Improved ionic conductivity of nitrile rubber/ionic liquid composites

Polymer electrolytes with high ionic conductivity and good elasticity were prepared by mixing nitrile rubber (poly(acrylonitrile-co-butadiene) rubber; NBR) with ionic liquid, N-ethylimidazolium bis(trifluoromethanesulfonyl)imide (EImTFSI). The NBR/EImTFSI composites were obtained as homogeneous and transparent films when the ionic liquid content was less than 60 wt%. Raman spectroscopy suggested the interaction between nitrile group of NBR and TFSI anion. Sample with ionic liquid content of 50 wt% showed the ionic conductivity of 1.2×10⁻⁵ S cm⁻¹ at 30 °C. Addition of lithium salt to this NBR/EImTFSI composite further enhanced the ionic conductivity to about 10⁻⁴ S cm⁻¹ without spoiling mechanical properties. DSC studies showed two glass transition temperatures for composites indicating microphase separation.     

Synthesis and electrochemical characterization of PEO-based polymer electrolytes with room temperature ionic liquids

New gel polymer electrolytes containing 1-butyl-4-methylpyridinium bis(trifluoromethanesulfonyl)imide (BMPyTFSI) ionic liquid are prepared by solution casting method. Thermal and electrochemical properties have been determined for these gel polymer electrolytes. The addition of BMPyTFSI to the P(EO)₂₀LiTFSI electrolyte results in an increase of the ionic conductivity, and at high BMPyTFSI concentration (BMPy⁺/Li⁺ = 1.0), the ionic conductivity reaches the value of 6.9 × 10⁻⁴ S/cm at 40 °C. The lithium ion transference numbers obtained from polarization measurements at 40 °C were found to decrease as the amount of BMPyTFSI increased. However, the lithium ionic conductivity increased with the content of BMPyTFSI. The electrochemical stability and interfacial stability for these gel polymer electrolytes were significantly improved due to the incorporation of BMPyTFSI.     

Preparation of thermally stable polymer electrolytes from imidazolium-type ionic liquid derivatives

Thermally stable polymer electrolytes based on ionic liquids were prepared and analyzed. Mono-functional ionic liquid monomers, ionic liquid cross-linkers, and ethylimidazolium-type ionic liquid salts were mixed and polymerized. The ionic liquid-type cross-linkers were effective to prepare thermally stable polymer films. In particular, the copolymerization of cross-linker and ethylimidazolium-type ionic liquid monomers were used to make polymer electrolytes with high ionic conductivities. The copolymerization in ethylmethylimidazolium bis(trifluoromethanesulfonyl)imide gave a transparent film showing no thermal degradation up to 400 °C.     

Physical and electrochemical properties of 1-(2-hydroxyethyl)-3-methyl imidazolium and N-(2-hydroxyethyl)-N-methyl morpholinium ionic liquids

Various ionic liquids (ILs) were prepared via metathesis reaction from two kinds of 1-(2-hydroxyethyl)-3-methyl imidazolium ([HEMIm]⁺) and N-(2-hydroxyethyl)-N-methyl morphorinium ([HEMMor]⁺) cations and three kinds of tetrafluoroborate ([BF₄]⁻), bis(trifluoromethanesulfonyl)imide ([TFSI]⁻) and hexafluorophosphate ([PF₆]⁻) anions. All the [HEMIm]⁺ derivatives were in a liquid state at room temperature. In particular, [HEMIm][BF₄] and [HEMIm][TFSI] showed no possible melting point from −150 °C to 200 °C by DSC analysis, and their high thermal stability until 380-400 °C was verified by TGA analysis. Also, their stable electrochemical property (electrochemical window of more than 6.0 V) and high ionic conductivity (0.002-0.004 S cm⁻¹) further confirm that the suggested ILs are potential electrolytes for use in electrochemical devices. Simultaneously, the [HEMMor]⁺ derivatives have practical value in electrolyte applications because of their easy synthesis procedures, cheap morpholinium cation sources and possibilities of high Li⁺ mobility by oxygen group in the morpholinium cation. However, [HEMMor]⁺ derivatives showing high viscosity usually had lower ionic conductivities than [HEMIm]⁺ derivatives.     

