Investigation on diffusion behavior of Li in LiFePO4 by capacity intermittent titration technique (CITT)

Capacity intermittent titration technique (CITT) was used to investigate the chemical diffusion coefficient () of lithium-ion in LiFePO₄ cathode material. The values of at the galvano-charge current of 0.2 and 0.4 mA were respectively found to range from 8.8 × 10⁻¹⁶ to 8.9 × 10⁻¹⁴ cm² s⁻¹ and from 1.2 × 10⁻¹⁶ to 8.5 × 10⁻¹⁴ cm² s⁻¹ in the voltage range from 3.2 to 4 V (vs. Li⁺/Li). The transfer coefficients of cathode (0.32-0.42) and anodic (0.26-0.3), and the standard rate constant (1.58 × 10⁻⁹ to 1.30 × 10⁻⁸ cm s⁻¹) were measured from the Tafel plots of LiFePO₄ in the equilibrium potential range from 3.06 to 3.45 V. From these kinetic parameters, the finite kinetics at interface was taken into account to revise the above values of . The revised values of at the galvano-charge current of 0.2 and 0.4 mA were respectively found to range from 2.44 × 10⁻¹⁵ to 2.21 × 10⁻¹³ cm² s⁻¹ and from 5.81 × 10⁻¹⁶ to 3.22 × 10⁻¹³ cm² s⁻¹ in the voltage range from 3.2 to 4 V. Results show that the approximation of infinite charge-transfer kinetics leads to a spurious value of which is lower than the revised value, and the spurious extent depends on the galvano-charge current of CITT experiment.     

Electroreduction of peroxycitric acid coexisting with hydrogen peroxide in aqueous solution

The electrochemical reduction of peroxycitric acid (PCA) coexisting with citric acid and hydrogen peroxide (H₂O₂) in the equilibrium mixture was extensively studied at a gold electrode in acetate buffer solutions containing 0.1 M Na₂SO₄ (pH 2.0-6.0) using cyclic and hydrodynamic voltammetric, and hydrodynamic chronocoulometric measurements. The reduction of PCA was characterized to be an irreversible, diffusion-controlled process, and the cyclic voltammetric reduction peak potential () was found to be more positive by ca. 1.0 V than that of the coexisting H₂O₂, e.g., the values obtained at 0.1 V s⁻¹ for PCA and H₂O₂ were 0.35 and −0.35 V, respectively, vs. Ag|AgCl|KCl (sat.) at pH 3.3. The of PCA was found to depend on pH, i.e., at pH > 4.5, the plot of vs. pH gave the slope (−64 mV decade⁻¹) which is close to the theoretical value (−59 mV decade⁻¹) for an electrode process involving the equal number of electron and proton in the rate-determining step, while at pH < 4.5, the was almost independent of pH. The relevant electrochemical parameters, Tafel slope, number of electrons, formal potential (E⁰′), cathodic transfer coefficient and standard heterogeneous rate constant (k⁰′) for the reduction of PCA and the diffusion coefficient of PCA were determined to be ca. 100 mV decade⁻¹, 2, 1.53 V (at pH 2.6), 0.29, 1.2 × 10⁻¹² cm s⁻¹ and 0.29 × 10⁻⁵ cm² s⁻¹, respectively, and except for E⁰′, the obtained values were almost independent of the solution pH. The overall mechanism of the reduction of PCA was discussed.     

Electrochemical behaviour of americium ions in LiCl-KCl eutectic melt

This work presents a study on the electrochemical properties of AmCl₃ in a molten LiCl-KCl eutectic, at a temperature range of 733-833 K. Transient electrochemical techniques, such as cyclic voltammetry and chronopotentiometry, on inert metallic tungsten working electrode have been used to investigate the reduction mechanism of Am³⁺ ions. The results show that Am³⁺ is reduced to Am metal by a two-step mechanism corresponding to the Am³⁺/Am²⁺ and Am²⁺/Am⁰ transitions. Formal standard potentials of Am³⁺/Am²⁺ ( versus Cl₂/Cl⁻ at 733 K) and Am²⁺/Am⁰ ( versus Cl₂/Cl⁻ at 733 K) redox couples as well as diffusion coefficients of Am³⁺ and Am²⁺ (2.4 × 10⁻⁵ and 1.15 × 10⁻⁵ cm² s⁻¹ at 733 K, respectively) have been calculated at three different temperatures. In the studied range of temperature, the DAm3+/DAm2+ ratio was found to be around 2. In addition, thermodynamic properties have been calculated for Am³⁺ () and Am²⁺ () and compared to thermodynamic reference data in order to estimate activity coefficients (Am³⁺ = 4.7 × 10⁻³ and Am²⁺ = 2.7 × 10⁻² at 733 K) in the molten LiCl-KCl eutectic.     

