Layer-by-layer assemblies of chitosan/multi-wall carbon nanotubes and glucose oxidase for amperometric glucose biosensor applications

A novel amperometric glucose biosensor based on multilayer films containing chitosan, multi-wall carbon nanotubes (MWCNTs) and glucose oxidase (GOD) was developed. MWCNTs were solubilized in chitosan (Chit-MWCNTs) used to interact with GOD. Poly (allylamine) (PAA) and polyvinylsulfuric acid potassium salt (PVS) were alternately deposited on the cleaned Pt electrode surface ((PVS/PAA)₃/Pt). The (PVS/PAA)₃/Pt electrode was alternately immersed in Chit-MWCNTs and GOD to assemble different layers of multilayer films. PBS washing was applied at the end of each assembly deposition for dissociating the weak adsorption. Micrographs of MWCNTs were obtained by scanning electron microscope, and properties of the resulting biosensors were measured by electrochemical measurements. Among the resulting biosensors, the biosensor based on eight layers of multilayer films was best. The resulting biosensor was able to efficiently monitor glucose, with the response time within 8 s, a detection limit of 21 μM estimated at a signal-to-noise ratio of 3, a linear range of 1–10 mM, the sensitivity of 0.45 μA/mM, and well stability. The study can provide a feasible simple approach on developing a new immobilization matrix for biosensors and surface functionalization.     

Preparation of Pt/multiwalled carbon nanotubes modified Au electrodes via Pt–Cu co-electrodeposition/Cu stripping protocol for high-performance electrocatalytic oxidation of methanol

Pt nanoparticles well dispersed on multiwalled carbon nanotubes (MWCNTs) were prepared for high-performance electrocatalytic oxidation of methanol in both acidic and alkaline media via the co-electrodeposition/stripping (CS) protocol, namely, co-electrodeposition of Pt and Cu followed by electrochemical stripping of Cu, as examined by cyclic voltammetry (CV), electrochemical quartz crystal microbalance (EQCM), scanning electron microscopy (SEM), and X-ray diffraction (XRD). The Pt catalyst prepared by the CS protocol on MWCNTs (Pt_cs/MWCNTs/Au) exhibited a specific electrocatalytic activity of 519 and 2210 A g⁻¹ toward cyclic voltammetric electrooxidation (50 mV s⁻¹) of methanol in 0.5 M CH₃OH + 0.5 M H₂SO₄ and 0.5 M CH₃OH + 1.0 M NaOH media, respectively, which are larger than those prepared by conventional electrodeposition from chloroplatinic acid on Au and MWCNTs/Au, as well as that by a CS protocol on Au. The Pt_cs/MWCNTs/Au electrode also possessed the highest stability, which maintained 91% and 90% of its initial catalytic activity after 120-cycle CV in 0.5 M CH₃OH + 0.5 M H₂SO₄ and 0.5 M CH₃OH + 1.0 M NaOH, respectively. The electrode kinetics of methanol oxidation is also briefly discussed. The nanosubstrate-based CS protocol is simple, convenient and efficient, which is expected to find wide applications in film electrochemistry and electrocatalysis.     

Electrodeposition of chitosan-glucose oxidase biocomposite onto Pt-Pb nanoparticles modified stainless steel needle electrode for amperometric glucose biosensor

A glucose biosensor was fabricated by electrodepositing chitosan (CS)-glucose oxidase(GOD) biocomposite onto the stainless steel needle electrode (SSN electrode) modified by Pt–Pb nanoparticles (Pt–Pb/SSN electrode). Firstly, Pt–Pb nanoparticles were deposited onto the SSN electrode and then CS-GOD biocomposite was co-electrodeposited onto the Pt–Pb/SSN electrode in a mixed solution containing p-benzoquinone (p-BQ), CS and GOD. The electrochemical results showed that the Pt–Pb nanoparticles can accelerate the electron transfer and improve the effective surface area of the SSN electrode. As a result, the detection range of the proposed biosensor was from 0.03 to 9 mM with a current sensitivity of 0.4485 μA/mM and a response time of 15 s. The Michaelis constant value was calculated to be 4.9837 mM. The cell test results indicated that the electrodes have a low cytotoxicity. This work provided a suitable technology for the fabrication of the needle-type glucose biosensor.     