1-Alkyl-2,3-dimethylimidazolium bis(trifluoromethanesulfonyl)imide ionic liquids as highly safe electrolyte for Li/LiFePO4 battery

Several 1-alkyl-2,3-dimethylimidazolium bis(trifluoromethanesulfonyl)imide ionic liquids (alkyl-DMimTFSI) were prepared by changing carbon chain lengths and configuration of the alkyl group, and their electrochemical properties and compatibility with Li/LiFePO₄ battery electrodes were investigated in detail. Experiments indicated the type of ionic liquid has a wide electrochemical window (−0.16 to 5.2 V vs. Li⁺/Li) and are theoretically feasible as an electrolyte for batteries with metallic lithium as anode. Addition of vinylene carbonate (VC) improves the compatibility of alkyl-DMimTFSI-based electrolytes towards lithium anode and LiFePO₄ cathode, and enhanced the formation of solid electrolyte interface to protect lithium anodes from corrosion. The electrochemical properties of the ionic liquids obviously depend on carbon chain length and configuration of the alkyl, including ionic conductivity, viscosity, and charge/discharge capacity etc. Among five alkyl-DMimTFSI-LiTFSI-VC electrolytes, Li/LiFePO₄ battery with the electrolyte-based on amyl-DMimTFSI shows best charge/discharge capacity and reversibility due to relatively high conductivity and low viscosity, its initial discharge capacity is about 152.6 mAh g⁻¹, which the value is near to theoretical specific capacity (170 mAh g⁻¹). Although the battery with electrolyte-based isooctyl-DMimTFSI has lowest initial discharge capacity (8.1 mAh g⁻¹) due to relatively poor conductivity and high viscosity, the value will be dramatically added to 129.6 mAh g⁻¹ when 10% propylene carbonate was introduced into the ternary electrolyte as diluent. These results clearly indicates this type of ionic liquids have fine application prospect for lithium batteries as highly safety electrolytes in the future.     

Ionic liquid electrolytes based on multi-methoxyethyl substituted ammoniums and perfluorinated sulfonimides: Preparation, characterization, and properties

New functionalized ionic liquids (ILs), comprised of multi-methoxyethyl substituted quaternary ammonium cations (i.e. [N(CH₂CH₂OCH₃)_4−n(R)_n]⁺; n = 1, R = CH₃OCH₂CH₂; n = 1, R = CH₃, CH₂CH₃; n = 2, R = CH₃CH₂), and two representative perfluorinated sulfonimide anions (i.e. bis(fluorosulfonyl)imide (FSI⁻) and bis(trifluoromethanesulfonyl)imide (TFSI⁻)), were prepared. Their fundamental properties, including phase transition, thermal stability, viscosity, density, specific conductivity and electrochemical window, were extensively characterized. These multi-ether functionalized ionic liquids exhibit good capability of dissolving lithium salts. Their binary electrolytes containing high concentration of the corresponding lithium salt ([Li⁺] >1.6 mol kg⁻¹) show Li⁺ ion transference number (tLi⁺) as high as 0.6-0.7. Their electrochemical stability allows Li deposition/stripping realized at room temperature. The desired properties of these multi-ether functionalized ionic liquids make them potential electrolytes for Li (or Li-ion) batteries.     

Effect of the alkyl group on the synthesis and the electrochemical properties of N-alkyl-N-methyl-pyrrolidinium bis(trifluoromethanesulfonyl)imide ionic liquids

The effect of the alkyl side group on the synthesis and the electrochemical properties of N-alkyl-N-methylpyrrolidinium bis(trifluoromethanesulfonyl)imide (PYR_1ATFSI) ionic liquids (ILs) is reported. The investigation was focused on the PYR_1ATFSI ionic liquid family because of the interesting electrochemical properties of the members with propyl and butyl side chains. Side alkyl groups (A = C_nH_2n+1 with n ranging from 1 to 10) of different length and structure were used for the synthesis of PYR_1ATFSI materials. NMR and DSC have shown that the ionic liquids were correctly synthesized with the exception of the compounds with tertiary side chains. Most of the materials exhibited a conductivity higher than 10⁻³ S cm⁻¹ already at 12 °C. In the molten state a moderate conductivity decrease was observed with increasing the length and the branching of the side chain (C₂H_2n+1) group according with the change of viscosity of the ionic liquids. Most of the PYR_1ATFSI samples exhibited an electrochemical stability window exceeding 5 V.     