Relative stabilities of Ce(IV) and Ce(III) limiting carbonate complexes at 5-50 °C in Na aqueous solutions, an electrochemical study

The normal potential of the Ce(IV)/Ce(III) redox couple was determined by square wave voltammetry (SWV) at different temperatures in solutions with a constant ratio [CO₃²⁻]/[HCO₃⁻] ≈10 for high ionic strengths (3.29 mol dm⁻³ at 4.39 mol dm⁻³): varies from 259.5 to 198.0 mV/S.H.E. in the 15-50 °C range. Linear variations were found for versus (RT/F)ln(mCO₃²⁻), leading to the stoichiometry, Ce(CO₃)₆⁸⁻ for the Ce(IV) limiting complex. But the slopes of these linear variations were actually found in the range 1.8-1.9, not exactly 2. This was interpreted as dissociation of the Ce(IV) limiting complex following the reaction: Ce(CO₃)₅⁶⁻ + CO₃²⁻ → Ce(CO₃)₆⁸⁻ and as dissociation of the Ce(III) limiting complex following the reaction: Ce(CO₃)₃³⁻ + CO₃²⁻ → Ce(CO₃)₄⁵⁻; for which maximum possible values of log₁₀ K_IV,6 and log₁₀ K_III,4 were estimated via fitting in the 15-50 °C temperature range (log₁₀ K_IV,6 = 0.42 (0.97) and log₁₀ K_III,4 = 0.88 (7.00) at 15 °C (50 °C). The normal potential was found to decrease linearly with T, these variations correspond to , with T⁰ = 298.15 K and . The apparent diffusion coefficient of Ce(IV) was determined by direct current polarography (DCP), cyclic voltammetry (CV) and square wave voltammetry. It was found to depend on the ionic strength and to be proportional to T.     

Determination of heavy metal ions in mixed solution by imprinted SAMs

Specific selectivity toward different heavy metal ions could be introduced into self-assembled monolayers (SAMs) by ion imprinting. In the mixed solution, good response toward mercury ions could be obtained on mercury ions imprinted SAMs, the copper ions imprinted SAMs presented good selectivity toward copper ions, while on lead ions imprinted SAMs, significantly higher insertion of lead ions than mercury and copper ions were observed. Linear calibration plots were obtained for each heavy metal ion and the regression equations were: [Hg(II)]/(10⁻⁶ M), [Cu(II)]/(10⁻⁶ M) and [Pb(II)]/(10⁻⁶ M) for mercury, copper and lead ions, respectively. The detection limits were determined to be: 1.46×10⁻⁸ M for Hg(II), 3.73×10⁻⁸ M for Cu(II) and 4.34×10⁻⁸ M Pb(II). The decreases in current response for mercury, copper and lead ions in the presence of 100-fold interferential ions were: 3.37%, 9.16% and 7.60%, respectively. Acceptable recoveries were obtained in mixed solutions at both high and low concentrations.     

