Deposition of F-doped ZnO transparent thin films using ZnF2-doped ZnO target under different sputtering substrate temperatures

Highly transparent and conducting fluorine-doped ZnO (FZO) thin films were deposited onto glass substrates by radio-frequency (RF) magnetron sputtering, using 1.5 wt% zinc fluoride (ZnF₂)-doped ZnO as sputtering target. Structural, electrical, and optical properties of the FZO thin films were investigated as a function of substrate temperature ranging from room temperature (RT) to 300°C. The cross-sectional scanning electron microscopy (SEM) observation and X-ray diffraction analyses showed that the FZO thin films were of polycrystalline nature with a preferential growth along (002) plane perpendicular to the surface of the glass substrate. Secondary ion mass spectrometry (SIMS) analyses of the FZO thin films showed that there was incorporation of F atoms in the FZO thin films, even if the substrate temperature was 300°C. Finally, the effect of substrate temperature on the transmittance ratio, optical energy gap, Hall mobility, carrier concentration, and resistivity of the FZO thin films was also investigated.     

Annealing of gold nanostructures sputtered on polytetrafluoroethylene

Gold nanolayers sputtered on polytetrafluoroethylene (PTFE) surface and their changes induced by post-deposition annealing at 100°C to 300°C are studied. Changes in surface morphology and roughness are examined by atomic force microscopy, electrical sheet resistance by two point technique, zeta potential by electrokinetic analysis and chemical composition by X-ray photoelectron spectroscopy (XPS) in dependence on the gold layer thickness. Transition from discontinuous to continuous gold coverage takes place at the layer thicknesses 10 to 15 nm and this threshold remains practically unchanged after the annealing at the temperatures below 200°C. The annealing at 300°C, however, leads to significant rearrangement of the gold layer and the transition threshold increases to 70 nm. Significant carbon contamination and the presence of oxidized structures on gold-coated samples are observed in XPS spectra. Gold coating leads to a decrease in the sample surface roughness. Annealing at 300°C of pristine PTFE and gold-coated PTFE results in significant increase of the sample surface roughness.     

Surface morphology and optical properties of porphyrin/Au and Au/porphyrin/Au systems

Porphyrin/Au and Au/porphyrin/Au systems were prepared by vacuum evaporation and vacuum sputtering onto glass substrate. The surface morphology of as-prepared systems and those subjected to annealing at 160°C was studied by optical microscopy, atomic force microscopy, and scanning electron microscopy techniques. Absorption and luminescence spectra of as-prepared and annealed samples were measured. Annealing leads to disintegration of the initially continuous gold layer and formation of gold nanoclusters. An amplification of Soret band magnitude was observed on the Au/meso-tetraphenyl porphyrin (TPP) system in comparison with mere TPP. Additional enhancement of luminescence was observed after the sample annealing. In the case of sandwich Au/porphyrin/Au structure, suppression of one of the two porphyrins’ luminescence maxima and sufficient enhancement of the second one were observed.     

Gold nanoparticles deposited on glass: physicochemical characterization and cytocompatibility

Properties of gold films sputtered under different conditions onto borosilicate glass substrate were studied. Mean thickness of sputtered gold film was measured by gravimetry, and film contact angle was determined by goniometry. Surface morphology was examined by atomic force microscopy, and electrical sheet resistance was determined by two-point technique. The samples were seeded with rat vascular smooth muscle cells, and their adhesion and proliferation were studied. Gold depositions lead to dramatical changes in the surface morphology and roughness in comparison to pristine substrate. For sputtered gold structures, the rapid decline of the sheet resistance appears on structures deposited for the times above 100 s. The thickness of deposited gold nanoparticles/layer is an increasing function of sputtering time and current. AFM images prove the creation of separated gold islands in the initial deposition phase and a continuous gold coverage for longer deposition times. Gold deposition has a positive effect on the proliferation of vascular smooth muscle cells. Largest number of cells was observed on sample sputtered with gold for 20 s and at the discharge current of 40 mA. This sample exhibits lowest contact angle, low relative roughness, and only mild increase of electrical conductivity.     