Glucose biosensor from covalent immobilization of chitosan-coupled carbon nanotubes on polyaniline-modified gold electrode

An amperometric glucose biosensor was prepared using polyaniline (PANI) and chitosan-coupled carbon nanotubes (CS-CNTs) as the signal amplifiers and glucose oxidase (GOD) as the glucose detector on a gold electrode (the Au-g-PANI-c-(CS-CNTs)-GOD biosensor). The PANI layer was prepared via oxidative graft polymerization of aniline from the gold electrode surface premodified by self-assembled monolayer of 4-aminothiophenol. CS-CNTs were covalently coupled to the PANI-modified gold substrate using glutaradehyde as a bifunctional linker. GOD was then covalently bonded to the pendant hydroxyl groups of chitosan using 1,4-carbonyldiimidazole as the bifunctional linker. The surface functionalization processes were ascertained by X-ray photoelectron spectroscopy (XPS) analyses. The field emission scanning electron microscopy (FESEM) images of the Au-g-PANI-c-(CS-CNTs) electrode revealed the formation of a three-dimensional surface network structure. The electrode could thus provide a more spatially biocompatible microenvironment to enhance the amount and biocatalytic activity of the immobilized enzyme and to better mediate the electron transfer. The resulting Au-g-PANI-c-(CS-CNTs)-GOD biosensor exhibited a linear response to glucose in the concentration range of 1-20 mM, good sensitivity (21 μA/(mM·cm(2))), good reproducibility, and retention of >80% of the initial response current after 2 months of storage.     

用单壁纳米碳管制备葡萄糖生物传感器的研究

以单壁纳米碳管为代表材料,对利用纳米碳管制备葡萄糖生物传感器中纳米碳管的作用和纳米碳管修饰电极的方法、酶的固定化方法及电极种类等因素对传感器性能的影响进行了研究.研究结果表明,纳米碳管的加入能有效地改善传感器的电化学性能,利用二茂铁和单壁纳米碳管共同修饰电极所制得的传感器的性能要好于仅用单壁纳米碳管修饰电极制得的传感器.在酶的固定化方法中,戊二醛交联法要略好于明胶包埋法;而利用铂电极制备出的生物传感器对葡萄糖的响应电流要明显高于利用金电极和玻碳电极制备出的生物传感器.这些结论对于开发纳米碳管在生物传感领域及生命科学相关领域的应用有参考价值.     

A cholesterol biosensor based on gold nanoparticles decorated functionalized graphene nanoplatelets

The fabrication of a cholesterol biosensor using gold nanoparticles decorated graphene nanoplatelets has been reported. Thermally exfoliated graphene nanoplatelets act as a suitable support for the deposition of Au nanoparticles. Cholesterol biosensor electrodes have been constructed with nafion solubilized functionalized graphene nanoplatelets (f-G) as well as Au nanoparticles decorated f-G, immobilized over glassy carbon electrode. f-G and Au/f-G thin film deposited glassy carbon electrodes were further functionalized with cholesterol oxidase by physical adsorption. Au nanoparticles dispersed over f-G demonstrate the ability to substantially raise the response current. The fabricated electrodes have been tested for their electrochemical performance at a potential of 0.2 V. The fabricated Au/f-G based cholesterol biosensor exhibits sensitivity of 314 nA/μM cm² for the detection of cholesterol with a linear response up to 135 μM. Furthermore, it has been observed that the biosensor exhibits a good anti-interference ability and favorable stability over a month's period.     

Study of different carbon materials for amperometric enzyme biosensor development

Diamond-like carbon (DLC) electrodes which constitute a new research area in electrochemistry and glassy carbon (GC) electrodes were used as transducers for fabrication of glucose oxidase (GOD) biosensors. The amperometric signal of the enzyme electrode was due to the electro-oxidation of H₂O₂ generated in the enzyme layer. This work has shown that the detection limit of glucose on GOD/GC electrode is 20 μM while it is 50 μM on GOD/DLC electrode. The sensitivity of GOD/GC electrode decreases 4% after 8 days and we have good repeatability of measurements for GOD/DLC electrode in the same day.     

An effective gold nanotubes electrode for amperometric biosensor

A sensitive and effective amperometric glucose biosensor based on gold nanotubes electrode (GNTE) was investigated. Gold nanotubes (GNTs), which were prepared by electroless plating of the metal within the pores of nanoporous polycarbonate (PC) track-etched membranes, were filled into a hollow teflon cylinder to construct a GNTE. Glucose oxidase (GOD) was immobilized on the electrode via glutaraldehyde cross-linkage method. The electrochemical properties were investigated by cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS). The km value of the immobilized glucose oxidase on GNTE was 0.47 mM. The biosensor showed a linear range from 0.4 to 11 mM with excellent sensitivity of 8.77 microA cm(-2) mM(-1) and fast response time within 5 s.     