Asymmetrical dicationic ionic liquids based on both imidazolium and aliphatic ammonium as potential electrolyte additives applied to lithium secondary batteries

Asymmetrical dicationic ionic liquids based on the combination of imidazolium and aliphatic ammonium cations with TFSI anion, MIC_nN₁₁₁-TFSI₂, have been synthesized for the first time, wherein MI represents imidazolium cation, N₁₁₁ represents trimethylammonium cation, and C_n represents spacer length. The physical and electrochemical properties of this family of ionic liquids were studied. 1-(3-Methylimidazolium-1-yl)ethane-(trimethylammonium) bi[bis(trifluoromethane-sulfonyl) imide] (MIC₂N₁₁₁-TFSI₂) shows solid-solid transition characteristics. 1-(3-Methylimidazolium-1-yl)pentane-(trimethylammonium) bi[bis(trifluoromethan-esulfonyl)imide] (MIC₅N₁₁₁-TFSI₂) has one of the lowest solid-liquid transformation temperatures among analogues, and belongs to the greatest thermal stable ionic liquids. Additionally, it has an order of conductivity of 10⁻¹ ms cm⁻¹, and electrochemical window of about 3.7 V at room temperature. To evaluate the potential of MIC₅N₁₁₁-TFSI₂ as an additive of electrolyte for lithium secondary batteries, cells composed of LiMn₂O₄ cathode/1 M LiPF₆ in EC:DMC (1:1, v/v) electrolytic solution containing 5 wt% of MIC₅N₁₁₁-TFSI₂/lithium metal anode have been prepared. The charge-discharge cycling test reveals that unlike the cases of Li/LiMn₂O₄ cells employing a conventional electrolyte with a monocationic ionic liquid, such as 1-ethyl-3-methylimidazolium bis(trifluoromethanesulfonyl) imide (EtMeImTFSI) as an additive, the performances of Li/LiMn₂O₄ cells do not drop with the addition of MIC₅N₁₁₁-TFSI₂ at 1C rate, moreover, the cell exhibits better discharge capacity and cycle durability compared with the cell using the conventional electrolyte.     

Ionic conductivity of polymer gels deriving from alkali metal ionic liquids and negatively charged polyelectrolytes

We have prepared polymer gel electrolytes with alkali metal ionic liquids (AMILs) that inherently contain alkali metal ions. The AMIL consisted of sulfate anion, imidazolium cation, and alkali metal cation. AMILs were mixed directly with poly(3-sulfopropyl acrylate) lithium salt or poly(2-acrylamido-2-methylpropanesulfonic acid) lithium salt to form polymer gels. The ionic conductivity of these gels decreased with increasing polymer fraction, as in general ionic liquid/polymer mixed systems. At low polymer concentrations, these gels displayed excellent ionic conductivity of 10⁻⁴ to 10⁻³ S cm⁻¹ at room temperature. Gelation was found to cause little change in the diffusion coefficient of the ionic liquid, as measured by pulse-field-gradient NMR. These data strongly suggest that the lithium cation migrates in successive pathways provided by the ionic liquids.     

Cycling stability of a hybrid activated carbon//poly(3-methylthiophene) supercapacitor with N-butyl-N-methylpyrrolidinium bis(trifluoromethanesulfonyl)imide ionic liquid as electrolyte

A long cycle-life, high-voltage supercapacitor featuring an activated carbon//poly(3-methylthiophene) hybrid configuration with N-butyl-N-methylpyrrolidinium bis(trifluoromethanesulfonyl)imide ionic liquid, a solvent-free green electrolyte, was developed. The cyclability of a laboratory scale cell with electrode mass loading sized for practical uses was tested at 60 °C over 16,000 galvanostatic charge-discharge cycles at 10 mA cm⁻² in the 1.5 and 3.6 V voltage range. The reported average and maximum specific energy and power, specific capacitance and capacity, equivalent series resistance and coulombic efficiency over cycling demonstrate the long-term viability of this ionic liquid as green electrolyte for high-voltage hybrid supercapacitors.     