Bimetallic non-alloyed NPs for improving the broadband optical absorption of thin amorphous silicon substrates

We propose the use of bimetallic non-alloyed nanoparticles (BNNPs) to improve the broadband optical absorption of thin amorphous silicon substrates. Isolated bimetallic NPs with uniform size distribution on glass and silicon are obtained by depositing a 10-nm Au film and annealing it at 600°C; this is followed by an 8-nm Ag film annealed at 400°C. We experimentally demonstrate that the deposition of gold (Au)-silver (Ag) bimetallic non-alloyed NPs (BNNPs) on a thin amorphous silicon (a-Si) film increases the film''s average absorption and forward scattering over a broad spectrum, thus significantly reducing its total reflection performance. Experimental results show that Au-Ag BNNPs fabricated on a glass substrate exhibit resonant peaks at 437 and 540 nm and a 14-fold increase in average forward scattering over the wavelength range of 300 to 1,100 nm in comparison with bare glass. When deposited on a 100-nm-thin a-Si film, Au-Ag BNNPs increase the average absorption and forward scattering by 19.6% and 95.9% compared to those values for Au NPs on thin a-Si and plain a-Si without MNPs, respectively, over the 300- to 1,100-nm range.     

热处理温度对铁镍合金膜层微观结构和镀膜玻璃性能的影响

为了研究不同热处理温度下铁镍合金薄膜的形貌结构以及镀膜玻璃的性能,本文采用真空电子束加热蒸发镀膜技术在玻璃基片上镀铁镍合金薄膜,通过多晶X射线衍射(XRD)和场发射扫描电子显微镜(FESEM)分析结构,测试镀膜玻璃的光学性能、电磁性能以及电磁屏蔽性能。结果表明:随着热处理温度的升高,薄膜的结晶性能变好,逐渐析出体心立方晶相,在(110)方向具有择优取向,当热处理温度过高时薄膜中出现孔隙;热处理温度对镀膜玻璃雾度的影响小于1%,但镀膜玻璃的可见光透过率、表面方块电阻和相对磁导率会随热处理温度变化呈现一定规律变化;铁镍合金镀膜玻璃在30 MHz以下的低频电磁波频段内的屏蔽效能大于30 dB,在14 kHz时最高达到55 dB,是一种低频电磁屏蔽的优选材料。     

A catalyst-free growth of aluminum-doped ZnO nanorods by thermal evaporation

The growth of Al:ZnO nanorods on a silicon substrate using a low-temperature thermal evaporation method is reported. The samples were fabricated within a horizontal quartz tube under controlled supply of O₂ gas where Zn and Al powders were previously mixed and heated at 700°C. This allows the reactant vapors to deposit onto the substrate placed vertically above the source materials. Both the undoped and doped samples were characterized using scanning electron microscopy (SEM), field emission scanning electron microscopy (FESEM), energy-dispersive X-ray spectroscopy (EDX), high-resolution transmission electron microscopy (HRTEM) and photoluminescence (PL) measurements. It was observed that randomly oriented nanowires were formed with varying nanostructures as the dopant concentrations were increased from 0.6 at.% to 11.3 at.% with the appearance of ‘pencil-like’ shape at 2.4 at.%, measuring between 260 to 350 nm and 720 nm in diameter and length, respectively. The HRTEM images revealed nanorods fringes of 0.46 nm wide, an equivalent to the lattice constant of ZnO and correspond to the (0001) fringes with regard to the growth direction. The as-prepared Al:ZnO samples exhibited a strong UV emission band located at approximately 389 nm (E _g  = 3.19 eV) with multiple other low intensity peaks appeared at wavelengths greater than 400 nm contributed by oxygen vacancies. The results showed the importance of Al doping that played an important role on the morphology and optical properties of ZnO nanostructures. This may led to potential nanodevices in sensor and biological applications.     

Properties of gold nanostructures sputtered on glass

We studied the electrical and optical properties, density, and crystalline structure of Au nanostructures prepared by direct current sputtering on glass. We measured temperature dependence of sheet resistance and current-voltage characteristics and also performed scanning electron microscopy [SEM] analysis of gold nanolayers. It was shown that within the wide range of temperatures, gold nanolayers (<10 nm) exhibit both metal and semiconducting-like type of conductivity. UV/Vis analysis proved the semiconducting characteristic of intrinsic Au clusters. SEM analysis showed the initiatory stadium of gold layer formation to be running over isolated islands. Gold density calculated from the weight and effective thickness of the layers is an increasing function of the layer thickness up to approximately 100 nm. In thin layers deposited on solid surface, a lattice expansion is observed, which is manifested in the increase of the lattice parameter and the decrease of metal density. With increasing layer thickness, the lattice parameter and the density approach the bulk values.     