Cyclic voltammetry and scanning electrochemical microscopy studies of methylene blue immobilized on the self-assembled monolayer of n-dodecanethiol

Electron transfer (ET) kinetics through n-dodecanethiol (C₁₂SH) self-assembled monolayer on gold electrode was studied using cyclic voltammetry (CV), scanning electrochemical microscopy (SECM) and electrochemical impedance spectroscopy (EIS). An SECM model for compensating pinhole contribution, was used to measure the ET kinetics of solution-phase probes of ferrocyanide/ferricyanide (Fe(CN)₆^4−/3−) and ferrocenemethanol/ferrociniummethanol (FMC^0/+) through the C₁₂SH monolayer yielding standard tunneling rate constant () of (4 ± 1) × 10⁻¹¹ and (3 ± 1) × 10⁻¹⁰ cm s⁻¹ for Fe(CN)₆^4−/3− and FMC^0/+ respectively. Decay tunneling constants (β) of 0.97 and 0.96 Å⁻¹ for saturated alkane thiol chains were obtained using Fe(CN)₆⁴⁻ and FMC respectively. Also, it was found that methylene blue (MB) molecules are effectively immobilized on the C₁₂SH monolayer and can mediate the ET between the solution-phase probes and underlying gold substrate. SECM-mediated model was used to simultaneously measure the bimolecular ET between the solution-phase probes and the monolayer-immobilized MB molecules, as well as tunneling ET between the monolayer-immobilized MB molecules and the underlying gold electrode, allowing the measurement of k_BI = (5 ± 1) × 10⁶ and (4 ± 2) × 10⁷ cm³ mol⁻¹ s⁻¹ for the bimolecular ET and and (7 ± 3) × 10⁻² s⁻¹ for the standard tunneling rate constant of ET using Fe(CN)₆^4−/3− and FMC^0/+ probes respectively.     

Study on physical and electrostatic interactions of counterions in poly(perfluorosulfonic) acid matrix: Characterization of diffusion properties of membrane using radiotracers

The self-diffusion coefficients of water and ions were used to study the physical (tortuosity) and electrostatic interactions of counterions in poly(perfluorosulfonic) acid membrane (Nafion-117) matrix. The self-diffusion coefficients of water were measured in the water swollen Nafion-117 membrane with Zn²⁺, Ca²⁺, Sr²⁺, and Fe²⁺ counterions by analyzing the experimental exchange rates between tritium tagged water (HTO) in membrane and equilibrating water. In order to study the effects of equilibrating solution, the HTO-desorption rate profiles between the membrane samples in H⁺ or Cs⁺ forms and equilibrating solution containing CsCl or HCl (0.25 mol/L) were measured. It was observed that the HTO-exchange rate profile was slower in case of membrane sample in Cs⁺-from equilibrated with salt/acid solution than that equilibrated with deionized water in same ionic form. However, HTO-exchange rate profile did not alter in case of H⁺-form of membrane on equilibration with salt or acid solution. The variation of ln  with polymer volume function V_p/(1 − V_p), where V_p is polymer volume fraction, indicated that: (i) in the membrane with multivalent counterions was lower than that reported for membrane with monovalent counterions at same V_p, and (ii) the linear trends observed in variation of ln  with V_p/(1 − V_p) for multivalent and monovalent counterions were significantly different. The values of in membrane normalized with at V_p = 0 were taken as an estimate of the tortuosity factor for self-diffusion of ions in the membrane matrix. The self-diffusion coefficients of ions reported in the literature along with tortuosity factor obtained from in the corresponding ionic forms of the membrane were analyzed to obtain the charge (Z_i) independent electrostatic interaction parameter g(φ) of monovalent and divalent ions in the membrane. This analysis indicated that g(φ) also vary exponentially as a function of V_p/(1 − V_p) irrespective of charge on counterions. In order to study the influence of V_p on diffusional transport rates of Na⁺ and Cs⁺ ions in membrane, a permeation experiment was carried out using H⁺-form of membrane having high water volume fraction. The diffusional transport rates of Cs⁺ and Na⁺ in H⁺-form of membrane were found to be similar indicating that the water volume fraction in membrane has strong influence on the parameters that govern the diffusion across the Nafion-117 membrane.     