壳聚糖凝胶材料固定葡萄糖氧化酶制电极的研究

以壳聚糖为载体研究凝胶法固定葡萄糖氧化酶制电极。试验研究了载体壳聚糖的降解性；交联剂戊二醛的浓度、用量；电极的载酶量等固定化条件对所组建的传感器性能的影响。通过影响规律的分析、优化固定化条件的研究，找出了根据壳聚糖溶液粘度适当调整交联剂成二醛的用量和铂丝在酶膜母液中浸涂时间，克服壳聚糖的降解性对酶电极性能的影响，建立了制备性能相近的GOD传感器的方法。     

Direct electron transfer and biosensing of glucose oxidase immobilized at multiwalled carbon nanotube-alumina-coated silica modified electrode

Investigations are reported regarding the direct electrochemical performance of glucose oxidase (GOD) immobilized on a film of multiwalled carbon nanotube-alumina-coated silica (MWCNT-ACS). The surface morphology of the GOD/MWCNT-ACS nanobiocomposite is characterized by scanning electron microscopy. In cyclic voltammetric response, the immobilized GOD displays a pair of well-defined redox peaks, with a formal potential (E°′) of ? 0.466 V versus Ag/AgCl in a 0.1 M phosphate buffer solution (pH 7.5) at a scan rate of 0.05 V s^? 1; also the electrochemical response indicates a surface-controlled electrode process. The dependence of formal potential on solution pH indicates that the direct electron transfer reaction of GOD is a reversible two-electron coupled with a two-proton electrochemical reaction process. The glucose biosensor based on the GOD/MWCNT-ACS nanobiocomposite shows a sensitivity of 0.127 A M^? 1 cm^? 2 and an apparent Michaelis–Menten constant of 0.5 mM. Furthermore, the prepared biosensor exhibits excellent anti-interference ability to the commonly co-existed uric acid and ascorbic acid.     

Glucose oxidase electrodes of polyaniline,poly(<Emphasis Type="Italic">o</Emphasis>-anisidine) and their co-polymer as a biosensor: a comparative study

Polyaniline (PA), poly(o-anisidine) (POA) and their co-polymer poly(aniline-co-o-anisidine) (PA-co-POA) thin films were electropolymerized in solution containing 0.1 M monomer(s) and 1 M H₂SO₄ as a electrolyte by applying sequential linear potential scan rate 50 mV/s between −0.2 and 1.0 V vs. Ag/AgCl electrode on platinum electrode. A simple technique is described for constructing a glucose sensor by the entrapment of glucose oxidase (GOD) in PA, POA and their co-polymer PA-co-POA thin films, which were electrochemically deposited on a platinum plate in phosphate and acetate buffer. The maximum current response was observed for PA, POA, and PA-co-POA GOD electrodes at pH 5.5 and potential 0.60 V (vs. Ag/AgCl). The phosphate buffer gives fast response as compared to acetate buffer in amperometric measurements. PA GOD electrode shows fast response (means time taken for sense the glucose is lees) followed by PA-co-POA and POA GOD electrodes.     

Electrochemical biosensor based on integrated assembly of dehydrogenase enzymes and gold nanoparticles

Development of a highly sensitive nanostructured electrochemical biosensor based on the integrated assembly of dehydrogenase enzymes and gold (Au) nanoparticle is described. The Au nanoparticles (AuNPs) have been self-assembled on a thiol-terminated, sol-gel-derived, 3-D, silicate network and enlarged by hydroxylamine seeding. The AuNPs on the silicate network efficiently catalyze the oxidation of NADH with a decrease in overpotential of approximately 915 mV in the absence of any redox mediator. The surface oxides of AuNP function as an excellent mediator, and a special inverted "V" shape voltammogram at less positive potential was observed for the oxidation of NADH. The AuNP self-assembled sol-gel network behaves like a nanoelectrode ensemble. The nanostructured electrode shows high sensitivity (0.056 +/- 0.001 nA/nM) toward NADH with an amperometric detection limit of 5 nM. The electrode displays excellent operational and storage stability. A novel methodology for the fabrication of a NADH-dependent dehydrogenase biosensor based on the integration of dehydrogenase enzyme and AuNPs with the silicate network is developed. The enzymatically generated NADH is, in turn, electrocatalytically detected by the AuNPs on the silicate network. The integrated assembly has been successfully used for the amperometric biosensing of lactate and ethanol at a potential of -5 mV. The biosensor is very stable and highly sensitive, and it has a fast response time. The excellent performance validates the integrated assembly as an attractive sensing element for the development of new dehydrogenase biosensors.     