Effect of water and oxygen traces on the cathodic stability of N-alkyl-N-methylpyrrolidinium bis(trifluoromethanesulfonyl)imide

Although research in the field of ionic liquids for electrochemical applications has led to a deeper knowledge in their electrochemical properties, doubts in the interpretation of the experimental results are still encountered in the literature due to the poor control of the experimental conditions and/or to the limited number of experiments conducted. In this work, the effect of water and oxygen traces on the cathodic stability window of hydrophobic, air-stable ionic liquids composed of N-alkyl-N-methylpyrrolidinium (PYR_1A⁺) cations and bis(trifluoromethanesulfonyl)imide (TFSI⁻) anion, is reported. The extensive investigation performed by linear sweep voltammetry (LSV) and cyclic voltammetry (CV) indicates that the TFSI⁻ anion is cathodically stable if the ionic liquid is pure and dry. The N-alkyl-N-methylpyrrolidinium bis(trifluoromethanesulfonyl)imide ionic liquids investigated showed featureless cathodic linear sweep voltammetry curves before the massive cation decomposition took place at very low potentials.     

Accelerating rate calorimetry studies of the reactions between ionic liquids and charged lithium ion battery electrode materials

Using accelerating rate calorimetry (ARC), the reactivity between six ionic liquids (with and without added LiPF₆) and charged electrode materials is compared to the reactivity of standard carbonate-based solvents and electrolytes with the same electrode materials. The charged electrode materials used were Li₁Si, Li₇Ti₄O₁₂ and Li_0.45CoO₂. The experiments showed that not all ionic liquids are safer than conventional electrolytes/solvents. Of the six ionic liquids tested, 1-ethyl-3-methylimidazolium bis(fluorosulfonyl)imide (EMI-FSI) shows the worst safety properties, and is much worse than conventional electrolyte. 1-Ethyl-3-methylimidazolium bis(trifluoromethanesulfonyl)imide (EMI-TFSI) and 1-propyl-1-methylpyrrolidinium bis(fluorosulfonyl)imide (Py13-FSI) show similar reactivity to carbonate-based electrolyte. The three ionic liquids 1-butyl-2,3-dimethylimidazolium bis(trifluoromethanesulfonyl)imide (BMMI-TFSI), 1-butyl-1-methylpiperidinium bis(trifluoromethanesulfonyl)imide (Pp14-TFSI) and N-trimethyl-N-butylammonium bis(trifluoromethanesulfonyl)imide (TMBA-TFSI) show similar reactivity and are much safer than the conventional carbonate-based electrolyte. A comparison of the reactivity of ionic liquids with common anions and cations shows that ionic liquids with TFSI⁻ are safer than those with FSI⁻, and liquids with EMI⁺ are worse than those with BMMI⁺, Py13⁺, Pp14⁺ and TMBA⁺.     

Impedance study of protecting film formation on lithium and lithiated graphite induced by bis(fluorosulfonyl) imide anion

The process of Li⁺ reduction from room temperature ionic liquids consisting of N-methyl-N-propylpyrrolidinium cation (MPPyr⁺) and bis(fluorosulfonyl) imide (FSI⁻) or bis(trifluoromethanesulfonyl) imide (TFSI⁻) anions was studied with the use of impedance spectroscopy. Reduction was carried out on both metallic lithium (Li) and graphite (G) electrodes. It has been found that the FSI anion in high amounts is able to form a protective film on both graphite and metallic lithium. The Li⁺/Li couple should rather be represented by a Li⁺/SEI/Li system. The SEI structure depends on the manner of its formation (chemical or electrochemical) and is not stable with time. The rate constant for the Li⁺ + e⁻ → Li process at the Li/SEI/Li⁺ (in MPPyrFSI) interface is k_o = 4.2 × 10⁻⁵ cm/s. In the case of carbon electrodes (G/SEI/Li⁺ interface), lithium diffusion in solid graphite is the rate determining step, reducing current by ca. two orders of magnitude, from ca. 10⁻⁴ A/cm², characteristic of the Li/SEI/Li⁺ electrode, to ca. 10⁻⁶ A/cm².     