Anomalous IR optical properties of aggregates of Pd nanoparticles induced through electrochemical cyclic voltammetry

IR optical properties of Pd nanoparticles with different size and aggregation state were studied in the current paper. The dispersed Pd nanoparticles () stabilized with poly(N-vinylpyrrolidone) (PVP) were synthesized by the seeding growth method, in which the seeds were formed step by step through reducing H₂PdCl₄ with ethanol. The dispersed Pd nanoparticles of much large size () were grown from the by keeping the colloid of undisturbed for 150 days at room temperature around 20 °C. The aggregates of () were prepared through an agglomeration process induced during a potential cyclic scanning between −0.25 V and 1.25 V for 20 min at a scan rate of 50 mV s⁻¹. Scanning electron microscope (SEM) patterns confirmed such aggregation of . Fourier transform infrared (FTIR) spectroscopy together with CO adsorption as probe reaction was employed in studies of IR optical properties of the prepared Pd nanoparticles. The results demonstrated that CO adsorbed on films substrated on CaF₂ IR window or glassy carbon (GC) electrode yielded two strong IR absorption bands around 1970 cm⁻¹ and 1910 cm⁻¹, which were assigned to IR absorption of CO bonded on asymmetric and symmetric bridge sites, respectively. Similar IR bands were observed in spectra of CO adsorbed on films, except the IR bands were much weak, whereas CO adsorbed on film produced an IR absorption band near 1906 cm⁻¹, and an anomalous IR absorption band whose direction has been completely inverted around 1956 cm⁻¹. The direction inversion of the IR band of CO bonded to asymmetric bridge sites on was ascribed to the interaction between Pd nanoparticles inside the aggregates. Based on FTIR spectroscopic and cyclic voltammetric results, the aggregation mechanism of Pd nanoparticles from to has been suggested that the agglomeration of Pd nanoparticles was driven by the alteration of electric field across electrode-electrolyte interface, when the PVP stabilizer was stripped via oxidation during cyclic voltammetry.     

Oxygen reduction mechanism on copper in a 0.5 M H2SO4

The mechanism of the oxygen reduction reaction (ORR) in a naturally aerated stagnant 0.5 M H₂SO₄ was studied using electrochemical methods. The cathodic polarization curve showed three different regions; electrochemical impedance spectroscopy (EIS) measurement was used accordingly. The EIS data were analyzed, and the mechanism for the ORR was proposed consequently. The three regions include a limiting current density region with the main transfer of 4e⁻ controlled by diffusion (−0.50 V < E < −0.40 V), a combined kinetic-diffusion region (−0.40 V < E < −0.20 V) with an additional 2e⁻ transfer due to the adsorption of the anions, and a hump phenomenon region (−0.20 V < E < −0.05 V), in which the chemical redox between the anodic intermediate and the cathodic intermediate , together with the electrochemical reaction, synergistically results in the acceleration of the ORR. Therefore, a coupled electrochemical/chemical process (the EC mechanism) in the hump phenomenon region was proposed, and a good agreement was found between the experimental and fitted results. The EC mechanism was confirmed by the deaerated experiments.     

Analysis of the chemical diffusion coefficient of lithium ions in Li3V2(PO4)3 cathode material

The chemical diffusion coefficients of lithium ions (DLi⁺) in Li₃V₂(PO₄)₃ between 3.0 and 4.8 V are systematically determined by cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS) and galvanostatic intermittent titration technique (GITT). The DLi⁺ values are found to be dependent on the voltage state of charge and discharge. Based on the results from all the three techniques, the true diffusion coefficients measured in single-phase region are in the range of 10⁻⁹ to 10⁻¹⁰ cm² s⁻¹. Its apparent diffusion coefficients measured in two-phase regions by CV and GITT range from 10⁻¹⁰ to 10⁻¹¹ cm² s⁻¹ and 10⁻⁸ to 10⁻¹³ cm² s⁻¹, respectively, depending on the potentials. By the GITT, the DLi⁺ varies non-linearly in a “W” shape with the charge-discharge voltage, which is ascribed to the strong interactions of Li⁺ with surrounding ions. Finally, the chemical diffusion coefficients of lithium ions measured by CV, EIS and GITT are compared to each other.     