Antireflective silicon nanostructures with hydrophobicity by metal-assisted chemical etching for solar cell applications

We present broadband antireflective silicon (Si) nanostructures with hydrophobicity using a spin-coated Ag ink and by subsequent metal-assisted chemical etching (MaCE). Improved understanding of MaCE, by conducting parametric studies on optical properties, reveals a design guideline to achieve considerably low solar-weighted reflectance (SWR) in the desired wavelength ranges. The resulting Si nanostructures show extremely low SWR (1.96%) and angle-dependent SWR (<4.0% in the range of 0° to 60°) compared to that of bulk Si (SWR, 35.91%; angle-dependent SWR, 37.11%) in the wavelength range of 300 to 1,100 nm. Relatively large contact angle (approximately 102°) provides a self-cleaning capability on the solar cell surface.     

Novel Insights into Inkjet Printed Silver Nanowires Flexible Transparent Conductive Films

Silver nanowire (AgNWs) inks for inkjet printing were prepared and the effects of the solvent system, wetting agent, AgNWs suspension on the viscosity, surface tension, contact angle between ink droplet and poly(ethylene) terephthalate (PET) surface, and pH value of AgNWs ink were discussed. Further, AgNWs flexible transparent conductive films were fabricated by using inkjet printing process on the PET substrate, and the effects of the number printing layer, heat treatment temperature, drop frequency, and number of nozzle on the microstructures and photoelectric properties of AgNWs films were investigated in detail. The experimental results demonstrated that the 14-layer AgNWs printed film heated at 60 °C and 70 °C had an average sheet resistance of 13 Ω∙sq⁻¹ and 23 Ω∙sq⁻¹ and average transparency of 81.9% and 83.1%, respectively, and displayed good photoelectric performance when the inkjet printing parameters were set to the voltage of 20 V, number of nozzles of 16, drop frequency of 7000 Hz, droplet spacing of 15 μm, PET substrate temperatures of 40 °C and nozzles of 35 °C during printing, and heat treatment at 60 °C for 20 min. The accumulation and overflow of AgNWs at the edges of the linear pattern were observed, which resulted in a decrease in printing accuracy. We successfully printed the heart-shaped pattern and then demonstrated that it could work well. This showed that the well-defined pattern with good photoelectric properties can be obtained by using an inkjet printing process with silver nanowires ink as inkjet material.     

Intense ultraviolet emission from needle-like WO3 nanostructures synthesized by noncatalytic thermal evaporation

Photoluminescence measurements showed that needle-like tungsten oxide nanostructures synthesized at 590°C to 750°C by the thermal evaporation of WO₃ nanopowders without the use of a catalyst had an intense near-ultraviolet (NUV) emission band that was different from that of the tungsten oxide nanostructures obtained in other temperature ranges. The intense NUV emission might be due to the localized states associated with oxygen vacancies and surface states.     

High performance of carbon nanotubes/silver nanowires-PET hybrid flexible transparent conductive films via facile pressing-transfer technique

To obtain low sheet resistance, high optical transmittance, small open spaces in conductive networks, and enhanced adhesion of flexible transparent conductive films, a carbon nanotube (CNT)/silver nanowire (AgNW)-PET hybrid film was fabricated by mechanical pressing-transfer process at room temperature. The morphology and structure were characterized by scanning electron microscope (SEM) and atomic force microscope (AFM), the optical transmittance and sheet resistance were tested by ultraviolet-visible spectroscopy (UV-vis) spectrophotometer and four-point probe technique, and the adhesion was also measured by 3M sticky tape. The results indicate that in this hybrid nanostructure, AgNWs form the main conductive networks and CNTs as assistant conductive networks are filled in the open spaces of AgNWs networks. The sheet resistance of the hybrid films can reach approximately 20.9 to 53.9 Ω/□ with the optical transmittance of approximately 84% to 91%. The second mechanical pressing step can greatly reduce the surface roughness of the hybrid film and enhance the adhesion force between CNTs, AgNWs, and PET substrate. This process is hopeful for large-scale production of high-end flexible transparent conductive films.     

