang Xiaogang,SAC Vice-Administrator Yu Xinli,and 30 experts from