Electrochemical properties of novel ionic liquids for electric double layer capacitor applications

An aliphatic quaternary ammonium salt which has a methoxyethyl group on the nitrogen atom formed an ionic liquid (room temperature molten salt) when combined with the tetrafluoroborate (BF₄⁻) and bis(trifluoromethylsulfonyl)imide [TFSI; (CF₃SO₂)₂N⁻] anions. The limiting oxidation and reduction potentials, specific conductivity, and some other physicochemical properties of the novel ionic liquids, N,N-diethyl-N-methyl-N-(2-methoxyethyl)ammonium tetrafluoroborate (DEME-BF₄) and DEME-TFSI have been evaluated and compared with those of 1-ethyl-3-methylimidazolium tetrafluoroborate. DEME-BF₄ is a practically useful ionic liquid for electrochemical capacitors as it has a quite wide potential window (6.0 V) and high ionic conductivity (4.8 mS cm⁻¹ at 25 °C). We prepared an electric double layer capacitor (EDLC) composed of a pair of activated carbon electrodes and DEME-BF₄ as the electrolyte. This EDLC (working voltage ∼2.5 V) has both, a higher capacity above room temperature and a better charge-discharge cycle durability at 100 °C when compared to a conventional EDLC using an organic liquid electrolyte such as a tetraethylammonium tetrafluoroborate in propylene carbonate.     

Effect of a novel amphipathic ionic liquid on lithium deposition in gel polymer electrolytes

A novel dimeric ionic liquid based on imidazolium cation and bis(trifluoromethanesulfonyl) imide (TFSI) anion has been synthesized through a metathesis reaction. Its chemical shift values and thermal properties are identified via ¹H nuclear magnetic resonance (NMR) imaging and differential scanning calorimetry (DSC). The effect of the synthesized dimeric ionic liquid on the interfacial resistance of gel polymer electrolytes is described. Differences in the SEM images of lithium electrodes after lithium deposition with and without the 1,1′-pentyl-bis(2,3-dimethylimidazolium) bis(trifluoromethane-sulfonyl)imide (PDMITFSI) ionic liquid in gel polymer electrolytes are clearly discernible. This occurs because the PDMITFSI ionic liquid with hydrophobic moieties and polar groups modulates lithium deposit pathways onto the lithium metal anode. Moreover, high anodic stability for a gel polymer electrolyte with the PDMITFSI ionic liquid was clearly observed.     

Molten lithium sulfonimide salt having poly(propylene oxide) tail

Poly(propylene oxide) (PPO) tailed lithium(trifluoromethyl sulfonylimide)s (TFSI-PPO) were prepared as non-onium type ionic liquid polymers. Introduction of PPO chain to the TFSI salt group resulted in lower the glass transition temperature (T_g) and induce the salt dissociation. The TFSI-PPO showed relatively high ionic conductivity owing to the high dissociation degree of the TFSI salt group. The maximum ionic conductivity of 3.3×10⁻⁶ S cm⁻¹ was observed at 30 °C for TFSI salt having PPO tail with number average molecular weight of 850. On the other hand, PPOs having the same salt moiety on both chain ends ((TFSI)₂-PPO) showed higher T_g than that of TFSI-PPOs. The lithium transference number of the (TFSI)₂-PPO with PPO chain length of Mn=2000 was 0.74 in spite of slightly lower ionic conductivity.     

Proton conducting membrane containing room temperature ionic liquid

A new proton conducting membrane containing room temperature ionic liquid: 2,3-dimethyl-1-octylimidazolium trifluoromethanesulfonylimide (DMOImTFSI) and polyvinylidenefluoride-co-hexafluoropropylene (PVdF-HFP) has been developed in the present work. The addition of bis(trifluoromethanesulphonyl)imide (HN(CF₃SO₂)₂) to this membrane results in an increase in conductivity by one order of magnitude at 25 °C. The membrane shows a conductivity of 2.74 × 10⁻³ S/cm at 130 °C along with good mechanical stability. The membrane was tested in a commercial fuel cell test station at 100 °C with dry hydrogen and oxygen gas reactants using Pt/C electrodes. The membrane containing the ionic liquid has been found to be electroactive for hydrogen oxidation and oxygen reduction at the platinum electrode and can be developed for use in proton exchange membrane fuel cell (PEMFC) under non-humid conditions at elevated temperatures.     