Synthesis and Characterization of ZnO Nanowire–CdO Composite Nanostructures

ZnO nanowire–CdO composite nanostructures were fabricated by a simple two-step process involving ammonia solution method and thermal evaporation. First, ZnO nanowires (NWs) were grown on Si substrate by aqueous ammonia solution method and then CdO was deposited on these ZnO NWs by thermal evaporation of cadmium chloride powder. The surface morphology and structure of the synthesized composite structures were analyzed by scanning electron microscopy, X-ray diffraction and transmission electron microscopy. The optical absorbance spectrum showed that ZnO NW–CdO composites can absorb light up to 550 nm. The photoluminescence spectrum of the composite structure does not show any CdO-related emission peak and also there was no band gap modification of ZnO due to CdO. The photocurrent measurements showed that ZnO NW–CdO composite structures have better photocurrent when compared with the bare ZnO NWs.     

Fabrication and characterization of Mn-doped CuO thin films by the SILAR method

Thin films of un-doped and Mn-doped CuO nanostructures have been deposited on glass substrates via the SILAR method. The morphological, compositional, structural and optical properties of the films have been investigated by scanning electron microscopy, energy dispersive spectroscopy, X-ray diffraction analysis and UV–vis spectrophotometry. The analyzed results indicate that the obtained films consist of plate-like nanostructures. From the EDS analysis it is seen that Mn-doping concentration affects the shapes of the nanostructures. XRD results show that all of the films have monoclinic structure. From the room temperature UV–vis analysis it is found that the optical band gap of the films increases with increasing Mn-doping concentrations.     

Effects of starting powder and thermal treatment on the aerosol deposited BaTiO3 thin films toward less leakage currents

To prepare high-density integrated capacitors with low leakage currents, 0.2-μm-thick BaTiO₃ thin films were successfully deposited on integrated semiconductor substrates at room temperature by the aerosol deposition (AD) method. In this study, the effects of starting powder size were considered in an effort to remove macroscopic defects. A surface morphology of 25.3 nm and an interface roughness of less than 50 nm were obtained using BT-03B starting powder. The nano-crystalline thin films achieved after deposition were annealed at various temperatures to promote crystallization and densification. Moreover, the influence of rapid thermal annealing process on the surface morphology and crystal growth was evaluated. As the annealing temperature increased from room temperature to 650°C, the root mean square (RMS) roughness decreased from 25.3 to 14.3 nm. However, the surface was transformed into rough performance at 750°C, which agreed well with the surface microstructure trend. Moreover, the crystal growth also reveals the changes in surface morphology via surface energy analysis.     

Oxygen Distribution of Fluorine-doped Tin Oxide Films Coated on Float Glass along Depth Before and After Heat Treatment

Fluorine-doped tin oxide (FTO) films were deposited on float glass to create low-emissivity glass (low-E glass) by atmospheric pressure chemical vapor deposition (APCVD). Heat treatments were carried out to assess its antioxidant properties. The surface morphology, crystal structure, and the oxygen and tin concentrations in the FTO films were investigated by scanning electron microscope (SEM), X-ray diffraction (XRD), Auger electron spectrometer (AES), and X-ray photoelectron spectroscopy (XPS), respectively. The results indicated that the electrical properties determined by the four-point probe method remained constant up to 600°C with increasing temperature. The FTO films exhibited nonstoichiometry with a ratio of [O]/[Sn] >2 on the top surface and <2 in the film. The sheet resistance of the film strongly depended on the oxygen concentration on the film surface. When the heating temperature reached 700°C, the sheet resistance increased rapidly from 9.4 to 86.7 Ω/□ with a concomitant increase in the oxygen concentration on the top surface.     

Transparent Conducting Electrodes from Conducting Polymer Nanofibers and Their Application as Thin‐Film Heaters

Transparent conducting electrodes attract attention in relation to solar cells, touch panels, displays, e‐readers, and transparent heaters. In many cases, rarefied metal nets with optical transmittance of ≈90% and with minimal sheet resistance are sought after. Here, a mesh of conducting polymer nanofibers is developed as a transparent conducting electrode. A sheet resistance of 8.4 kΩ sq⁻¹ with 84% optical transmittance is achieved with polyethylene oxide/poly(3,4‐ethylenedioxythiophene) polystyrene sulfonate (PEO/PEDOT:PSS) blended polymer nanofibers. This study also demonstrates that such nanofiber being deposited on a glass substrate can be used as a transparent film heater in relevant applications such as window heating or displays at harsh environments. Such a transparent heater is rated at 0.41 W in.⁻² for 120 V. It is also capable of heating a substrate up to ≈70 °C in 4 min at 60 V from room temperature without any degeneration of nanofiber network, rendering itself as a practically useful transparent heater. The performance of the PEO/PEDOT:PSS nanofiber‐coated transparent glass heater is comparable to that of the relatively expensive indium tin oxide thin‐film heaters.     