Electrocatalytic oxidation of deferiprone and its determination on a carbon nanotube-modified glassy carbon electrode

The electrochemical behavior of the anti-thalassemia and anti-HIV replication drug, deferiprone, was investigated on a carbon nanotube-modified glassy carbon (GC-CNT) electrode in phosphate buffer solution, pH 7.40 (PBS). During oxidation of deferiprone, two irreversible anodic peaks, with and , appeared, using GC-CNT. Cyclic voltammetric study indicated that the oxidation process is irreversible and diffusion controlled. The number of exchanged electrons in the electro-oxidation process was obtained, and the data indicated that deferiprone is oxidized via two two-electron steps. The results revealed that carbon nanotube (CNT) promotes the rate of oxidation by increasing the peak current, so that deferiprone is oxidized at lower potentials, which thermodynamically is more favorable. This result was confirmed by impedance measurements. The diffusion coefficient, electron-transfer coefficient and heterogeneous electron-transfer rate constant of deferiprone were found to be 1.49 × 10⁻⁶ cm² s⁻¹, 0.44, and 3.83 × 10⁻³ cm s⁻¹, respectively. A sensitive, simple and time-saving differential-pulse voltammetric procedure was developed for the analysis of deferiprone. Using the proposed method, deferiprone can be determined with a detection limit of 5.25 × 10⁻⁷ M. The applicability of the method to direct assays of spiked human serum and urine fluids is described.     

Li-ion diffusion kinetics in LiMn2O4 thin films prepared by pulsed laser deposition

LiMn₂O₄ thin films were deposited on Au substrates by pulsed laser deposition (PLD). The Li-ion chemical diffusion coefficients of the films, , were measured by cyclic voltammetry (CV), galvanostatic intermittent titration technique (GITT), potentiostatic intermittent titration technique (PITT), and electrochemical impedance spectroscopy (EIS). It was found that the values by CV and PITT were in the order of 10⁻¹³ cm² s⁻¹, and those by EIS and GITT were in the range of 10⁻¹³ to 10⁻¹¹ and 10⁻¹⁴ to 10⁻¹¹ cm² s⁻¹, respectively. These data were compared with the previously reported values.     

Codeposition of copper and tin from acid sulphate solutions containing polyether sintanol DS-10 and micromolar amounts of halides

Cu(II) and Sn(II) reduction in acid sulphate solutions containing polyether laprol DS-10 was investigated using voltammetric XPS and XRD techniques. Bright yellow bronze coatings can be deposited at potentials (E) that are positive than equilibrium potential () of Sn|Sn²⁺ electrode. Here, Sn(II) reduction might be treated as underpotential deposition (UPD) of tin on foreign (copper) substrate. Further incorporation of tin into integral Cu-Sn crystallic lattice yields the mixture of pure copper, α-CuSn phase and intermediate hexagonal hcp phase. The formation of free tin phase occurs at . This gives rise for strong inhibitive adsorption of sintanol that manifests itself in the development of deep voltammetric minimum.Addition of halides results in the shift of codeposition potential to more negative values and in the increase of copper content in the coatings deposited in the UPD region. The action of halides intensifies in the sequence Cl⁻ < Br⁻ < I⁻. If iodide concentration exceeds 2-3 μM, deposition of yellow bronze becomes impossible.     

Li-ion diffusion kinetics in LiFePO4 thin film prepared by radio frequency magnetron sputtering

LiFePO₄ thin films were prepared by radio frequency (RF) magnetron sputtering and were characterized by X-ray diffraction (XRD), scanning electron microscope (SEM) and atomic force microscope (AFM). Li-ion chemical diffusion coefficients, , were measured by potentiostatic intermittent titration technique (PITT), electrochemical impedance spectroscopy (EIS), and cyclic voltammetry (CV). The effects of Ag content, film thickness, and film orientation on the electrochemical performance and Li-ion chemical diffusion coefficients of the LiFePO₄ thin films were investigated. values were measured using the liquid electrolyte and the solid electrolyte, and the obtained values were discussed. The values by PITT and EIS were in the range of 10⁻¹⁴ to 10⁻¹² and 10⁻¹⁵ to 10⁻¹² cm² s⁻¹, respectively and that by CV was in the order of 10⁻¹⁴ cm² s⁻¹.     