Multiwalled carbon nanotube-poly(vinyl alcohol)-glucose oxidase nanobiocomposites for amperometric sensing

Novel nanobiocomposites multiwalled carbon nanotube-poly(vinyl alcohol)-glucose oxidase have been successfully prepared by a simple solution-evaporation method. The morphology and performance of the multiwalled carbon nanotube-poly(vinyl alcohol)-glucose oxidase film have been characterized by atomic force microscopy, cyclic voltammetry, and amperometry. The multiwalled carbon nanotube and glucose oxidase were observed to be homogeneously dispersed throughout the poly(vinyl alcohol) matrix. When compared with bare glassy carbon electrode, the sensitivity to hydrogen peroxide is greatly improved by about 115 times at multiwalled carbon nanotubepoly(vinyl alcohol) modified glassy carbon electrode. The glucose biosensor sensitivity was strongly influenced by the glucose oxidase concentration within the multiwalled carbon nanotube-poly(vinyl alcohol)-glucose oxidase composite.     

DNA as a support for glucose oxidase immobilization at Prussian blue-modified glassy carbon electrode in biosensor preparation

An amperometric glucose biosensor has been developed using DNA as a matrix of Glucose oxidase (GOx) at Prussian-blue (PB)-modified glassy carbon (GC) electrode. GC electrode was chemically modified by the PB. GOx was immobilized together with DNA at the working area of the PB-modified electrode by placing a drop of the mixture of DNA and GOx. The response of the biosensor for glucose was evaluated amperometrically. Upon immobilization of glucose oxidase with DNA, the biosensor showed rapid response toward the glucose. On the other hand, no significant response was obtained in the absence of DNA. Experimental conditions influencing the biosensor performance were optimized and assessed. This biosensor offered an excellent electrochemical response for glucose concentration in micro mol level with high sensitivity and selectivity and short response time. The levels of the relative standard deviation (RSDs), (<4%) for the entire analyses reflected a highly reproducible sensor performance. Through the use of optimized conditions, a linear relationship between current and glucose concentration was obtained up to 4 x 10(-4) M. In addition, this biosensor showed high reproducibility and stability.     

Electrochemical behavior of gold nanoparticles modified nitrogen incorporated tetrahedral amorphous carbon and its application in glucose sensing

Gold nanoparticles (NPs) with 10-50 nm in diameter were synthesized on nitrogen incorporated tetrahedral amorphous carbon (ta-C:N) thin film electrode by electrodeposition. The deposition and nucleation processes of Au on ta-C:N surface were investigated by cyclic voltammetry and chronoamperometry. The morphology of Au NPs was characterized by scanned electron microscopy. The electrochemical properties of Au NPs modified ta-C:N (ta-C:N/Au) electrode and its ability to sense glucose were investigated by voltammetric and amperometric measurements. The potentiostatic current-time transients showed a progressive nucleation process and diffusion growth of Au on the surface of ta-C:N film according to the Scharifker-Hills model. The Au NPs acted as microelectrodes improved the electron transfer and electrocatalytic oxidation of glucose on ta-C:N electrode. The ta-C:N/Au electrode exhibited fast current response, a linear detection range of glucose from 0.5 to 25 mM and a detection limit of 120 microM, which hinted its potential application as a glucose biosensor.     

Development of an amperometric l-lactate biosensor based on l-lactate oxidase immobilized through silica sol–gel film on multi-walled carbon nanotubes/platinum nanoparticle modified glassy carbon electrode

Platinum nanoparticles (Ptnano) were used in combination with multi-walled carbon nanotubes (MWCNTs) for fabricating sensitivity-enhanced electrochemical l-lactate biosensor. The composite film of MWCNTs and Ptnano was dispersed on the surface of the glassy carbon electrode (GCE). l-lactate oxidase (LOD) was immobilized on MWCNTs/Ptnano/GCE surface by adsorption. The resulting LOD/MWCNTs/Ptnano electrode was covered by a thin layer of sol–gel to avoid the loss of LOD in determination and to improve the anti-interferent ability. Moreover, the sol–gel microenviroment contributes to both intensified stability and permselectivity. The cyclic voltammetry results indicated that MWCNTs/Ptnano catalyst displayed a higher performance than MWCNTs. Under the optimized conditions of applied potential 0.5 V, pH 6.4, room temperature, the proposed biosensor showed a large determination range (0.2–2.0 mM), a short response time (within 5 s), a high sensitivity (6.36 μA mM^{− 1}) and good stability (90% remains after 4 weeks). The fabricated biosensor had practically good selectivity against interferences. The results for whole blood samples measured by the present biosensor showed a good agreement with those measured by spectrophotometric method.     