Improved optical and structural properties of cadmium sulfide nanostructures for optoelectronic applications

In this study, the effect of ZnO seed layer on the growth of uniform CdS nanostructures was investigated using chemical bath deposition technique. Besides, the influence of molar concentration of reagents on the surface morphology, structural and optoelectrical properties of the deposited CdS thin films were examined. The CdS nanostructures were grown on bare glass and ZnO/glass substrates with different reagent molar concentrations. The results indicated an improvement in the homogeneity and uniformity of the grown CdS nanostructures on ZnO seed layer which can be due to the low lattice mismatch between ZnO and CdS structures. The CdS/ZnO samples were optimized by changing the molar concentration of reagents. A three–dimensional intersecting vertical nanosheet morphology with hexagonal structure was obtained when modified chemical concentration of 0.5 M was applied. The XRD pattern of CdS nanosheets indicated the hexagonal phase of CdS which were strongly orientated along (002) plane. The elevated intensity of dominant peak related to this sample confirmed the improved crystal quality of this CdS nanostructure comparing to the other samples. The UV–Vis spectrum demonstrated a high absorption coefficient for CdS intersecting nanosheets which might be due to the high specific surface area and light trapping behavior of this sample. The photoluminescence study also showed an improvement in optical properties of optimized CdS nanostructures. In order to study the optoelectrical properties of CdS nanostructures, metal–semiconductor–metal photodetectors were fabricated with different CdS samples and their current–voltage characteristics were analyzed. The results indicated an enhancement in photosensitivity, responsivity, and speed of photodetectors based on optimized CdS nanostructures.     

Engineering of morphological,optical, structural,photocatalytic and catalytic properties of nanostructured CuO thin films fabricated by reactive DC magnetron sputtering

Nanostructured thin films of CuO were deposited on silica glass substrates using reactive DC magnetron sputtering technique. Microstructural, morphological, optical, catalytic and photocatalytic properties of the prepared CuO thin films were examined using FESEM, AFM, Rutherford backscattering spectrometry, XRD, XPS, UV–Vis absorption and PL spectroscopy. FESEM showed nanostructures in the thin films, which were confirmed to be of monoclinic CuO by XRD analysis. Substrate temperature variation (40 °C, 100 °C and 300 °C) was found to significantly alter the optical, morphological, photocatalytic and structural properties of the CuO nanostructured thin film coatings. FESEM and AFM analyses showed decrease in size of nanostructures and surface roughness increase with increase in substrate temperature. Increase in UV–Vis absorbance and PL intensity of CuO thin films with decrease in crystallite size were noticed as the substrate temperature was increased. The prepared nanostructured CuO thin films exhibited highly enhanced photocatalytic activities and degraded dyes (MB and MO) in water in just 40 min under solar exposure and catalytic transformation of 4-nitrophenol (4-NP) took place in just 15 min. The developed CuO nanostructured thin film coatings are very promising for large scale, practical and advanced catalytic reduction of toxic 4-NP and photocatalytic applications in solar driven water purification.     

Direct formation of gold nanoparticles on substrates using a novel ZnO sacrificial templated-growth hydrothermal approach and their properties in organic memory device

This study describes a novel fabrication technique to grow gold nanoparticles (AuNPs) directly on seeded ZnO sacrificial template/polymethylsilsesquioxanes (PMSSQ)/Si using low-temperature hydrothermal reaction at 80°C for 4 h. The effect of non-annealing and various annealing temperatures, 200°C, 300°C, and 400°C, of the ZnO-seeded template on AuNP size and distribution was systematically studied. Another PMMSQ layer was spin-coated on AuNPs to study the memory properties of organic insulator-embedded AuNPs. Well-distributed and controllable AuNP sizes were successfully grown directly on the substrate, as observed using a field emission scanning electron microscope followed by an elemental analysis study. A phase analysis study confirmed that the ZnO sacrificial template was eliminated during the hydrothermal reaction. The AuNP formation mechanism using this hydrothermal reaction approach was proposed. In this study, the AuNPs were charge-trapped sites and showed excellent memory effects when embedded in PMSSQ. Optimum memory properties of PMMSQ-embedded AuNPs were obtained for AuNPs synthesized on a seeded ZnO template annealed at 300°C, with 54 electrons trapped per AuNP and excellent current–voltage response between an erased and programmed device.