A theoretical study of electrical and electrochemical properties of dicyanomethylene derivatives of squaric acid

Theoretical studies on anions of 1,2-dihydroxycyclobuten-3,4-dione (squaric acid, H₂SQ) and the whole series of dicyanomethylene derivatives in gas-phase and in acetonitrile (AN) solution are carried out using density functional theory (DFT) and SCRF-DFT method at B3LYP theory level for the first time. Natural bond orbital (NBO) analyses indicate that π-electron delocalization in the series is stronger. Based on the most stable conformations, a linear correlation was observed between the highest occupied molecular orbital (HOMO) energies, or ionization potential (I_p) and the oxidation potentials measured by cyclic voltammetry, which supports experimental results that systematic substitution of the oxygen atoms in the C₄O₄²⁻ structure with C(CN)₂ groups causes a shift of both the oxidation potentials and towards more positive values, indicating that a consistent delocalization of the negative charge is exerted by these substituents and monoanions are more resistant against oxidation than their counterparts-dianions. The correlations were also observed between experimental K_sem and Gibbs free energy calculated in AN solution. The calculated gas-phase relative basicity of the six dianions follows the order SQ²⁻ > 4-CDCB²⁻ > 2,4-CDCB²⁻ > 3,4-CDCB²⁻ > 2,3,4-CDCB²⁻ > 1,2,3,4-CDCB²⁻ which support the experimental results that the dianions SQ²⁻ and 4-CDCB²⁻ can be protonated, in strongly acidic medium, to the corresponding monoanions, whereas no protonation occurs in the case of di-, tri- and tetra-substituted compounds.     

Direct electron transfer of horseradish peroxidase on Nafion-cysteine modified gold electrode

Direct electron transfer of horseradish peroxidase, immobilized on a functional membrane-modified gold electrode, was studied. The electrode showed a quasi-reversible electrochemical redox behavior with a formal potential of 60 mV (versus Ag/AgCl) in 20 mM potassium phosphate buffer solution at pH 7.0 and temperature 25 °C. The cathodic transfer coefficient was 0.42 and electron transfer rate constant was evaluated to be 1.6 s⁻¹. Furthermore, the modified electrode was used as a biosensor and exhibited a satisfactory stability and sensitivity to H₂O₂. The linear range of this biosensor for H₂O₂ determination was from 5.0 × 10⁻⁶ to 1.5 × 10⁻⁴ M while its detection limit, based on a signal-to-noise ratio of 3, was 1.3 × 10⁻⁶ M. The apparent Michaelis-Menten constant () for immobilized HRP was calculated to be 1.6 × 10⁻⁴ M.     

Evaluation of electrical energy per order (EEO) with kinetic modeling on the removal of Malachite Green by US/UV/H2O2 process

The kinetics of decolorization of Malachite Green (MG) as a model cationic dye from textile industry, by US/UV/H₂O₂ process, was investigated with nonlinear regression analysis. The experimental results indicated that the decolorization kinetics of MG in this process fit well by pseudo-first order kinetics. With nonlinear regression analysis a model was developed for pseudo-first order constant (k_ap) as a function of operational parameters such as initial concentrations of H₂O₂ (25-600 mg l^− 1) and MG (1.82-9.87 mg l^− 1), temperature (294-307 K) and power density (0.049-0.16 W ml^− 1) as following:

     

Electrochemistry of thorium in LiCl-KCl eutectic melts

This work presents a study of the electrochemical properties of Th chloride ions dissolved in a molten LiCl-KCl eutectic, in a temperature range of 693-823 K. Transient electrochemical techniques such as cyclic voltammetry, chronopotentiommetry and chronoamperometry have been used in order to investigate the reduction mechanism on a tungsten electrode and the diffusion coefficient of dissolved Th ions. All techniques showed that only one valence state was stable in the melt. The reduction into Th metal was found to occur according to a one-step mechanism, through a nucleation-controlled process which requires an overpotential of several 100 mV. At 723 K, the diffusion coefficient is D_Th(723 K) = 3.15 ± 0.15 × 10⁻⁵ cm² s⁻¹. EMF measurements indicated that, at 723 K, the standard apparent potential is (723 K) = −2.582 V versus Cl₂/Cl⁻, and the activity coefficient γThCl₄ (723 K) = 4.6 × 10⁻⁴ on the mole fraction scale (based on a pure liquid reference state).