Development of bimetal-grown multi-scale carbon micro-nanofibers as an immobilizing matrix for enzymes in biosensor applications

This study describes the development of a novel bimetal (Fe and Cu)-grown hierarchical web of carbon micro-nanofiber-based electrode for biosensor applications, in particular to detect glucose in liquids. Carbon nanofibers (CNFs) are grown on activated carbon microfibers (ACFs) by chemical vapor deposition (CVD) using Cu and Fe as the metal catalysts. The transition metal-fiber composite is used as the working electrode of a biosensor applied to detect glucose in liquids. In such a bi-nanometal-grown multi-scale web of ACF/CNF, Cu nanoparticles adhere to the ACF-surface, whereas Fe nanoparticles used to catalyze the growth of nanofibers attach to the CNF tips. By ultrasonication, Fe nanoparticles are dislodged from the tips of the CNFs. Glucose oxidase (GOx) is subsequently immobilized on the tips by adsorption. The dispersion of Cu nanoparticles at the substrate surface results in increased conductivity, facilitating electron transfer from the glucose solution to the ACF surface during the enzymatic reaction with glucose. The prepared Cu-ACF/CNF/GOx electrode is characterized for various surface and physicochemical properties by different analytical techniques, including scanning electron microscopy (SEM), electron dispersive X-ray analysis (EDX), Fourier-transform infrared spectroscopy (FTIR), BET surface area analysis, and transmission electron microscopy (TEM). The electrochemical tests show that the prepared electrode has fast response current, electrochemical stability, and high electron transfer rate, corroborated by CV and calibration curves. The prepared transition metal-based carbon electrode in this study is cost-effective, simple to develop, and has a stable immobilization matrix for enzymes.     

纳米纤维素/碳纳米管/纳米银线柔性电极的制备

目的以竹粉为原料制备纳米纤维素,并将其作为基底材料制备纳米纤维素/碳纳米管/纳米银线复合电极,应用于柔性超级电容器。方法采用化学机械处理法,将竹粉通过化学处理以及研磨、超声等处理,制备成纳米纤维素悬浮液;分别将多壁碳纳米管和纳米银线超声分散于溶剂中;最后,通过层层自组装制备纳米纤维素/碳纳米管/纳米银线复合电极,同时,作为对照组,制备纳米纤维素/碳纳米管复合电极。结果纳米纤维素纤丝的直径大约为30~100 nm,相互之间缠绕成网状结构,是很好的支撑材料,纳米纤维素/碳纳米管/纳米银线复合电极具有很好的成膜性和电化学性能,在扫描速率为30 m V/s时,面积比电容达到77.95 m F/cm~2。结论以纳米纤维素为基底,通过层层自组装方法制备的纳米纤维素/碳纳米管/纳米银线复合电极具有较好的电化学性能,可作为柔性超级电容器的电极。     

GOD/PPy/GC电极的电化学性能研究

采用电沉积法在玻碳(GC)电极表面合成纳米级聚吡咯(PPy),通过扫描电镜得到PPy的形貌。以PPy为载体,通过吸附法固定葡萄糖氧化酶(GOD),得到GOD/PPy/GC电极。利用循环伏安法对GOD/PPy/GC电极的电化学行为进行分析,结果表明,以PPy为载体可以很好地固定GOD并保持其生物活性。在0.1mol/L磷酸盐缓冲溶液中,无任何电子媒介体存在时,GOD/PPy/GC电极显示了很好的电催化性能。     

Enzyme electrodes with conductive polymer membranes and Langmuir-Blodgett films

A glucose sensor consisting of a conductive polypyrrole membrane and a lipid Langmuir-Blodgett (LB) film has been investigated. Different arrangements of the biosensor on the electrodes examined were (1) electrode with glucose oxidase (GOD)-immobilized lipid LB films; (2) GOD-immobilized LB film coated on polypyrrole-modified electrode; (3) electrode with a GOD-immobilized polypyrrole membrane; (4) GOD-immobilized LB film coated on a GOD-polypyrrole-modified electrode. It was shown that the quality of the biosensor was apparently improved in case (4) with respect to both the detectable concentration range of glucose and the lifetime over which it could be used. The number of layers of the LB film has a marked influence on the sensitivity of the biosensor, an optimum number of layers existing for the best response. The mechanism of such an improvement is discussed.