The effects of LiBOB additive for stable SEI formation of PP13TFSI-organic mixed electrolyte in lithium ion batteries

A safe electrolyte system is prepared from N-methyl-N-propylpiperidinium bis (trifluoromethanesulfonyl) imide (PP13TFSI), organic electrolyte (1 mol L⁻¹ LiPF₆/EC-DEC) and lithium bis (oxalato) borate (LiBOB). The additive of LiBOB enhances the stability of interface between electrolyte and anode. The LiBOB-containing mixed electrolytes show non-flammability and good compatibility with active materials. The performance of anode for lithium ion battery is successfully improved by LiBOB-containing mixed electrolytes, which shows 200 mA h g⁻¹ reversible capacities at 0.3 C rate. The ionic conductivity and the lithium ion transference number in LiBOB-containing mixed electrolytes system also suits to application for lithium ion battery.     

Electrochemical investigations of ionic liquids with vinylene carbonate for applications in rechargeable lithium ion batteries

Ionic liquids based on methylpropylpyrrolidinium (MPPY) and methylpropylpiperidinium (MPPI) cations and bis(trifluoromethanesulfonyl)imide (TFSI) anion have been synthesized and characterized by thermal analysis, cyclic voltammetry, impedance spectroscopy as well as galvanostatic charge/discharge tests. 10 wt% of vinylene carbonate (VC) was added to the electrolytes of 0.5 M LiTFSI/MPPY.TFSI and 0.5 M LiTFSI/MPPI.TFSI, which were evaluated in Li || natural graphite (NG) half cells at 25 °C and 50 °C under different current densities. At 25 °C, due to their intrinsic high viscosities, the charge/discharge capacities under the current density of 80 μA cm⁻² were much lower than those under the current density of 40 μA cm⁻². At 50 °C, with reduced viscosities, the charge/discharge capacities under both current densities were almost indistinguishable, which were also close to the typical values obtained using conventional carbonate electrolytes. In addition, the discharge capacities of the half cells were very stable with cycling, due to the effective formation of solid electrolyte interphase (SEI) on the graphite electrode. On the contrary, the charge/discharge capacities of the Li || LiCoO₂ cells using both ionic liquid electrolytes under the current density of 40 μA cm⁻² decreased continually with cycling, which were primarily due to the low oxidative stability of VC on the surface of LiCoO₂.     

Solvents in salt electrolyte: Benefits and possible use as electrolyte for lithium-ion battery

An EC/DEC [40:60% (v/v)] solvent mixture has been added in various amounts to the ionic liquid (IL) hexyltrimethylammonium bis(trifluoromethylsulfonyl)imide (N₁₁₁₆-NTf₂) in the presence of LiNTf₂ (lithium bis(trifluoromethylsulfonyl)imide) as lithium salt for possible use as electrolytes in lithium-ion batteries. These electrolytes exhibit a larger thermal stability than the reference electrolyte EC/DEC [40:60] + LiNTf₂ 1 M when the percentage of the IL exceeds 30% (v/v). All studied electrolytes are glass forming ones with an ideal glass transition temperature of ca. −85 °C(±5 °C), which has been determined by application of the VTF theory to conductivity and viscosity measurements and confirmed by DSC (T_g = −90 ± 5 °C). An electrochemical window of about 5 V versus Li/Li⁺ was measured at a glassy carbon electrode. The cycling ability of the optimized electrolyte N₁₁₁₆-NTf₂/EC:DEC (40/60% (v/v)) + 1 M LiNTf₂ has been investigated at a titanate oxide (Li₄Ti₅O₁₂) and a cobalt oxide (Li_xCoO₂) electrodes. Cycling the positive and the negative electrodes was conducted successfully with a high capacity and without any significant fading.